Search NASA⌕ Search

SEARCH · Search NASA

Results for “drying methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

The practice and economics of hybrid poplar biomass production for biofuels and bioproducts in the Pacific Northwest

Hybrid poplar demonstration-scale farms were managed in Oregon, Washington, Idaho, and California to establish management practices, yields, harvesting methods, and the economics of biomass production. Yield during the 2-year establishment cycle averaged 3.5 dry Mg ha –1 year –1 increasing to 11.6 Mg ha –1 year –1 in the ensuing 3-year coppice cycle. Populus deltoides (Bartram ex Marsh.) × P. maximowiczii (Henry) varieties preformed best in Oregon during the coppice cycle with the best variety producing 18.1 Mg ha –1 year –1 , while P. ×generosa (Henry) varieties maximized yields in Washington at 22.1 Mg ha –1 year –1 . P. ×canadensis (Moench) varieties excelled in Idaho and California with upper yields of 13.6 Mg ha –1 year –1 and 12.9 Mg ha –1 year –1 , respectively. Stands were cut with a single-pass harvester 2 years after planting and a second time after 3 years of coppice growth; material capacity, limited by poor ground conditions, varied between 21.7 to 31.3 green Mg h –1 . Chemical composition averaged 1.87% inorganics, 7.74% extractives, 26.90% lignin, 38.07% glucan, 13.66% xylan, 1.61% galactan, 1.14% arabinan, and 2.76% mannan. Production costs (USD) projected over a 20-year rotation of six coppice cycles were $71.81 Mg –1 in Washington, $89.91 Mg –1 in Oregon, $98.76 Mg–1 in Idaho, and 179.07 Mg–1 in California. Here, land rental, establishment, crop care, harvest, transportation, and land restoration, respectively, accounted for 23%, 5%, 19%, 30%, 17%, and 6% of total feedstock cost. Farms were successfully restored to conditions existing before poplar conversion. In the absence of fertilization, increases in soil pH and decreases in nitrate-nitrogen, zinc, iron, and organic matter were consistently noted but could not be associated with poplar production alone.

09 BIOMASS FUELS↗

An assessment of controlled source EM for monitoring subsurface CO 2 injection at the wyoming carbonSAFE geologic carbon storage site

Here we evaluate if electromagnetic (EM) geophysical methods for monitoring geologic carbon storage (GCS) efforts at the Wyoming CarbonSAFE project adjacent to the Dry Fork Station power plant near Gillette, Wyoming. This first involved acquiring both electric and magnetic fields at eleven different locations ranging in distance from immediately adjacent to 4 km from the plant. Passive EM measurements were made to provide spectral EM noise measurements generated by electricity production at the plant and to determine if useful magnetotelluric (MT) data can be successfully collected in the region. The processed data indicate that useful MT data can be collected as long as the site is located more than 2km away from the power plant as well as active roads and rail lines. Controlled source EM data were collected using three different source configurations, two of which connected to steel casings used to complete the injection wells. Comparing the EM noise measurements to the CSEM data show measurable electric and magnetic field signals at all sites. Next a series of three-dimensional (3D) numerical models were built that simulate resistivity changes caused by the proposed CO2 injection at depths ranging from 2.4 to 3.0km. These models were used to simulate various EM measurement configurations. The modeling shows that casing-source CSEM monitoring can provide sensitivity to the injected CO 2 if source electrodes are connected to the bottom of one or both of the injection wells.

