Search NASA⌕ Search

SEARCH · Search NASA

Results for “hematite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Simultaneous leaching and carbon sequestration in constrained aqueous solutions

The behavior of metal ions leaching and precipitated mineral phases of metal-rich fly ash (FA) was examined in order to evaluate microbial impacts on carbon sequestration and metal immobilization. The leaching solutions consisted of aerobic deionized water (DW) and artificial eutrophic water (AEW) that was anaerobic, organic- and mineral-rich, and higher salinity as is typical of bottom water in eutrophic algae ponds. The Fe- and Ca-rich FAs were predominantly composed of quartz, mullite, portlandite, calcite, hannebachite, maghemite, and hematite. After 86 days, only Fe and Ca contents exhibited a decrease in leaching solutions while other major and trace elements showed increasing or steady trends in preference to the type of FA and leaching solution. Ca-rich FA showed strong carbon sequestration efficiency ranging up to 32.3 g CO(2)/kg FA after 86 days, corresponding to almost 65% of biotic carbon sequestration potential under some conditions. Variations in the properties of FAs such as chemical compositions, mineral constituents as well as the type of leaching solution impacted CO(2) capture. Even though the relative amount of calcite increased sixfold in the AEW and the relative amount of mineral phase reached 37.3 wt% using Ca-rich FA for 86 days, chemical sequestration did not accomplish simultaneous precipitation and sequestration of several heavy metals.

54 ENVIRONMENTAL SCIENCES↗

High-pressure Evolution of Fe2O3 Electronic Structure Revealed by X-ray Absorption

We report the high-pressure measurement of the Fe K edge in hematite (Fe{sub 2}O{sub 3}) by x-ray absorption spectroscopy in partial fluorescence yield geometry. The pressure-induced evolution of the electronic structure as Fe{sub 2}O{sub 3} transforms from a high-spin insulator to a low-spin metal is reflected in the x-ray absorption pre-edge. The crystal-field splitting energy was found to increase monotonically with pressure up to 48 GPa, above which a series of phase transitions occur. Atomic multiplet, cluster diagonalization, and density-functional calculations were performed to simulate the pre-edge absorption spectra, showing good qualitative agreement with the measurements. The mechanism for the pressure-induced electronic phase transitions of Fe{sub 2}O{sub 3} is discussed and it is shown that ligand hybridization significantly reduces the critical high-spin/low-spin transition pressure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Preparation and magnetic properties of spindle porous iron nanoparticles

Spindle porous iron nanoparticles were firstly synthesized by reducing the pre-synthesized hematite ({alpha}-Fe{sub 2}O{sub 3}) spindle particles with hydrogen gas. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption/desorption isotherms and vibrating sample magnetometry (VSM). A lattice shrinkage mechanism was employed to explain the formation process of the porous structure, and the adsorbed phosphate was proposed as a protective shell in the reduction process. N{sub 2} adsorption/desorption result showed a Brunauer-Emmett-Teller (BET) surface area of 29.7 m{sup 2}/g and a continuous pore size distribution from 2 nm to 100 nm. The magnetic hysteresis loop of the synthesized iron particles showed a saturation magnetization of 84.65 emu/g and a coercivity of 442.36 Oe at room temperature.

36 MATERIALS SCIENCE↗

MICROSCANNING XRF, XANES, AND XRD STUDIES OF THEDECORATED SURFACE OF ROMAN TERRA SIGILLATA CERAMICS

Different microscanning synchrotron techniques were used to better understand the elaboration process and origins of Terra Sigillata potteries from the Roman period. A mixture Gallic slip sample cross-section showing red and yellow colors was studied. The small (micron) size of the X-ray beam available at Stanford Synchrotron Radiation Laboratory (SSRL) and Advanced Light Source (ALS) synchrotron sources, coupled with the use of a sample scanning stage allowed us to spatially resolve the distribution of the constitutive mineral phases related to the chemical composition. Results show that red color is a result of iron-rich hematite crystals and the yellow part is a result of the presence of Ti-rich rutile-type phase (brookite). Volcanic-type clay is at the origin of these marble Terra Sigillata.

