Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Modeling and analysis of solvent removal during Li-ion battery electrode drying

In this paper, we study the design aspects and process dynamics of solvent removal from Lithium-ion battery electrode coatings. For this, we use a continuum level mathematical model to describe the physical phenomenon of cathode drying involving coupled simultaneous heat and mass transfer with phase change. Our results indicate that around 90% of solvent is removed in less than half of the overall drying time. We study the effect of varying temperature and air velocity on the drying process. We show that the overall drying energy can be reduced by at least 50% by using a multi-zone drying process. Also, the peak solvent flux can be reduced by at least 40%. We further present the effect of using an aqueous solvent instead of N-Methyl-2-pyrrolidone (NMP) in electrode drying. Our results indicate that Water dries nearly 4.5 times faster as compared to NMP and requires nearly 10 times less overall drying energy per kg of solvent.

25 ENERGY STORAGE↗

Effect of SOFC Interconnect-Coating Interactions on Coating Properties and Performance

The high operating temperature of solid oxide fuel cells (SOFCs) provides good fuel flexibility which expands potential applications, but also creates materials challenges. One such challenge is the interconnect material, which was the focus of this project. In particular, the objective of the project was to understand the interaction between the interconnect alloy and ceramic coatings which are needed to minimize chromium volatilization and the associated chromium poisoning of the SOFC cathode.

36 MATERIALS SCIENCE↗

500 Wh/Kg Batteries with fluoride conversion cathodes and LiPON-Protected Li Anodes (Final Report)

The objective of this project is to research, develop, and demonstrate a Li-C@LiPON/Fe 1.0-y M y OF battery supported by fluorinated functional liquid electrolytes capable of achieving an energy density ≥500 Wh/Kg while achieving a 1,000-cycle life. The PIs developed an all-fluorinated electrolyte that can suppress Li dendrite and achieve 99.2% of coulumbic efficiency for Li plating/stripping by forming LiF-rich SEI on Li anode. The electrolyte can also stabilize the modified Fe 0.9 Co 0.1 F 3 cathode to reach energy density of >1000 Wh/kg. Using porous carbon as a Li host and coating with ORNL’s LiPON further enhanced Li plating/stripping efficiency by restricting Li volume change to less than 20%.

25 ENERGY STORAGE↗

High-Efficiency Artificial Photosynthesis Using a Novel Alkaline Membrane Cell

A new cell designed to mimic the photosynthetic processes of plants to convert carbon dioxide into carbonaceous products and oxygen at high efficiency, has an improved configuration using a polymer membrane electrolyte and an alkaline medium. This increases efficiency of the artificial photosynthetic process, achieves high conversion rates, permits the use of inexpensive catalysts, and widens the range of products generated by this type of process. The alkaline membrane electrolyte allows for the continuous generation of sodium formate without the need for any additional separation system. The electrolyte type, pH, electrocatalyst type, and cell voltage were found to have a strong effect on the efficiency of conversion of carbon dioxide to formate. Indium electrodes were found to have higher conversion efficiency compared to lead. Bicarbonate electrolyte offers higher conversion efficiency and higher rates than water solutions saturated with carbon dioxide. pH values between 8 and 9 lead to the maximum values of efficiency. The operating cell voltage of 2.5 V, or higher, ensures conversion of the carbon dioxide to formate, although the hydrogen evolution reaction begins to compete strongly with the formate production reaction at higher cell voltages. Formate is produced at indium and lead electrodes at a conversion efficiency of 48 mg of CO2/kilojoule of energy input. This efficiency is about eight times that of natural photosynthesis in green plants. The electrochemical method of artificial photosynthesis is a promising approach for the conversion, separation and sequestration of carbon dioxide for confined environments as in space habitats, and also for carbon dioxide management in the terrestrial context. The heart of the reactor is a membrane cell fabricated from an alkaline polymer electrolyte membrane and catalyst- coated electrodes. This cell is assembled and held in compression in gold-plated hardware. The cathode side of the cell is supplied with carbon dioxide-saturated water or bicarbonate solution. The anode side of the cell is supplied with sodium hydroxide solution. The solutions are circulated past the electrodes in the electrochemical cell using pumps. A regulated power supply provides the electrical energy required for the reactions. Photovoltaic cells can be used to better mimic the photosynthetic reaction. The current flowing through the electrochemical cell, and the cell voltage, are monitored during experimentation. The products of the electrochemical reduction of carbon dioxide are allowed to accumulate in the cathode reservoir. Samples of the cathode solution are withdrawn for product analysis. Oxygen is generated on the anode side and is allowed to vent out of the reservoir.