58 GEOSCIENCES↗

Multiscale Mechanisms of Twisted Carbon Nanotube Yarns Probed In Situ by Soft X-rays during Tensile Loading

Piecing together carbon nanotubes (CNTs) into assemblies has so far failed to achieve the same elite strength performance metrics as individual CNTs, highlighting a critical deficiency in understanding the effects that the processing of individual nanostructures have on the performance of their derived macroscale assemblies, thereby hindering the development of a process-structure-performance map for these materials. Here, in this work, we propose a method to decouple the distribution orientation of nanoscale tortuosity and the microscale twist of CNT dry-spun yarns under applied loads via in situ soft X-ray probing at high energy (1200 eV) and low energy (280 eV), respectively. With this decoupling enabled by in situ soft X-ray scattering, we acquired a deeper understanding of the deformation mechanisms of these yarns. We found that for untreated yarns, the twist angle of collective CNT bundles at the macroscale is more sensitive to applied stress than the nanoscale alignment distribution. We also found that increasing nominal twist densities of yarns as well as increased strengthening via plasma treatments and polymer infiltration act to decrease the yarns’ sensitivity to realignment at the nanoscale and prevent failure by the slip mechanism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

KNN–NTK composite lead-free piezoelectric ceramic

A (K,Na)NbO₃-based lead-free piezoelectric ceramic was successfully densified. It exhibited an enhanced electromechanical coupling factor of kₚ=0.52, a piezoelectric constant d₃₃=252 pC/N, and a frequency constant Nₚ=3170 Hz m because of the incorporation of an elaborate secondary phase composed primarily of KTiNbO₅. The ceramic's nominal composition was 0.92K₀.₄₂Na₀.₄₄Ca₀.₀₄Li₀.₀₂Nb₀.₈₅O₃–0.047K₀.₈₅Ti₀.₈₅Nb₁.₁₅O₅–0.023BaZrO₃ –0.0017Co₃O₄–0.002Fe₂O₃–0.005ZnO, abbreviated herein as KNN–NTK composite. The KNN–NTK ceramic exhibited a dense microstructure with few microvoids which significantly degraded its piezoelectric properties. Elemental maps recorded using transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM–EDS) revealed regions of high concentrations of Co and Zn inside the NTK phase. In addition, X-ray diffraction patterns confirmed that a small portion of the NTK phase was converted into K₂(Ti,Nb,Co,Zn)₆O₁₃ or CoZnTiO₄ by a possible reaction between Co and Zn solutes and the NTK phase during a programmed sintering schedule. TEM studies also clarified a distortion around the KNN/NTK interfaces. Such an NTK phase filled voids between KNN particles, resulting in an improved chemical stability of the KNN ceramic. The manufacturing process was subsequently scaled to 100 kg per batch for granulated ceramic powder using a spray-drying technique. The properties of the KNN–NTK composite ceramic produced using the scaled-up method were confirmed to be identical to those of the ceramic prepared by conventional solid-state reaction sintering. Consequently, slight changes in the NTK phase composition and the distortion around the KNN/NTK interfaces affected the KNN–NTK composite ceramic's piezoelectric characteristics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Impact of acute temperature and air pollution exposures on adult lung function: A panel study of asthmatics

Background Individuals with respiratory conditions, such as asthma, are particularly susceptible to adverse health effects associated with higher levels of ambient air pollution and temperature. This study evaluates whether hourly levels of fine particulate matter (PM 2.5 ) and dry bulb globe temperature (DBGT) are associated with the lung function of adult participants with asthma. Methods and findings Global positioning system (GPS) location, respiratory function (measured as forced expiratory volume at 1 second (FEV 1 )), and self-reports of asthma medication usage and symptoms were collected as part of the Exposure, Location, and Lung Function (ELF) study. Hourly ambient PM 2.5 and DBGT exposures were estimated by integrating air quality and temperature public records with time-activity patterns using GPS coordinates for each participant (n = 35). The relationships between acute PM 2.5 , DBGT, rescue bronchodilator use, and lung function collected in one week periods and over two seasons (summer/winter) were analyzed by multivariate regression, using different exposure time frames. In separate models, increasing levels in PM 2.5 , but not DBGT, were associated with rescue bronchodilator use. Conversely DBGT, but not PM 2.5 , had a significant association with FEV 1 . When DBGT and PM 2.5 exposures were placed in the same model, the strongest association between cumulative PM 2.5 exposures and the use of rescue bronchodilator was identified at the 0–24 hours (OR = 1.030; 95% CI = 1.012–1.049; p-value = 0.001) and 0–48 hours (OR = 1.030; 95% CI = 1.013–1.057; p-value = 0.001) prior to lung function measure. Conversely, DBGT exposure at 0 hours (β = 3.257; SE = 0.879; p-value>0.001) and 0–6 hours (β = 2.885; SE = 0.903; p-value = 0.001) hours before a reading were associated with FEV 1 . No significant interactions between DBGT and PM 2.5 were observed for rescue bronchodilator use or FEV 1 . Conclusions Short-term increases in PM 2.5 were associated with increased rescue bronchodilator use, while DBGT was associated with higher lung function (i.e. FEV 1 ). Further studies are needed to continue to elucidate the mechanisms of acute exposure to PM 2.5 and DBGT on lung function in asthmatics.

