Search NASA⌕ Search

SEARCH · Search NASA

Results for “matrix sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Measurement of the top-quark mass in $\mathrm{t}\overline{\mathrm{t}}$ events with dilepton final states in pp collisions at $\sqrt{s}=7\ \mbox{TeV}$

The top-quark mass is measured in proton-proton collisions at sqrt(s) = 7 TeV using a data sample corresponding to an integrated luminosity of 5.0 inverse femtobarns collected by the CMS experiment at the LHC. The measurement is performed in the dilepton decay channel t t-bar to ell+ nu[ell] b, ell- anti-nu[ell] b-bar, where ell=e,mu. Candidate top-quark decays are selected by requiring two leptons, at least two jets, and imbalance in transverse momentum. The mass is reconstructed with an analytical matrix weighting technique using distributions derived from simulated samples. Using a maximum-likelihood fit, the top-quark mass is determined to be 172.5 +/- 0.4 (stat) +/- 1.5 (syst) GeV.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Phase transformations in a Cu−Cr alloy induced by high pressure torsion

Phase transformations induced by high pressure torsion (HPT) at room temperature in two samples of the Cu-0.86 at.% Cr alloy, pre-annealed at 550 °C and 1000 °C, were studied in order to obtain two different initial states for the HPT procedure. Observation of microstructure of the samples before HPT revealed that the sample annealed at 550 °C contained two types of Cr precipitates in the Cu matrix: large particles (size about 500 nm) and small ones (size about 70 nm). The sample annealed at 1000 °C showed only a little fraction of Cr precipitates (size about 2 μm). The subsequent HPT process resulted in the partial dissolution of Cr precipitates in the first sample and dissolution of Cr precipitates with simultaneous decomposition of the supersaturated solid solution in another. However, the resulting microstructure of the samples after HPT was very similar from the standpoint of grain size, phase composition, texture analysis and hardness measurements. - Highlights: • Cu−Cr alloy with two different initial states was deformed by HPT. • Phase transformations in the deformed materials were studied. • SEM, TEM and X-ray diffraction techniques were used for microstructure analysis. • HPT leads to formation the same microstructure independent of the initial state.

36 MATERIALS SCIENCE↗

Application of nanoindentation testing to study of the interfacial transition zone in steel fiber reinforced mortar

The characteristics of the profiles of elastic modulus and hardness of the steel fiber-matrix and fiber-matrix-aggregate interfacial zones in steel fiber reinforced mortars have been investigated by using nanoindentation and Scanning Electron Microscopy (SEM), where two sets of parameters, i.e. water/binder ratio and content of silica fume were considered. Different interfacial bond conditions in the interfacial transition zones (ITZ) are discussed. For sample without silica fume, efficient interfacial bonds across the steel fiber-matrix and fiber-matrix-aggregate interfaces are shown in low water/binder ratio mortar; while in high water/binder ratio mortar, due to the discontinuous bleeding voids underneath the fiber, the fiber-matrix bond is not very good. On the other hand, for sample with silica fume, the addition of 10% silica fume leads to no distinct presence of weak ITZ in the steel fiber-matrix interface; but the effect of the silica fume on the steel fiber-matrix-aggregate interfacial zone is not obvious due to voids in the vicinity of steel fiber.

36 MATERIALS SCIENCE↗

Melt rock components in KREEPy breccia 15205: Petrography and mineral chemistry of KREEP basalts and quartz-normative mare basalts