36 MATERIALS SCIENCE↗

Characterization of Solids in Residual Wastes from Single-Shell Tanks at the Hanford Site, Washington, USA - 9277

Solid-phase characterization methods have been used in an ongoing study of residual wastes (i.e., waste remaining after final retrieval operations) from the underground single-shell storage tanks 241-C-103, 241-C-106, 241-C-202, 241-C-203, and 241-S-112 at the U.S. Department of Energy’s Hanford Site in Washington State. The results of studies completed to date show significant variability in the compositions of those residual wastes and the compositions, morphologies, and crystallinities of the individual phases that make up these wastes. These differences undoubtedly result from the various waste types stored and transferred in and out each tank and the sluicing and retrieval operations used for waste retrieval. Our studies indicate that these residual wastes are chemically-complex assemblages of crystalline and amorphous solids that contain contaminants as discrete phases and/or co-precipitated within oxide phases. Depending on the specific tank, various solids (e.g., gibbsite; boehmite; dawsonite; cancrinite; Fe oxides such as hematite, goethite, and maghemite; rhodochrosite; lindbergite; whewellite; nitratine; and numerous amorphous or poorly crystalline phases) have been identified by X-ray diffraction and scanning electron microscopy/energy dispersive X-ray spectroscopy in residual wastes studied to date. Our studies also show that contact of residual wastes with Ca(OH)2- and CaCO3-saturated aqueous solutions, which were used as surrogates for the compositions of pore-fluid leachants derived from young and aged cements respectively, may alter the compositions of solid phases present in the contacted wastes. Fe oxides/hydroxides have been identified in all residual wastes studied to date. They occur in these wastes as discrete particles, particles intergrown within a matrix of other phases, and surface coatings on other particles or particle aggregates. These Fe oxides/hydroxides typically contain trace concentrations of other transition metals, such Cr, Mn, Ni, and/or Pb. Recent analyses of residual waste from 241-C-103 have revealed the presence of Tc-containing Fe oxide/hydroxide particles, which is believed to be the first direct evidence of Tc in solid phases in actual samples of Hanford pre-retrieval tank waste or post-retrieval residual waste. The presence of mineralized coatings, such as Fe oxides/hydroxides or reaction products precipitated from contact with cement pore fluids, on contaminant-containing particles could decrease the rate of dissolution of these particles and thus the release of contaminants until the coatings had dissolved sufficiently to expose the underlying matrix to infiltrating pore fluids. Certain key cross-cutting geochemical processes and solid phase characteristics important to contaminant waste release are becoming evident, now that residual wastes have been studied from several single-shell tanks. As more residual tank wastes are characterized in terms of composition and contaminant release, it is anticipated that common characteristics with respect to the type of waste stored in the tank will become evident. This may allow the grouping of tanks into general categories with certain common chemical features and contaminant release characteristics - an important goal because complete characterization of residual wastes from all 149 single-shell storage tanks is not practical.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Morphological Evolution of Oxide Scales Grown on Ferritic Steels in Steam

This study is concerned with the thermally-grown oxide scales formed inside tubes in a steam boiler during normal operation, and the influence of the morphological evolution of those scales on how strains are developed and accommodated. Understanding such details is an important consideration in modeling the tendency for scale spallation or exfoliation. Overall, the scales formed on ferritic steels in steam can be simplistically described as a layer of essentially pure magnetite in contact with the steam, and a second layer of magnetite containing alloying elements (especially Cr) next to the alloy. Hematite also can develop as a third, outermost oxide layer that may be non-uniform in thickness, and penetrate inwards along grain boundaries in the magnetite layer. A peculiar variant of this morphology often reported on low-alloy ferritic steels after boiler service (but not on laboratory-oxidized specimens) has a relatively thick outer magnetite layer and multiple inner layers described as decreasing in thickness as the alloy surface is approached. These inner layers appear to be repeating sets of double layers of pure magnetite and magnetite containing alloying elements. The results of detailed examination of such multi-layered morphology and the implications for the mode of scale growth and failure are discussed.

