Search NASA⌕ Search

SEARCH · Search NASA

Results for “generalized linear model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

The dynamics and control of large flexible space structures X, part 1

The effect of delay in the control system input on the stability of a continuously acting controller which is designed without considering the delay is studied. The stability analysis of a second order plant is studied analytically and verified numerically. For this example it is found that the system becomes unstable for a delay which is equivalent to only 16 percent of its natural period of motion. It is also observed that even a small amount of natural damping in the system can increase the amount of delay that can be tolerated before the onset of instability. The delay problem is formulated in the discrete time domain and an analysis procedure suggested. The maximum principle from optimal control theory is applied to minimize the time required for the slewing of a general rigid spacecraft. The slewing motion need not be restricted to a single axis maneuver. The minimum slewing time is calculated based on a quasi-linearization algorithm for the resulting two point boundary value problem. Numerical examples based on the rigidized in-orbit model of the SCOLE also include the more general reflector line-of-sight slewing maneuvers.

Bainum, Peter M.↗

A New Forced Oscillation Capability for the Transonic Dynamics Tunnel

A new forced oscillation system has been installed and tested at NASA Langley Research Center's Transonic Dynamics Tunnel (TDT). The system is known as the Oscillating Turntable (OTT) and has been designed for the purpose of oscillating, large semispan models in pitch at frequencies up to 40 Hz to acquire high-quality unsteady pressure and loads data. Precisely controlled motions of a wind-tunnel model on the OTT can yield unsteady aerodynamic phenomena associated with flutter, limit cycle oscillations, shock dynamics, and non-linear aerodynamic effects on many vehicle configurations. This paper will discuss general design and components of the OTT and will present test data from performance testing and from research tests on two rigid semispan wind-tunnel models. The research tests were designed to challenge the OTT over a wide range of operating conditions while acquiring unsteady pressure data on a small rectangular supercritical wing and a large supersonic transport wing. These results will be presented to illustrate the performance capabilities, consistency of oscillations, and usefulness of the OTT as a research tool.

Piatak, David J.↗

Current Limitations on VLBI Accuracy

The contribution of VLBI to geophysics and geodesy arises from its ability to measure distances between stations in a network and to determine the orientation of stations in the network as well as the orientation of the network with respect to the external reference frame of extragalactic radio objects. Integrating nearly two decades of observations provides useful information about station positions and velocities and the orientation of the Earth, but the complications of the real world and the limitations of observing, modeling and analysis prevent recovery of all effects. Of the factors that limit the accuracy of seemingly straightforward geodetic parameters, the neutral propagation medium has been subject to the greatest scrutiny, but the treatment of the mapping function, the wet component and spatial/temporal inhomogeneities is still improving. These affect both the terrestrial scale and consistency over time. The modeling of non-secular site motions (tides and loading) has increased in sophistication, but there are some differences between the models and the observations. VLBI antennas are massive objects, so their behavior is quite unlike GPS monuments, but antenna deformations add some (generally) unmodeled signal. Radio sources used in geodetic VLBI observations are selected for strength and (relative) absence of structure, but apparent changes in position can leak into geodetic parameters. A linear rate of change of baseline or site parameters is the simplest model and its error improves with time span. However, in most cases the VLBI data distribution is insufficient to look for real non-linear behavior that might affect the average rate. A few sites have multiple VLBI antennas, and some show small differences in rate. VLBI intrinsically measures relative positions and velocities, but individual site positions and velocities are generally more useful. The creation of the VLBI terrestrial reference frame, which transforms relative information into individual results, is an empirical process that has intrinsic errors. While UT1 is uniquely measured by VLBI, the geographical distribution and availability of VLBI stations, especially in the southern hemisphere, and the consistency of the VLBI terrestrial reference frame may limit the accuracy of Earth orientation measurements. The effects of particular error sources on geodetic and geophysical parameters derived from VLBI data will be illustrated.