Many current models for the origin of lunar highland rocks feature as an essential component the assimilation of KREEPy material by primitive magmas parental to the Mg-rich suite and alkali suite plutonic rocks. Similar models have also been proposed for the origin of various mare basalt suites. However, any model which considers assimilation of KREEP an important petrologic process must sooner-or-later deal with the question: what is KREEP? Because pristine KREEP basalts are rare, and most known samples are small (e.g., 15382/15386), the geochemical variability of KREEP basalts is poorly known. Other KREEP compositions which are commonly used in these models include the hypothetical 'high-K KREEP' component of Warren and Wasson, which is derived from Apollo 14 soil data, and the 'superKREEP' quartz-monzodiorite 15405. Lunar breccia 15205 is a polymict regolith breccia that consists of approximately 20% KREEP basalt clasts and 20% quartz-normative basalt clasts in a KREEP-rich matrix. Bulk rock mixing calculations show that this sample comprises about 84% KREEP. The clasts range up to 1 cm in size, but most are considerably smaller. The primary aim is to characterize pristine KREEP basalts petrographically, to establish the range in chemical compositions of KREEP basalts, and to test models that were proposed for their origin. In addition, we may be able to extend the compositional range recognized in the quartz-normative basalt suite and cast some light on its origin as well. Preliminary whole rock geochemical data on the KREEP basalts are presented in a companion paper by M.M. Lindstrom and co-workers. Concentration is on petrography and mineral chemistry of these clasts, and the implications these data have for the origin of the different melt rock suites.

Shervais, John W.↗

Petrology of Apollo 15 black-and-white rocks 15445 and 15455 - Fragments of the Imbrium impact melt sheet

The paper describes two macroscopically similar black-and-white rocks, 15445 and 15455, which were collected from the rim of Spur Crater on the Apennine Front. The two Apollo 15 rocks are very similar in chemistry and clast population, but the matrix of 15455 is finer grained than that of 15445. The 15445 sample contains a lithic clast assemblage of plutonic/metamorphic spinel troctolite, troctolite, norite, and anorthosite, and its fine-grained vesicular black coherent matrix consists of a melt-bonded aggregate of small mineral clasts which are mainly olivine, plagioclase, and pink spinel. The two rocks are distinct from any other large samples from the Apollo 15 site. It is suggested that the rocks are samples of an impact melt sheet which forms a bedrock unit of the Apennine Front, and that this melt sheet did not form in a local small-scale event but was produced during the Imbrium impact event.

Ryder, G.↗

A Study on Recycled Polymers Recovered from Multilayer Plastic Packaging Films by Solvent–Targeted Recovery and Precipitation (STRAP)

Multilayer plastic film use increased in multiple packaging applications due to its versatility and overall increased performance over monolayer structures. However, the performance gains from multiple layers also make recycling difficult because they contain multiple polymers that can be immiscible and burdensome to traditional mechanical recycling operations. A possible solution is the solvent-targeted recovery and precipitation (STRAP) process, but the effect on the retrieved polymer is still unknown. Here, the STRAP process is applied to two different multilayer films and samples of recovered polymers are evaluated for physical, molecular, and thermal properties. Changes in the molecular weight are not significant, but differences in thermal properties are reported along with the coprecipitation of different polymers. Solvent retention in the polymer matrix from STRAP reduced the glass transition temperature of samples, but enhanced drying recovered it. Heavy metals, such as Cd, Cr, and Pb are not detected, indicating regulatory compliance for different applications.

36 MATERIALS SCIENCE↗

Development and Mechanical Properties of In Situ Al{sub 3}Ti-Reinforced Nanostructured AA6061 via Mechanical Alloying

Mechanical alloying (MA) was used to disperse 10 wt.% titanium powder in AA6061 powder. The resultant powder was degassed, and differential scanning calorimetry was performed to determine the temperature for formation of titanium aluminide (Al{sub 3}Ti). The MA powder was characterized by field emission scanning electron microscopy, x-ray diffraction (XRD) and transmission electron microscopy (TEM). Subsequently, the MA powder was consolidated by spark plasma sintering (SPS) at 500 °C under a pressure of 50 MPa. XRD and x-ray energy-dispersive spectroscopy of spark plasma sintered compact revealed in situ formation of Al{sub 3}Ti. TEM micrographs of spark plasma sintered sample exhibited Al nanograins (average size 50 nm) in the AA6061 matrix along with the dispersed Al{sub 3}Ti (average size 200 nm). Hardness, yield strength and compressive strength of the SPSed samples were also evaluated and compared with AA6061.

