Search NASA⌕ Search

SEARCH · Search NASA

Results for “data analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Environmentally induced discharges on satellites

The problem of assessing hazards to geosynchronous satellite systems from geomagnetic substorm encounters is investigated. The available space flight data, coupled with analytical modeling studies, show that only relatively low differential charging is possible from environmental encounters. Using an analytical study of a discharge event on SCATHA, a discharge process is postulated where a small amount of charge is lost to space. These characteristics could then be used as inputs to a coupling model to determine the hazard to a spacecraft. The procedure is applied to a three axis stabilized satellite design.

Stevens, N. J.↗
NASA NTRS1983

Some dynamical design considerations for momentum biased spacecraft

This paper discusses some of the dynamical aspects that affect the attitude behavior of a spacecraft placed in a near earth polar orbit. The parameters such as atmospheric density variation, super-rotation of upper atmosphere, pitch equilibrium angle, and trim boom length selection to reduce pitch axis drift are considered. These parameters are studied with reference to two momentum biased satellities (Magsat and Dynamics Explorer-2) and the analyses are correlated with observed flight data. It is found that the design model of certain parameters has to be improved by including other phenomena so that flight data and the analytical model predictions have good correlations. The effects of mass imbalance on the orbital and nutational modes of the spacecraft attitude are discussed.

Sellappan, R. G.↗
NASA NTRS1983

Input filter compensation for switching regulators

A novel input filter compensation scheme for a buck regulator that eliminates the interaction between the input filter output impedance and the regulator control loop is presented. The scheme is implemented using a feedforward loop that senses the input filter state variables and uses this information to modulate the duty cycle signal. The feedforward design process presented is seen to be straightforward and the feedforward easy to implement. Extensive experimental data supported by analytical results show that significant performance improvement is achieved with the use of feedforward in the following performance categories: loop stability, audiosusceptibility, output impedance and transient response. The use of feedforward results in isolating the switching regulator from its power source thus eliminating all interaction between the regulator and equipment upstream. In addition the use of feedforward removes some of the input filter design constraints and makes the input filter design process simpler thus making it possible to optimize the input filter. The concept of feedforward compensation can also be extended to other types of switching regulators.

Kelkar, S. S.↗
NASA NTRS1983

Statistical modeling of space shuttle environmental data

Statistical models which use a class of bivariate gamma distribution are examined. Topics discussed include: (1) the ratio of positively correlated gamma varieties; (2) a method to determine if unequal shape parameters are necessary in bivariate gamma distribution; (3) differential equations for modal location of a family of bivariate gamma distribution; and (4) analysis of some wind gust data using the analytical results developed for modeling application.

Tubbs, J. D.↗
NASA NTRS1985

Shuttle Communications and Tracking Systems Modeling and TDRSS Link Simulations Studies

An analytical simulation package (LinCsim) which allows the analytical verification of data transmission performance through TDRSS satellites was modified. The work involved the modeling of the user transponder, TDRS, TDRS ground terminal, and link dynamics for forward and return links based on the TDRSS performance specifications (4) and the critical design reviews. The scope of this effort has recently been expanded to include the effects of radio frequency interference (RFI) on the bit error rate (BER) performance of the S-band return links. The RFI environment and the modified TDRSS satellite and ground station hardware are being modeled in accordance with their description in the applicable documents.

Chie, C. M.↗
NASA NTRS1984

Orbiter middeck/payload standard interfaces control document

The interfaces which shall be provided by the baseline shuttle mid-deck for payload use within the mid-deck area are defined, as well as all constraints which shall be observed by all the users of the defined interfaces. Commonality was established with respect to analytical approaches, analytical models, technical data and definitions for integrated analyses by all the interfacing parties. Any payload interfaces that are out of scope with the standard interfaces defined shall be defined in a Payload Unique Interface Control Document (ICD) for a given payload. Each Payload Unique ICD will have comparable paragraphs to this ICD and will have a corresponding notation of A, for applicable; N/A, for not applicable; N, for note added for explanation; and E, for exception. On any flight, the STS reserves the right to assign locations to both payloads mounted on an adapter plate(s) and payloads stored within standard lockers. Specific locations requests and/or requirements exceeding standard mid-deck payload requirements may result in a reduction in manifesting opportunities.