Ma, Chopo↗

Climate Fluctuations and Climate Sensitivity

Some evidence is presented that the main part of the atmospheric climate system is such that small forcings in the heat balance lead to linear responses in the surface temperature field. By examining first a noise forced energy-balance climate model and then comparing it with a long run of a highly symmetrical general circulation model, one finds a remarkable connection between spatial autocorrelation statistics and the thermal influence function for a point heat source. These findings are brought together to indicate that this particular climatological field may be largely governed by linear processes.

North, Gerald R.↗

Cyclic Oxidation Modeling and Life Prediction

The cyclic oxidation process can be described as an iterative scale growth and spallation sequence by a number of similar models. Model input variable include oxide scale type and growth parameters, spalling geometry, spall constant, and cycle duration. Outputs include net weight change, the amounts of retained and spalled oxide, the total oxygen and metal consumed, and the terminal rates of weight loss and metal consumption. All models and their variations produce a number of similar characteristic features. In general, spalling and material consumption increase to a steady state rate, at which point the retained scale approaches a constant and the rate of weight loss becomes linear. For one model, this regularity was demonstrated as dimensionless, universal expressions, obtained by normalizing the variables by critical performance factors. These insights were enabled through the use of the COSP for Windows cyclic oxidation spalling program.

Smialek, James L.↗

Rift systems on Venus: An assessment of mechanical and thermal models

The formation and distribution of major tectonic features on Venus are closely linked to the dominant mechanism of lithospheric heat loss. Among the most spectacular and extensive of the major tectonic features on Venus are the Chasmata, deep linear valleys generally interpreted to be the products of lithospheric extension and rifting. Systems of chasmata and related features can be traced along several tectonic zones up to 20,000 km in linear extent. Mechanical and thermal models for terrestrial continental-rifting are applied to the rift systems of Venus. The models are tested against known topographic and tectonic characteristics of Venus chasmata as well as independent information on the physical properties of the Venus crust and lithosphere.

Solomon, S. C.↗

Bayesian Optimization Framework for Imperfect Data or Models

Conventional Bayesian optimization methods implicitly assume that the data and model being optimized are “perfect.” This assumption leads to inaccurate posterior probability distribution functions (PDFs) when applied to “imperfect” data or models. The new Bayesian optimization framework presented in this report provides a way to parameterize the effect of imperfections usually encountered in a prior PDF of generalized data or a model on the posterior PDF. The effects of imperfections are parameterized by a set of constraints imposed on the posterior expectation values of deviations between the data and the model and on their covariance matrix elements. A particular set of values for these constraints conveys an evaluator’s best estimate of the effect of imperfections on the corresponding posterior expectation values. When a prior PDF of generalized data is assumed to be normal, an expression for a posterior PDF satisfying an arbitrary set of constraints is derived analytically for linear models. An analogous iterative algorithm is given for nonlinear models. The corresponding posterior PDF should be used to estimate any posterior expectation values in the presence of imperfections parameterized by that set of constraints. A posterior PDF of a conventional Bayesian optimization method is recovered analytically when all evaluator-specified constraints are set to zero (i.e., in the absence of any imperfections). The analytical expressions derived in this report for normal PDFs and linear models were verified numerically by a Metropolis–Hastings Monte Carlo method. The methods presented herein could be applied to any kind of data or models, including differential cross-section data or integral benchmark experiments.

97 MATHEMATICS AND COMPUTING↗

Effects of Hall current and electron temperature anisotropy on proton fire-hose instabilities

The standard magnetohydrodynamic (MHD) theory predicts that the Alfvén wave may become fire-hose unstable for β{sub ∥}−β{sub ⊥}>2. In this study, we examine the proton fire-hose instability (FHI) based on the gyrotropic two-fluid model, which incorporates the ion inertial effects arising from the Hall current and electron temperature anisotropy but neglects the electron inertia in the generalized Ohm's law. The linear dispersion relation is derived and analyzed which in the long wavelength approximation, λ{sub i}k→0 or α{sub e}=μ{sub 0}(p{sub ∥,e}−p{sub ⊥,e})/B{sup 2}=1, recovers the ideal MHD model with separate temperature for ions and electrons. Here, λ{sub i} is the ion inertial length and k is the wave number. For parallel propagation, both ion cyclotron and whistler waves become propagating and growing for β{sub ∥}−β{sub ⊥}>2+λ{sub i}{sup 2}k{sup 2}(α{sub e}−1){sup 2}/2. For oblique propagation, the necessary condition for FHI remains to be β{sub ∥}−β{sub ⊥}>2 and there exist one or two unstable fire-hose modes, which can be propagating and growing or purely growing. For large λ{sub i}k values, there exists no nearly parallel FHI leaving only oblique FHI and the effect of α{sub e}>1 may greatly enhance the growth rate of parallel and oblique FHI. The magnetic field polarization of FHI may be reversed due to the sign change associated with (α{sub e}−1) and the purely growing FHI may possess linear polarization while the propagating and growing FHI may possess right-handed or left-handed polarization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Instability of the Ackerman-Carroll-Wise model, and problems with massive vectors during inflation

