Search NASA⌕ Search

SEARCH · Search NASA

Results for “large deformations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Near Earth Asteroid Scout Solar Sail Thrust and Torque Model

The Near Earth Asteroid (NEA) Scout is a solar sail mission whose objective is to scout at least one Near Earth Asteroid to help prepare for human missions to Near Earth Asteroids. NEA Scout will launch as a secondary payload on the first SLS-Orion mission. NEA Scout will perform a small trim maneuver shortly after deploy from the spent SLS upper stage using a cold gas propulsion system, but from that point on will depend entirely on the solar sail for thrust. As such, it is important to accurately characterize the thrust of the sail in order to achieve mission success. Additionally, the solar sail creates a relatively large solar disturbance torque that must be mitigated. For early mission design studies a flat plate model of the solar sail with a fixed center of pressure was adequate, but as mission concepts and the sail design matured, greater fidelity was required. Here we discuss the progress to a three-dimensional sail model that includes the effects of tension and thermal deformation that has been derived from a large structural Finite Element Model (FEM) developed by the Langley Research Center. We have found that the deformed sail membrane affects torque relatively much more than thrust; a flat plate model could potentially model thrust well enough to close mission design studies, but a three-dimensional solar sail is essential to control system design. The three-dimensional solar sail model revealed that thermal deformations of unshielded booms would create unacceptably large solar disturbance torques. The original large FEM model was used in control and mission simulations, but was resulted in simulations with prohibitive run times. This led us to adapt the Generalized Sail Model (GSM) of Rios-Reyes. A design reference sail model has been baselined for NEA Scout and has been used to design the mission and control system for the sailcraft. Additionally, since NEA Scout uses reaction wheels for attitude pointing and control, the solar torque model is essentially to successfully design the NEA Scout momentum management control system. We have also updated the estimate of diffusivity used for the aluminized sail material based on optical testing of wrinkled sail material. The model presented here represents the current state of the art of NASA's ability to model solar sail thrust and torque.

Heaton, Andy↗
NASA NTRS2019

Wrinkle Ridges on Mercury and the Moon Within and Outside of Mascons

Found on all terrestrial planets, wrinkle ridges are anticlines formed by thrust faulting and folding resulting from crustal shortening. The MErcury Surface, Space Environment, Geochemistry, and Ranging (MESSENGER) spacecraft's orbital phase returned high resolution images and topographic data of the previously unimaged northern high latitudes of Mercury where there are large expanses of smooth plains deformed by wrinkle ridges. Concurrently, the Lunar Reconnaissance Orbiter (LRO) is obtaining high resolution images and topographic data covering lunar mare wrinkle ridges. These data allow quantitative comparison of the scale of wrinkle ridges in smooth plains volcanic units on Mercury with mare wrinkle ridges. We evaluate the topographic relief of 300 wrinkle ridges within and outside of mascon basins on the Moon and Mercury. Measured wrinkle ridges range from ~112 to 776 m in relief with a mean of ~350 m (median = ~340 m, n = 150) on Mercury and from ~47 to 678 m in relief with a mean of ~198 m (median = ~168 m, n = 150) on the Moon. Wrinkle ridges on Mercury thus are approximately twice as large in mean relief compared to their counterparts on the Moon. The larger scale of Mercury's wrinkle ridges suggests that their formation can be attributed, in part, to global contraction. As global contraction on the Moon is estimated to be an order of magnitude smaller than on Mercury, the smaller scale of lunar wrinkle ridges suggests they most likely form primarily by load induced subsidence of the mare basalt. Wrinkle ridges located in lunar mascon basins and in the Caloris mascon on Mercury are not statistically significantly different in relief than ridges in non-mascon regions, suggesting comparable levels of contractional strain. The fact that mascon basins do not host wrinkle ridges with greater structural relief relative to non-mascon units may indicate the critical role lithospheric thickness plays in controlling subsidence and contraction of thick volcanic sequences on the Moon and Mercury.