60 APPLIED LIFE SCIENCES↗

Improving the representation of shallow cumulus convection with the simplified-higher-order-closure–mass-flux (SHOC+MF v1.0) approach

Abstract. Parameterized boundary layer turbulence and moist convection remain some of the largest sources of uncertainty in general circulation models. High-resolution climate modeling aims to reduce that uncertainty by explicitly attempting to resolve deep moist convective motions. An example of such a model is the Simple Cloud-Resolving E3SM Atmosphere Model (SCREAM) with a target global resolution of 3.25 km, allowing for a more accurate representation of complex mesoscale deep convective dynamics. Yet, small-scale planetary boundary layer turbulence and shallow convection still need to be parameterized, which in SCREAM is accomplished through the turbulent-kinetic-energy-based (TKE-based) simplified higher-order closure (SHOC) – a simplified version of the assumed-double-Gaussian-PDF (probability density function) higher-order-closure method. In this paper, we implement a stochastic-multiplume mass-flux (MF) parameterization of dry and shallow convection in SCREAM to go beyond the limitations of double-Gaussian-PDF closures and couple it to SHOC (SHOC+MF). The new parameterization implemented in a single-column model type version of SCREAM produces results for two shallow cumulus convection cases (marine and continental shallow convection) that agree well with the reference data from large-eddy simulations, thus improving the general representation of the thermodynamic quantities and their turbulent fluxes as well as cloud macrophysics in the model. Furthermore, SHOC+MF parameterization shows weak sensitivity to the vertical grid resolution and model time step.

54 ENVIRONMENTAL SCIENCES↗

Application of Phase Field Simulations to Fuel Behavior

The application of the phase filed method to simulate the formation and the stress induced re-orientation of zirconium hydride during dry storage of the spent fuel and clad assembly is discussed. The phase field technique is able to capture qualitatively the effect of external stress on the hydride orientation in Zr-H system. However, the modeling effort to-date is far from adequate and several issues remain to be addressed before the simulations can be used as a predictive tool for the behavior of the clad during long time dry storage.

elastic energy↗

Treatment of Radioactive Sludge From Waste Water Treatment for Weight and Volume Reduction with FreezeTec-Technique - 17010

At the Studsvik site in Sweden, Studsvik Nuclear AB operates a water treatment facility that treat all the waste water from the nuclear facilities at the site. The facility contains several pools for waste water treatment. The standard procedure for treating the water consist of adding FeCl{sub 3} to precipitate any particulates. Historically this waste has been mixed with concrete and grouted into barrels which will increase the volume needed for disposal in final repository. The sludge that is generated from the water treatment facility has been subject to treatment with the Freeze-Tec method where the sludge is freeze dewatered and after thawing generating a solid phase with high dry substance and a clear water phase. The radioactive particles/nuclides tend to stay in the solid phase while the water phase has very low concentration of radioactive particles. 99.9% of the Co-60 and Cs-137 activity end up in the solids and a dry solid with smaller volume and weight is obtained after treatment. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Feasibility study for detection of fuel assemblies state inside sealed dry storage casks using external gamma flux measurements - 25445