36 MATERIALS SCIENCE↗

Synchrotron radiation-based far-infrared spectroscopic ellipsometer with full Mueller-matrix capability

We developed far-IR spectroscopic ellipsometer at the U4IR beamline of the National Synchrotron Light Source in Brookhaven National Laboratory. This ellipsometer is able to measure both, rotating analyzer and full-Mueller matrix spectra using rotating retarders, and wire-grid linear polarizers. We utilize exceptional brightness of synchrotron radiation in the broad spectral range between about 20 and 4000 cm{sup -1}. Fourier-transform infrared (FT-IR) spectrometer is used for multi-wavelength data acquisition. The sample stage has temperature variation between 4.2 and 450 K, wide range of {theta}-2{theta} angular rotation, {chi} tilt angle adjustment, and X-Y-Z translation. A LabVIEW-based software controls the motors, sample temperature, and FT-IR spectrometer and also allows to run fully automated experiments with pre-programmed measurement schedules. Data analysis is based on Berreman's 4 Multiplication-Sign 4 propagation matrix formalism to calculate the Mueller matrix parameters of anisotropic samples with magnetic permeability {mu}{ne} 1. A nonlinear regression of the rotating analyzer ellipsometry and/or Mueller matrix (MM) spectra, which are usually acquired at variable angles of incidence and sample crystallographic orientations, allows extraction of dielectric constant and magnetic permeability tensors for bulk and thin-film samples. Applications of this ellipsometer setup for multiferroic and ferrimagnetic materials with {mu}{ne} 1 are illustrated with experimental results and simulations for TbMnO{sub 3} and Dy{sub 3}Fe{sub 5}O{sub 12} single crystals. We demonstrate how magnetic and electric dipoles, such as magnons and phonons, can be distinguished from a single MM measurement without adducing any modeling arguments. The parameters of magnetoelectric components of electromagnon excitations are determined using MM spectra of TbMnO{sub 3}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High sensitivity measurement of femtogram-level 238 Pu by thermal ionization mass spectrometry with correction of background 238 U

Low-concentration plutonium isotopic measurements provide a valuable fingerprint to identify possible material origins in the context of environmental contamination monitoring, environmental tracing, nuclear safeguards, nuclear forensics, and treaty monitoring. Thermal ionization mass spectrometry (TIMS) has long been recognized as one of the most sensitive techniques for plutonium isotopic measurement, but has not generally been utilized for 238 Pu determination, especially at low concentrations, due to an isobaric interference from 238 U, prevalent as background. Here, this work demonstrates a new analytical technique for correction of background 238 U from the 238 Pu counts collected during a TIMS analysis. The technique takes advantage of the higher ionization temperature of U relative to Pu and uses a 235 U tracer added after plutonium purification chemistry for 238 U semi-quantitative determination. This technique has been successfully applied to the determination of 238 Pu concentration and the 238 Pu/ 239 Pu ratio in sample types including single-isotope standards, isotopic certified reference materials, matrix-containing environmental reference materials, and simulated nuclear detonation debris. The results have been directly compared on a sample-by-sample basis to alpha spectrometry results. The detection limit by this new technique is 0.23 fg 238 Pu, which was previously unachievable by mass spectrometry and is possible in around 1 h of analysis time post-chemistry compared to weeks of required counting time by alpha spectrometry (at the same atom amount). We also present original, high precision data for Pu isotope concentrations in IAEA-384, Fangataufa Sediment, including 242 Pu results for the first time. The new technique allows measurement of a key isotope, 238 Pu, that was previously not measured in small environmental or nuclear forensics collections.