36 MATERIALS SCIENCE↗

Characterizing Solids in Residual Wastes from Single-Shell Tanks at the Hanford Site.

Solid-phase characterization methods have been used in an ongoing study of residual wastes (i.e., waste remaining after final retrieval operations) from underground single-shell storage tanks 241-C-103, 241 C 106, 241-C-202, 241-C-203, and 241-S-112 at the U.S. Department of Energy’s Hanford Site in Washington State. The results of studies completed to date show variability in the compositions of those residual wastes and the compositions, morphologies, and crystallinities of the individual phases that make up these wastes. These differences undoubtedly result from the various waste types stored and transferred into and out of each tank and the different sluicing and retrieval operations used for waste retrieval. The studies indicate that these residual wastes are chemically-complex assemblages of crystalline and amorphous solids that contain contaminants as discrete phases and/or coprecipitated within oxide/hydroxide phases. Depending on the specific tank, various solids (e.g., gibbsite; böhmite; dawsonite; cancrinite; Fe oxides/hydroxides such as hematite, goethite, and maghemite; rhodochrosite; lindbergite; whewellite; nitratine; and numerous amorphous or poorly crystalline phases) have been identified by X-ray diffraction and scanning electron microscopy/energy dispersive X-ray spectroscopy in residual wastes studied to date. The studies also show that contact of residual wastes with Ca(OH)2- and CaCO3-saturated aqueous solutions, which were used as surrogates for the compositions of pore-fluid leachants derived from young and aged cements, respectively, may alter the composition of solid phases present in the contacted wastes. Iron oxides/hydroxides have been identified in all residual wastes studied to date. They occur in these wastes as discrete particles, particles intergrown within a matrix of other phases, and surface coatings on other particles or particle aggregates. These Fe oxides/hydroxides typically contain trace concentrations of other transition metals, such Cr, Mn, Ni, Pb, and/or U. Recent analyses of residual waste from 241-C-103 have revealed the presence of Tc-containing Fe oxide/hydroxide particles, which is believed to be the first direct evidence of Tc in solid phases in actual samples of Hanford pre-final retrieval tank waste or post-final retrieval residual waste. The presence of mineralized coatings, such as Fe oxides/hydroxides or reaction products precipitated from contact with cement pore fluids, on contaminant-containing particles could decrease their rate of dissolution, thereby delaying the release of contaminants until the coatings dissolve sufficiently to expose the underlying matrix to infiltrating pore fluids. Certain key cross-cutting geochemical processes and solid phase characteristics important to contaminant waste release are becoming evident, now that residual wastes have been studied from several single-shell tanks. As more residual tank wastes are characterized in terms of composition and contaminant release, it is anticipated that common characteristics with respect to the type of wastes stored in the tanks will become evident. This may allow the grouping of tanks into general categories with certain common chemical features and contaminant release characteristics - an important goal because complete characterization of residual wastes from all 149 single-shell storage tanks is not practical. Additionally, information garnered from residual waste characterization activities can be used to optimize future waste retrieval operations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