The license for the storage of spent nuclear fuel assemblies in dry casks is limited to 40 years. In Germany, a site for a final repository of spent fuel is not yet available. Therefore, this license has to be renewed for prolonged storage period. Currently, there is no experience with dry cask storage worldwide that goes beyond a period of 40 years. Beside regulatory and security aspects, there are questions concerning the long-term integrity of the spent fuel assemblies as this is of relevance for final transportation and reloading to final waste repository casks. Once the cask is filled and sealed, the knowledge about the state of the fuel assemblies is limited. This study investigates the feasibility of using external gamma flux measurements to detect the state of the spent fuel assemblies inside the cask. Monte-Carlo simulations were performed to evaluate the gamma flux distribution outside the sidewall of a cask with all intact fuel assemblies and a cask with one damaged fuel assembly, mimicking a fuel assembly with expanded rods and fuel relocation. The evaluation was performed for different location of the damaged fuel assembly and different storage times. The results of the investigation showed that the intensity and the shape of the gamma flux outside the sidewall of the cask are sufficient to identify the damaged fuel assembly, in case it is located near the inner wall of the cask. The detection of the inner damaged fuel assemblies, however, is less feasible. Due to the self-shielding of the fuel assemblies, the gamma photons which come from the inner fuel assemblies stopped within the fuel basket and assemblies materials. The gamma photons which do survive the fuel assemblies self-shielding reach the inner cask wall with not enough energy to escape the shielding of the thick cast iron wall. In general, it can be concluded that the more the damaged fuel assembly is close to the cask inner walls and that the damage is in a large scale (i.e., significant fuel relocation), the more it can be detected by external gamma flux measurements. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Woody biomass size reduction with selective material orientation

Roundwood logs from forests and energy plantations must be chipped, ground, or otherwise comminuted into small particles prior to conversion to solid or liquid biofuels. Rotary veneer followed by cross-grain shearing is demonstrated to be a novel and low energy consuming method for primary breakdown of logs into a raw material having high transport and storage density. Processing of high moisture raw logs into 2.5 – 4.2 mm particles prior to drying or conversion consumes less than 20% of the energy required for achieving similar particle size with hammer mills while producing a more uniform particle shape and size. As a result, energy savings from the proposed method may reduce the comminution cost of woody feedstocks by more than half.

09 BIOMASS FUELS↗

Carbon Nanotube Formation on Cr-Doped Ferrite Catalyst during Water Gas Shift Membrane Reaction: Mechanistic Implications and Extended Studies on Dry Gas Conversions

A nanocrystalline chromium-doped ferrite (FeCr) catalyst was shown to coproduce H2 and multiwalled carbon nanotubes (MWCNTs) during water gas shift (WGS) reaction in a H2-permselective zeolite membrane reactor (MR) at reaction pressures of ~20 bar. The FeCr catalyst was further demonstrated in the synthesis of highly crystalline and dimensionally uniform MWCNTs from a dry gas mixture of CO and CH4, which were the apparent sources for MWCNT growth in the WGS MR. In both the WGS MR and dry gas reactions, the operating temperature was 500 °C, which is significantly lower than those commonly used in MWCNT production by chemical vapor deposition (CVD) method from CO, CH4, or any other precursor gases. Extensive ex situ characterizations of the reaction products revealed that the FeCr catalyst remained in partially reduced states of Fe3+/Fe2+ and Cr6+/Cr3+ in WGS membrane reaction while further reduction of Fe2+ to Fe0 occurred in the CO/CH4 dry gas environments. The formation of the metallic Fe nanoparticles or catalyst surface dramatically improved the crystallinity and dimensional uniformity of the MWCNTs from dry gas reaction as compared to that from WGS reaction in the MR. Reaction of the CO/CH4 mixture containing 500 ppmv H2S also resulted in high-quality MWCNTs similar to those from the H2S-free feed gas, demonstrating excellent sulfur tolerance of the FeCr catalyst that is practically meaningful for utilization of biogas and cheap coal-derived syngas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Auto calibration of a cone-beam-CT

