Search NASA⌕ Search

SEARCH · Search NASA

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Prediction of Externally Blown Flap Noise and Turbomachinery Strut Noise

Methods were developed for predicting externally blown flap (EBF) noise and turbomachinery strut noise. Noise radiated by under-the-wing and upper-surface-blowing EBF configurations is calculated as a sum of lift dipole noise, trailing edge noise, and jet quadrupole noise. Resulting predictions of amplitudes and spectra generally were in good agreement with data from small-scale models. These data cover a range of exhaust velocity, flap deflection, exhaust nozzle position, exhaust nozzle shape, and ratio of exhaust nozzle diameter to wing chord. A semi-empirical method for predicting dipole noise radiation from a strut with incident turbulence was in good agreement with data. Leading-edge regions made of perforated plate backed by a bulk acoustic absorber achieved up to 7 db reduction of strut noise caused by incident turbulence at high frequencies. Radial turbulence in a turbofan exit duct was found to have a relatively high level associated with the mean velocity defect in the rotor blade wakes. Use of these turbulence spectra and a dipole noise radiation equation gave general prediction of measured aft-radiated sound power caused by a splitter ring in a full-scale fan exit duct.

Fink, M. R.↗
NASA NTRS1975

Influence of structural damping, preconing offsets and large deflection on the flap-lag-torsional stability of a cantilevered rotor blade

A set of equations describing the coupled flap-lag-torsional dynamics of a cantilevered rotor blade in hover is presented. This set of equations is used to evaluate the influence of structural damping, preconing and offsets on the linearized aeroelastic stability of some representative blade configurations. A number of examples illustrating the coupled nonlinear flap-lag-torsional response are considered.

Friedmann, P.↗
NASA NTRS1975

Upwash angles near engine inlets of an externally blown flap STOL transport

An investigation was conducted in the Langley V/STOL tunnel to determine the upwash flow angles in the region of the nacelle inlets of a representative powered-lift transport configuration operating at high lift coefficients. The upwash angles were indicated by tufts and measured from photographs. A potential-flow program was used to estimate these flow angles. Large upflow angles exist near the inlets of the nacelles; the highest value (67.3 deg) occurred with flaps at 15, 35, 55 deg, an angle of attack of 25.7 deg, and a thrust coefficient of 4. The upflow angle was found to be strongly dependent on the circulation lift, regardless of the flap deflection, angle of attack, or thrust coefficient used to generate this circulation lift. The potential-flow calculations away from the nacelle inlets agreed fairly well with the experimental data.

Naeseth, R. L.↗
NASA NTRS1975

Aerodynamic characteristics of a powered, externally blown flap STOL transport model with two engine simulator sizes

The low-speed aerodynamic characteristics are investigated of a general research model - a swept-wing, jet-powered STOL transport with externally blown flaps. The model was tested with four-engine simulators mounted on pylons under the 9.3-percent-thick supercritical airfoil wing. Two sets of air ejectors were used to provide data with large and small engines. Tests were conducted in the Langley V/STOL tunnel over an angle-of-attack range of -4 deg to 22 deg and a thrust-coefficient range from 0 to approximately 4. The effects are described of power, wing leading-edge slat configuration, T-tail and low horizontal-tail positions, and double-slotted flap deflection. Additional untrimmed and trimmed engine-out data and tail-body data are included.

Johnson, W. G., Jr.↗
NASA NTRS1976

Reflection-plane tests of spoilers on an advanced technology wing with a large Fowler flap

Wind tunnel experiments were conducted to determine the effectiveness of spoilers applied to a finite-span wing which utilizes the GA(W)-1 airfoil section and a 30% chord full-span Fowler flap. A series of spoiler cross sectioned shapes were tested utilizing a reflection-plane model. Five-component force characteristics and hinge moment measurements were obtained. Results confirm earlier two-dimensional tests which showed that spoilers could provide large lift increments at any flap setting, and that spoiler control reversal tendencies could be eliminated by providing a vent path from lower surface to upper surface. Performance penalties due to spoiler leakage airflow were measured.

Wentz, W. H., Jr.↗
NASA NTRS1975

Hypersonic incipient separation on delta wing with trailing-edge flap

The paper reviews the experimental data on the incipient separation characteristics of planar delta wings of 75 degree sharp leading edges, with full-span trailing edge flap deflected into the windward flow. The local Reynolds number range for these investigations covered laminar, transitional and turbulent conditions. It is shown that, while turbulent boundary layer data correlates with two dimensional results, in the laminar and transitional cases, there is a nearly parallel shift to higher flap angles for incipient separation.