Narayan, Sri↗

Catalyst layer formulations for slot-die coating of PEM fuel cell electrodes

The series of electrodes were fabricated by the scalable and manufacturable slot-die coating method for proton exchange membrane fuel cell (PEMFC) application. The inks with different amounts of solids were studied by rheological methods in order to establish a coating window with minimum manufacturing defects. The obtained electrodes were characterized by SEM, AFM, and optical microscopy, which showed that they were uniform and homogeneous with minimum defects. The electrochemical evaluation of the manufactured gas diffusion electrodes (GDE) showed that the main characteristics of the electrodes, like electrochemical surface area, proton resistivity, and double layer capacitance, were found to be close for all samples confirming the reproducibility of the slot-die process. Additionally, we studied the effects of membrane thickness on the performance of the GDE membrane electrode assemblies and determined that a decrease in membrane thickness favored the performance. Furthermore, the obtained results clearly demonstrated the applicability and feasibility of the approach for the Manufacturing of catalyst layers for the fuel cell application with potential for future mass production.

08 HYDROGEN↗

Understanding cation doping achieved by atomic layer deposition for high-performance Li-Ion batteries

As Li ion battery (LIB) technology develops, its nanoscale design is attracting more and more interest. Atomic layer deposition (ALD) has emerged as a promising technique to provide conformal and ultrathin coating for LIB materials. In this work, an iron oxide (FeO x ) ALD was performed on LiMn 1.5 Ni 0.5 O-5 4 (LMNO) cathode particles, followed by an annealing process. Here, Fe was doped into LMNO during the ALD process; and it was found that lattice oxygen loss and structural change of LMNO occurred at a reaction temperature of 450 °C under vacuum. Meanwhile, Fe diffused from the surface to the bulk of LMNO. After post-annealing, FeO x -coated LMNO recovered its structure and lattice oxygen under proper annealing conditions, and exhibited significant enhancement of specific capacity, rate capability, and cyclic stability.

25 ENERGY STORAGE↗

30 Years of Lithium-Ion Batteries

Over the past 30 years, significant commercial and academic progress has been made on Li-based battery technologies. From the early Li-metal anode iterations to the current commercial Li-ion batteries (LIBs), the story of the Li-based battery is full of breakthroughs and back tracing steps. This review will discuss the main roles of material science in the development of LIBs. As LIB research progressed and the materials of interest changed, different emphasis on the different sub-disciplines of material science were placed. Early works on LIBs focused more on solid state physics whereas near the end of the 20th century with nanotechnology on the rise, researchers began to focus more on the morphological aspects (surface coating, porosity, size and shape) of electrode materials. While it is easy to point out which specific cathode and anode materials are currently good candidates for the next-generation of batteries, it is difficult to explain exactly why those were chosen. We hope to clearly draw for the reader a complete developmental story of LIB along with an explanation of the reasons responsible for the various technological shifts. In conclusion, this review will end with a statement of caution for the current modern battery research along with a brief discussion on beyond lithium-ion battery chemistries.

25 ENERGY STORAGE↗

Three-Dimensional Graphene–Carbon Nanotube–Ni Hierarchical Architecture as a Polysulfide Trap for Lithium–Sulfur Batteries

We report that despite their high energy density and affordable cost compared to lithium-ion (Li-ion) batteries, lithium-sulfur (Li-S) batteries still endure from slow reaction kinetics and capacity loss induced by the insulating sulfur and severe polysulfide diffusion. To address these issues, we report here nickel nanoparticles filled in vertically grown carbon nanotubes on graphene sheets (graphene-carbon nanotube-nickel composite (Gr-CNT-Ni)) that are coated onto a polypropylene separator as a polysulfide trap for the construction of high-loading sulfur cathodes. The hierarchical porous framework of Gr-CNT physically entraps and immobilizes the active material sulfur, while the strong chemical interaction with Ni nanoparticles in Gr-CNT-Ni inhibits polysulfide diffusion. The covalently interconnected electron conduction channels and carbon shell-confined metal active sites provide feasible paths for the continual regeneration of active material during the charge/discharge process. Benefitting from these novel morphological and structural features, the Li-S cell with the Gr-CNT-Ni as a polysulfide trap demonstrates high specific capacity and good cycle life. Lastly, this work provides new avenues for synergistically combining the advantages of hierarchical porous carbon architectures and metal active sites for the development of high-performance cathodes for Li-S batteries.

25 ENERGY STORAGE↗

LiCoO2 and SnO2 Thin Film Electrodes for Lithium-Ion Battery Applications

There is an increasing need for small dimension, ultra-lightweight, portable power supplies due to the miniaturization of consumer electronic devices. Rechargeable thin film lithium-ion batteries have the potential to fulfill the growing demands for micro-energy storage devices. However, rechargeable battery technology and fabrication processes have not kept paced with the advances made in device technology. Economical fabrication methods lending excellent microstructural and compositional control in the thin film battery electrodes have yet to be fully developed. In this study, spin coating has been used to demonstrate the flexibility of the approach to produce both anode (SnO2) and cathode (LiCoO2) thin films. Results on the microstructure crystal structure and electrochemical properties of the thin film electrodes are described and discussed.