Purpose: This paper introduces a novel autocalibration method for cone-beam-CTs (CBCT) or flat-panel CTs, assuming a perfect rotation. The method is based on ellipse-fitting. Autocalibration refers to accurate recovery of the geometric alignment of a CBCT device from projection images alone, without any manual measurements. Methods: The authors use test objects containing small arbitrarily positioned radio-opaque markers. No information regarding the relative positions of the markers is used. In practice, the authors use three to eight metal ball bearings (diameter of 1 mm), e.g., positioned roughly in a vertical line such that their projection image curves on the detector preferably form large ellipses over the circular orbit. From this ellipse-to-curve mapping and also from its inversion the authors derive an explicit formula. Nonlinear optimization based on this mapping enables them to determine the six relevant parameters of the system up to the device rotation angle, which is sufficient to define the geometry of a CBCT-machine assuming a perfect rotational movement. These parameters also include out-of-plane rotations. The authors evaluate their method by simulation based on data used in two similar approaches [L. Smekal, M. Kachelriess, S. E, and K. Wa, 'Geometric misalignment and calibration in cone-beam tomography,' Med. Phys. 31(12), 3242-3266 (2004); K. Yang, A. L. C. Kwan, D. F. Miller, and J. M. Boone, 'A geometric calibration method for cone beam CT systems,' Med. Phys. 33(6), 1695-1706 (2006)]. This allows a direct comparison of accuracy. Furthermore, the authors present real-world 3D reconstructions of a dry human spine segment and an electronic device. The reconstructions were computed from projections taken with a commercial dental CBCT device having two different focus-to-detector distances that were both calibrated with their method. The authors compare their reconstruction with a reconstruction computed by the manufacturer of the CBCT device to demonstrate the achievable spatial resolution of their calibration procedure. Results: Compared to the results published in the most closely related work [K. Yang, A. L. C. Kwan, D. F. Miller, and J. M. Boone, 'A geometric calibration method for cone beam CT systems,' Med. Phys. 33(6), 1695-1706 (2006)], the simulation proved the greater accuracy of their method, as well as a lower standard deviation of roughly 1 order of magnitude. When compared to another similar approach [L. Smekal, M. Kachelriess, S. E, and K. Wa, 'Geometric misalignment and calibration in cone-beam tomography,' Med. Phys. 31(12), 3242-3266 (2004)], their results were roughly of the same order of accuracy. Their analysis revealed that the method is capable of sufficiently calibrating out-of-plane angles in cases of larger cone angles when neglecting these angles negatively affects the reconstruction. Fine details in the 3D reconstruction of the spine segment and an electronic device indicate a high geometric calibration accuracy and the capability to produce state-of-the-art reconstructions. Conclusions: The method introduced here makes no requirements on the accuracy of the test object. In contrast to many previous autocalibration methods their approach also includes out-of-plane rotations of the detector. Although assuming a perfect rotation, the method seems to be sufficiently accurate for a commercial CBCT scanner. For devices which require higher dimensional geometry models, the method could be used as a initial calibration procedure.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Highly Resolved Reference Projections of Building Energy Use for the Contiguous United States: Building Sector Energy Baselines, Projection Methods, and Results

This report describes one methodology of projecting energy consumption of the US residential and commercial building sectors using NREL's ResStock™ and ComStock™ as well as growth rates derived from EIA's Annual Energy Outlook (AEO). The impetus for this work is to provide an intermediate method for compiling demand-side sectoral energy projections that is suitable for grid-scale analysis, such as NREL's Standard Scenarios. ResStock and ComStock are physics-based and statistically representative building stock models of the US residential and commercial sector, respectively. Using the 2012 actual meteorological year (AMY) weather data, the sectoral energy baselines are simulated and then segmented along key dimensions (e.g., geography, dwelling/building type). The segmented results are then scaled using the corresponding annual growth rates derived from the 2021 AEO reference case to produce energy projections out to 2050. The compiled result is a demand-side grid model (dsgrid) data set suitable for use in NREL's large-scale grid models, such as the Regional Energy Deployment System (ReEDS). This simple projection method does not endogenously represent how the building stock could evolve through time. Most notably, it does not reflect large-scale electrification, for example, the conversion of space heating, water heating, clothes drying, and cooking from primary fossil fuels to electricity, as this is not part of AEO's reference case assumptions. Nonetheless this approach is more resolved and potentially extensible compared to the current method used by Standard Scenarios's reference case, which augments a sector's total load based on a single growth rate from AEO.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Impact of specimen preparation method on photovoltaic backsheet degradation during accelerated aging test