THE WEATHERING OF A SULFIDE OREBODY: SPECIATION AND FATE OF SOME POTENTIAL CONTAMINANTS

Various potentially toxic trace elements such as As, Cu, Pb and Zn have been remobilized by the weathering of a sulfide orebody that was only partially mined at Leona Heights, California. As a result, this body has both natural and anthropogenically modified weathering profiles only 500 m apart. The orebody is located in a heavily urbanized area in suburban Oakland, and directly affects water quality in at least one stream by producing acidic conditions and relatively high concentrations of dissolved elements (e.g., {approx}500 mg/L Cu, {approx}3700 mg/L Zn). Micrometric-scale mineralogical investigations were performed on the authigenic metal-bearing phases (less than 10 {mu}m in size) using electron-probe micro-analysis (EPMA), micro-Raman, micro X-ray absorption spectroscopy (mXAS), scanning X-ray diffraction (mSXRD) and scanning X-ray fluorescence (mSXRF) mapping techniques. Those measurements were coupled with classical mineralogical laboratory techniques, X-ray diffraction (XRD) and scanning electron microscopy (SEM). Authigenic metal-bearing phases identified are mainly sulfates (jarosite, epsomite, schwertmannite), Fe (oxy-)hydroxides (goethite, hematite and poorly crystalline Fe products) and poorly crystalline Mn (hydr-)oxides. Sulfates and Fe (oxy-)hydroxides are the two main secondary products at both sites, whereas Mn (hydr-) oxides were only observed in the samples from the non-mining site. In these samples, the various trace elements show different affinities for Fe or Mn compounds. Lead is preferentially associated with Mn (hydr-)oxides and As with Fe (oxy-)hydroxides or sulfates. Copper association with Mn and Fe phases is questionable, and the results obtained rather indicate that Cu is present as individual Cu-rich grains (Cu hydroxides). Some ochreous precipitates were found at both sites and correspond to a mixture of schwertmannite, goethite and jarosite containing some potentially toxic trace elements such as Cu, Pb and Zn. According to the trace element distribution and relative abundance of the unweathered sulfides, this orebody still represents a significant reservoir of potential contaminants for the watershed, especially in the non-mining site, as a much greater proportion of sulfides is left to react and because of the lower porosity in this site.

54 ENVIRONMENTAL SCIENCES↗

JV Task 95-Particulate Control Consulting for Minnesota Ore Operations

The purpose of the project was to assist U.S. Steel in the evaluation, selection, planning, design, and testing of potential approaches to help meet U.S. Steel's goal for low-particulate matter emissions and regulatory compliance. The energy-intensive process for producing iron pellets includes treating the pellets in high-temperature kilns in which the iron is converted from magnetite to hematite. The kilns can be fired with either natural gas or a combination of gas and coal or biomass fuel and are equipped with wet venturi scrubbers for particulate control. Particulate measurements at the inlet and outlet of the scrubbers and analysis of size-fractionated particulate samples led to an understanding of the effect of process variables on the measured emissions and an approach to meet regulatory compliance.

01 COAL, LIGNITE, AND PEAT↗

Discrete element modeling of indentation tests to investigate mechanisms of CO 2 -related chemomechanical rock alteration

During CO 2 injection into geological formations, petrophysical and geomechanical properties of host formations can be altered due to mineral dissolution and precipitation. Field and laboratory results have shown that sandstone and siltstone can be altered by CO 2 -water mixtures, but few quantitative studies have been performed to fully investigate underlying mechanisms. Based on the hypothesis that CO 2 -water mixtures alter the integrity of rock structure by attacking cements rather than grains, we attempt to explain the degradation of cementation due to long-term contact with CO 2 and water and mechanisms for changes in rock mechanical properties. Many sandstones, including calcite-cemented quartzitic sandstone, chlorite-cemented quartzitic sandstone, and hematite-cemented quartzitic sandstone, contain interparticle cements that are more readily affected by CO 2 -water mixtures than grains. A model that couples the discrete element method and the bonded-particle model is used to perform simulations of indentation tests on synthetic rocks with crystal and random packings. The model is verified against the analytical cavity expansion model and validated against laboratory indentation tests on Entrada sandstone with and without CO 2 alteration. Sensitivity analysis is performed for cementation microscopic parameters including stiffness, size, axial, and shear strength. The simulation results indicate that the CO 2 -related degradation of mechanical properties in bleached Entrada sandstone can be attributed to the reduction of cement size rather than cement strength. Finally, our study indicates that it is possible to describe the CO 2 -related rock alteration through particle-scale mechanisms.

