SEARCH · Search NASA

Results for “sputtering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Growth and micro structural studies on Yittria Stabilized Zirconia (YSZ) and Strontium Titanate (STO) buffer layers

Microstructure of Yittria Stabilized Zirconia (YSZ) and Strontium Titanate (STO) of radio frequency magnetron sputtered buffer layers was studied at various sputtering conditions on Si (100), Sapphire and LaAlO3 (100) substrates. The effect of substrate temperatures up to 800 C and sputtering gas pressures in the range of 50 mTorr. of growth conditions was studied. The buffer layers of YSZ and STO showed a strong tendency for columnar growth was observed above 15 mTorr sputtering gas pressure and at high substrate temperatures. Post annealing of these films in oxygen atmosphere reduced the oxygen deficiency and strain generated during growth of the films. Strong c-axis oriented superconducting YBa2Cu3O7-x (YBCO) thin films were obtained on these buffer layers using pulsed laser ablation technique. YBCO films deposited on multilayers of YSZ and STO were shown to have better superconducting properties.

Srinivas, S.↗

NASA NTRS1995

Interstellar grains in elliptical galaxies

We consider the evolution and heating of dust embedded in the hot interstellar medium of isolated elliptical galaxies. We first construct a new set of galaxy models spanning a decade in luminosity which we use to study the evolution of dust as it is ejected by stellar sources, merges and flows with the interstellar gas, and is sputtered away due to the presence of the hot gas. We find that although grains can flow a considerable distance from the parent star in some cases before being sputtering away, the grain size distribution at a given location is accurately determined by assuming in situ sputtering of dust grains as they are ejected by the parent star. We find that dust heating is dominated by absorption of ambient starlight. Heating due to collisions with energetic electrons in the hot gas and absorption of thermal X-rays is smaller by orders of magnitude. We also find that for the largest galaxy considered (L(sub B) approximately 10 (exp 11) solar luminosity) the energy lost from the hot gas due to electronic collisions with the dust is about an order of magnitude less than that lost due to thermal emission in X-rays. The gas in smaller galaxies loses even less of its energy via heating of grains. In deriving this result, we find that the inclusion of grain sputtering is a crucial ingredient of the calculation. The presence of dust grains is therefore energetically unimportant for elliptical galaxy cooling flow models.

Tsai, John C.↗

NASA NTRS1999

An X-Ray Study of Grain Evolution behind Non-Radiative Shock

We model the dynamics, the destruction by sputtering, and the infrared (IR) emission from collisionally heated dust grains in fast (>/= 400 km s(exp -1)) astrophysical shocks in order to develop IR diagnostics for the destruction of grains in these environments. The calculations take into account the feedback from sputtering and IR emission on the gas-phase abundances, the cooling, and the ionization and thermal structure of the shock. Sputtering changes the initial grain size distribution, creating a deficiency of small (radius <50 A) grains compared to their preshock abundances. The altered grain size distribution depends on shock velocity and the density of the interstellar medium. Dust particles with sizes below approximately equal 300 A are stochastically heated, undergo temperature fluctuations, and radiate an excess of near-infrared emission (i </= 40 (micron)meter) over that expected for grains in thermal equilibrium. This near-infrared excess is a measure of the abundance of small grains and therefore a powerful diagnostic for the amount of destruction the grains were subjected to in the shock. We present here IR spectra from collisionally heated dust for a variety of shocks, and depict the changes in the spectra as a function of postshock column density. Our studies compliment those of Vancura et at. that examined the effects of the release of the sputtered refractory elements on the ultraviolet and X-ray emission. Multiwavelength observations at X-ray, Ultraviolet (UV), and IR wavelengths are therefore essential in piecing together a comprehensive picture of the physics of grain destruction in fast astrophysical shocks.