In this study, we highlight some important factors in the specimen preparation methods for evaluating photovoltaic backsheet properties after accelerated aging. Two different sequences are considered: Method (I) cut-then-age: cut into 1-cm wide strips and then expose to stress, and Method (II) age-then-cut: expose a larger sheet to stress and then cut into 1-cm widths for mechanical property measurements. We also compare the effect of three cutting methods, (a) tensile specimen punch, (b) paper cutter, and (c) fresh razor blade. Several commercial backsheets were evaluated, with stress exposures including (a) pressure cooker test (PCT), (b) dry ultraviolet (UV) radiation exposure, and (c) UV combined damp heat tests. Fourier transform infrared spectrometer (FTIR) and intrinsic viscosity (IV) were used to analyze the materials on unstressed materials and samples exposed to PCT. The results show that both the cutting method and the time of cutting have an impact on the backsheet mechanical properties. Additionally, under UV exposure, Method II, age-then-cut, generally resulted in a higher average value, with more variation than Method I; however, if the side strips from Method II were excluded, the variation dropped to the same level. This is because the specimens at the sides of the sheet get additional damage from UV light from the exposed sides of the sample. In contrast to UV exposure, PCT specimens prepared by Method II result in lower average values and higher variability. This is attributed to embrittlement through the bulk of the sample where the cutting of embrittled specimens appears to result in more edge defects which can then initiate a break at smaller strains. The data suggest that for UV exposures, the specimens should be cut after aging and the exposed side specimens discarded, and that for PCT exposures, the specimens should be cut before the exposure.

14 SOLAR ENERGY↗

Magnetorheological materials, method for making, and applications thereof

A magnetorheological material comprises a magnetic particle and a ceramic material, wherein the magnetorheological material is in a dried form and further wherein a portion of the ceramic material is in the form of a nanocrystalline coating over the entire exterior surface of the magnetic particle and another portion of the ceramic material is in the form of a free nanocrystal. A magnetorheological material comprises a magnetic particle having a ceramic material coating over an external surface thereof as a result of a coating process, and a free nanocrystal of the ceramic material in the form of a residual by-product of the coating process. A sol-gel process for making a magnetorheological product comprises providing a sol of a desired ceramic coating material; combining a desired quantity of carbonyl iron (CI) particles with the sol to coat the CI particles with the ceramic coating material; creating a resulting quantity of nanocrystalline ceramic material-coated CI particles and a quantity of free nanocrystals of the ceramic material; and, drying the resulting quantity of coated CI particles and free nanocrystals to a moisture content equal to or less than 2 wt %.

36 MATERIALS SCIENCE↗

Turbine and methods of assembling the same

A turbine operable with a first fluid and a second fluid is provided. The turbine includes a shaft and having a dry gas seal area, a balance area, and a shaft surface. The turbine also includes a stationary component coupled to a housing and having a first side and a second side and defining a channel in flow communication with the shaft surface. A heat exchange assembly is coupled to the housing and in flow communication with the shaft and the stationary component. The heat exchange assembly includes a first flow path coupled in flow communication with the dry gas seal area and the channel and configured to direct the first fluid along the first side. Heat exchange assembly also includes a second flow path coupled in flow communication with the balance area and channel and configured to direct the second fluid along the second side.

42 ENGINEERING↗