Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation densities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Defect reduction in epitaxial GaSb grown on nanopatterned GaAs substrates using full wafer block copolymer lithography

Defect reduction in the large lattice mismatched system of GaSb on GaAs, {approx}7%, was accomplished using full wafer block copolymer (BCP) lithography. A self-assembled BCP mask layer was used to generate a hexagonal pattern of {approx}20 nm holes on {approx}40 nm centers in a 20 nm SiO{sub 2} layer. GaSb growth initially takes place selectively within these holes leading to a dense array of small, strain-relaxed epitaxial GaSb islands. The GaSb grown on the patterned SiO{sub 2} layer exhibits a reduction in the x-ray linewidth attributed to a decrease in the threading dislocation density when compared to blanket pseudomorphic film growth.

36 MATERIALS SCIENCE↗

Effect of buffer layer growth temperature on epitaxial GaN films deposited by magnetron sputtering

Epitaxial GaN films were deposited by reactive sputtering of a GaAs target in 100 % nitrogen at 700 deg. C on ZnO buffer layers grown at different substrate temperatures over sapphire substrates. High resolution X-ray diffraction measurements and the corresponding analysis show that the growth temperature of buffer layers significantly affects the micro-structural parameters of GaN epilayer, such as lateral coherence length, tilt and twist, while the vertical coherence length remains unaffected. The optimum substrate temperature for buffer layer growth has been found to be 300 deg. C. High epitaxial quality GaN film grown on such a buffer layer exhibited micro strain of 1.8x10{sup -4} along with screw and edge type dislocation densities of 7.87x10{sup 9} and 1.16x10{sup 11}, respectively.

36 MATERIALS SCIENCE↗

Intensity Distribution of the Three-Wave Diffraction from Dislocation Epitaxial Layers in the Reciprocal Space

The three-wave X-ray diffraction in strongly disordered epitaxial layers of GaN and ZnO is experimentally investigated. The charts of the intensity distribution in the reciprocal space are plotted in coordinates q{sub θ} and q{sub ϕ} for the most intensive three-wave combination (1010)/(1011) by means of subsequent θ- and ϕ-scanning. A nontrivial shape of the θ-sections of these contours at a distance from the ϕ center of reflection is revealed; it is different for different samples. For the θ-curves at the center of reflection, we observed a common peak that may be approximated by the Voigt function with a power-low decrease in the intensity at the wings; the decrease law (from–4.5 to–5.0) is found to be considerably greater than that for the similar curves of two-wave diffraction and not depending on the dislocation density and distribution in layers. In some films we observed a coarse-block structure; in addition, it follows from the distribution in the reciprocal space that these blocks are turned with respect to each other around a normal to the surface, which allows us to suggest the existence of low-angle boundaries between them, consisting exclusively of edge dislocations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Interband cascade light-emitting diodes grown on silicon substrates using GaSb buffer layer

Interband cascade light-emitting diodes (ICLEDs) offer attractive advantages for infrared applications, which would greatly expand if high-quality growth on silicon substrates could be achieved. Here, this work describes the formation of threading dislocations in ICLEDs grown monolithically on GaSb-on-Silicon wafers. The epitaxial growth is done in two stages: the GaSb-on-Silicon buffer is grown first, followed by the ICLED growth. The buffer growth involves the nucleation of a 10-nm-thick AlSb buffer layer on the silicon surface, followed by the GaSb growth. The AlSb nucleation layer promotes the formation of 90° and 60° interfacial misfit dislocations, resulting in a highly planar morphology for subsequent GaSb growth that is almost 100% relaxed. The resulting GaSb buffer for growth of the ICLED has a threading dislocation density of ~10 7 /cm 2 after ~3 μm of growth. The fabricated LEDs showed variations in device performance, with some devices demonstrating comparable light–current–voltage curves to those for devices grown on GaSb substrates, while other devices showed somewhat reduced relative performance. Cross-sectional transmission electron microscopy observations of the inferior diodes indicated that the multiplication of threading dislocations in the active region had most likely caused the increased leakage current and lower output power. Enhanced defect filter layers on the GaSb/Si substrates should provide more consistent diode performance and a viable future growth approach for antimonide-based ICLEDs and other infrared devices.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Phase-Specific Elastic/Plastic Interface Interactions in Layered Cr-NiAl Structures