Vancura, Olaf↗

NASA NTRS2001

ISS And Space Environment Interactions Without Operating Plasma Contactor

The International Space Station (ISS) will be the largest, highest power spacecraft placed in orbit. Because of this the design of the electrical power system diverged markedly from previous systems. The solar arrays will operate at 160 V and the power distribution voltage will be 120 V. The structure is grounded to the negative side of the solar arrays so under the right circumstances it is possible to drive the ISS potential very negative. A plasma contactor has been added to the ISS to provide control of the ISS structure potential relative to the ambient plasma. The ISS requirement is that the ISS structure not be greater than 40 V positive or negative of local plasma. What are the ramifications of operating large structures with such high voltage power systems? The application of a plasma contactor on ISS controls the potential between the structure and the local plasma, preventing degrading effects. It is conceivable that there can be situations where the plasma contactor might be non-functional. This might be due to lack of power, the need to turn it off during some of the build-up sequences, the loss of functionality for both plasma contactors before a replacement can be installed, similar circumstances. A study was undertaken to understand how important it is to have the contactor functioning and how long it might be off before unacceptable degradation to ISS could occur. The details of interaction effects on spacecraft have not been addressed until driven by design. This was true for ISS. If the structure is allowed to float highly negative impinging ions can sputter exposed conductors which can degrade the primary surface and also generate contamination due to the sputtered material. Arcing has been known to occur on solar arrays that float negative of the ambient plasma. This can also generate electromagnetic interference and voltage transients. Much of the ISS structure and pressure module surfaces exposed to space is anodized aluminum. The anodization thickness is very thin to provide the required solar absorptance and emittance. For conditions where ISS structure can charge negative a large percentage of the array voltage, the dielectric strength of this layer is low, and dielectric breakdown (arcing) can occur. The energy stored capacitively in the structure can be delivered to the arc. The mechanisms by which this energy is delivered and how much of the energy is available hasn't been fully quantified. Questions have been raised regarding the possibility of whether a sustained arc might result due to current collected by the solar arrays from local plasma. It was postulated that even if dielectric breakdown didn't occur, impacts due to micrometeoroids and space debris could penetrate thin layers of dielectric on ISS and initiate an arc due to the coupling provided by the dense local plasma produced by the impact. This was proven in experiments conducted jointly by MSFC and Auburn University. A target chamber with a simulated ionospheric plasma and a biased, anodized aluminum plate and a 1-microfarad capacitor was used. The plate was then impacted by 75-micron particles accelerated to orbital velocity. Arc discharges were sustained for higher voltages but a threshold appears below which no discharge was initiated. Most items without an exposed power system will float electrically near the local plasma potential. This is true of the Space Shuttle, an Astronaut on EVA, and similar items. The structure of ISS might be at a large negative voltage. Therefore, capacitively stored energy can be transferred during docking, installing external boxes and equipment and Astronaut contact with ISS structure. The circumstances of when this can happen and the resulting effects are evaluated in this study. Also, a crewmember on EVA might be in the vicinity of an arc. All safety aspects of such an encounter including charging, molten particles from the arc site and EMI have been evaluated. This paper will report on the total results of this study focussed on the 4A configuration, scheduled to be complete in November, 2000. Interactions such as arcing, debris induced arcs, sustained arcs, sputtering, contamination from sputtering and arcing, docking interactions and Astronaut safety issues will all be addressed.