Global contraction↗
NASA NTRS2019

Wrinkle ridges on Mercury and the Moon within and outside of mascons

Found on all terrestrial planets, wrinkle ridges are anticlines formed by thrust faulting and folding resulting from crustal shortening. The MErcury Surface, Space Environment, Geochemistry, and Ranging (MESSENGER)spacecraft's orbital phase returned high resolution images and topographic data of the previously unimaged northern high latitudes of Mercury where there are large expanses of smooth plains deformed by wrinkle ridges. Concurrently, the Lunar Reconnaissance Orbiter (LRO) is obtaining high resolution images and topographic data covering lunar mare wrinkle ridges. These data allow quantitative comparison of the scale of wrinkle ridges in smooth plains volcanic units on Mercury with mare wrinkle ridges. We evaluate the topographic relief of 300 wrinkle ridges within and outside of mascon basins on the Moon and Mercury. Measured wrinkle ridges range from ~112 to 776 min relief with a mean of ~350m (median=~340m, n=150) on Mercury and from ~47 to 678 min relief with a mean of ~198 m (median=~168m, n=150) on the Moon. Wrinkle ridges on Mercury thus are approximately twice as large in mean relief compared to their counterparts on the Moon. The larger scale of Mercury's wrinkle ridges suggests that their formation can be attributed, in part, to global contraction. As global contraction on the Moon is estimated to be an order of magnitude smaller than on Mercury, the smaller scale of lunar wrinkle ridges suggests they most likely form primarily by load induced subsidence of the mare basalt. Wrinkle ridges located in lunar mascon basins and in the Caloris mascon on Mercury are not statistically significantly different in relief than ridges in non-mascon regions, suggesting comparable levels of contractional strain. The fact that mascon basins do not host wrinkle ridges with greater structural relief relative to non-mascon units may indicate the critical role lithospheric thickness plays in controlling subsidence and contraction of thick volcanic sequences on the Moon and Mercury.

Lisa S. Schleicher↗
NASA NTRSDate not supplied

A Solar Sail Shape Modeling Approach for Attitude Control Design and Analysis

Solar sails operating in the space environment experience deformations in sail shape that result in relatively large disturbance torques which dictate the required performance of the spacecraft attitude control and momentum management systems. These deformations are driven by thermal loads on the booms (due to uneven solar heating), manufacturing and assembly tolerances, and variations in membrane tension. The Solar Cruiser spacecraft utilizes a four-quadrant sail design with four 30-meter length booms and four triangular sail membranes, creating a square sail structure of >1600 m2. Medium-fidelity mesh models were developed based on a characteristic deformed shape. A series of parametric studies were conducted using this shape paradigm to determine worst-case deformed sail shapes which produce bounding disturbance torques. A large database of shapes was produced, and the forces and moments induced by each individual shape were calculated using a Rios-Reyes reduced order generalized sail model. Two were selected as reference worst-case shapes for the Solar Cruiser mission: one which produced the highest pitch/yaw root-sum-squared (RSS) torque, and one which produced the highest roll torque. The results showed that the worst-case shapes at high solar incidence angles induce significantly higher (2-10x) disturbance torques than an ideal, flat-plate sail. Even with considerable safety margins, assuming an ideal sail is unlikely to sufficiently bound the disturbances, which is critical when designing the attitude control system and sizing actuators. Accurate sail shape modeling methodologies should therefore be employed on future solar sail missions.

Solar Sail↗
NASA NTRSDate not supplied

A Solar Sail Shape Modeling Approach for Attitude Control Design and Analysis

Solar sails operating in the space environment experience deformations in sail shape that result in relatively large disturbance torques which dictate the required performance of the spacecraft attitude control and momentum management systems. These deformations are driven by thermal loads on the booms (due to uneven solar heating), manufacturing and assembly tolerances, and variations in membrane tension. The Solar Cruiser spacecraft utilizes a four-quadrant sail design with four 30-meter length booms and four triangular sail membranes, creating a square sail structure of >1600 m2. Medium-fidelity mesh models were developed based on a characteristic deformed shape. A series of parametric studies were conducted using this shape paradigm to determine worst-case deformed sail shapes which produce bounding disturbance torques. A large database of shapes was produced, and the forces and moments induced by each individual shape were calculated using a Rios-Reyes reduced order generalized sail model [1]. Two were selected as reference worst-case shapes for the Solar Cruiser mission: one which produced the highest pitch/yaw root-sum-squared (RSS) torque, and one which produced the highest roll torque. The results showed that the worst-case shapes at high solar incidence angles induce significantly higher (2-10x) disturbance torques than an ideal, flat-plate sail. Even with considerable safety margins, assuming an ideal sail is unlikely to sufficiently bound the disturbances, which is critical when designing the attitude control system and sizing actuators. Accurate sail shape modeling methodologies should therefore be employed on future solar sail missions. References [1] L. Rios-Reyes and D. J. Scheeres, “Generalized Model for Solar Sails,” Journal of Spacecraft and Rockets, Vol. 42, Jan. 2005, pp. 182–185, 10.2514/1.9054.