54 ENVIRONMENTAL SCIENCES↗

The eruptibility of magmas at Tharsis and Syrtis Major on Mars

Magnetic and geologic data indicate that the ratio of intrusive to extrusive magmatism (the I/E ratio) is higher in the Tharsis and Syrtis Major volcanic provinces on Mars relative to most volcanic centers on Earth. The fraction of magmas that erupt helps to determine the effects of magmatism on crustal structure and the flux of magmatic gases to the atmosphere and also influences estimates of melt production inferred from the history of surface volcanism. We consider several possible controls on the prevalence of intrusive magmatism at Tharsis and Syrtis Major, including melt production rates, lithospheric properties, regional stresses and strain rates, and magmatic volatile budgets. The Curie temperature is the minimum crustal temperature required for thermal demagnetization, implying that if the primary magnetic mineral is magnetite or hematite, the crust was warm during the intrusive magmatism reflected in Tharsis and Syrtis Major I/E ratios. When wall rocks are warm, thermally activated creep relaxes stresses from magma replenishment and regional tectonics, and eruptibility depends on buoyancy overpressure. We develop a new one-dimensional model for the development of buoyancy in a viscous regime that accounts for cooling, crystallization, volatile exsolution, bubble coalescence and rise, fluid egress, and compaction of country rock. Under these conditions, we find that initial water and CO 2 contents typically < 1.5 wt % can explain the observed range of intrusive/extrusive ratios. Furthermore, our results support the hypothesis that warm crust and a relatively sparse volatile budget encouraged the development of large intrusive complexes beneath Tharsis and Syrtis Major.

58 GEOSCIENCES↗

Oxidative Alteration of Ferrous Smectites and Implications for the Redox Evolution of Early Mars: Oxidation Products of Ferrous Smectites

Surface conditions on early Mars were likely anoxic, similar to early Earth, but the timing of the evolution to oxic conditions characteristic of contemporary Mars is unresolved. Ferrous trioctahedral smectites are the thermodynamically predicted products of anoxic basalt weathering, but orbital analyses of Noachian-aged terrains find primarily Fe 3+ -bearing clay minerals. Rover-based detection of Fe 2+ -bearing trioctahedral smectites at Gale Crater suggests that ferrous smectites are the unoxidized progenitors of orbitally detected ferric smectites. To assess this pathway, we conducted ambient-temperature oxidative alteration experiments on four synthetic ferrous smectites having molar Fe/(Mg + Fe) from 1.00 to 0.33. Smectite suspension in air-saturated solutions produced incomplete oxidation (24–38% Fe 3+ /ΣFe). Additional smectite oxidation occurred upon reexposure to air-saturated solutions after anoxic hydrothermal recrystallization, which accelerated cation and charge redistribution in the octahedral sheet. Oxidation was accompanied by contraction of the octahedral sheet (d (060) decreased from 1.53–1.56 Å to 1.52 Å), consistent with a shift toward dioctahedral structure. Ferrous smectite oxidation by aqueous hydrogen peroxide solutions resulted in nearly complete Fe 2+ oxidation but also led to partial Fe 3+ ejection from the structure, producing nanoparticulate hematite. Reflectance spectra of oxidized smectites were characterized by (Fe 3+ ,Mg) 2 -OH bands at 2.28–2.30 μm, consistent with oxidative formation of dioctahedral nontronite. Accordingly, ferrous smectites are plausible precursors to observed ferric smectites on Mars, and their presence in late-Noachian sedimentary units suggests that anoxic conditions may have persisted on Mars beyond the Noachian.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

First Principle Estimation of Geochemically Important Transition Metal Oxide Properties: Structure and Dynamics of the Bulk, Surface and Mineral/Aqueous Fluid Interface