Carruth, M. R., Jr.↗

NASA NTRS2002

Optical Properties of Thin Film Molecular Mixtures

Thin films composed of molecular mixtures of metal and dielectric are being considered for use as solar selective coatings for a variety of space power applications. By controlling the degree of molecular mixing, the solar selective coatings can be tailored to have the combined properties of high solar absorptance, alpha, and low infrared emittance, epsilon. On orbit, these combined properties would simultaneously maximize the amount of solar energy captured by the coating and minimize the amount of thermal energy radiated. Mini-satellites equipped with solar collectors coated with these cermet coatings may utilize the captured heat energy to power a heat engine to generate electricity, or to power a thermal bus that directs heat to remote regions of the spacecraft. Early work in this area identified the theoretical boundary conditions needed to operate a Carnot cycle in space, including the need for a solar concentrator, a solar selective coating at the heat inlet of the engine, and a radiator. A solar concentrator that can concentrate sunlight by a factor of 100 is ideal. At lower values, the temperature of the solar absorbing surface becomes too low for efficient heat engine operation, and at higher values, cavity type heat receivers become attractive. In designing the solar selective coating, the wavelength region yielding high solar absorptance must be separated from the wavelength region yielding low infrared emittance by establishing a sharp transition in optical properties. In particular, a sharp transition in reflectance is desired in the infrared to achieve the desired optical performance. For a heat engine operating at 450C, a sharp transition at 1.8 micrometers is desired. The radiator completes the heat flow through the Carnot cycle. Additional work has been done supporting the use of molecular mixtures for terrestrial applications. Sputter deposition provides a means to apply coatings to the tubes that carry a working fluid at the focus of trough-style collectors. Sputtering offers considerable flexibility in coating conditions, including a wide variety of metal and dielectric targets. Coating designs range from simple two or three layer coatings to complex coatings that are purposely graded to be metal-rich at their base and oxide-rich at their surface in order to yield the desired solar selective properties. In these cermet coatings, molecular islands of metal are thought to be embedded in a three dimensional matrix of dielectric. Recent work has identified the use of custom made ion beam sputter deposition targets to produce coatings containing molecular mixtures of metal and dielectric. The targets are cylindrical and the surface consists of a gradually changing composition of metal and dielectric. Rotating the cylinder under the beam during ion beam sputter deposition yields a coating that is a molecular mixture of metal and dielectric, with the composition changing through the thickness of the coating. The optical properties of these coatings are not only dependent on their thickness and chemical composition, but are also dependent on the extent of the through thickness gradient established during deposition. This paper presents a summary of the optical properties of several thin film molecular mixtures designed as solar selective coatings. Optical performance is first identified as a function of wavelength, from the ultraviolet to the visible and infrared. Coating composition, thickness, and gradient from metal to dielectric also play an important role. Additional work for future activities is also identified.

Jaworske, Donald A.↗

NASA NTRS2003

Proposal for Testing and Validation of Vacuum Ultra-Violet Atomic Laser-Induced Fluorescence as a Method to Analyze Carbon Grid Erosion in Ion Thrusters

Previous investigation under award NAG3-25 10 sought to determine the best method of LIF to determine the carbon density in a thruster plume. Initial reports from other groups were ambiguous as to the number of carbon clusters that might be present in the plume of a thruster. Carbon clusters would certainly affect the ability to LIF; if they were the dominant species, then perhaps the LIF method should target clusters. The results of quadrupole mass spectroscopy on sputtered carbon determined that minimal numbers of clusters were sputtered from graphite under impact from keV Krypton. There were some investigations in the keV range by other groups that hinted at clusters, but at the time the proposal was presented to NASA, there was no data from low-energy sputtering available. Thus, the proposal sought to develop a method to characterize the population only of atoms sputtered from a graphite target in a test cell. Most of the ground work had been established by the previous two years of investigation. The proposal covering 2003 sought to develop an anti-Stokes Raman shifting cell to generate VUW light and test this cell on two different laser systems, ArF and YAG- pumped dye. The second goal was to measure the lowest detectable amounts of carbon atoms by 156.1 nm and 165.7 nm LIF. If equipment was functioning properly, it was expected that these goals would be met easily during the timeframe of the proposal, and that is the reason only modest funding was requested. The PI was only funded at half- time by Glenn during the summer months. All other work time was paid for by Whitworth College. The college also funded a student, Charles Shawley, who worked on the project during the spring.

Stevens, Richard↗

NASA NTRS2006

Material Interactions with Solar Wind Ion Environments

Solar wind composition is dominated by hydrogen (approx.96%) and helium (approx.3 to 4%) with a minor fraction (less than or equal to 1%) of heavy ions. Hydrogen (helium) ions impact spacecraft surfaces with energies from 0.5 to 5 keV (1.8 to 21 keV) due to variations in solar wind velocity from 300 km/s to 1000 km/sec with extremes of a few 10 s keV during periods of extremely high solar wind velocity exceeding 1000 km/sec. Mean impact energies are typically on the order of approximately 1 keV and 4 keV for hydrogen ions and helium ions, respectively. These energies are typically of the peak of the energy dependent light ion sputter yields for hydrogen and helium on many metals. In addition, light ions with kilovolt energies have been shown to produce blister (or exfoliation) damage to metal surfaces due to formation of high pressure gas bubbles within the materials when exposed to ion fluences on the order of 10(exp 16 to (10(exp 17 ions/sq cm. A number of spacecraft designs for current and future missions include gossamer polymer structures with thin metallic reflection coatings to shield instruments from the Sun or solar sail propulsion systems for use in a variety of locations in the inner solar system from 0.5 to 1 AU. In addition, there is interest in designing spacecraft for solar physics missions requiring operations as close to the Sun as 0.16 to 0.2 AU. Integrity of the metallic coatings is critical in many of these applications since degradation will result in modification of material thermal properties or exposure of polymers to solar UV photons which can compromise mission requirements. This paper will evaluate the relative contributions of sputtering and blister formation to material degradation in solar wind environments over a range of radial distances from the Sun to demonstrate where solar wind environments become important for materials selection. We will first review the physics and results from laboratory measurements of light ion sputtering, blistering, and exfoliation of metallic surfaces to establish the order of magnitude ion fluence required for significant surface damage. Solar wind ion fluence environments will then be evaluated due to variations in solar wind conditions as a function of solar cycle for varying distances from the Sun using models for radial variations in solar wind ion number density, temperature, and velocity to determine where sputtering and blistering is most likely to be an issue. Finally, ion fluence statistics for varying radial distances from the Sun will be shown to establish the mission duration and radial distances from the Sun where missions will encounter sufficient ion fluence to exhibit damage to metallic surfaces.