We prove that the anisotropic inflationary background of the Ackerman-Carroll-Wise model, characterized by a fixed-norm vector field, is unstable. We found the instability by explicitly solving the linearized equations for the most general set of perturbations around this background, and by noticing that the solutions diverge close to horizon crossing. This happens because one perturbation becomes a ghost at that moment. A simplified computation, with only the perturbations of the vector field included, shows the same instability, clarifying the origin of the problem. We then discuss several other models, with a particular emphasis on the case of a nonminimal coupling to the curvature, in which vector fields are used either to support an anisotropic expansion, or to generate cosmological perturbations on an isotropic background. In many cases, the mass squared of the vector needs to be negative; we show that, as a consequence, the longitudinal vector mode is a ghost (a field with negative kinetic term, and negative energy, and not simply a tachyon). We comment on problems that arise at the quantum level. In particular, the presence of a ghost can be a serious difficulty for the UV completion that such models require in the subhorizon regime.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

A Forward Analytic Model of Neutron Time-of-Flight Signals for Inferring Ion Temperatures from MagLIF Experiments

A forward analytic model is required to rapidly simulate the neutron time-of-flight (nToF) signals that result from magnetized liner inertial fusion (MagLIF) experiments at Sandia’s Z Pulsed Power Facility. Various experimental parameters, such as the burn-weighted fuel-ion temperature and liner areal density, determine the shape of the nToF signal and are important for characterizing any given MagLIF experiment. Extracting these parameters from measured nToF signals requires an appropriate analytic model that includes the primary deuterium-deuterium neutron peak, once-scattered neutrons in the beryllium liner of the MagLIF target, and direct beamline attenuation. Here, mathematical expressions for this model were derived from the general-geometry time- and energy-dependent neutron transport equation with anisotropic scattering. Assumptions consistent with the time-of-flight technique were used to simplify this linear Boltzmann transport equation into a more tractable form. Models of the uncollided and once-collided neutron scalar fluxes were developed for one of the five nToF detector locations at the Z-Machine. Numerical results from these models were produced for a representative MagLIF problem and found to be in good agreement with similar neutron transport simulations. Twenty experimental MagLIF data sets were analyzed using the forward models, which were determined to only be significantly sensitive to the ion temperature. The results of this work were also found to agree with values obtained separately using a zero scatter analytic model and a high-fidelity Monte Carlo simulation. Finally, inherent difficulties in this and similar techniques are identified, and a new approach forward is suggested.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Analytic approach to nonlinear hydrodynamic instabilities driven by time-dependent accelerations

We extend our earlier model for Rayleigh-Taylor and Richtmyer-Meshkov instabilities to the more general class of hydrodynamic instabilities driven by a time-dependent acceleration g(t) . Explicit analytic solutions for linear as well as nonlinear amplitudes are obtained for several g(t)'s by solving a Schroedinger-like equation d{sup 2}{eta}/dt{sup 2} - g(t)kA{eta} = 0 where A is the Atwood number and k is the wavenumber of the perturbation amplitude {eta}(t). In our model a simple transformation k {yields} k{sub L} and A {yields} A{sub L} connects the linear to the nonlinear amplitudes: {eta}{sup nonlinear} (k,A) {approx} (1/k{sub L})ln{eta}{sup linear} (k{sub L}, A{sub L}). The model is found to be in very good agreement with direct numerical simulations. Bubble amplitudes for a variety of accelerations are seen to scale with s defined by s = {integral} {radical}g(t)dt, while spike amplitudes prefer scaling with displacement {Delta}x = {integral}[{integral}g(t)dt]dt.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Measurement of Fission Product Concentration Profiles in AGR-3/4 TRISO Fuel Graphitic Matrix and Nuclear Graphites