Reactions in the mineral surface/reservoir fluid interface control many geochemical processes such as the dissolution and growth of minerals (Yanina and Rosso 2008), heterogeneous oxidation/reduction (Hochella 1990, Brown 2001, Hochella, Lower et al. 2008, Navrotsky, Mazeina et al. 2008), and inorganic respiration (Newman 2010). Key minerals involved in these processes are the transition metal oxides and oxyhydroxides (e.g., hematite, Fe2O3, and goethite, FeOOH)(Brown, Henrich et al. 1999, Brown 2001, Hochella, Lower et al. 2008, Navrotsky, Mazeina et al. 2008). To interpret and predict these processes, it is necessary to have a high level of understanding of the interactions between the formations containing these minerals and their reservoir fluids. However, these are complicated chemical events occurring under a wide range of T, P, and X conditions and the interpretation is complicated by the highly heterogeneous nature of natural environments (Hochella 1990, Hochella, Lower et al. 2008, Navrotsky, Mazeina et al. 2008) and the electronic and structural complexity of the oxide materials involved(Cox 1992, Kotliar and Vollhardt 2004, Navrotsky, Mazeina et al. 2008). In addition, also because of the complexity of the minerals involved and the heterogeneous nature of natural systems, the direct observation of these reactions at the atomic level is experimentally extremely difficult. Theoretical simulations will provide important support for analysis of the geochemistry of the mineral surface/fluid region as well as provide essential tools to extrapolate laboratory measurements to the field environment.

Environmental Molecular Sciences Laboratory↗

The Influence of Ozone: Superstoichiometric Oxygen in Atomic Layer Deposition of Fe 2 O 3 Using tert -Butylferrocene and O 3

Understanding the chemical mechanisms at play in atomic layer deposition (ALD) is critical for effective process development and expansion of ALD into more complex classes of materials. In this work, a mechanistic study of iron oxide deposited by ALD using tert-butylferrocene and ozone as reactants is performed. Iron oxide ALD using ozone is a useful model system for mechanistic studies due to the prevalence of ozone-based ALD processes and the uses of iron oxide in ternary and quaternary metal oxides. Results show that saturation conditions require significantly greater exposures of both reactants than is typically reported in the literature, and growths per cycle of greater than one monolayer of Fe 2 O 3 per cycle are observed and explained. A growth mechanism is proposed whereby increased ozone exposure results in uptake of superstoichiometric oxygen into the film. X-ray characterizations reveal the presence of excess oxygen stored near the surface of films deposited with larger ozone exposures and show that increased ozone exposures cause crystalline domain rearrangement and conversion of the film from the γ-maghemite phase to the α-hematite phase. The mechanism described here has implications for the wider class of ozone-based ALD processes, and potential applications of this growth phenomenon are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrical and Spectroscopic Diagnostics as Real‐Time Metallization Indicators During Hydrogen Plasma Smelting Reduction

This study investigates the hydrogen (H 2 ) plasma reduction process of direct-reduced-iron-grade hematite ore at different arc currents (100–200 A) in an Ar–5% H 2 atmosphere at 0.9 bar. Iron ore samples (10 g) were exposed to a plasma arc, and the reduction/metallization kinetics were analyzed over fixed time intervals. Electrical diagnostics revealed that the arc voltage exhibited takeover-mode oscillations which were suppressed at higher currents due to stronger electromagnetic coupling. The voltage dropped significantly as metallization approached ∼95%, linked to increased electrical conductivity of the metallic iron (Fe) in the ore as well as Fe evaporation into the arc, lowering the arc resistance. A simplified Elenbaas–Heller model supported this explanation and confirmed that Fe vapor concentration enhances plasma conductivity. Optical emission spectroscopy focused on the plasma–metal interface revealed the plasma's optically thick nature, as the primary Fe I 526.95 nm line experienced self-absorption. However, weaker Fe I lines (404.58, 438.35 nm) normalized to Ar I 696.5 nm provided a reliable proxy for metallization. These diagnostics, electrical and spectroscopic, effectively track metallization in real-time during H 2 plasma smelting reduction.