Minow, Joseph I.↗

NASA NTRS2009

Sources of Sodium in the Lunar Exosphere: Modeling Using Ground-Based Observations of Sodium Emission and Spacecraft Data of the Plasma

Observations of the equatorial lunar sodium emission are examined to quantify the effect of precipitating ions on source rates for the Moon's exospheric volatile species. Using a model of exospheric sodium transport under lunar gravity forces, the measured emission intensity is normalized to a constant lunar phase angle to minimize the effect of different viewing geometries. Daily averages of the solar Lyman alpha flux and ion flux are used as the input variables for photon-stimulated desorption (PSD) and ion sputtering, respectively, while impact vaporization due to the micrometeoritic influx is assumed constant. Additionally, a proxy term proportional to both the Lyman alpha and to the ion flux is introduced to assess the importance of ion-enhanced diffusion and/or chemical sputtering. The combination of particle transport and constrained regression models demonstrates that, assuming sputtering yields that are typical of protons incident on lunar soils, the primary effect of ion impact on the surface of the Moon is not direct sputtering but rather an enhancement of the PSD efficiency. It is inferred that the ion-induced effects must double the PSD efficiency for flux typical of the solar wind at 1 AU. The enhancement in relative efficiency of PSD due to the bombardment of the lunar surface by the plasma sheet ions during passages through the Earth's magnetotail is shown to be approximately two times higher than when it is due to solar wind ions. This leads to the conclusion that the priming of the surface is more efficiently carried out by the energetic plasma sheet ions.

Sarantos, Menelaos↗

NASA NTRS2004

Patterned Growth of Carbon Nanotubes or Nanofibers

A method and apparatus for the growth of carbon nanotubes or nanofibers in a desired pattern has been invented. The essence of the method is to grow the nanotubes or nanofibers by chemical vapor deposition (CVD) onto a patterned catalyst supported by a substrate. The figure schematically depicts salient aspects of the method and apparatus in a typical application. A substrate is placed in a chamber that contains both ion-beam sputtering and CVD equipment. The substrate can be made of any of a variety of materials that include several forms of silicon or carbon, and selected polymers, metals, ceramics, and even some natural minerals and similar materials. Optionally, the substrate is first coated with a noncatalytic metal layer (which could be a single layer or could comprise multiple different sublayers) by ion-beam sputtering. The choice of metal(s) and thickness(es) of the first layer (if any) and its sublayers (if any) depends on the chemical and electrical properties required for subsequent deposition of the catalyst and the subsequent CVD of the carbon nanotubes. A typical first-sublayer metal is Pt, Pd, Cr, Mo, Ti, W, or an alloy of two or more of these elements. A typical metal for the second sublayer or for an undivided first layer is Al at a thickness .1 nm or Ir at a thickness .5 nm. Proper choice of the metal for a second sublayer of a first layer makes it possible to use a catalyst that is chemically incompatible with the substrate. In the next step, a mask having holes in the desired pattern is placed over the coated substrate. The catalyst is then deposited on the coated substrate by ion-beam sputtering through the mask. Optionally, the catalyst could be deposited by a technique other than sputtering and/or patterned by use of photolithography, electron- beam lithography, or another suitable technique. The catalytic metal can be Fe, Co, Ni, or an alloy of two or more of these elements, deposited to a typical thickness in the range from 0.1 to 20 nm.

