Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite materials testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Summary of Gas Generation Behavior Observed in 3013 Surveillance and Monitoring Program Shelf-Life Experiments

Gas generation experiments have been conducted in small- and full-scale test containers at Los Alamos National Laboratory on samples of plutonium oxide material collected from plutonium processes across the DOE complex and tested at the bounding conditions for the Department of Energy 3013 Standard. The gas composition and pressures in the sealed experimental containers were measured over periods of months to years. These experiments have provided results for the formation and consumption of hydrogen and other gases. The conditions supporting the formation of flammable gas mixtures of hydrogen and oxygen in flammable gas mixtures were also determined. Different behaviors were observed between the materials tested based on their compositions, the stabilization performed on the material, and the post stabilization handling of the material. Many of the experiments are still ongoing. This report summarizes the results obtained for the gas generation behavior for high-purity plutonium oxides and salt-bearing impure plutonium oxides in sealed containers.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Design and Development of a Composite Dome for Experimental Characterization of Material Permeability

This paper presents the design and development of a carbon fiber reinforced plastic dome, including a description of the dome fabrication, method for sealing penetrations in the dome, and a summary of the planned test series. This dome will be used for the experimental permeability characterization and leakage validation of composite vessels pressurized using liquid hydrogen and liquid nitrogen at the Cryostat Test Facility at the NASA Marshall Space Flight Center (MSFC). The preliminary design of the dome was completed using membrane shell analysis. Due to the configuration of the test setup, the dome will experience some flexural stresses and stress concentrations in addition to membrane stresses. Also, a potential buckling condition exists for the dome due to external pressure during the leak testing of the cryostat facility lines. Thus, a finite element analysis was conducted to assess the overall strength and stability of the dome for each required test condition. Based on these results, additional plies of composite reinforcement material were applied to local regions on the dome to alleviate stress concentrations and limit deflections. The dome design includes a circular opening in the center for the installation of a polar boss, which introduces a geometric discontinuity that causes high stresses in the region near the hole. To attenuate these high stresses, a reinforcement system was designed using analytical and finite element analyses. The development of a low leakage polar boss system is also investigated.

Estrada, Hector↗

NDE of hybrid armor structures using acoustography

The US Army is investigating the use of composite materials to deliver lightweight and more effective armor protection systems to soldiers and other army assets. However, widespread use of such hybrid armor will require a reliable but fast NDE methodology to ensure integrity of these components during manufacturing and while in service. Traditional ultrasonic inspection of such hybrid armor structures may prove to be very effective, but point-by-point ultrasonic scanning is inherently time-consuming and manufacturing slowdowns could develop in high-volume production of such armor systems. In this paper, we report on the application of acoustography for the NDE of hybrid armor structures. Acoustography differs from conventional ultrasonic testing in that test objects are inspected in full field, analogously to real time x-ray imaging. The approach uses a novel, super high resolution large area acousto-optic (AO) sensor, which allows image formation through simple ultrasound shadow casting, analogous to x-ray image formation. This NDE approach offers significant inspection speed advantage over conventional point-by-point ultrasonic scanning procedures and is well-suited for high volume production. We will report initial results on a number of hybrid armor plate specimens employing composite materials that are being investigated by the US Army. Acoustography NDE results will also be verified using other complimentary NDE methods.

42 ENGINEERING↗

A comparative evaluation of in-plane shear test methods for laminated graphite-epoxy composites

The objectives were to evaluate popular shear test methods for various forms of graphite-epoxy composite materials and to determine the shear response of graphite-epoxy composites with various forms of fiber architecture. Numerical and full-field experimental stress analyses were performed on four shear test configurations for unidirectional and bidirectional graphite-epoxy laminates to assess the uniformity and purity of the shear stress (strain) fields produced in the specimen test section and to determine the material in-plane shear modulus and shear response. The test methods were the 10 deg off-axis, the +/- 45 deg tension, the Iosipescu V-notch, and a compact U-notch specimen. Specimens were prepared from AS4/3501-6 graphite-epoxy panels, instrumented with conventional strain gage rosettes and with a cross-line moire grating, and loaded in a convenient testing machine. The shear responses obtained for each test method and the two methods of specimen instrumentation were compared. In a second phase of the program the shear responses obtained from Iosipescu V-notch beam specimens were determined for woven fabric geometries of different weave and fiber architectures. Again the responses of specimens obtained from strain gage rosettes and moire interferometry were compared. Additional experiments were performed on a bidirectional cruciform specimen which was also instrumented with strain gages and a moire grating.