Solar Sail↗
NASA NTRS2000

Deformation and Flexibility Equations for Idealized ARIS Umbilicals, Under Planar End-Loading Conditions

The International Space Station (ISS) relies on the Active Rack Isolation System (ARIS) as the central component of an integrated, station-wide strategy to isolate microgravity space-science experiments. ARIS uses electromechanical actuators to isolate an International Standard Payload Rack (ISPR) from disturbances due to the motion of the ISS. Disturbances to microgravity experiments on ARIS-isolated racks are primarily transmitted via the ARIS power and vacuum umbilicals. Recent experimental tests indicate that these umbilicals resonate at frequencies outside the ARIS controller's bandwidth. at levels of potential concern for certain microgravity experiments. Reduction in the umbilical resonant frequencies could help to address this issue. This paper develops equations for the in-plane deflections and flexibilities of an idealized umbilical (thin, flexible, cantilever beam) under end-point, in-plane loading (inclined-force and moment). The effect of gravity is neglected due to the on:orbit application. The analysis assumes an initially straight. cantilevered umbilical with uniform cross-section. which undergoes large deflections with no plastic deformation, such that the umbilical terminus remains in a single quadrant and the umbilical slope changes monotonically. The analysis is applicable to the ARIS power and vacuum umbilicals. under the indicated assumptions.

Hampton, R. David↗
NASA NTRS2003

Deformation and Flexibility Equations for Idealized ARIS Umbilicals, Under Planar End-Loading Conditions

The International Space Station (ISS) relies on the Active Rack Isolation System (ARIS) as the central component of an integrated, station-wide strategy to isolate microgravity space-science experiments. ARIS uses electromechanical actuators to isolate an International Standard Payload Rack (ISPR) from disturbances due to the motion of the ISS. Disturbances to microgravity experiments on ARIS-isolated racks are primarily transmitted via the ARTS power and vacuum umbilicals. Recent experimental tests indicate that these umbilicals resonate at frequencies outside the ARIS controller's bandwidth, at levels of potential concern for certain microgravity experiments. Reduction in the umbilical resonant frequencies could help to address this issue. This report develops equations for the in-plane deflections and flexibilities of an idealized umbilical (thin, flexible, cantilever beam) under end-point, in-plane loading (inclined-force and moment). The effect of gravity is neglected due to the on-orbit application. The analysis assumes an initially straight, cantilevered umbilical with uniform cross-section, which undergoes large deflections with no plastic deformation, such that the umbilical terminus remains in a single quadrant and the umbilical slope changes monotonically. The analysis is applicable to the ARIS power and vacuum umbilicals, under the indicated assumptions.

Hampton, R. David↗
NASA NTRS2005

Deformation and Flexibility Equations for ARIS Umbilicals Idealized as Planar Elastica

The International Space Station relies on the active rack isolation system (ARIS) as the central component of an integrated, stationwide strategy to isolate microgravity space-science experiments. ARIS uses electromechanical actuators to isolate an international standard payload rack from disturbances due to the motion of the Space Station. Disturbances to microgravity experiments on ARIS isolated racks are transmitted primarily via the ARIS power and vacuum umbilicals. Experimental tests indicate that these umbilicals resonate at frequencies outside the ARIS controller s bandwidth at levels of potential concern for certain microgravity experiments. Reduction in the umbilical resonant frequencies could help to address this issue. This work documents the development and verification of equations for the in-plane deflections and flexibilities of an idealized umbilical (thin, flexible, inextensible, cantilever beam) under end-point, in-plane loading (inclined-force and moment). The effect of gravity is neglected due to the on-orbit application. The analysis assumes an initially curved (not necessarily circular), cantilevered umbilical with uniform cross-section, which undergoes large deflections with no plastic deformation, such that the umbilical slope changes monotonically. The treatment is applicable to the ARIS power and vacuum umbilicals under the indicated assumptions.

