Search NASA⌕ Search

SEARCH · Search NASA

Results for “lapping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

NR-150 adhesive development

A polyimide precursor adhesive solution, code-named NR-056X, was developed. It reproducibly gives low void, high strength bond lines at both room temperature and 589K (600 F) using either titanium or graphite/polyimide composite adherends having 12.7 mm (1/2 in.) overlaps. Lap shear samples prepared using this adhesive and composite adherends based on graphite/NR-150B2 were shown to have a high degree of resistance to such adverse environments as air at 589K (600 F), high humidity, methyl ethyl ketone and jet fuel. Bond line toughness was illustrated by the complete resistance to cracking in the wedge-crack propagation test. The available evidence indicates that wide area composite to composite or composite to metal bonding should be feasible.

Blatz, P. S.↗

Preliminary bolted-joint data

Bolted-joint strength and failure modes for advanced graphite/polyimide composite laminates at 116K (-250 F), room temperature, and 589K (600 F) were determined to provide preliminary design data. The bolted-joint test setup for the low and elevated temperature tests is described. Test results are reported on a quasi-isotropic laminate of Celion 6000/PMR-15. Single bolt, double lap shear specimens were tested to obtain maximum joint strength and failure mode. The effect of joint geometry and temperature on joint strength and failure mode is presented.

Wichorek, G. R.↗

Planar scarf joints in composite repair

This study examined the effects of varying certain important geometric parameters on the stresses in an adhesive repair of a thin composite laminate. The repair, a planar scarf joint with a doubler, was studied using finite element methods at scarf angles of 6 deg and 12 deg, damage lengths between 2.5 mm and 25 mm and doubler overlaps between 10 mm and 40 mm. Finite element models also showed that significant stress peaks occur at the ends of the scarf joint adhesive, similar to shear lag phenomena in lap joints. A bending model of the planar scarf joint with a doubler, based on mechanics of materials theory, was also developed.

Adkins, D. W.↗

High temperature adhesives for bonding Kapton

Experimental polyimide resins have been developed and evaluated as potential high temperature adhesives for bonding Kapton polyimide film. Lap shear strengths of 'Kapton'/'Kapton' bonds were obtained as a function of test temperature, adherend thickness, and long term aging at 575K (575 F) in vacuum. Glass transition temperatures of the polyimide/'Kapton' bondlines were monitored by thermomechanical analysis.

Saint Clair, A. K.↗

A high volume cost efficient production macrostructuring process

The paper presents an experimentally developed surface macro-structuring process suitable for high volume production of silicon solar cells. The process lends itself easily to automation for high throughput to meet low-cost solar array goals. The tetrahedron structure observed is 0.5 - 12 micron high. The surface has minimal pitting with virtually no or very few undeveloped areas across the surface. This process has been developed for (100) oriented as cut silicon. Chemi-etched, hydrophobic and lapped surfaces were successfully texturized. A cost analysis as per Samics is presented.

Chitre, S. R.↗

LARC-13 polyimide adhesive bonding

The development of an addition-curing polyimide adhesive suitable for low pressure bonding without the generation of volatiles during cure is reported. LARC-13 is designed for bonding of polyimide matrix composites and of titanium to be used above 500 F, and is based on an oligomeric bis-nadimide which allows its processing at 50 psi or less, making it suitable for the bonding of fragile honeycomb sandwich structures. Few volatiles are evolved during its cure allowing large enclosed structures to be bonded, and it has high room and elevated temperature strengths and good strength retention after short terms up to 1100 F. LARC-13 was successfully used to bond the outer and inner skins of a polyimide/graphite wing shear panel for 500 F use, and for a short-term exposure up to 1100 F. Preparation of the adhesive, bonding, aging, and testing of lap shear and honeycomb samples are discussed.

