Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aerodynamic Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Single-stage earth-orbital reusable vehicle space shuttle feasibility study. Volume 2: Aerodynamic model testing

This volume is one of a 6-volume final report of the Study of a Single-stage Earth-orbital Reusable Vehicle (SERV). The study was conducted by the Chrysler Corporation Space Division (CCSD) for the National Aeronautics and Space Administration, George C. Marshall Space Flight Center under Contract NAS8-26341. The purpose of the study was to evaluate the potential of SERV as the boost element of a candidate space transportation system. To establish the SERV potential, five key technical areas affecting concept feasibility were identified for examination: engine performance, aerodynamic characteristics, thermal protection, subsystem weights, and the landing method. The results of analyses are published in a final reporting consisting of the following six volumes: Volume 1 Summary Volume 2 Aerodynamic Model Testing Volume 3 Concept Evaluation Volume 4 Vehicle Definition Volume 5 Operations Definition Volume 6 Resources

C. E. Tharratt↗
NASA NTRS1987

Wind tunnel evaluation of a truncated NACA 64-621 airfoil for wind turbine applications

An experimental program to measure the aerodynamic performance of a NACA 64-621 airfoil with a truncated trailing edge for wind turbine applications has been conducted in the Ohio State University Aeronautical and Astronautical Research Laboratory 6 in. by 21 in. pressurized wind tunnel. The blunted or trailing edge truncated (TET) airfoil has an advantage over similar trailing edge airfoils because it is able to streamline a larger spar structure, while also providing aerodynamic properties that are quite good. Surface pressures were measured and integrated to determine the lift, pressure drag, and moment coefficients over angles of attack ranging from -14 to +90 deg at Mach 0.2 and Reynolds numbers of 1,000,000 and 600,000. Results are compared to the NACA 0025, 0030, and 0035 thick airfoils with sharp trailing edges. Comparison shows that the 30 percent thick NACA 64-621-TET airfoil has higher maximum lift, higher lift curve slope, lower drag at higher lift coefficients, and higher chordwise force coefficient than similar thick airfoils with sharp trailing edges.

Law, S. P.↗
NASA NTRS1989

Transonic airfoil design for helicopter rotor applications

Despite the fact that the flow over a rotor blade is strongly influenced by locally three-dimensional and unsteady effects, practical experience has always demonstrated that substantial improvements in the aerodynamic performance can be gained by improving the steady two-dimensional charateristics of the airfoil(s) employed. The two phenomena known to have great impact on the overall rotor performance are: (1) retreating blade stall with the associated large pressure drag, and (2) compressibility effects on the advancing blade leading to shock formation and the associated wave drag and boundary-layer separation losses. It was concluded that: optimization routines are a powerful tool for finding solutions to multiple design point problems; the optimization process must be guided by the judicious choice of geometric and aerodynamic constraints; optimization routines should be appropriately coupled to viscous, not inviscid, transonic flow solvers; hybrid design procedures in conjunction with optimization routines represent the most efficient approach for rotor airfroil design; unsteady effects resulting in the delay of lift and moment stall should be modeled using simple empirical relations; and inflight optimization of aerodynamic loads (e.g., use of variable rate blowing, flaps, etc.) can satisfy any number of requirements at design and off-design conditions.

Hassan, Ahmed A.↗
NASA NTRS2009

Proceedings of the Airframe Icing Workshop

The NASA Glenn Research Center (GRC) has a long history of working with its partners towards the understanding of ice accretion formation and its associated degradation of aerodynamic performance. The June 9, 2009, Airframe Icing Workshop held at GRC provided an opportunity to examine the current NASA airframe icing research program and to dialogue on remaining and emerging airframe icing issues and research with the external community. Some of the airframe icing gaps identified included, but are not limited to, ice accretion simulation enhancements, three-dimensional benchmark icing database development, three-dimensional iced aerodynamics modeling, and technology development for a smart icing system.