Hampton, R. David↗
NASA NTRS1978

Regional deformation of mare surfaces

The possible tectonic significance of large topographic irregularities within Mare Serenitatis is discussed, and the characteristics of sinuous rilles are considered as possible indicators of structural deformation. It is shown that most sinuous rilles have been structurally warped and that their slopes lie within the laminar flow range. The sinuous rilles may have been formed in the domain of turbulent flow, if the ratios of meander wavelength to channel width can be taken as indicators. Some surface tectonic deformation occurring before the broad uplift of the basin center is suggested by the surface topography and radar reflectors in the Mare Serenitatis.

Scott, D. H.↗
DOE OSTI2020

Implications of post-processing induced microstructural changes on the deformation and fracture response of additively manufactured Ti–6Al–4V

Ti–6Al–4V parts fabricated via electron beam melting (EBM) powder bed fusion are often subjected to hot isostatic pressing below the β-transus temperature to mitigate defects. During which the pressure aids in pore closure and the thermal exposure results in coarsening of α phase while retaining the columnar prior-β phase grain morphology present in the as-fabricated condition. The same post-processing treatment can also be carried out above β-transus temperature which is an effective way to modify both the grain morphology and the associated α textures. Here, the objective of this work is to correlate thermally induced microstructural changes to the deformation and fracture response of the EBM processed Ti–6Al–4V. To this end, we have carried out both sub-transus and super-transus heat-treatments of the as-fabricated material. The mechanical response of the as-fabricated and all heat-treated materials are characterized by in-situ tensile tests under a high-resolution digital optical microscope. This enabled us to capture large-scale panoramic images of the deforming microstructure, and overcome the trade-off between the image resolution and the field of view during in-situ experiments. The series of images captured throughout the imposed deformation are subsequently used to perform microstructure-based digital image correlation to measure microstructural-scale strains over a large area. The results of the in-situ tests together with detailed fractographic analyses are then used to elucidate how the heterogeneous deformation spanning over multiple microstructural length-scales, for example, at the scale of lamellae, colonies of lamellae and grain boundaries, affect the overall deformation and fracture response of the post-processed materials.

36 MATERIALS SCIENCE↗
NASA NTRS2001

Characterization of the electromechanical properties of EAP materials

Electroactive polymers (EAP) are an emerging class of actuation materials. Their large electrically induced strains (longitudinal or bending), low density, mechanical flexibility, and ease of processing offer advantages over traditional electroactive materials. However, before the capability of these materials can be exploited, their electrical and mechanical behavior must be properly quantified. Two general types of EAP can be identified. The first type is ionic EAP, which requires relatively low voltages (<10V) to achieve large bending deflections. This class usually needs to be hydrated and electrochemical reactions may occur. The second type is Electronic-EAP and it involves electrostrictive and/or Maxwell stresses. This type of materials requires large electric fields (>100MV/m) to achieve longitudinal deformations at the range from 4 - 360%. Some of the difficulties in characterizing EAP include: nonlinear properties, large compliance (large mismatch with metal electrodes), nonhomogeneity resulting from processing, etc. To support the need for reliable data, the authors are developing characterization techniques to quantify the electroactive responses and material properties of EAP materials. The emphasis of the current study is on addressing electromechanical issues related to the ion-exchange type EAP also known as IPMC. The analysis, experiments and test results are discussed in this paper.

actuators↗
DOE OSTI2022

In-situ synchrotron X-ray diffraction investigation on deformation behavior of Nb/NiTi composite during pre-straining process