238Pu↗

Microstructural evolution during solution treatment of Co-Cr-Mo-C biocompatible alloys

Three different Co-Cr-Mo-C alloys conforming to ASTM F75 standard were poured in an industrial environment and subjected to a conventional solution treatment at 1225 Degree-Sign C for several time intervals. The microstructural changes and transformations were studied in each case in order to evaluate the way in which treatment time influences the secondary phase fraction and clarify the microstructural changes that could occur. To assess how treatment time affects microstructure, optical microscopy and image analyzer software, scanning electron microscopy and energy dispersion spectrometry analysis were employed. The main phases detected in the as-cast state were: {sigma}-phase, M{sub 6}C, and M{sub 23}C{sub 6} carbides. The latter presented two different morphologies, blocky type and lamellar type. Despite being considered the most detrimental feature to mechanical properties, {sigma}-phase and lamellar carbides dissolution took place in the early stages of solution treatment. M{sub 23}C{sub 6} carbides featured two different behaviors. In the alloy obtained by melting an appropriate quantity of alloyed commercial materials, a decrease in size, spheroidization and transformation into M{sub 6}C carbides were simultaneously observed. In the commercial ASTM F75 alloy, in turn, despite being the same phase, only a marked decrease in precipitates size was noticed. These different behaviors could be ascribed to the initial presence of other phases in the alloy obtained from alloyed materials, such as {sigma}-phase and 'pearlitic' carbides, or to the initial precipitate size which was much larger in the first than in the commercial ASTM F75 alloy studied. M{sub 6}C carbides dissolved directly in the matrix as they could not be detected in samples solution-treated for 15 min. - Highlights: Black-Right-Pointing-Pointer Three different Co-Cr-Mo alloys were poured under an industrial environment. Black-Right-Pointing-Pointer Transformation of existing phases followed during conventional solution treatment. Black-Right-Pointing-Pointer In as-cast/treated samples, phases were identified by color metallography, SEM and EDS. Black-Right-Pointing-Pointer M{sub 23}C{sub 6} {yields} M{sub 6}C transformation was corroborated by SEM and EDS analysis. Black-Right-Pointing-Pointer Carbide spheroidization was also detected prior a noticeably carbide size decreasing.

36 MATERIALS SCIENCE↗

Magnetocaloric effect in amorphous and partially crystallized Fe{sub 40}Ni{sub 38}Mo{sub 4}B{sub 18} alloys

A study of magnetocaloric effect in amorphous and partially crystallized Fe{sub 40}Ni{sub 38}Mo{sub 4}B{sub 18} alloys is reported. Amorphous Fe{sub 40}Ni{sub 38}Mo{sub 4}B{sub 18}, near its magnetic ordering temperature (600 K) showed a magnetic entropy change ΔS{sub M} of 1.1 J/KgK and a relative cooling power of 36 J/Kg in a field change of 10 kOe. Amorphous samples were partially crystallized by annealing at 700 K at different time intervals. Partially crystallized samples showed two distinct magnetic ordering temperature, one corresponding to the precipitated FeNi nanocrystals and the other one corresponding to the boron rich amorphous matrix. Magnetic ordering temperature of the residual amorphous matrix got shifted to the lower temperatures on increasing the annealing duration. Partially crystallised samples showed a magnetic entropy change of about 0.27 J/kgK near the magnetic ordering temperature of the amorphous matrix (540 K) in a field change of 10 kOe. The decrease in ΔS{sub M} on partial crystallisation is attributed to the biphasic magnetic nature of the sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Epoxy resin reinforced with carbonized chicken feathers: An innovative composite material with sustainable potentials