Source record↗
NASA NTRS1985

Heat Flux Sensor Calibrator

The heat flux to space shuttle main engine (SSME) turbopump turbine blades may be as high as 10 to the 7th power. The heat flux causes thermal transients that are of the order of 1 sec as temperature varies from perhaps 1500 K to 100 K. It is suspected that these transients cause durability problems in the turbine blades. To quantitatively evaluate the effect of these transients, heat flux sensors or gauges were developed to obtain data to verify analytical models. The objective is to design and fabricate a system for steady state and transient calibration and durability testing of heat flux sensors for use in SSME turbine blades. The calibrator consists of: (1) the arc lamp, (2) a high speed positioning table for placing standard and special heat flux sensors in the incident beam of radiant heat flux, (3) provision for cooling the blade and special sensors inserted in the blade, (4) a computer for controlling the positioning table, storing electrical output values from sensors, and calculating heat flux from these values, and (5) a pyrometer for measuring sensor surface temperatures.

Liebert, C. H.↗
NASA NTRS1984

Heating the sun's lower transition region with fine-scale electric currents

Analytical and observational data are presented to show that the lower transition zone, a 100 km thick region at 10,000-200,000 K between the solar chromosphere and corona, is heated by local electric currents. The study was spurred by correlations between the enhanced atmospheric heating and magnetospheric flux in the chromospheric network and active regions. Field aligned current heated flux loops are asserted to mainly reside in and make up most of the transition region. It is shown that thermal conduction from the sides of hot gas columns generated by the current dissipation is the source of the observed temperature distribution in the transition regions.

Rabin, D.↗
NASA NTRS1985

Rocket thrust chamber thermal barrier coatings

A research program was conducted to generate data and develop analytical techniques to predict the performance and reliability of ceramic thermal barrier coatings in high heat flux environments. A finite element model was used to analyze the thermomechanical behavior of coating systems in rocket thrust chambers. Candidate coating systems (using a copper substrate, NiCrAlY bond coat and ZrO2.8Y2O3 ceramic overcoat) were selected for detailed study based on photomicrographic evaluations of experimental test specimens. The effects of plasma spray application parameters on the material properties of these coatings were measured and the effects on coating performance evaluated using the finite element model. Coating design curves which define acceptable operating envelopes for seleted coating systems were constructed based on temperature and strain limitations. Spray gun power levels was found to have the most significant effect on coating structure. Three coating systems were selected for study using different power levels. Thermal conductivity, strain tolerance, density, and residual stress were measured for these coatings. Analyses indicated that extremely thin coatings ( 0.02 mm) are required to accommodate the high heat flux of a rocket thrust chamber and ensure structural integrity.

Batakis, A. P.↗
NASA NTRS1986

Development of the Lens Antenna Deployment Demonstration (LADD) shuttle-attached flight experiment

The primary objective of the LADD Program is to develop a technology demonstration test article that can be used for both ground and flight tests to demonstrate the structural and mechanical feasibility and reliability of the single-axis roll-out space based radar (SBR) approach. As designed, the LADD will essentially be a generic strucutural experiment which incorporates all critical technology elements of the operational satellite and is applicable to a number of future antenna systems. However, to fully determine its design integrity for meeting the lens flatness and constant geometry requirements in a zero g environment under extreme thermal conditions, the LADD must be space flight tested. By accurately surveying the structure under varying conditions the membrane tolerance-holding capabilities of the structure will be demonstrated. The flight test will provide data to verify analytical tools used to predict thermal and structural behavior. Most important, the experiment will provide an initial indication of structural damping in a zero g vacuum environment. The recently completed Solar Array Flight Experiment (SAFE) showed orbital damping greater than that experienced during ground testing. From the experience and the information obtained from LADD it is hoped that designs can be confidently extrapolated to operational satellites with apertures in the 20 m by 60 m size range.