The mechanisms responsible for deformation behavior in Nb/NiTi composite during pre-straining were investigated systematically using in-situ synchrotron X-ray diffraction, transmission electron microscopy and tensile test. It is shown that upon loading, the composite experiences elastic elongation and slight plastic deformation of B19', B2 and β-Nb phases, together with the forward stress-induced martensitic (SIM) transformation from B2 to B19'. Upon unloading, the deformation mechanisms of the composite mainly involve elastic recovery of B19', B2 and β-Nb phases, compression deformation of β-Nb phase and incomplete B19'→B2 reverse SIM transformation. In the tensile loading-unloading procedure, besides the inherent elastic deformation and SIM transformation, the (001) compound twins in B19' martensite can also be conducive to the elastic deformation occurring in B19'-phase of the composite. Therefore, this composite can exhibit a large recoverable strain after unloading owing to the elastic deformation, and the partially reversible and consecutive SIM transformation together with the (001) compound twins.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structural Design Variations in Beetle Elytra

Abstract Beetles typically use their protective wing coverings or elytra to shield their membranous hindwings from the environment. Elytra in some terrestrial species have evolved a greater protective role capable of shielding the organism from powerful antagonistic predators. The structure–function relationships of these biological composites identify how architectural and chemical variations of the cuticle are tuned to create light‐weight, impact resistant composites. Specifically, the elytral structures of a tree dwelling beetle capable of flight, Trypoxylus dichotomus , and a terrestrial beetle incapable of flight, Phloeodes diabolicus , are compared to understand how their varied environmental needs forged the elytra to facilitate fight or resist fatal predator strikes. Mechanical and microstructural analysis reveals P . diabolicus has a harder, stiffer elytra that incorporate through‐thickness fibers to resist greater mechanical stresses imposed by bending and puncture. Conversely, the elytra of T . dichotomus have a compliant structure with large voids that facilitates localized deformation. Variations in flexural strength and puncture resistance remain attributed to P . diabolicus possessing a thicker cuticle with a greater degree of cross‐linking and an increased amount of endocuticular layers. These findings may provide useful insight into the design and manufacturing of composite materials for use in light‐weight or energy‐absorbing applications.

Rivera, Jesus↗
DOE OSTI2021

Irradiation hardening and ductility loss of Eurofer97 steel variants after neutron irradiation to ITER-TBM relevant conditions

Ten Eurofer97 steel variants, produced by non-standard fabrication-processing routes and modified alloying chemistries, were studied by neutron irradiations in the high flux isotope reactor. The irradiations were performed to ITER-TBM relevant conditions of ~255–350 °C, 2.94–3.24 dpa. We quantified the irradiation-induced degradation of the steels using mechanical property tests. All the steels suffered from irradiation hardening, where a significant increase in Vickers microhardness and yield stress (σ YS ) occurred, accompanied with severe loss of tensile elongation. The extent of hardening was material dependent. For T irr = 300±30 °C, most steels showed σ YS increase in the range of ~30% to as high as ~66%, except for a low temperature tempered steel with σYS increase below 15%. Despite large losses in elongation, most failures were ductile. Significant post-necking ductility was retained with reduction in area (RA) between 65–75%, but <50% for low temperature tempered steels. The ultimate tensile stress to yield stress (σ UTS /σ YS ) ratios decreased significantly after irradiation, highlighting irradiation-induced strain hardening capacity reduction. No major effect of irradiation on the plastic instability stress (σ PIS ) and true fracture stress of the steels was observed. By comparing the tensile stresses in true stress units and with literature, the results suggest that RAFM steel designing should target materials with a large separation between σ PIS and σ YS , to ensure the materials can maintain large work hardening and uniform deformation capability after irradiation. The tensile data of the steels additionally revealed a compelling evidence of an inverse trend between the change in RA and increase in σ YS of the neutron irradiated Eurofer97 type steels.

36 MATERIALS SCIENCE↗
DOE OSTI2020

LoTToR: An Algorithm for Missing-Wedge Correction of the Low-Tilt Tomographic 3D Reconstruction of a Single-Molecule Structure