The third Advanced Gas Reactor (AGR) irradiation experiment, AGR-3/4, was designed to investigate the migration of fission products in fuel compact graphitic matrix and reactor graphite components. Using destructive methods, radial fission product concentration profiles were measured for gamma-emitting fission products (e.g., Ag-110m, Cs-134, and Eu-154) and beta-emitting Sr-90 in irradiated graphitic and graphite components from six different AGR-3/4 irradiation capsules. These new measured concentration profiles can now be compared to non-destructive measurements and fission product transport simulations and will be used to derive new diffusivities and sorptivities to support refinement of fission product transport models and high-temperature gas-cooled reactor (HTGR) source-term analyses. Each capsule in the AGR-3/4 experiment had four fuel compacts in the middle of two concentric rings of graphitic matrix material, PCEA graphite, or IG-110 graphite. In addition to the approximately 1898 tristructural isotropic (TRISO) coated particles in each compact, there were 20 designed to fail (DTF) particles coated only in pyrocarbon so that they released fission products into the surrounding cylindrical rings of carbonaceous materials. Destructive sampling of the rings involved machining/milling material from around the circumference of the rings, collecting that material, and performing radiochemical analyses on it. Milling operations were performed in multiple steps or segments, and each segment was generally 0.508 mm (0.020 in) thick. Knowing the radial position at which each segment was milled, the volume of the milled material at each segment, and the fission product content in each segment, the radial fission product concentrations were constructed for select isotopes in each ring. Ag-110m profiles had the most variation. Some profiles were peaked at an inner or outer surface. Some were peaked at the middle of the ring wall thickness. Some increased radially outward, and some decreased radially outward. These types of variations and the fact that the measured profiles do not generally compare favorably with the transport model employed for AGR-3/4 may adversely impact the ability to extract reasonable transport parameters for this isotope. In many cases, the Cs-134 profiles decreased somewhat linearly in the outward radial direction, and in cursory comparisons, the shapes of these profiles appeared similar to those from model predictions. The step changes in concentration across the inner-outer ring gap were generally consistent with the model predictions as well. In some cases, there were local maxima in concentration at the outer surface of the rings. This suggests that fission products could have transported in the small gaps between the inner ring and the outer ring and between the outer ring and the sink ring such that some portion of a given fission product can bypass diffusion through the ring itself. The analysis of the small nubs on the outer surfaces of some of the outer rings revealed fission product concentrations in the nubs that were often higher than in the outermost segments of the rings. This further supports the hypothesis that short-circuit, gap transport occurred, causing relatively high surface concentrations on the outer surfaces of the rings. Eu-154 and Sr-90 profiles tend to have very similar shapes, suggesting that they transport via the same mechanisms. The observed profiles were indicative of a transport process where the isotopes are sorbed on the inner surface of the ring, but diffusion into the ring from that surface is quite slow. Some elevated concentrations of Sr-90 (relative to Eu-154) on the outer surface of a ring suggested that rapid, gas-gap transport of gaseous precursor Kr-90 and volatile Rb-90 could have occurred prior to their decaying to Sr-90. Overall, the Eu 154 and Sr-90 profiles were still very similar, which indicates that the transport of short-lived Sr-90 precursors is not a major effect. In some capsules, the qualitative Sr-90 behavior across the ring gaps was consistent with the model (using the available legacy Sr-90 transport parameters), but in other capsules the model was inconsistent with the measurements and seems to underestimate the amount of Sr-90 in the outer rings. The total ring Sr-90 inventories were estimated for all the rings that were subject to physical sampling. These results will be used to adjust the predicted particle and/or compact releases used in the AGR-3/4 fission product transport model. Given the different irradiation temperatures among the capsules and the rings, it was not possible to discern fundamental differences in the transport of isotopes within the different carbon materials, i.e., graphitic matrix, IG-110, or PCEA. It may be possible to do this in the course of determining transport from the concentration profiles in future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Constructor selection system

Future space construction missions will involve both human and machine constructors. Selection of the optimum constructor mix requires a model of constructor capabilities and requirements. The database for that model is developed via extrapolation from current literature. Optimization is done via minimization of total mission cost using a linear programming approach. This prototype is the first cut at producing a general tool for choosing a near-optimum constructor mix for any space construction mission. It illuminates some significant representational and data-gathering problems with the modelling approach.