Hill, H.↗
NASA NTRS1987

Determination of surface shear stress with the naphthalene sublimation technique

Aeolian entrainment and transport are functions of surface shear stress and particle characteristics. Measuring surface shear stress is difficult, however, where logarithmic wind profiles are not found, such as regions around large roughness elements. An outline of a method whereby shear stress can be mapped on the surface around an object is presented. The technique involves the sublimation of naphthalene (C10H8) which is a function of surface shear stress and surface temperature. This technique is based on the assumption that the transfer of momentum, heat and mass are analogous (Reynolds analogy). If the Reynolds analogy can be shown to be correct for a given situation, then knowledge of the diffusion of one property allows the determination of the others. The analytical framework and data acquisition for the method are described. The technique was tested in the Planetary Geology Wind Tunnel. Results show that the naphthalene sublimation technique is a reasonably accurate method for determining shear stress, particularly around objects where numerous point values are needed.

Lee, J. A.↗
NASA NTRS1987

The control networks of the satellites of Jupiter

Geodetic control networks are being computed photogrammetrically for the large satellites of Jupiter, using pictures from the Voyager 1 and 2 encounters. Control points have been identified on the satellites and their coordinates computed by single-block analytical triangulation. The data sets have been converted from the B1950 to the J2000 inertial coordinate system to be compatible with future flight missions.

Davies, Merton E.↗
NASA NTRS1987

Detection of faults and software reliability analysis

Multi-version or N-version programming is proposed as a method of providing fault tolerance in software. The approach requires the separate, independent preparation of multiple versions of a piece of software for some application. These versions are executed in parallel in the application environment; each receives identical inputs and each produces its version of the required outputs. The outputs are collected by a voter and, in principle, they should all be the same. In practice there may be some disagreement. If this occurs, the results of the majority are taken to be the correct output, and that is the output used by the system. A total of 27 programs were produced. Each of these programs was then subjected to one million randomly-generated test cases. The experiment yielded a number of programs containing faults that are useful for general studies of software reliability as well as studies of N-version programming. Fault tolerance through data diversity and analytic models of comparison testing are discussed.

Knight, John C.↗
NASA NTRS1988

Reduced gravity boiling and condensing experiments simulated with the COBRA/TRAC computer code

A series of reduced-gravity two-phase flow experiments has been conducted with a boiler/condenser apparatus in the NASA KC-135 aircraft in order to obtain basic thermal-hydraulic data applicable to analytical design tools. Several test points from the KC-135 tests were selected for simulation by means of the COBRA/TRAC two-fluid, three-field thermal-hydraulic computer code; the points were chosen for a 25-90 percent void-fraction range. The possible causes for the lack of agreement noted between simulations and experiments are explored, with attention to the physical characteristics of two-phase flow in one-G and near-zero-G conditions.

Cuta, Judith M.↗
NASA NTRS1989

Modeling of transient heat pipe operation

Mathematical models and an associated computer program for heat pipe startup from the frozen state have been developed. Finite element formulations of the governing equations are written for each heat pipe region for each operating condition during startup from the frozen state. The various models were checked against analytical and experimental data available in the literature for three specific types of operation. Computations using the methods developed were made for a space shuttle reentry mission where a heat pipe cooled leading edge was used on the wing.

Colwell, Gene T.↗
NASA NTRS1990

Vibration transmission through rolling element bearings in geared rotor systems

A new mathematical model is proposed to examine the vibration transmission through rolling element bearings in geared rotor systems. Current bearing models, based on either ideal boundary conditions for the shaft or purely translational stiffness element description, cannot explain how the vibratory motion may be transmitted from the rotating shaft to the casing. Experimental results have shown that the casing plate motion is primarily flexural. Here, this issue is clarified qualitatively and quantitatively by developing a comprehensive bearing stiffness matrix of dimension 6 to model precision rolling element bearings using basic principles. The proposed bearing stiffness matrix is partially verified using available analytical and experimental data, and is completely characterized. The study extends the proposed bearing formulation to analyze the overall geared rotor system dynamics including casing and mounts. The bearing stiffness matrix is included in discrete system models using lumped parameter and/or dynamic finite element techniques.

Singh, Rajendra↗
NASA NTRS1991

FD-TD calculation with composite materials. Application to C160 aircraft measurements

In a frequency domain in which a material thickness is smaller than the skin depth, a formalism based on the sheet impedance concept was developed and introduced in the FD-TD (finite difference-time domain) code ALICE. The predictive capabilities of the 3D code was evaluated by comparison to analytical and experimental data. The following subject areas are covered: low frequency electromagnetic penetration of loaded apertures; FD-TD modeling; and in-flight experiment modeling.

Alliot, J. C.↗