A single-molecule three-dimensional (3D) structure is essential for understanding the thermal vibrations and dynamics as well as the conformational changes during the chemical reaction of macromolecules. Individual-particle electron tomography (IPET) is an approach for obtaining a snap-shot 3D structure of an individual macromolecule particle by aligning the tilt series of electron tomographic (ET) images of a targeted particle through a focused iterative 3D reconstruction method. The method can reduce the influence on the 3D reconstruction from large-scale image distortion and deformation. Due to the mechanical tilt limitation, 3D reconstruction often contains missing-wedge artifacts, presented as elongation and an anisotropic resolution. Here, we report a post-processing method to correct the missing-wedge artifact. This low-tilt tomographic reconstruction (LoTToR) method contains a model-free iteration process under a set of constraints in real and reciprocal spaces. A proof of concept is conducted by using the LoTToR on a phantom, i.e., a simulated 3D reconstruction from a low-tilt series of images, including that within a tilt range of ±15°. The method is validated by using both negative-staining (NS) and cryo-electron tomography (cryo-ET) experimental data. A significantly reduced missing-wedge artifact verifies the capability of LoTToR, suggesting a new tool to support the future study of macromolecular dynamics, fluctuation and chemical activity from the viewpoint of single-molecule 3D structure determination.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Corrugation-driven symmetry breaking in magic-angle twisted bilayer graphene

Abstract The discovery of unconventional superconductivity in magic-angle twisted bilayer graphene (tBLG) supported the twist-angle-induced flat band structure predictions made a decade earlier. Numerous physical properties have since been linked to the interlayer twist angle using the flat band prediction as a guideline. However, some key observations like the nematic phase and striped charge order behind the superconductivity are missing in this initial model. Here we show that a thermodynamically stable large out-of-plane displacement, or corrugation of the bilayer, induced by the interlayer twist, demonstrates partially filled states of the flat band structure, accompanied by a broken symmetry, in the magic-angle regime and the presence of symmetry breaking associated with the superconductivity in tBLG. The distinction between low and high corrugation can also explain the observed evolution of the vibrational spectra of tBLG as a function of twist angle. Our observation that large out-of-plane deformation modes enable partial filling of states near the Fermi energy may lead to a strategy for offsetting the effects of disorder in the local twist angle, which suppresses unconventional superconductivity and correlated insulator behavior in magic-angle tBLG.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Impact of O4 future detections on the determination of the dense matter equations of state

Here, in view of the next LIGO-Virgo-KAGRA Observing period O4 (to start in Spring 2023), we address the question of the ability of the interferometers network to discriminate among different neutron stars equation of states better than what was possible with the observation of the binary neutron stars merger GW170817. We show that the observation of an event similar to GW170817 during O4 would allow us to resolve the dimensionless effective tidal deformability $\tilde{Λ}$ within an uncertainty 7 times better than the one obtained in O2. Thanks to the expected increase in sensitivities, we show that any GW170817-like single-event within a distance of 100 Mpc would imply significantly improved constraints of the neutron stars equations of state. We also illustrate the important impact of the noise in the analysis of the signal, showing how it can impact the effective tidal deformability probability density function for large signal-to-noise ratio.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Bayesian Calibration of Nuclear Graphite Property Models Accounting for Model Inadequacy and Impacts on Component Performance

Nuclear-grade structural graphite is extensively utilized in the core designs of various advanced nuclear reactors. In the reactor environment, graphite is subjected to prolonged exposure to extreme conditions, including high temperatures, radiation, and potentially molten salt and oxygen. Such exposure can induce several degradation mechanisms in graphite, including nonuniform volumetric strains caused by irradiation and thermal expansion, leading to stresses that may compromise the performance of graphite components. Assessing component integrity requires accurate models of graphite's thermomechanical response. This report documents the Bayesian calibration of thermomechanical properties for nuclear-grade graphite and their application to graphite component modeling and simulation using the Grizzly code. As part of this work, uncertainty-quantified models were developed for the elastic modulus, coefficient of thermal expansion, irradiation-induced dimensional change, and irradiation-induced creep for graphite grades IG-110, NBG-18, NBG-17, PCEA, and 2114. Using a hierarchical Bayesian approach, multiple experimental data sources were combined to develop Gaussian process models for the properties. Using the Kennedy O'Hagan framework, the uncertainties due to inadequacies in the model and the inherent spread in the experimental data were quantified for three different models. These uncertainty-quantified models, with a model-form correction, were subsequently applied to a coupled-physics simulation of representative graphite components, revealing that the uncertainties have a large impact on the components' deformation.

36 - MATERIALS SCIENCE↗