Maranchi, Jeffrey P.↗

Electrochemical and Interfacial Behavior of All Solid State Batteries Using Li10SnP2S12 Solid Electrolyte

Thio-Lithium Superionic Conductor (Thio-LISICON) Li10GeP2S12 equivalent Li10SnP2S12 (LSPS) is comparable in ionic conductivity yet with a lower cost as an electrolyte for all solid-state batteries (ASSBs). ASSBs with LSPS solid electrolyte (SE), lithium-indium alloy anode, and LiCoO2 (LCO) cathode were successfully fabricated and their electrochemical performance at 60 °C was examined. Atomic layer deposition of Li3NbO4 on LCO was conducted to improve the interfacial stability. The Li3NbO4 coating significantly improves the cycle stability of the ASSB, which retains about 85% of the initial capacity after 70 cycles at a current density of 0.13 mA/cm2, while the ASSB with uncoated LCO retains ~ 60% of the initial capacity after 70 cycles. Electrochemical impedance spectroscopy tests indicate a rapid growth of charge transfer resistance upon cycling for the cell with the uncoated LCO, primarily due to the surface instability and build-up of a space charge layer between LSPS and LCO. However, the ASSBs with Li3NbO4 coated LCO show a more stable interface with a negligible impedance increase upon cycling, attributable to the buffering and passivating roles of the Li3NbO4 coating. The interfacial microstructure was analyzed to elucidate at the underlying reasons for the impedance increase and the pivotal role of the Li3NbO4 coating. Our study indicates that the surface coating significantly improves the cycle stability of the ASSBs with LSPS as the electrolyte, mostly due to an improvement of the charge transfer mechanism. The coating reduced the interphase thickness and the interfacial resistance to about a third of the uncoated one after 10 cycles.

Vinado, Carolina↗

Modulating the Surface Ligand Orientation for Stabilized Anionic Redox in Li‐Rich Oxide Cathodes

Abstract Anionic redox chemistry is emerging as a key concept in the development of high‐energy lithium‐ion batteries, as it enables a nearly doubled charge storage capacity, aiding the development of high‐capacity batteries. However, the anionic reactivity is frequently irreversible from charge to discharge, leading to rapid decay of the capacity and voltage of batteries over long‐term cycling. Although the possibility of controlling the anionic redox reactions by tuning the geometric and electronic structures has recently been proposed, the implementation of this strategy is still a critical challenge. Herein, a strategy is proposed to improve the anionic redox reversibility of a model anionic redox active cathode material, Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 , by tuning the surface ligand geometry via the growth of a lattice‐compatible spinel LiCoO 2 coating layer on the particle surface. Detailed local structure and first principles investigations reveal that the shape and orientation of the octahedral layer in the host lattice are modified. Accordingly, a two‐band oxygen redox behavior is triggered in the ligand‐orientation‐regulated Li‐rich cathode, leading to enhanced reversibility, and thus, remarkably improved capacity and voltage retention over cycling. This study highlights the importance of controllable ligand orientation, carving a new path for the development and design of Li‐rich cathodes in the future.

Liu, Yanchen↗

High Energy, Long Cycle Life Lithium-ion Batteries for PHEV Application

High-loading and high quality PSU Si anode has been optimized and fabricated. The electrochemical performance has been utilized. The PSU Si-graphite anode exhibits the mass loading of 5.8 mg/cm2, charge capacity of 850 mAh/ g and good cycling performance. This optimized electrode has been used for full-cell fabrication. The performance enhancement of Ni-rich materials can be achieved by a diversity of strategies. Higher Mn content and a small amount of Al doping can improve the electrochemical performance by suppressing interfacial side reactions with electrolytes, thus greatly benefiting the cyclability of the samples. Also, surface coatings of Li-rich materials and AlF 3 are able to improve the performance stability of Ni-rich cathodes. One kilogram of optimized concentration-gradient LiNi 0.76 Co 0.10 Mn 0.14 O 2 (CG) with careful control of composition, morphology and electrochemical performance was delivered to our collaborators. The sample achieved an initial specific capacity close to 190 mA h g -1 at C/10 rate and 180 mA h g -1 at C/3 rate as well as good cyclability in pouch full cells with a 4.4 V upper cut-off voltage at room temperature. Electrolyte additive with Si-N skeleton forms a less resistant SEI on the surface of silicon anode (from PSU) as evidenced by the evolution of the impedance at various lithiation/de-lithiation stages and the cycling data The prelithiation result demonstrates a solution processing method to achieve large area, uniform SLMP coating on well-made anode surface for the prelithiation of lithium-ion batteries. The prelithiation effect with this method is applied both in graphite half cells, graphite/NMC full cells, SiO half cells, SiO/NMC full cells, Si-Graphite half cells and Si-Graphite/NMC full cells with improvements in cycle performance and higher first cycle coulombic efficiency than their corresponding cells without SLMP prelithiation. As to the full cell fabrication and test, full pouch cells with high capacity of 2.2 Ah and 1.2 Ah have been fabricated and delivered. The cells show great uniformity and good cycling performance. The prelithiation method effectively compensate the loss in the first cycle. The cell with high energy density and long-cycle life has been achieved.