Morton, John↗

Friction and wear behavior of aluminum and composite airplane skins

Friction and wear behavior was determined for small skin specimens under abrasive loading conditions typical of those occurring on the underside of a transport airplane during emergency belly landing. A test apparatus consisting of a standard belt sander provided the sliding surface. Small test specimens constructed of aluminum, standard graphite-epoxy composite, aramid-epoxy composite, and toughened-resin composites were tested undar a range of pressures, belt velocities, and belt-surface textures. The effects of these test variables on the wear rate and the coefficient of friction are discussed and comparisons are made between the composite materials and aluminum. The effect of fiber orientation in the composite materials on wear rate was also investigated. In addition, tests were performed in which thermocouples were imbedded into the various test specimens to obtain temperature-time histories during abrasion.

Jackson, K. E.↗

Lunar Dust Characterization Activity at GRC

The fidelity of lunar simulants as compared to actual regolith is evaluated using Figures of Merit (FOM) which are based on four criteria: Particle Size, Particle Shape, Composition, and Density of the bulk material. In practice, equipment testing will require other information about both the physical properties (mainly of the dust fraction) and composition as a function of particle size. At Glenn Research Center (GRC) we are involved in evaluating a number of simulant properties of consequence to testing of lunar equipment in a relevant environment, in order to meet Technology Readiness Level (TRL) 6 criteria. Bulk regolith has been characterized for many decades, but surprisingly little work has been done on the dust fraction (particles less than 20 micrometers in diameter). GRC is currently addressing the information shortfall by characterizing the following physical properties: Particle Size Distribution, Adhesion, Abrasivity, Surface Energy, Magnetic Susceptibility, Tribocharging and Surface Chemistry/Reactivity. Since some of these properties are also dependent on the size of the particles we have undertaken the construction of a six stage axial cyclone particle separator to fractionate dust into discrete particle size distributions for subsequent evaluation of these properties. An introduction to this work and progress to date will be presented.

Street, Kenneth W.↗

Determine ISS Soyuz Orbital Module Ballistic Limits for Steel Projectiles Hypervelocity Impact Testing

A new orbital debris environment model (ORDEM 3.0) defines the density distribution of the debris environment in terms of the fraction of debris that are low-density (plastic), medium-density (aluminum) or high-density (steel) particles. This hypervelocity impact (HVI) program focused on assessing ballistic limits (BLs) for steel projectiles impacting the enhanced Soyuz Orbital Module (OM) micrometeoroid and orbital debris (MMOD) shield configuration. The ballistic limit was defined as the projectile size on the threshold of failure of the OM pressure shell as a function of impact speeds and angle. The enhanced OM shield configuration was first introduced with Soyuz 30S (launched in May 2012) to improve the MMOD protection of Soyuz vehicles docked to the International Space Station (ISS). This test program provides HVI data on U.S. materials similar in composition and density to the Russian materials for the enhanced Soyuz OM shield configuration of the vehicle. Data from this test program was used to update ballistic limit equations used in Soyuz OM penetration risk assessments. The objective of this hypervelocity impact test program was to determine the ballistic limit particle size for 440C stainless steel spherical projectiles on the Soyuz OM shielding at several impact conditions (velocity and angle combinations). This test report was prepared by NASA-JSC/ HVIT, upon completion of tests.