08 HYDROGEN↗

Retarded Charge-Carrier Recombination in Photoelectrochemical Cells from Plasmon-Induced Resonance Energy Transfer

N-type metal oxides such as hematite (α-Fe 2 O 3 ) and bismuth vanadate (BiVO 4 ) are promising candidate materials for efficient photoelectrochemical water splitting; however, their short minority carrier diffusion length and restricted carrier lifetime result in undesired rapid charge recombination. In this paper, a 2D arranged globular Au nanosphere (NS) monolayer array with a highly ordered hexagonal hole pattern (hereafter, Au array) is introduced onto the surface of photoanodes comprised of metal oxide films via a facile drying and transfer-printing process. Through plasmon-induced resonance energy transfer, the Au array provides a strong electromagnetic field in the near-surface area of the metal oxide film. The near-field coupling interaction and amplification of the electromagnetic field suppress the charge recombination with long-lived photogenerated holes and simultaneously enhance the light harvesting and charge transfer efficiencies. Consequently, an over 3.3-fold higher photocurrent density at 1.23 V versus reversible hydrogen electrode (RHE) is achieved for the Au array/α-Fe 2 O 3 . Furthermore, the high versatility of this transfer printing of Au arrays is demonstrated by introducing it on the molybdenum-doped BiVO 4 film, resulting in 1.5-fold higher photocurrent density at 1.23 V versus RHE. The tailored metal film design can provide a potential strategy for the versatile application in various light-mediated energy conversion and optoelectronic devices.

2D pattern array↗

Low Catalyst Loading Enhances Charge Accumulation for Photoelectrochemical Water Splitting

Abstract Solar water oxidation is a critical step in artificial photosynthesis. Successful completion of the process requires four holes and releases four protons. It depends on the consecutive accumulation of charges at the active site. While recent research has shown an obvious dependence of the reaction kinetics on the hole concentrations on the surface of heterogeneous (photo)electrodes, little is known about how the catalyst density impacts the reaction rate. Using atomically dispersed Ir catalysts on hematite, we report a study on how the interplay between the catalyst density and the surface hole concentration influences the reaction kinetics. At low photon flux, where surface hole concentrations are low, faster charge transfer was observed on photoelectrodes with low catalyst density compared to high catalyst density; at high photon flux and high applied potentials, where surface hole concentrations are moderate or high, slower surface charge recombination was afforded by low‐density catalysts. The results support that charge transfer between the light absorber and the catalyst is reversible; they reveal the unexpected benefits of low‐density catalyst loading in facilitating forward charge transfer for desired chemical reactions. It is implied that for practical solar water splitting devices, a suitable catalyst loading is important for maximized performance.

Liu, Tianying↗

Low Catalyst Loading Enhances Charge Accumulation for Photoelectrochemical Water Splitting

Abstract Solar water oxidation is a critical step in artificial photosynthesis. Successful completion of the process requires four holes and releases four protons. It depends on the consecutive accumulation of charges at the active site. While recent research has shown an obvious dependence of the reaction kinetics on the hole concentrations on the surface of heterogeneous (photo)electrodes, little is known about how the catalyst density impacts the reaction rate. Using atomically dispersed Ir catalysts on hematite, we report a study on how the interplay between the catalyst density and the surface hole concentration influences the reaction kinetics. At low photon flux, where surface hole concentrations are low, faster charge transfer was observed on photoelectrodes with low catalyst density compared to high catalyst density; at high photon flux and high applied potentials, where surface hole concentrations are moderate or high, slower surface charge recombination was afforded by low‐density catalysts. The results support that charge transfer between the light absorber and the catalyst is reversible; they reveal the unexpected benefits of low‐density catalyst loading in facilitating forward charge transfer for desired chemical reactions. It is implied that for practical solar water splitting devices, a suitable catalyst loading is important for maximized performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