The depth-dependent, as-grown and deformation-induced strain and dislocations partitioned through the interfaces in a two-phase layered NiAl-Cr(Mo) structure are directly measured at the mesoscale using 3-D X-ray microdiffraction. It is demonstrated that in the as-grown, undeformed state, neighboring submicron Cr solid solution and NiAl eutectic lamellae (doped with {approx}3% Mo) form a heterointerface with 180{sup o} rotation around a <1 1 2> pole. It is shown that the mechanical response to the indentation of a layered composite with alternating Cr(Mo)-NiAl lamellae is distinct from the response of single-phase materials. In the center of the indent, after the load is released, the NiAl lamellae are under compressive forward stresses (with the same sign as the indentation-induced compression) while Cr solid solution lamellae are under tensile back stresses (with opposite sign from the indentation load). The depth-dependent alternation of compressive/tensile residual strains in the neighboring Cr solid solution and NiAl lamellae is understood in the framework of the Mughrabi's composite model considering two types of structure elements: harder and softer regions. Under indentation, both kinds of lamellae are assumed to deform compatibly. After the load is released, residual forward stresses are formed in the harder lamellae, and back stresses are formed in the mechanically softer lamellae. Line-broadening analysis of the intensity distribution along the diffraction vector reveals a 15-times increase in dislocation density in the near-surface zone in the center of the indent. Such a large increase is typical for severe deformation.

36 MATERIALS SCIENCE↗

X-ray diffraction characterization of epitaxial CVD diamond films with natural and isotopically modified compositions

Comparative investigations of homoepitaxial diamond films with natural and modified isotopic compositions, grown by chemical vapor deposition (CVD) on type-Ib diamond substrates, are carried out using double-crystal X-ray diffractometry and topography. The lattice mismatch between the substrate and film is precisely measured. A decrease in the lattice constant on the order of (Δa/a){sub relax} ∼ (1.1–1.2) × 10{sup –4} is recorded in isotopically modified {sup 13}C (99.96%) films. The critical thicknesses of pseudomorphic diamond films is calculated. A significant increase in the dislocation density due to the elastic stress relaxation is revealed by X-ray topography.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Selective heteroepitaxy on deeply grooved substrate: A route to low cost semipolar GaN platforms of bulk quality

Semipolar GaN crystal stripes larger than 100 μm with dislocation densities below 5 × 10{sup 6} cm{sup −2} are achieved using a low cost fabrication process. An original sapphire patterning procedure is proposed, enabling selective growth of semipolar oriented GaN stripes while confining the defects to specific areas. Radiative and non-radiative crystalline defects are investigated by cathodoluminescence and can be correlated to the development of crystal microstructure during the growth process. A dislocation reduction mechanism, supported by transmission electron microscopy, is proposed. This method represents a step forward toward low-cost quasi-bulk semipolar GaN epitaxial platforms with an excellent structural quality which will allow for even more efficient III-nitride based devices.

36 MATERIALS SCIENCE↗

Seeded Growth of AlN Bulk Crystals in m- and c-orientation

Seeded growth of AlN boules was achieved on m-(1 0 1{sup -} 0) and c-(0 0 0 1{sup -}) orientations by physical vapor transport (PVT). The single crystalline m- and c-plane seeds were cut from freestanding AlN single crystals. AlN boules 12 mm in diameter and 7 mm in height were grown at source temperatures around 2280 C in N{sub 2} atmosphere at 500 Torr of total pressure. Under identical process conditions, the m- and c-plane boules exhibited the same growth rates, 150-170 {micro}m/h, and similar expansion angles, 22-27{sup o}, which indicated that the growth was controlled by the thermal profile inside the crucible rather than by crystallographic differences. X-ray rocking curve analysis and Raman spectroscopy confirmed that both m- and c-plane grown crystals possessed high crystalline quality. The dislocation density in both crystals was non-uniform and in the range 102-105 cm{sup -2}, as characterized by X-ray topography.