Johnson, Richard↗

Impact of ethanol blending into gasoline on aromatic compound evaporation and particle emissions from a gasoline direct injection engine

This study examined the interactions of ethanol with aromatic compounds on aromatic species evolution during gasoline evaporation and the consequent impacts on particle emissions from a single-cylinder, gasoline direct injection engine. From a chemical kinetic standpoint, the dilution of the aromatic species in gasoline by ethanol blending should reduce particle emissions because aromatics are the primary species that form particles during gasoline combustion. However, increased evaporative cooling from the ethanol and ethanol's effect on when aromatics in the fuel droplet (or surface film or pool) evaporate can drive an increase in particle emissions. The objective of this study was to quantify these competing effects. The results show that a combination of ethanol's increased evaporative cooling and impact on aromatic compound vapor-liquid equilibrium can extend droplet lifetime and cause aromatics to evaporate later in the droplet evaporation process than would be the case without ethanol. When fuels were burned in a direct-injection single-cylinder engine at high speed (2500 rpm) and relatively high load, ethanol blending caused an increase in particle emissions for fuels containing a low vapor pressure aromatic. At a lower speed (1500 rpm), no statistically significant increase in particle emissions was observed, likely because more time was available for evaporation and mixing to occur. In contrast, particle emissions from a fuel blended with a high vapor pressure aromatic were either insensitive to or reduced by ethanol blending, likewise to engine operating conditions. Current models for predicting particle emissions from gasoline engines, such as particulate matter index (PMI), generally lack variables for non-linear interactions between ethanol and gasoline hydrocarbons. To identify nonlinear interactions between predictor variables that might better explain the observed particle emissions, the least absolute shrinkage and selection operator (LASSO) regularized regression approach was employed. Among the predictor variables evaluated was the Yield Sooting Index (YSI) which is as an improved measure to quantify the aromatic's chemical tendency to generate particle emissions. Following this analysis, two variables were selected based on their frequent appearance. The first was ethanol mole percent multiplied by aromatic mole percent divided by aromatic vapor pressure [(EtOH * Aro%)/Aro VP@443 K]. The second was aromatic mole percent multiplied by aromatic YSI divided by aromatic molecular weight [(Aro% * Aro YSI)/Aro MW]. The results of linear regression including only these two combined explanatory variables achieved an r 2 = 0.959, substantially improved over the PMI model (r 2 = 0.688) and provides insight into how the PMI formalism might be modified to account for non-linear oxygenate-hydrocarbon coupling.

09 BIOMASS FUELS↗

Revising the dynamic energy budget theory with a new reserve mobilization rule and three example applications to bacterial growth

Dynamic energy budget (DEB) theory has been applied to model a wide range of organisms, including microbes. In the standard DEB model, biomass is partitioned into reserve and structural compartments, where reserve biomass is mobilized in a pseudolinear manner (while the reserve biomass density, defined as the ratio between reserve and structural biomass, decays linearly) to drive maintenance and the growth of structural biomass (and extracellular enzyme production if it is considered). However, the linear dynamics of the reserve biomass density makes the standard DEB model incapable of explaining the slowdown of microbial growth at high reserve density that is caused by macromolecular crowding effect which reduces biochemical reaction rates (a typical situation occurs when microbes are experiencing severe moisture stress) and is inconsistent with the observation that intracellular enzymatic reactions generally follow non-linear kinetics. By partitioning biomass into reserve, kinetic, and structural compartments, we show here that the Equilibrium Chemistry Approximation (ECA) kinetics can be used to represent enzymatically catalyzed reserve biomass mobilization that can then drive the kinetic and structural biomass synthesis. This revised DEB model better represents the tradeoff in ribosome allocation for structural growth and internal enzyme production, is structurally compatible with metabolic models of cell individuals, and includes the standard DEB model and the popular compromise model as special cases for representing population growth. We then applied the revised DEB model to interpret components of bacterial respiration, their dependence on substrate availability, and emergent microbial carbon use efficiency dynamics for an exponentially growing population. We found that the revised DEB model enables a better understanding of bacterial substrates use (carbon in our examples) than that can be derived from a few other models in the literature. In particular, the revised DEB model explains why carbon use efficiency may first increase, then plateau, and finally decrease with growth rate (and substrate uptake rate), as a function of proteomics. Additionally, the revised DEB model explains why the kinetic biomass compartment needs to be divided to reasonably incorporate proteomic control of microbial growth.