Here, this article explores a novel method for enhancing the mechanical properties of epoxy resin composites by incorporating carbonized chicken feathers as a filler material. The fabrication process involves carbonizing chicken feathers at 600°C and incorporating 5-10 wt% of the fillers into an epoxy matrix. The composites showed enhanced mechanical properties and samples containing 10 wt% filler exhibit the best properties. The performance corresponds to 49% increase in tensile strength, 16% rise in Young’s modulus, 40% improvement in flexural modulus, and 57% in flexural strength. X-ray diffraction and scanning electron microscopy with energy dispersive spectroscopy were employed to characterize the filler. This characterization provides valuable insights into the structure and chemical composition of the pulverized carbonized chicken feathers that contributed to the attained improvement in composites’ properties. Microstructural examination of the developed composite under scanning electron microscope also provides insights into matrix-filler interface and dispersion of the fillers within the composite matrix. The study not only highlights the unique combination of carbonized feathers’ inherent strength and compatibility with the epoxy matrix but also underscores the eco-friendly nature of utilizing agricultural waste. The findings suggest promising applications in industries demanding lightweight, high-strength materials, which can contribute to sustainable engineering solutions.

36 MATERIALS SCIENCE↗

Gas tungsten arc welding and friction stir welding of ultrafine grained AISI 304L stainless steel: Microstructural and mechanical behavior characterization

In the present study, an ultrafine grained (UFG) AISI 304L stainless steel with the average grain size of 650 nm was successfully welded by both gas tungsten arc welding (GTAW) and friction stir welding (FSW). GTAW was applied without any filler metal. FSW was also performed at a constant rotational speed of 630 rpm and different welding speeds from 20 to 80 mm/min. Microstructural characterization was carried out by High Resolution Scanning Electron Microscopy (HRSEM) with Electron Backscattered Diffraction (EBSD) and Transmission Electron Microscopy (TEM). Nanoindentation, microhardness measurements and tensile tests were also performed to study the mechanical properties of the base metal and weldments. The results showed that the solidification mode in the GTAW welded sample is FA (ferrite–austenite) type with the microstructure consisting of an austenite matrix embedded with lath type and skeletal type ferrite. The nugget zone microstructure in the FSW welded samples consisted of equiaxed dynamically recrystallized austenite grains with some amount of elongated delta ferrite. Sigma phase precipitates were formed in the region ahead the rotating tool during the heating cycle of FSW, which were finally fragmented into nanometric particles and distributed in the weld nugget. Also there is a high possibility that the existing delta ferrite in the microstructure rapidly transforms into sigma phase particles during the short thermal cycle of FSW. These suggest that high strain and deformation during FSW can promote sigma phase formation. The final austenite grain size in the nugget zone was found to decrease with increasing Zener–Hollomon parameter, which was obtained quantitatively by measuring the peak temperature, calculating the strain rate during FSW and exact examination of hot deformation activation energy by considering the actual grain size before the occurrence of dynamic recrystallization. Mechanical properties observations showed that the welding efficiency of the FSW welded sample is around 70%, which is more than 20% higher than the GTAW welded sample. - Highlights: • Microstructure and mechanical properties of UFG 304L stainless steel were studied during GTAW and FSW. • Sigma phase formation mechanism was studied during FSW of 304L stainless steel. • THERMOCALC analysis was performed to obtain possible formation temperatures for sigma phase. • Nano-mechanical twins were found in the TMAZ region.

36 MATERIALS SCIENCE↗

Improved Irradiation Performance of Uranium-Molybdenum/Aluminum Dispersion Fuel by Silicon Addition in Aluminum

Uranium-molybdenum fuel particle dispersion in aluminum is a form of fuel under development for conversion of high-power research and test reactors from highly enriched to low-enriched uranium in the U.S. Global Threat Reduction Initiative program (also known as the Reduced Enrichment for Research and Test Reactors program). Extensive irradiation tests have been conducted to find a solution for problems caused by interaction layer growth and pore formation between U-Mo and Al. Adding a small amount of Si (up to [approximately]5 wt%) in the Al matrix was one of the proposed remedies. The effect of silicon addition in the Al matrix was examined using irradiation test results by comparing side-by-side samples with different Si additions. Interaction layer growth was progressively reduced with increasing Si addition to the matrix Al, up to 4.8 wt%. The Si addition also appeared to delay pore formation and growth between the U-Mo and Al.