Saint Clair, T. L.↗

Effects of plasma sheath on solar power satellite array

The structure of the plasma sheath and equilibrium voltage distribution of a high-power solar array governs various kinds of plasma-interaction phenomena and array losses. Sheath effects of a linearly-connected array are investigated for GEO. Although the array may be large, the thin-sheath-limit analysis may be invalid, necessitating numerical methods. Three-dimensional computer calculations show that potential barriers and over-lapping sheaths can occur, i.e., structures not predictable under the thin-sheath-limit analysis, but nevertheless controlling the distribution of plasma currents impacting on the array.

Parker, L. W.↗

Solar heating and hot water system installed at Municipal Building complex, Abbeville, South Carolina

Information on the solar energy system installed at the new municipal building for the City of Abbeville, SC is presented, including a description of solar energy system and buildings, lessons learned, and recommendations. The solar space heating system is a direct air heating system. The flat roof collector panel was sized to provide 75% of the heating requirement based on an average day in January. The collectors used are job-built with two layers of filon corrugated fiberglass FRP panels cross lapped make up the cover. The storage consists of a pit filled with washed 3/4 in - 1 1/2 in diameter crushed granite stone. The air handler includes the air handling mechanism, motorized dampers, air circulating blower, sensors, control relays and mode control unit. Solar heating of water is provided only those times when the hot air in the collector is exhausted to the outside.

Source record↗

High-temperature adhesives for bonding polyimide film

Experimental polyimide resins were developed and evaluated as potential high temperature adhesives for bonding Kapton polyimide film. Lap shear strengths of Kapton/Kapton bonds were obtained as a function of test temperature, adherend thickness, and long term aging at 575 K (575 F) in vacuum. Glass transition temperatures of the polyimide/"Kapton" bondlines were monitored by thermomechanical analysis.

St.clair, A. K.↗

Viscoelastic analysis of adhesively bonded joints

An adhesively bonded lap joint is analyzed by assuming that the adherends are elastic and the adhesive is linearly viscoelastic. After formulating the general problem a specific example for two identical adherends bonded through a three parameter viscoelastic solid adhesive is considered. The standard Laplace transform technique is used to solve the problem. The stress distribution in the adhesive layer is calculated for three different external loads, namely, membrane loading, bending, and transverse shear loading. The results indicate that the peak value of the normal stress in the adhesive is not only consistently higher than the corresponding shear stress but also decays slower.

Delale, F.↗

LARC-13 adhesive development

A LARC-13 type adhesive system was developed and property data obtained that demonstrated improved thermomechanical properties superior to base LARC-13 adhesive. An improved adhesive for 589 K (600 F) use was developed by physical or chemical modification of LARC-13. The adhesive was optimized for titanium and composite bonding, and a compatible surface preparation for titanium and composite substrates was identified. The data obtained with the improved adhesive system indicated it would meet the 589 K (600 F) properties desired for application on space shuttle components. Average titanium lap shear data were: (1) 21.1 MPa (3355 psi) at RT, (2) 13.0 MPa (1881 psi) at 600 F, and (3) 16.4 MPa (2335) after aging 125 hours at 600 F and tested at 600 F.

Hill, S. G.↗

Stress analysis of bonded plates and joints

The paper presents a general numerical method of solution to the transverse normal stress and longitudinal shear stress distributions in the adhesive layers of bonded stiffener plates, double lap joints, and strap joints, all of dissimilar orthotropic adherends. The bending deformations and the transverse shear deformations are included in the analytical model. The present influence of bending deformations of adherends on both the normal and shear stresses in adhesive layers is discussed in detail for practical cases.

Yuceoglu, U.↗

High temperature adhesives for bonding composites

Selection and evaluation of candidate adhesives for bonding composites are described. These are based on mechanical property tests (lap shear and flatwise tensile) and processibility. Consideration is given to composite-to-composite, composite-to-titanium, and honeycomb sandwich structures.