Lyons, Frankel↗

Effective Materials Property Information Management for the 21st Century

This paper discusses key principles for the development of materials property information management software systems. There are growing needs for automated materials information management in industry, research organizations and government agencies. In part these are fuelled by the demands for higher efficiency in material testing, product design and development and engineering analysis. But equally important, organizations are being driven to employ sophisticated methods and software tools for managing their mission-critical materials information by the needs for consistency, quality and traceability of data, as well as control of access to proprietary or sensitive information. Furthermore the use of increasingly sophisticated nonlinear, anisotropic and multi-scale engineering analysis approaches, particularly for composite materials, requires both processing of much larger volumes of test data for development of constitutive models and much more complex materials data input requirements for Computer-Aided Engineering (CAE) software. And finally, the globalization of engineering processes and outsourcing of design and development activities generates much greater needs for sharing a single gold source of materials information between members of global engineering teams in extended supply-chains. Fortunately material property management systems have kept pace with the growing user demands. They have evolved from hard copy archives, through simple electronic databases, to versatile data management systems that can be customized to specific user needs. The more sophisticated of these provide facilities for: (i) data management functions such as access control, version control, and quality control; (ii) a wide range of data import, export and analysis capabilities; (iii) mechanisms for ensuring that all data is traceable to its pedigree sources: details of testing programs, published sources, etc; (iv) tools for searching, reporting and viewing the data; and (v) access to the information via a wide range of interfaces, including web browsers, rich clients, programmatic access and clients embedded in third-party applications, such as CAE systems. This paper discusses the important requirements for advanced material data management systems as well as the future challenges and opportunities such as automated error checking, automated data quality assessment and characterization, identification of gaps in data, as well as functionalities and business models to keep users returning to the source: to generate user demand to fuel database growth and maintenance.

36 MATERIALS SCIENCE↗

Flexure Test For Off-Axis Unidirectional Composites

Improved flexure test yields data on ply strength of off-axis unidirectional composite material. Rotatable end supports allow ends of specimen to twist freely. End supports apply only vertical loads, making simple three-point bending test. Ply-strength data provide basis for predicting onset of damage in composite structures and serve as measure of fiber-matrix adhesion.

Crews, John H., Jr.↗

Fractographic study of epoxy fractured under mode I loading and mixed mode I/III loading

Fiber reinforced polymeric composite materials are widely used in structural components such as wind turbine blades, which are typically subject to complicated loading conditions. Thus, material response under mixed mode loading is of great significance to the reliability of these structures. Epoxy is a thermosetting polymer that is currently used in manufacturing wind turbine blades. The fracture behavior of epoxy is relevant to the mechanical integrity of the wind turbine composite materials. In this study, a novel fracture testing methodology, the spiral notch torsion test (SNTT), was applied to study the fracture behavior of an epoxy material. SNTT samples were tested using either monotonic loading or cyclic loading, while both mode I and mixed mode I/III loading conditions were used. Fractographic examination indicated the epoxy samples included in this study were prone to mode I failure even when the samples were subject to mixed mode loading. Different fatigue precracks were observed on mode I and mixed mode samples, i.e. precracks appeared as a uniform band under mode I loading, and a semi-ellipse under mixed mode loading. Fracture toughness was also estimated using quantitative fractography.

17 WIND ENERGY↗

Standard Test Methods for Textile Composites

Standard testing methods for composite laminates reinforced with continuous networks of braided, woven, or stitched fibers have been evaluated. The microstructure of these textile' composite materials differs significantly from that of tape laminates. Consequently, specimen dimensions and loading methods developed for tape type composites may not be applicable to textile composites. To this end, a series of evaluations were made comparing testing practices currently used in the composite industry. Information was gathered from a variety of sources and analyzed to establish a series of recommended test methods for textile composites. The current practices established for laminated composite materials by ASTM and the MIL-HDBK-17 Committee were considered. This document provides recommended test methods for determining both in-plane and out-of-plane properties. Specifically, test methods are suggested for: unnotched tension and compression; open and filled hole tension; open hole compression; bolt bearing; and interlaminar tension. A detailed description of the material architectures evaluated is also provided, as is a recommended instrumentation practice.

Masters, John E.↗

Progress towards waterproofing uranium nitride

Uranium mononitride (UN) is a promising, high-uranium-density fuel because of its good thermal properties and performance during irradiation and has been considered as a potential replacement for uranium(IV) oxide (UO 2 ) in commercial light water reactors. Despite these advantages, limitations are observed when the coolant comes in contact with the fuel, e.g. breach of cladding, resulting in degradation of the fuel. Research focused on continuing work from FY18 that examined the feasibility of UN-UO 2 composites for UN waterproofing purposes. Steam oxidation testing of candidate waterproofing additive materials was performed to evaluate the corrosion resistance of these materials. Composite pellets were also pressed and heated to examine chemical compatibility with UN.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Novel Composite Materials for SOFC Cathode-Interconnect Contact