99 GENERAL AND MISCELLANEOUS↗

Effect of fiber spacing on interfacial damage in a metal matrix composite

The nature and the location of cracking in a Ti-V-Cr-Al-Sn/SiC composite (Ti-15V-3Cr-3Al-3Sn, in wt pct, reinforced by 33 vol pct of continuous unidirectional SCS-6SiC fibers) before and after unconstrained thermal cycling were investigated. The material was subjected to 10,000 thermal cycles between 300 and 550 C and samples were examined for cracks in the fiber, the matrix, and the fiber-matrix interface, using a back-scattered SEM. The Ti-based metal matrix composite was found to have a substantial amount of interfacial damage in the form of radial cracks, which formed first in the C-rich coating of the SiC fiber and then in the fiber-matrix reaction zone. The cracking was related to the fiber distribution, with consistently more cracking found between the more closely-spaced fibers within a given row, and more radial cracking in the outside fiber rows.

Mackay, Rebecca A.↗

Scattering Matrix Determination in Crystalline Materials from 4D Scanning Transmission Electron Microscopy at a Single Defocus Value

Recent work has revived interest in the scattering matrix formulation of electron scattering in transmission electron microscopy as a stepping stone toward atomic-resolution structure determination in the presence of multiple scattering. Here, we discuss ways of visualizing the scattering matrix that make its properties clear. Through a simulation-based case study incorporating shot noise, we shown how regularizing on this continuity enables the scattering matrix to be reconstructed from 4D scanning transmission electron microscopy (STEM) measurements from a single defocus value. Intriguingly, for crystalline samples, this process also yields the sample thickness to nanometer accuracy with no a priori knowledge about the sample structure. The reconstruction quality is gauged by using the reconstructed scattering matrix to simulate STEM images at defocus values different from that of the data from which it was reconstructed.

36 MATERIALS SCIENCE↗

Fast matrix algebra for Bayesian model calibration

In Bayesian model calibration, evaluation of the likelihood function usually involves finding the inverse and determinant of a covariance matrix. When Markov Chain Monte Carlo (MCMC) methods are used to sample from the posterior, hundreds of thousands of likelihood evaluations may be required. In this paper, we demonstrate that the structure of the covariance matrix can be exploited, leading to substantial time savings in practice. Here, we also derive two simple equations for approximating the inverse of the covariance matrix in this setting, which can be computed in near-quadratic time. The practical implications of these strategies are demonstrated using a simple numerical case study and the "quack" R package. For a covariance matrix with 1000 rows, application of these strategies for a million likelihood evaluations leads to a speedup of roughly 4000 compared to the naive implementation

97 MATHEMATICS AND COMPUTING↗

Shape stabilised phase change materials (SSPCMs): High density polyethylene and hydrocarbon waxes

Shape stabilised phase change materials (SSPCMs) based on high density polyethylene (HDPE) with high (HPW, T{sub m}=56-58 °C) and low (L-PW, T{sub m}=18-23 °C) melting point waxes were prepared by melt-mixing in a twin-screw extruder and their potential in latent heat thermal energy storage (LHTES) applications for housing assessed. The structure and morphology of these blends were investigated by scanning electron microscopy (SEM). Both H-PW and L-PW were uniformly distributed throughout the HDPE matrix. The melting point and latent heat of the SSPCMs were determined by differential scanning calorimetry (DSC). The results demonstrated that both H-PW and L-PW have a plasticisation effect on the HDPE matrix. The tensile and flexural properties of the samples were measured at room temperature (RT, 20±2 °C) and 70 °C, respectively. All mechanical properties of HDPE/H-PW and HDPE/L-PW blends decreased from RT to 70 °C. In all instances at RT, modulus and stress, irrespective of the mode of deformation was greater for the HDPE/H-PW blends. However, at 70 °C, there was no significant difference in mechanical properties between the HDPE/H-PW and HDPE/L-PW blends.

36 MATERIALS SCIENCE↗