Delzeit, Lance D.↗

NASA NTRS2012

Effects of an ICME on the Lunar Exosphere

The lunar exosphere is produced in part by the sputtering of atoms off of the Moon's surface by solar wind ions. We present simulations of He, Na, K, Mg, and Ca in the lunar exosphere under nominal conditions. Next, we examine the resulting exospheric enhancement that occurs during the passage of an Interplanetary Coronal Mass Ejection (ICME). Enhanced sputtering under ICME conditions can increase the mass of the lunar exosphere 10-50 times the nominal value. The increase occurs rapidly within the onset of the ICME. Similarly, after the storm passes the Moon, the return to nominal exospheric density is also rapid. Because sputtered particles are energetic, many escape the Moon. Thus ICMEs induce a mass loss from the Moon. However, the implantation of solar wind into the lunar regolith is also enhanced during an ICME, resulting in mass addition to the Moon. This partially mitigates the mass loss caused by ICME sputtering. We present model estimates of the net lunar mass loss induced by ICMEs

Hurley, Dana M.↗

NASA NTRS2012

Electric Propulsion Induced Secondary Mass Spectroscopy

A document highlights a means to complement remote spectroscopy while also providing in situ surface samples without a landed system. Historically, most compositional analysis of small body surfaces has been done remotely by analyzing reflection or nuclear spectra. However, neither provides direct measurement that can unambiguously constrain the global surface composition and most importantly, the nature of trace composition and second-phase impurities. Recently, missions such as Deep Space 1 and Dawn have utilized electric propulsion (EP) accelerated, high-energy collimated beam of Xe+ ions to propel deep space missions to their target bodies. The energies of the Xe+ are sufficient to cause sputtering interactions, which eject material from the top microns of a targeted surface. Using a mass spectrometer, the sputtered material can be determined. The sputtering properties of EP exhaust can be used to determine detailed surface composition of atmosphereless bodies by electric propulsion induced secondary mass spectroscopy (EPI-SMS). EPI-SMS operation has three high-level requirements: EP system, mass spectrometer, and altitude of about 10 km. Approximately 1 keV Xe+ has been studied and proven to generate high sputtering yields in metallic substrates. Using these yields, first-order calculations predict that EPI-SMS will yield high signal-to-noise at altitudes greater than 10 km with both electrostatic and Hall thrusters.

Amini, Rashied↗

DOE OSTI2024

Exploring the relationship between deposition method, microstructure, and performance of Nb/Si-based superconducting coplanar waveguide resonators

Superconducting quantum circuits (SQC) are one of the most promising hardware platforms for quantum computing, yet their performance is currently limited by the presence of various structural defects inside the circuit's structure. Despite impressive progress in the past decade, a precise understanding of the origin of these defects from various fabrication processes and their impact on coherence is still lacking. Here, in this study, we performed a comprehensive investigation on the microstructure, superconductivity, and resonator quality factor of Nb films deposited by high-power impulse magnetron sputtering (HiPIMS) and direct current (DC) magnetron sputtering. A suite of characterization techniques, including electron microscopy with spectroscopy, secondary ion mass spectrometry, magneto-optical microscopy, and pump-probe reflectivity spectroscopy is used. We reveal that niobium (Nb) resonators fabricated using HiPIMS exhibit a smaller average grain size, thicker surface oxide with larger thickness variations (rougher surface), and a thicker amorphous Nb/Si interface layer compared to samples deposited by DC sputtering. We identified that the amorphous Nb oxides (mainly located at the Nb surface and along the grain boundaries) and Nb-Si amorphous layers (at the Nb/Si interface) are major and potential sources of two-level system (TLS), while off-stochiometric oxides and suboxides of Nb close to the surface, crystalline defects (i.e., dislocations at grain boundary, point defects introduced during deposition) are main contributors of non-TLS sources. Our findings clarify the relationship between different defects and coherence loss mechanisms, highlighting the importance of material microstructure control on performance optimization in SQC.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Fabrication of porous transport electrodes: Development of quantitative approach for quality control