59 BASIC BIOLOGICAL SCIENCES↗

Integrated controls-structures design methodology development for a class of flexible spacecraft

Future utilization of space will require large space structures in low-Earth and geostationary orbits. Example missions include: Earth observation systems, personal communication systems, space science missions, space processing facilities, etc., requiring large antennas, platforms, and solar arrays. The dimensions of such structures will range from a few meters to possibly hundreds of meters. For reducing the cost of construction, launching, and operating (e.g., energy required for reboosting and control), it will be necessary to make the structure as light as possible. However, reducing structural mass tends to increase the flexibility which would make it more difficult to control with the specified precision in attitude and shape. Therefore, there is a need to develop a methodology for designing space structures which are optimal with respect to both structural design and control design. In the current spacecraft design practice, it is customary to first perform the structural design and then the controller design. However, the structural design and the control design problems are substantially coupled and must be considered concurrently in order to obtain a truly optimal spacecraft design. For example, let C denote the set of the 'control' design variables (e.g., controller gains), and L the set of the 'structural' design variables (e.g., member sizes). If a structural member thickness is changed, the dynamics would change which would then change the control law and the actuator mass. That would, in turn, change the structural model. Thus, the sets C and L depend on each other. Future space structures can be roughly divided into four mission classes. Class 1 missions include flexible spacecraft with no articulated appendages which require fine attitude pointing and vibration suppression (e.g., large space antennas). Class 2 missions consist of flexible spacecraft with articulated multiple payloads, where the requirement is to fine-point the spacecraft and each individual payload while suppressing the elastic motion. Class 3 missions include rapid slewing of spacecraft without appendages, while Class 4 missions include general nonlinear motion of a flexible spacecraft with articulated appendages and robot arms. Class 1 and 2 missions represent linear mathematical modeling and control system design problems (except for actuator and sensor nonlinearities), while Class 3 and 4 missions represent nonlinear problems. The development of an integrated controls/structures design approach for Class 1 missions is addressed. The performance for these missions is usually specified in terms of (1) root mean square (RMS) pointing errors at different locations on the structure, and (2) the rate of decay of the transient response. Both of these performance measures include the contributions of rigid as well as elastic motion.

Maghami, P. G.↗

Analytic approach to nonlinear hydrodynamic instabilities driven by time-dependent accelerations

We extend our earlier model for Rayleigh-Taylor and Richtmyer-Meshkov instabilities to the more general class of hydrodynamic instabilities driven by a time-dependent acceleration g(t). Explicit analytic solutions for linear as well as nonlinear amplitudes are obtained for several g(t)s by solving a Schroedinger-like equation d{sup 2}eta/dt{sup 2}-g(t)kAeta=0, where A is the Atwood number and k is the wave number of the perturbation amplitude eta(t). In our model a simple transformation k->k{sub L} and A->A{sub L} connects the linear to the nonlinear amplitudes: eta{sup nonlinear}(k,A)approx(1/k{sub L})ln eta{sup linear}(k{sub L},A{sub L}). The model is found to be in very good agreement with direct numerical simulations. Bubble amplitudes for a variety of accelerations are seen to scale with s defined by s=integralsq root(g(t))dt, while spike amplitudes prefer scaling with displacement DELTAx=integral[integralg(t)dt]dt.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