36 MATERIALS SCIENCE↗

Coupled nonlinear elasticity, plastic slip, twinning, and phase transformation in single crystal titanium for plate impact loading

High purity single crystal titanium (Ti) under shockwave loading in plate impact experiment is modelled and simulated, with help of the finite element. A thermodynamically consistent system of equations is formulated in the frame of large deformation to consider material anisotropy, rate dependence, and multi-physics including nonlinear elasticity, dislocation based plastic slip, deformation twinning, and phase transformation. A novel kinematics is proposed to consider phase transformation in the α twin variants and also to consider the dislocation based slip in all of components of parent material, primary twins and the ω phase. The thermodynamically consistent driving forces for plastic slip, twinning, and phase transformation are developed based upon the second law of thermodynamics. For nonlinear elasticity, the stiffness matrix is dependent on the volume fractions of all components, and the volumetric part of Cauchy stress is obtained from the nonlinear equation of state. Dislocation based plastic slip in multi-variant and multiphase heterogeneous materials is developed and interactions of dislocations among all slip modes are taken into account. A mechanism for dislocation density evolution during twinning and phase transformation is proposed. The shock loading along the [0001] and [10$\bar{1}1$ directions of single crystal high purity Ti is investigated computationally. Very good correspondence between simulation and experiment is obtained, which includes pole figures, volume fractions of components, free surface velocity, peak pressure, and phase transformation pressure. Multiple experimental phenomena are interpreted based upon the progression of dislocation slip, deformation twinning, and phase transformation. In compression with the [10$\bar{1}1$ crystal, a higher volume fraction in the primary twins but a lower secondary twin volume fraction in the [0001] crystal in experiment was observed. Finally, the higher propensity for phase transformation occurs in the [0001] crystal is reproduced. In addition to material texture, distributions of temperature, stresses, and plastic strains dependent on the impact loading directions are revealed.

36 MATERIALS SCIENCE↗

Improved electrical mobility in highly epitaxial La:BaSnO{sub 3} films on SmScO{sub 3}(110) substrates

Heteroepitaxial growth of BaSnO{sub 3} and Ba{sub 1−x}La{sub x}SnO{sub 3} (x = 7%) lanthanum doped barium stannate thin films on different perovskite single crystal (SrTiO{sub 3} (001) and SmScO{sub 3} (110)) substrates has been achieved by pulsed laser deposition under optimized deposition conditions. X-ray diffraction measurements indicate that the films on either of these substrates are relaxed due to the large mismatch and present a high degree of crystallinity with narrow rocking curves and smooth surface morphology while analytical quantification by proton induced X-ray emission confirms the stoichiometric La transfer from a polyphasic target, producing films with measured La contents above the bulk solubility limit. The films show degenerate semiconducting behavior on both substrates, with the observed room temperature resistivities, Hall mobilities, and carrier concentrations of 4.4 mΩ cm, 10.11 cm{sup 2} V{sup −1} s{sup −1}, and 1.38 × 10{sup 20} cm{sup −3} on SmScO{sub 3} and 7.8 mΩ cm, 5.8 cm{sup 2} V{sup −1} s{sup −1}, and 1.36 × 10{sup 20} cm{sup −3} on SrTiO{sub 3} ruling out any extrinsic contribution from the substrate. The superior electrical properties observed on the SmScO{sub 3} substrate are attributed to reduction in dislocation density from the lower lattice mismatch.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DLTS Study of plastically deformed copper-doped n-type germanium

Classical deep level transient spectroscopy (DLTS) and its modification are used to study the time constants of electron capture by substitutional Cu{sub s}{sup 2-} atoms and thermal electron emission from Cu{sub s}{sup 3-} atoms in plastically deformed Cu-doped n-type germanium. The activation energy E{sub {sigma}}, the electron capture cross-section, the energy E{sub 3} of the third acceptor level of Cu{sub s/3-} atoms, and the ionization entropy are determined. The lack of E{sub 3}-level broadening, the exponential capture kinetics for a filling-pulse duration of t{sub p} Less-Than-Or-Equivalent-To 1 ms, the fact that the Cu{sub s/2-/3-}-atom recombination parameters are independent of the dislocation density, and the low concentration of Cu{sub s/2-/3-} atoms in the deformed samples suggest that the DLTS spectra are due to Cu{sub s/2-/3-} atoms located outside the Read cylinders.