This report summarized the research efforts and major conclusions of our University Coal Research Project, which focused on developing a new class of electrically-conductive, Cr-blocking, damage-tolerant Ag-perovksite composite materials for the cathode-interconnect contact of intermediate-temperature solid oxide fuel cell (SOFC) stacks. The Ag evaporation rate increased linearly with air flow rate initially and became constant for the air flow rate {ge} {approx} 1.0 cm {center_dot} s{sup -1}. An activation energy of 280 KJ.mol{sup -1} was obtained for Ag evaporation in both air and Ar+5%H{sub 2}+3%H{sub 2}O. The exposure environment had no measurable influence on the Ag evaporation rate as well as its dependence on the gas flow rate, while different surface morphological features were developed after thermal exposure in the oxidizing and reducing environments. Pure Ag is too volatile at the SOFC operating temperature and its evaporation rate needs to be reduced to facilitate its application as the cathode-interconnect contact. Based on extensive evaporation testing, it was found that none of the alloying additions reduced the evaporation rate of Ag over the long-term exposure, except the noble metals Au, Pt, and Pd; however, these noble elements are too expensive to justify their practical use in contact materials. Furthermore, the addition of La{sub 0.8}Sr{sub 0.2}MnO{sub 3} (LSM) into Ag to form a composite material also did not significantly modify the Ag evaporation rate. The Ag-perovskite composites with the perovskite being either (La{sub 0.6}Sr{sub 0.4})(Co{sub 0.8}Fe{sub 0.2})O{sub 3} (LSCF) or LSM were systematically evaluated as the contact material between the ferritic interconnect alloy Crofer 22 APU and the LSM cathode. The area specific resistances (ASRs) of the test specimens were shown to be highly dependent on the volume percentage and the type of the perovskite present in the composite contact material as well as the amount of thermal cycling that the specimens were subjected to during testing. The Ag-LSCF composite contact materials proved more effective in trapping Cr within the contact material and preventing Cr migration into the cathode than the Ag-LSM composites. Ag-perovskite composite contact materials are promising candidates for use in intermediate-temperature SOFC stacks with ferritic stainless steel interconnects due to their ability to maintain acceptably low ASRs while reducing Cr migration into the cathode material.

01 COAL, LIGNITE, AND PEAT↗

Hybrid Gear Preliminary Results-Application of Composites to Dynamic Mechanical Components

Composite spur gears were fabricated and then tested at NASA Glenn Research Center. The composite material served as the web of the gear between the gear teeth and a metallic hub for mounting to the torque-applying shaft. The composite web was bonded only to the inner and outer hexagonal features that were machined from an initially all-metallic aerospace quality spur gear. The Hybrid Gear was tested against an all-steel gear and against a mating Hybrid Gear. As a result of the composite to metal fabrication process used, the concentricity of the gears were reduced from their initial high-precision value. Regardless of the concentricity error, the hybrid gears operated successfully for over 300 million cycles at 10000 rpm and 490 in.*lbs torque. Although the design was not optimized for weight, the composite gears were found to be 20% lighter than the all-steel gears. Free vibration modes and vibration/noise tests were also conduct to compare the vibration and damping characteristic of the Hybrid Gear to all-steel gears. The initial results indicate that this type of hybrid design may have a dramatic effect on drive system weight without sacrificing strength.

Handschuh, Robert F.↗

Evaluation of Composite Airframe Dynamic Impact Modeling Using Hawker 4000 Fuselage Drop Test Data

Two drop tests of partial Hawker 4000 fuselage sections were conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to characterize the response of representative composite aerospace structure to dynamic impact loads. Test conditions were selected to induce damage into the composite structure in order to study material failure within a composite fuselage and evaluate the capability of finite element (FE) model analysis to predict that failure. The tests were simulated using FE models which were generated to isolate the effect of developmental data availability on predictive capability. FE Models of the tested fuselage sections were generated using two limited data sets. The first model configuration was reverse engineered from the test article with no information related to design or fabrication details which would be known only by the manufacturer. The second model was generated from data provided by the manufacturer but without additional material characterization test data. Models were developed using these methodologies for both fuselage sections tested. Correlation of each model to the tests conducted was evaluated in terms of damage, deformation, and cabin acceleration measurements. Correlation between the developed models and the tested fuselage sections showed that the reverse engineered model predicted the composite damage and cabin acceleration measured during test though it was limited due to lack of detail in the composite layup changes through the structure. The model developed using manufacturer specifications did not predict damage, due to limited material and component model characterization data, but it did predict acceleration on par with the reverse engineered model. Model capability and limitation sources identified were verified through correlation of a final model which was developed by combining the individual data sets. The combined model demonstrated that the addition of calibrated composite material models to accurate composite layup definitions and detailed geometry led to improved correlation of damage and acceleration response within the composite fuselage structures.