Rao, D. M.↗
NASA NTRS1976

Sound generated in the vicinity of the trailing edge of an upper surface blown flap

Far-field noise data indicated that for practical upper surface blown flap configurations, the noise radiated below the flap is dominated by the noise generated in the vicinity of the trailing edge. Sound field by turbulent mixing in the trailing edge wake is investigated experimentally and theoretically. Hot-wire measurements were made downstream of the trailing edge to determine the gross turbulence mixing characteristics of the flow. This information is used as input to a theoretical analysis of the sound field. Favorable agreement is found between predicted and measured far-field noise directivities at various frequencies and noise power spectra at various directions.

Tam, C. K. W.↗
NASA NTRS1975

Sensitivity of Hingeless Rotor Blade Flap-lag Stability in Hover to Analytical Modelling Assumptions

Prediction of flap-lag stability using a single bending mode for each degree-of-freedom is examined in the case in which the bending modes are assumed to be the same in the flap and lag directions and are independent of pitch angle and stiffness distribution. It is shown that this model gives results analogous to those obtained by Ormiston employing a rigid blade model with the blade and hub stiffness represented by springs in the limiting cases of the elastic coupling parameter R = 0 and 1. For intermediate values of R the results are shown to be quite different. The mode shape assumptions are shown to result in what is referred to as the parallel spring model in contrast to Ormiston's model which is referred to as a series spring model. The similarities and differences between these two models are developed in some details. The differences between these two models are examined for various typical rotor blade characteristics. Other aspects of the sensitivity of this problem are also considered.

Curtiss, H. C., Jr.↗
NASA NTRS1976

Wing surface-jet interaction characteristics of an upper-surface blown model with rectangular exhaust nozzles and a radius flap

The wing surface jet interaction characteristics of an upper surface blown transport configuration were investigated in the Langley V/STOL tunnel. Velocity profiles at the inboard engine center line were measured for several chordwise locations, and chordwise pressure distributions on the flap were obtained. The model represented a four engine arrangement having relatively high aspect ratio rectangular spread, exhaust nozzles and a simple trailing edge radius flap.

Bloom, A. M.↗
NASA NTRS1976

Delayed flap approach procedures for noise abatement and fuel conservation

The NASA/Ames Research Center is currently investigating the delayed flap approach during which pilot actions are determined and prescribed by an onboard digital computer. The onboard digital computer determines the proper timing for the deployment of the landing gear and flaps based on the existing winds and airplane gross weight. Advisory commands are displayed to the pilot. The approach is flown along the conventional ILS glide slope but is initiated at a higher airspeed and in a clean aircraft configuration that allows for low thrust and results in reduced noise and fuel consumption. Topics discussed include operational procedures, pilot acceptability of these procedures, and fuel/noise benefits resulting from flight tests and simulation.

Edwards, F. G.↗
NASA NTRS1977

Static and wind-on tests of an upper-surface-blown jet-flap nozzle arrangement for use on the Quiet Clean Short-haul Experimental Engine (QCSEE)

The internal aerodynamic performance, the static turning characteristics, and the forward-speed characteristics of two 1/12-scale upper surface-blown jet-flap exhaust-nozzle arrangements designed for use on the Quiet Clean Short-Haul Experimental Engine (QCSEE) were investigated. The nozzles were equipped with interchangeable area-control side doors in the aft sidewalls of the nozzle so that the effective nozzle area could be varied over a wide range. A simulated wing was used to evaluate installation losses for the nozzles. A smoothly curved flap was attached to the trailing edge of the simulated wing to allow an evaluation of the static turning characteristics of the nozzle arrangement. Forward-speed effects on the jet turning characteristics of the QCSEE nozzles were evaluated by mounting a single engine on a semispan wing designed to be representative of a four-engine STOL transport configuration.

Phelps, A. E., III↗
NASA NTRS1977

Aeroelastic stability of coupled flap-lag-torsional motion of helicopter rotor blades in forward flight

A set of coupled periodic nonlinear differential flap-lag-torsional equations of blade motion is described which can simulate a blade having a precone, twist, distributed torsion, root torsion, torque offset, blade-root offsets, and offsets among the elastic axis, the aerodynamic center, and the blade cross-sectional center of mass. It is noted that the aerodynamic loads derived for these equations are applicable to cases of both hover and forward flight. The aeroelastic stability of a hingeless helicopter blade is investigated by linearizing the nonlinear differential equations of motion about a time-dependent equilibrium position of the helicopter in forward flight, using propulsion and moment trim procedures. A comparison of the results with those obtained previously for coupled flap-lag-torsional boundaries in hover indicates that aeroelastic-stability margins are degraded due to forward flight.

Friedmann, P.↗
NASA NTRS1977

Nonlinear flap-lag axial equations of a rotating beam

It is possible to identify essentially four approaches by which analysts have established either the linear or nonlinear governing equations of motion for a particular problem related to the dynamics of rotating elastic bodies. The approaches include the effective applied load artifice in combination with a variational principle and the use of Newton's second law, written as D'Alembert's principle, applied to the deformed configuration. A third approach is a variational method in which nonlinear strain-displacement relations and a first-degree displacement field are used. The method introduced by Vigneron (1975) for deriving the linear flap-lag equations of a rotating beam constitutes the fourth approach. The reported investigation shows that all four approaches make use of the geometric nonlinear theory of elasticity. An alternative method for deriving the nonlinear coupled flap-lag-axial equations of motion is also discussed.