36 MATERIALS SCIENCE↗

The microstructure effects on irradiation response of ferritic – martensitic steels

Microstructural optimization to achieve greater mechanical strength has been one of the focuses in ferritic–martensitic steels development. However, these optimized microstructures’ effects on the radiation response are not well known. In this work, two ferritic–martensitic steels (9Cr-NbMo and 9Cr-Ta) underwent neutron irradiation in the High Flux Isotope Reactor, and their room-temperature post-irradiation tensile properties and microstructure evolutions were investigated and compared. These two steels exhibit similar pre-irradiation tensile behavior, and their yield strengths are higher than that of other ferritic–martensitic steels by about 200–250 MPa. Microstructural characterization on pre-irradiated materials reveals a smaller grain size in 9Cr-Ta (2.8 ± 0.3 μm in 9Cr-Ta versus 4.3 ± 0.5 μm in 9Cr-NbMo) but higher dislocation density and precipitate density in 9Cr-NbMo. As is common for ferritic–martensitic steels at low irradiation temperatures (less than about 0.45T m ), irradiation-induced hardening at 400 °C was observed for both alloys. Irradiation at 490 °C causes the two alloys to exhibit different tensile behavior: 9Cr-Ta softens by 208 MPa in yield stress, whereas 9Cr-NbMo maintains strength. Additionally, microstructural characterizations were performed, including precipitate growth, dislocation, and defect formation. Using the barrier hardening model for microstructure–property correlation, the softening in irradiated 9Cr-Ta is primarily attributed to the significant dislocation recovery, while the strength lost from the slight dislocation recovery in 9Cr-NbMo was compensated by the additional strength from the irradiation-induced cavities. The microstructure effect (primarily precipitate, dislocation and boundary) on the radiation response is discussed herein.

36 MATERIALS SCIENCE↗

TEM observation of the heat-affected zone in electron beam welded superalloy Inconel 713C

The paper presents results of microstructural observations and phase analysis of electron-beam-welded fusion zones in superalloy Inconel 713C using transmission electron microscopy. In the fusion zone, a 90% fraction of fine-grained {gamma}' precipitates was found, with sizes up to 30 nm. No dislocations were observed in the precipitates or at the {gamma}-{gamma}' interface. Primary, undissolved inclusions of {gamma}' were found in the heat-affected zone (HAZ). In the HAZ, a very high concentration of dislocations was found at the {gamma}-{gamma}' boundaries, as well as inside the {gamma}' particles and in the {gamma} solid solution. The increased dislocation density indicates loss of coherence of that phase and the creation of a semi-coherent boundary, and is related to dissolution of the particles and intensified diffusion through the interphase {gamma}-{gamma}' boundary. The lattice misfit coefficient {delta}a/a between the {gamma}' particles and {gamma} solution in the HAZ indicates negative values from - 0.20% to - 0.06%. The presence of semi-coherent boundaries and the negative lattice misfit coefficient leads to dislocation locking and can result in cracking in the HAZ.

36 MATERIALS SCIENCE↗

Martensite crystallography and chemistry in dual phase and fully martensitic steels

Highlights: • Lath martensite islands and bands were indexed in variations of dual-phase steels. • Detail insight was obtained by combined EBSD, APT, TEM, nano-indentation analysis. • The islands predominantly consist of one main packet with all six variants. • The bands are composed of connected domains, each largely made of one main packet. • Tempering at ~450 °C causes carbon partition to lath boundaries and dislocation cores. - Abstract: Lath martensite is important in industry because it is the key strengthening component in many advanced high strength steels. The study of crystallography and chemistry of lath martensite is extensive in the literature, however, mostly based on fully martensitic steels. In this work, lath martensite in dual phase steels is investigated with a focus on the substructure identification of the martensite islands and microstructural bands using electron backscattered diffraction, and on the influence of the accompanied tempering process during industrial coating process on the distribution of alloying elements using atom probe tomography. Unlike findings for the fully martensitic steels, no martensite islands with all 24 Kurdjumov-Sachs variants have been observed. Almost all martensite islands contain only one main packet with all six variants and minor variants from the remaining three packets of the same prior austenite grain. Similarly, the martensite bands are typically composed of connected domains originating from prior austenite grains, each containing one main packets (mostly with all variants) and few separate variants. The effect of tempering at ~450 °C (due to the industrial zinc coating process) has also been investigated. The results show a strong carbon partitioning to lath boundaries and Cottrell atmospheres at dislocation core regions due to the thermal process of coating. In contrast, auto-tempering contributes to the carbon redistribution only in a limited manner. The substitutional elements are all homogenously distributed. The phase transformation process has two effects on the material: mechanically, the earlier-formed laths are larger and softer and therefore more ductile (as revealed by nanoindentation); chemically, due to the higher dislocation density inside the later-formed laths, which are generally smaller, carbon Cottrell atmospheres are predominantly observed.