Progar, D. J.↗

Incorporation of metal ions into polyimides

The effects of the incorporation of metal ions into various polyimides on polyimide properties are investigated. Polyimide films derived from 3,3',4,4'-benzophenone tetracarboxylic acid dianhydride (BDTA) 3,3'-diaminobenzophenone (m,m'-DABP), 4,4'-diaminobenzophenone (p,p'-DABP) or 4,4'-oxydianiline were prepared with the concurrent addition of approximately 20 metals in a variety of forms. In general, it is found that the films derived from BDTA + p,p'-DABP were brittle and of poor quality, with brittle films also produced in most of the BDTA + m, m'-DABP polyimides regardless of whether the added metal was hydrate or anhydrous. Thermomechanical analysis, torsional braid analysis, thermal gravimetric analysis, infrared spectral analysis and isothermal studies on many of the polyimide films produced indicate that the softening temperature is generally increased upon the addition of metal ions, at the expense of thermal stability, while no changes in chemical functionality are observed. The best system studied in regard to polymer property enhancement appears to be tri(acetylacetonato)aluminum(III) added to the m, m'-DABP polyamide, which has been found to exhibit four times the lap shear strength of the polyimide alone.

Taylor, L. T.↗

Stresses in adhesively bonded joints: A closed form solution

The plane strain of adhesively bonded structures which consist of two different orthotropic adherents is considered. Assuming that the thicknesses of the adherends are constant and are small in relation to the lateral dimensions of the bonded region, the adherends are treated as plates. The transverse shear effects in the adherends and the in-plane normal strain in the adhesive are taken into account. The problem is reduced to a system of differential equations for the adhesive stresses which is solved in closed form. A single lap joint and a stiffened plate under various loading conditions are considered as examples. To verify the basic trend of the solutions obtained from the plate theory a sample problem is solved by using the finite element method and by treating the adherends and the adhesive as elastic continua. The plate theory not only predicts the correct trend for the adhesive stresses but also gives rather surprisingly accurate results.

Delale, F.↗

Addition polyimide end cap study

The characterization of addition polyimides with various end caps for adhesive applications at 120-250 C environments is discussed. Oligometric polyimides were prepared from 3,3',4,4'-benzophenone tetracarboxylic dianhydride and 3,3'-methylenedianiline which were end-capped with functionally reactive moities which cause crosslinking when the oligomers are heated to 200-400 C. The syntheses of the oligomers are outlined. The thermolysis of the oligomers was studied by differential scanning calorimetry and the resulting polymers were characterized by differential thermal analysis and adhesive performance. The adhesive data include lap shear strengths on titanium 6-4 adherends both before and after aging for 1000 hours at 121 C and/or 232 C.

St.clair, T. L.↗

Residual Silicone Detection

Both photoelectron emission and ellipsometry proved successful in detecting silicone contamination on unpainted and epoxy painted metal surfaces such as those of the external tank and the solid rocket booster. Great success was achieved using photoelectron emission (PEE). Panels were deliberately contaminated to controlled levels and then mapped with PEE to reveal the areas and levels that were contaminated. The panels were then tested with regard to adhesive properties. Tapes were bonded over the contaminated and uncontaminated regions and the peel force was measured, or the contaminated panels were bonded (with CPR 483 foam) to uncontaminated panels and made into lap shear specimens. Other panels were bonded and made into wedge specimens for hydrothermal stress endurance tests. Strong adhesion resulted if the PEE signal fell within an acceptance window, but was poor outside the acceptance window. A prototype instrument is being prepared which can automatically be scanned over the external liquid hydrogen tank and identify those regions that are contaminated and will cause bond degradation.

Smith, T.↗

Space fabrication demonstration system

The development effort on the composite beam cap fabricator was completed within cost and close to abbreviated goals. The design and analysis of flight weight primary and secondary beam builder structures proceeded satisfactorily but remains curtailed until further funding is made available to complete the work. The induction fastening effort remains within cost and schedule constraints. Tests of the LARC prototype induction welder is continuing in an instrumented test stand comprised of a Dumore drill press (air over oil feed for variable applied loads) and a dynamometer to measure actual welding loads. Continued testing shows that the interface screening must be well impregnated with resin to ensure proper flow when bonding graphite-acrylic lap shear samples. Specimens prepared from 0.030 inch thick graphite-polyethersulfone are also available for future induction fastening evaluation.

Source record↗