25 ENERGY STORAGE↗

Fluorination of Lithium‐Excess Transition Metal Oxide Cathode Materials

Abstract Fluorination of Li‐ion cathode materials is of significant interest as it is claimed to lead to significant improvements in long‐term reversible capacity. However, the mechanism by which LiF incorporates and improves performance remains uncertain. Indeed, recent evidence suggests that fluorine is often present as a coating layer rather than incorporated into the bulk of the material. In this work, first‐principles calculations are used to investigate the thermodynamics of fluorination in transition metal oxide cathodes to determine the conditions under which bulk fluorination is possible. It is found that unlike classic well‐ordered cathodes, which cannot incorporate fluorine, disordered rock salt‐structured materials achieve significant fluorination levels due to the presence of locally metal‐poor, lithium‐rich environments that are highly preferred for fluorine. As well as explaining the fluorination process in known materials, this finding is encouraging for the development of new disordered rock salt lithium‐excess transition metal oxides, a promising new class of Li‐ion battery cathode materials that offer superior practical capacity to traditional layered oxides. In particular, it is found that bulk fluorination may serve as an alternative source of Li‐excess in these compounds that can replace the conventional substitution of a heavy redox‐inactive element on the transition metal sublattice.

Richards, William D.↗

Protective Ceramic Coatings for Solid Oxide Fuel Cell (SOFC) Balance‐of‐Plant Components

Solid oxide fuel cells (SOFCs) have the potential to meet the growing need for electrical power generation if the cost per megawatt can be further reduced. Currently, SOFC stacks are replaced too frequently to be cost competitive. SOFC service life can be extended by preventing chromium‐ (Cr‐) bearing species from evaporating from the interior surfaces of balance of plant (BOP) components and poisoning the cathode to increase the lifetime. We have developed yttria‐stabilized zirconia (YSZ) and aluminum oxide‐ (Al 2 O 3 ‐) modified sol‐gel paints or inks for coating BOP components. 430 stainless steel (430SS) substrates with three surface conditions were coated with the 0.8–1.5 µ m thick YSZ and Al 2 O 3 paints. The coated 430SS samples were tested for thermal cycling resistance, thermal soak, and Cr evaporation. Thermal soak and thermal cycling test results show promise for the YSZ‐coated 430SS substrates. The Cr evaporation test of a coated substrate showed a 51% reduction in Cr generation, when compared with a bare substrate.

36 MATERIALS SCIENCE↗

Operation and Applications of the Boron Cathodic Arc Ion Source

The boron cathodic arc ion source has been developed with a view to several applications, particularly the problem of shallow junction doping in semiconductors. Research has included not only development and operation of the boron cathode, but other cathode materials as well. Applications have included a large deposition directed toward development of a neutron detector and another deposition for an orthopedic coating, as well as the shallow ion implantation function. Operational experience is described and information pertinent to commercial operation, extracted from these experiments, is presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Interfacial Chemistry Regulation via a Skin-Grafting Strategy Enables High-Performance Lithium-Metal Batteries

The lithium (Li) metal anode suffers severe interfacial instability from its high reactivity toward liquid electrolytes, especially carbonate-based electrolytes, resulting in poor electrochemical performance of batteries that use 4 V high-capacity cathodes. In this paper, we report a new skin-grafting strategy that stabilizes the Li metal–liquid electrolyte interface by coating the Li metal surface with poly((N-2,2-dimethyl-1,3-dioxolane-4-methyl)-5-norbornene-exo-2,3-dicarboximide), a chemically and electrochemically active polymer layer. This layer, composed of cyclic ether groups with a stiff polycyclic main chain, serves as a grafted polymer skin on the Li metal anode not only to incorporate ether-based polymeric components into the solid-electrolyte interphase (SEI) but also to accommodate Li deposition/dissolution under the skin in a dendrite/moss-free manner. Consequently, a Li-metal battery employing a Li metal anode with the grafted skin paired with LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode has a 90.0% capacity retention after 400 charge/discharge cycles and a capacity of 1.2 mAh/cm 2 in a carbonate-based electrolyte. Finally, this proof-of-concept study provides a new direction for regulating the interfacial chemistry of Li metal anodes and for enabling high-performance Li-metal batteries.

25 ENERGY STORAGE↗