36 MATERIALS SCIENCE↗

Thermal Evolution of Internal Strain in Doped PbTe

Recent improvements in the efficiency of heat-to-electricity energy conversion in lead chalcogenide thermoelectrics involve reducing the thermal conductivity by incorporating large amounts of internal strain. The extent to which typical lead chalcogenide processing techniques (such as doping, ball milling, and densification) increase internal strain and dislocation density must be quantified to improve materials design. In this study, neutron powder diffraction is leveraged to evaluate the internal strain introduced by ball milling in doped and undoped powders. Doping with Na and/or Eu increases internal strain beyond ball milling alone, with the greatest increase from combining the two dopants. Strain recovery occurs in each powder above 400 K but can be suppressed by co-doping, indicating a strong dopant–dislocation interaction in this system. Therefore, high-temperature processing of PbTe powders should be avoided if high internal strain is desired. Low-temperature densification and/or rapid pressing techniques may be key to maintaining internal strain in the final pressed pellet. The diffraction peak asymmetry and correlated elastic softening measured in pressed PbTe pellets in past studies were not observed in the precursor powders measured here, suggesting that measurements of the Debye temperature on final pressed pellets are required to examine the influence of defect-induced elastic softening on thermal conductivity. This work provides key guidance for defect engineering to maximize internal strain and thermoelectric performance in PbTe thermoelectrics.

36 MATERIALS SCIENCE↗

Lifetime analysis of laser crystallized silicon films on glass

Only recently, the quality of liquid phase crystallized silicon directly on glass substrates made a huge leap towards the quality of multi-crystalline wafers with open circuit voltages well above 600 mV. In this paper, we investigate the material quality in order to identify the factors limiting further performance improvements. We employ photoluminescence imaging on a state of the art test structure with lifetime calibration by transient photoluminescence. The resulting lifetime map is converted into an effective diffusion length map and the origin of regions with short lifetimes is investigated with electron backscattering and transmission electron microscopy. High local dislocation densities in areas with dissociated coincidence site lattice boundaries were found to be responsible for the localised quenching of the photoluminescence signal.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of Small Preliminary Deformation on the Evolution of Elastoplastic Waves of Shock Compression in Annealed VT1-0 Titanium

The evolution of an elastoplastic waves of shock compression in VT1-0 titanium in the as-annealed state and after preliminary compression is measured. A preliminary strain of 0.6% and the related increase in the dislocation density are found to change the deformation kinetics radically and to decrease the Hugoniot elastic limit. An increase in the preliminary strain from 0.6% to 5.2% only weakly changes the Hugoniot elastic limit and the compression rate in the plastic shock wave. The measurement results are used to plot the strain rate versus the stress at the initial stage of high-rate deformation, and the experimental results are interpreted in terms of dislocation dynamics.

36 MATERIALS SCIENCE↗

GaAs Solar Cells on Nanopatterned Si Substrates

Integrating III-Vs onto Si is a promising route toward tandem photovoltaics and cost mitigation of III-V substrates. While many III-V/Si photovoltaic integration approaches have been studied, epitaxial growth on Si allows for fewer processing steps compared to other approaches. However, current epitaxial pathways utilize expensive techniques, such as thermal cycle annealing or thick buffer layers to control defect densities, undermining the low-cost goal of integrating III-Vs with Si. Here, we present single-junction GaAs solar cells grown directly on Si using selective area growth as an alternative low-cost technique to control material quality with a much thinner buffer. We demonstrate a 10.4%-efficient GaAs device grown on a V-grooved Si substrate, which achieved an antiphase domain-free III-V/Si interface and a threading dislocation density of 2 x 107 cm-2, despite the lack of a graded buffer. We compare this growth on V-grooved Si to solar cells grown on polished Si with and without a patterned silica buffer layer, which demonstrate efficiencies of 6.5% and 6.8%, respectively; the polished Si was patterned using nanoimprint lithography, which is a low-cost patterning technique compatible with III-V selective area growth. Cracking is found to be a critical challenge that hinders solar cell performance and is exacerbated by the V-grooved Si surface topography. The results in this paper provide a promising pathway toward high-efficiency, low-cost III-V/Si tandem photovoltaics.

14 SOLAR ENERGY↗