This work focuses on porous transport electrodes (PTEs), which integrate the anodic catalyst with the adjacent Ti porous transport layer (PTL). Challenges in catalyst deposition on PTLs, particularly at low loadings, motivated this study to evaluate various fabrication methods and characterization approaches. This work investigated Pt-treated PTLs coated with Ir-based catalysts using several common methods, including airbrush coating, rod coating, ultrasonic spray coating, electrodeposition, and sputter deposition, with catalyst loadings ranging from 2.9 to 0.1 mg/cm 2 , providing the opportunity for comparisons across a large set of samples produced by different methods. Two widely accessible characterization techniques: X-ray computed tomography (XCT) and scanning electron microscopy energy dispersive X-ray spectroscopy (SEM-EDS) were explored. Initial evaluation of selected samples with XCT provided qualitative insights into catalyst distribution, however comprehensive quantitative analysis was limited. SEM-EDS enabled detailed information on the catalyst distribution both qualitatively and quantitatively using two metrics. Atomic and surface area % ratios of Pt:Ir and Ti:Ir revealed trends in catalyst loading and losses into the PTL pores, as well as evaluating the homogeneity of catalyst coatings. The analysis demonstrated that ultrasonic spray coating, electrodeposition, and sputter coating produced the most homogeneous coatings, with minimal catalyst losses observed for electrodeposition and sputter coating. By adapting common techniques with novel, standardized methodologies, this work establishes a universally applicable framework for cross-study comparison of PTEs. The SEM-EDS approach provides a practical, accessible tool for PTE characterization and contributes a reference dataset supporting both research development and rapid quality control.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Liquid lithium divertor analysis using coupled plasma material interaction model

A liquid lithium divertor can improve performance of future fusion devices by creating efficient power exhaust and improving the energy confinement via pumping of the hydrogen isotopes. In addition, significantly higher heat fluxes can be handled if controlled vapor shielding is used to redistribute the divertor heat flux over a wider area. Design and optimization of such a system calls for an analysis model which includes a strong two-way coupling between the plasma and divertor material. The incoming plasma heat and particle flux will affect the divertor surface temperature, which is a defining factor of the lithium evaporative and sputtered flux going into the plasma. Results of the coupled model based on the plasma edge code SOLPS-ITER and the computational fluid dynamics (CFD) code ANSYS-CFX will be presented for different configurations. An analytical slab flow model is used as a heat transfer boundary condition for SOLPS, defining particle flux from the wall via calculation of the surface temperature. At the final step, results of the SOLPS analysis are verified using a 3D CFD magnetohydrodynamics (MHD) analysis which uses heat and particle flux from SOLPS as a boundary condition. In addition to plasma heat flux, both analytical and CFD temperature models include several plasma material interaction effects, such as lithium evaporation, condensation and sputtering based on deuterium target flux. New adatom sputtering model based on the available experimental data is presented. Analytical model is expanded to include free surface axisymmetric configurations. Results of parametric studies of the divertor configurations with different lithium inlet temperature and velocity will be presented leading to the optimal design resulting in the lowest possible lithium contamination in the core.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Interaction of Molecular Hydrogen on α-Pu at 300 K: Nucleation of Hydrides and Pu-Catalyzed Carbides

An α-Pu sample was studied in its “as-received” and “sputtered” state by both X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectroscopy (ToF-SIMS). Analysis of the “as-received” surface indicated significant carbon and oxygen, with oxygen signal pertaining to plutonium dioxide (PuO 2 ) and sesquioxide (Pu 2 O 3 ). The “sputtered” clean metal surface was then dosed with hydrogen (H 2 ) gas at 300 K and found to nucleate hydride species (PuH x ). Interestingly, H 2 was observed to be critical for nucleation of carbides (Pu x C y ) by acting as a catalyst for Pu’s reaction with background gases. Because Pu metal has a high affinity for oxygen, reoxidation occurred under UHV, forming Pu x O y and disrupting both PuH x and Pu x C y growth. Observations from the experiments were modeled for the α-Pu(020) surface, illustrating the ability of H 2 to readily dissociate onto sputtered and speciated surfaces at 300 K. The projected density of states from these calculations were compared to experiments, showing good agreement between the Pu 5f, 6d, and 7s states and the H 1s, O 2p, and C 2p valence states. Overall, the above results indicated that the formed hydride layer is unstable at 300 K in UHV conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Nitrogen p-type doping in polycrystalline zinc selenide telluride films