Kaza, K. R. V.↗
NASA NTRS1977

Application of powered lift and mechanical flap concepts for civil short-haul transport aircraft design

The objective of this paper is to determine various design and performance parameters, including wing loading and thrust loading requirements, for powered-lift and mechanical flap conceptual aircraft constrained by field length and community noise impact. Mission block fuel and direct operating costs (DOC) were found for optimum designs. As a baseline, the design and performance parameters were determined for the aircraft using engines without noise suppression. The constraint of the 90 EPNL noise contour being less than 2.6 sq km (1.0 sq mi) in area was then imposed. The results indicate that for both aircraft concepts the design gross weight, DOC, and required mission block fuel decreased with field length. At field lengths less than 1100 m (3600 ft) the powered lift aircraft had lower DOC and block fuel than the mechanical flap aircraft but produced higher unsuppressed noise levels. The noise goal could easily be achieved with nacelle wall treatment only and thus resulted in little or no performance or weight penalty for all studied aircraft.

Conlon, J. A.↗
NASA NTRS1977

Forward speed effects on blown flap noise

The effects of forward speed on the noise of under-the-wing (externally blown flaps, EBF) and over-the-wing (upper surface blown, USB) blown flap configurations were measured in wind tunnel model tests with cold jets. The results are presented without correction for the effects (e.g., signal convection, shear layer refraction) associated with flight simulation in a wind tunnel or free jet facility. Noise decreases were generally observed at microphones forward of the wing. The reductions were larger at the low frequencies (below peak SPL) than at the high (above peak SPL). Noise increases of 10 dB or more were observed at the aft microphones, especially in the high frequency range.

Pennock, A. P.↗
NASA NTRS1976

Wind-tunnel investigation of aerodynamic performance, steady amd vibratory loads, surface temperatures, and acoustic characteristics of a large-scale twin-engine upper-surface blown jet-flap configuration

Static and wind-on tests were conducted to determine the aerodynamic characteristics of and the effects of jet impingement on the wing of a large scale upper surface blown configuration powered with an actual turbine engine. The wing and flaps were instrumented with experimental dual-sensing transducer units consisting of a fluctuating pressure gage, a vibratory accelerometer, and a surface mounted alumel thermocouple. Noise directivity and spectral content measurements were obtained for various flap configurations and various engine thrust settings to provide baseline noise data for other upper surface blown configurations.

Source record↗
NASA NTRS1978

Effect of high lift flap systems on the conceptual design of a 1985 short-haul commercial STOL tilt rotor transport

The performances of a derivative concept of a 1985 STOL tilt rotor transport, and of a second concept having a complex mechanical flap system similar to a short field B737 aircraft were compared for a 370 kilometer (200 nautical mile) short haul mission. The flap system of the latter allowed lift to be shifted from the rotor system to the wing, permitting a 26 percent reduction in dynamic component weight, while also permitting the use of a smaller wing. The wing and disc loading of this concept were 5746 (120 psf) and 1915 (40 psf) newtons per square meter, respectively, while the wing and disc loading of the derivative concept were 4788 (100 psf) and 1197 (25 psf) newtons per square meter, respectively. The high lift wing tilt rotor showed slightly improved fuel usage over its entire operating range and about 6 to 8 percent improvement in direct operating costs, resulting from its improved cruise efficiency and reduced weight. Other advantages include improved reliability with potentially reduced maintenance and better riding quality.

Shovlin, M. D.↗
NASA NTRS1978

A flight investigation of the stability, control, and handling qualities of an augmented jet flap STOL airplane

The stability, control, and handling qualities of an augmented jet flap STOL airplane are presented. The airplane is an extensively modified de Havilland Buffalo military transport. The modified airplane has two fan-jet engines which provide vectorable thrust and compressed air for the augmentor jet flap and Boundary-Layer Control (BLC). The augmentor and BLC air is cross ducted to minimize asymmetric moments produced when one engine is inoperative. The modifications incorporated in the airplane include a Stability Augmentation System (SAS), a powered elevator, and a powered lateral control system. The test gross weight of the airplane was between 165,000 and 209,000 N (37,000 and 47,000 lb). Stability, control, and handling qualities are presented for the airspeed range of 40 to 180 knots. The lateral-directional handling qualities are considered satisfactory for the normal operating range of 65 to 160 knots airspeed when the SAS is functioning. With the SAS inoperative, poor turn coordination and spiral instability are primary deficiencies contributing to marginal handling qualities in the landing approach. The powered elevator control system enhanced the controllability in pitch, particularly in the landing flare and stall recovery.

Vomaske, R. F.↗