Colantonio, Ron O.↗
NASA NTRSDate not supplied

CFD Simulations of Landing and Takeoff CRM High-Lift Configurations

Numerical simulations have been performed for a conventional high-lift version of the Common Research Model (CRM) model corresponding to landing and take- off configurations. Computed values of lift and drag for the landing configuration are compared with the experimental data acquired in the 14- by 22-Foot Subsonic Tunnel (14×22) at the NASA Langley Research Center (LaRC). Simulations replicated the experimentally observed improvements in the lift characteristics in the presence of a nacelle chine. Flow visualization images indicate that vortices generated by the nacelle chine reduce flow separation regions on the upper surface of the wing at higher angles of attack. Based on such observations, the take-off configuration considered is also equipped with a nacelle chine, and testing of this configuration is planned in the 14×22 tunnel in near future. Preliminary solutions are also presented to explore the feasibility of using a localized flap gap blowing (LFGB) active flow control concept for improving the aerodynamic performance at take-off conditions.

aerodynamics↗
NASA NTRSDate not supplied

CFD Simulations of Landing and Takeoff CRM High-Lift Configurations

Numerical simulations have been performed for a conventional high-lift version of the Common Research Model (CRM) model corresponding to landing and take- off configurations. Computed values of lift and drag for the landing configuration are compared with the experimental data acquired in the 14- by 22-Foot Subsonic Tunnel (14×22) at the NASA Langley Research Center (LaRC). Simulations replicated the experimentally observed improvements in the lift characteristics in the presence of a nacelle chine. Flow visualization images indicate that vortices generated by the nacelle chine reduce flow separation regions on the upper surface of the wing at higher angles of attack. Based on such observations, the take-off configuration considered is also equipped with a nacelle chine, and testing of this configuration is planned in the 14×22 tunnel in near future. Preliminary solutions are also presented to explore the feasibility of using a localized flap gap blowing (LFGB) active flow control concept for improving the aerodynamic performance at take-off conditions.

aerodynamics↗
NASA NTRS2013

The Mars Science Laboratory (MSL) Entry, Descent And Landing Instrumentation (MEDLI): Hardware Performance and Data Reconstruction

The Mars Science Laboratory (MSL) Entry, Descent and Landing Instrumentation (MEDLI) hardware was a first-of-its-kind sensor system that gathered temperature and pressure readings on the MSL heatshield during Mars entry on August 6, 2012. MEDLI began as challenging instrumentation problem, and has been a model of collaboration across multiple NASA organizations. After the culmination of almost 6 years of effort, the sensors performed extremely well, collecting data from before atmospheric interface through parachute deploy. This paper will summarize the history of the MEDLI project and hardware development, including key lessons learned that can apply to future instrumentation efforts. MEDLI returned an unprecedented amount of high-quality engineering data from a Mars entry vehicle. We will present the performance of the 3 sensor types: pressure, temperature, and isotherm tracking, as well as the performance of the custom-built sensor support electronics. A key component throughout the MEDLI project has been the ground testing and analysis effort required to understand the returned flight data. Although data analysis is ongoing through 2013, this paper will reveal some of the early findings on the aerothermodynamic environment that MSL encountered at Mars, the response of the heatshield material to that heating environment, and the aerodynamic performance of the entry vehicle. The MEDLI data results promise to challenge our engineering assumptions and revolutionize the way we account for margins in entry vehicle design.

Little, Alan↗
NASA NTRS2016

Passive Rocket Diffuser Testing: Reacting Flow Performance of Four Second-Throat Geometries

Second-throat diffusers serve to isolate rocket engines from the effects of ambient back pressure. As one of the nation's largest rocket testing facilities, the performance and design limitations of diffusers are of great interest to NASA's Stennis Space Center. This paper describes a series of tests conducted on four diffuser configurations to better understand the effects of inlet geometry and throat area on starting behavior and boundary layer separation. The diffusers were tested for a duration of five seconds with a 1455-pound thrust, LO2/GH2 thruster to ensure they each reached aerodynamic steady state. The effects of a water spray ring at the diffuser exits and a water-cooled deflector plate were also evaluated. Static pressure and temperature measurements were taken at multiple axial locations along the diffusers, and Computational Fluid Dynamics (CFD) simulations were used as a tool to aid in the interpretation of data. The hot combustion products were confirmed to enable the diffuser start condition with tighter second throats than predicted by historical cold-flow data or the theoretical normal shock method. Both aerodynamic performance and heat transfer were found to increase with smaller diffuser throats. Spray ring and deflector cooling water had negligible impacts on diffuser boundary layer separation. CFD was found to accurately capture diffuser shock structures and full-flowing diffuser wall pressures, and the qualitative behavior of heat transfer. However, the ability to predict boundary layer separated flows was not consistent.