Crashworthiness↗

Evaluation of Composite Airframe Dynamic Impact Modeling Using Hawker 4000 Fuselage Drop Test Data

Two drop tests of partial Hawker 4000 fuselage sections were conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to characterize the response of representative composite aerospace structure to dynamic impact loads. Test conditions were selected to induce damage into the composite structure in order to study material failure within a composite fuselage and evaluate the capability of finite element (FE) model analysis to predict that failure. The tests were simulated using FE models which were generated to isolate the effect of developmental data availability on predictive capability. FE Models of the tested fuselage sections were generated using two limited data sets. The first model configuration was reverse engineered from the test article with no information related to design or fabrication details which would be known only by the manufacturer. The second model was generated from data provided by the manufacturer but without additional material characterization test data. Models were developed using these methodologies for both fuselage sections tested. Correlation of each model to the tests conducted was evaluated in terms of damage, deformation, and cabin acceleration measurements. Correlation between the developed models and the tested fuselage sections showed that the reverse engineered model predicted the composite damage and cabin acceleration measured during test though it was limited due to lack of detail in the composite layup changes through the structure. The model developed using manufacturer specifications did not predict damage, due to limited material and component model characterization data, but it did predict acceleration on par with the reverse engineered model. Model capability and limitation sources identified were verified through correlation of a final model which was developed by combining the individual data sets. The combined model demonstrated that the addition of calibrated composite material models to accurate composite layup definitions and detailed geometry led to improved correlation of damage and acceleration response within the composite fuselage structures.

Crashworthiness↗

Advanced composite vertical fin for L-1011 aircraft

The structural box of the L-1011 vertical fin was redesigned using advanced composite materials. The box was fabricated and ground tested to verify the structural integrity. This report summarizes the complete program starting with the design and analysis and proceeds through the process development ancillary test program production readiness verification testing, fabrication of the full-scale fin boxes and the full-scale ground testing. The program showed that advanced composites can economically and effectively be used in the design and fabrication of medium primary structures for commercial aircraft. Static-strength variability was demonstrated to be comparable to metal structures and the long term durability of advanced composite components was demonstrated.

Jackson, A. C.↗

High plasticity in refractory composite fabrication by ultrasonic additive manufacturing

Refractory metal composites are desirable for use in extreme environments that require materials with high specific strengths and resilience to external environments such as that found in nuclear and aerospace. However, due to the high melting temperature of refractories, liquid state joining processes such as welding remains difficult. Ultrasonic additive manufacturing (UAM) provides a potential route for processing refractory composites because it is a solid-state (i.e., no-melting) process and allows for intermittent machining operations to be performed between welds. Further, to demonstrate refractory composite fabrication, this study utilized UAM to machine a cavity to locate and sequester a Mo foil in a Zircaloy-4 (Zry-4) baseplate and additively build over the top with Zry-4 foils, thereby embedding the Mo in Zry-4 matrix. Significant deformation of the Zry-4 microstructure was observed: this deformation caused adiabatic heating and subsequent dynamic recrystallization through the transformation from α→β and then back to α as the material cooled. Flexural testing of the Zr–Mo composite revealed no delamination or failure, but the strength was not as expected, falling lower than a cold-worked Zry-4 sample. Finite element analysis supported that some bonding must have existed between the Zry-4 and Mo. There was indeed an interdiffusion zone at the Zry-4 foil–Mo foil interface, observing a metastable body-centered cubic β-Zr lathe. It was determined that sufficient strain energy was present to encourage the nucleation of the β-Zr grain along α-Zr grains. Future work is warranted to investigate UAM for refractory composite fabrication.

36 MATERIALS SCIENCE↗