Nitrogen-doped zinc selenide telluride (N:ZnSe x Te 1−x ) is of interest because it is one of the widest-gap II–VI semiconductors that can still be doped p-type with reasonably high hole concentrations. We sputter deposit N:ZnSe x Te 1−x films, varying Se/(Se + Te), or x, from 0 to 0.7, N 2 flow rate from 0.25 to 0.75 sccm, and substrate temperature from 250 to 370 °C. Increasing x from 0 to 0.39 at the optimal temperature of 370 °C and N 2 flow rate of 0.5 sccm leads to 1.3 atomic % nitrogen incorporation and wurtzite phase stabilization. Such doping and alloying increases hole concentration from 3 × 10 18 cm −3 to 3 × 10 19 cm −3 , although mobility drops from 0.4 to 0.02 cm 2 V −1 s −1 . Our sputtered N:ZnSe 0.38 Te 0.62 has an absorption onset 0.1 eV greater than the ZnTe value of 1.87 eV. Increasing x from 0 to 0.51 enhances transmittance by moving absorption onset from 1.87 to 2.11 eV with diminished band gap bowing likely due to disorder, and increases the work function from 5.12 to 5.42 eV. This combination of tunable properties makes sputtered N:ZnSe x Te 1−x desirable for transparent p-type contacts in polycrystalline Cd(Se,Te) optoelectronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Radiofrequency sheath rectification on WEST: application of the sheath-equivalent dielectric layer technique in tokamak geometry *

Radiofrequency sheath rectification is a phenomenon relevant to the operation of Ion Cyclotron Range of Frequencies (ICRFs) actuators in tokamaks. Techniques to model the sheath rectification on 3D ICRF antenna geometries have only recently become available (Shiraiw et al 2023 Nucl. Fusion 63 026024; Beers et al 2021 Phys. Plasmas 28 093503). In this work, we apply the 'sheath-equivalent dielectric layer' technique, used previously only on linear devices (Beers et al 2021 Phys. Plasmas 28 103508), in tokamak geometry, computing rectified sheath potentials on the WEST ICRF antenna. Advancing the state of the art in sheath rectification modeling, we compute the sheath potentials not just on the limiters, but also on the Faraday Screen bars. The calculations show a peak rectified DC potential of 300 V on the limiters and 500 V on the Faraday screen. Assuming a typical sputtering yield curve, the RF sheath rectification increases the sputtering yield from the limiters by a factor of 2.6 w.r.t. the sputtering due to the non-rectified thermal sheath.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Integrated modeling of RF-induced tungsten erosion at ICRH antenna structures in the WEST tokamak *

This paper introduces STRIPE (Simulated Transport of RF Impurity Production and Emission), an advanced modeling framework developed to analyze material erosion and the global transport of eroded impurities originating from radio-frequency (RF) antenna structures in magnetic confinement fusion devices. STRIPE integrates multiple physics modules: SolEdge3x for scrape-off-layer plasma profiles, COMSOL for 3D RF rectified sheath potentials, RustBCA for erosion yields and surface interactions, and global impurity transport for 3D ion energy-angle distributions and impurity transport. The framework is applied to an ion cyclotron RF-heated L-mode discharge (#57877) in the WEST tokamak, where it predicts a thirty-fold increase in gross tungsten erosion at antenna limiters during the transition from ohmic to ICRH operation. Additionally, under ICRH conditions, a tenfold enhancement in erosion is observed when comparing RF sheath effects to purely thermal sheath conditions. High-charge-state oxygen ions ($\mathrm{O}$ 6+ and above) are identified as the dominant contributors to tungsten sputtering. To validate the model, a synthetic diagnostic tool based on inverse photon efficiency (S/XB coefficients) from the ColRadPy collisional-radiative model enables direct comparison with spectroscopic measurements. Model predictions using a plasma composition of 1% oxygen and 99% deuterium show good agreement with observed W − I (400.9 nm) emission for discharge #57877, supporting the accuracy of the STRIPE framework. This study focuses specifically on gross erosion calculations to demonstrate STRIPE’s capabilities. Future extensions of this work will incorporate net erosion, re-deposition, self-sputtering effects, and whole-device modeling of sputtered tungsten impurity transport. STRIPE is also being applied to other RF-heated linear and toroidal devices, offering valuable insights for antenna design, impurity control, and performance optimization in next-generation fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