Jones, Daniel R.↗
NASA NTRS2015

CFD Simulations of the Space Launch System Ascent Aerodynamics and Booster Separation

This paper presents details of Computational Fluid Dynamic modeling of the Space Launch System during ascent. The primary focus of the paper is the flow simulation of the vehicle during ascent using the Overflow Navier-Stokes code. Computations of 739 first-stage flight conditions covering a range of Mach numbers, angles of attack, and roll angles were computed. The overset grid system contained 375 million grid points, and over 28 mil- lion CPU hours were used in the simulations. The simulations were run on the Pleiades supercomputer at the NASA Advanced Supercomputer Center at Ames Research Center. The data products from this work include integrated line-loads, surface pressure coefficients, venting pressures, and protuberance air-loads. Detailed comparisons were made of the aerodynamic performance predicted by Overflow and the wind-tunnel derived aero- dynamic database. A small number of the cases were run with two different turbulence models and with two differencing schemes. These results were used to quantify the sensitivity to the choice of the turbulence model and to the differencing scheme. The paper also introduces an effort to use the inviscid, unstructured Cartesian solver Cart3D to compute the aerodynamics during booster separation. Adaptive mesh refinement is being used to enable accurate simulations of sixteen booster-separation-motor plumes. The use of this tool is explored in preparation for building a booster-separation aerodynamic database.

Ascent Aerodynamics↗
NASA NTRS1979

Quiet Clean Short-haul Experimental Engine (QCSEE); acoustic performance of a 50.8-cm (20 inch) diameter variable pitch fan and inlet, test results and analysis, volume 1

Tests were run both in forward and in reverse thrust modes with a bellmouth inlet, five accelerating inlets (one hard wall and four treated) with a design throat Mach number of 0.79 at the takeoff condition, and four low Mach inlets (one hard wall and three treated) with a design throat Mach number of 0.6 at the takeoff condition. Unsuppressed and suppressed inlet radiated noise levels were measured at conditions representative of QCSEE takeoff, approach, and reverse thrust operations. Measured aerodynamic performance of the accelerating inlet is also included. The test objectives, facility, configurations, are described as well as the data analysis, results, and comparisons.

Bilwakesh, K. R.↗
NASA NTRS1992

In-flight Evaluation of Aerodynamic Predictions of an Air-launched Space Booster

Several analytical aerodynamic design tools that were applied to the Pegasus (registered trademark) air-launched space booster were evaluated using flight measurements. The study was limited to existing codes and was conducted with limited computational resources. The flight instrumentation was constrained to have minimal impact on the primary Pegasus missions. Where appropriate, the flight measurements were compared with computational data. Aerodynamic performance and trim data from the first two flights were correlated with predictions. Local measurements in the wing and wing-body interference region were correlated with analytical data. This complex flow region includes the effect of aerothermal heating magnification caused by the presence of a corner vortex and interaction of the wing leading edge shock and fuselage boundary layer. The operation of the first two missions indicates that the aerodynamic design approach for Pegasus was adequate, and data show that acceptable margins were available. Additionally, the correlations provide insight into the capabilities of these analytical tools for more complex vehicles in which the design margins may be more stringent.

Curry, Robert E.↗
NASA NTRS1993

In-flight evaluation of aerodynamic predictions of an air-launched space booster

Several analytical aerodynamic design tools that were applied to the Pegasus air-launched space booster were evaluated using flight measurements. The study was limited to existing codes and was conducted with limited computational resources. The flight instrumentation was constrained to have minimal impact on the primary Pegasus missions. Where appropriate, the flight measurements were compared with computational data. Aerodynamic performance and trim data from the first two flights were correlated with predictions. Local measurements in the wing and wing-body interference region were correlated with analytical data. This complex flow region includes the effect of aerothermal heating magnification caused by the presence of a corner vortex and interaction of the wing leading edge shock and fuselage boundary layer. The operation of the first two missions indicates that the aerodynamic design approach for Pegasus was adequate, and data show that acceptable margins were available. Additionally, the correlations provide insight into the capabilities of these analytical tools for more complex vehicles in which design margins may be more stringent.

Curry, Robert E.↗
NASA NTRS2015

Progress in Open Rotor Research: A U.S. Perspective

In response to the 1970s oil crisis, NASA created the Advanced Turboprop Project (ATP) to mature technologies for high-speed propellers to enable large reductions in fuel burn relative to turbofan engines of that era. Both single rotation and contra-rotation concepts were designed and tested in ground based facilities as well as flight. Some novel concepts configurations that were not well publicized at the time, were proposed as part of the effort. The high-speed propeller concepts did provide fuel burn savings, albeit with some acoustics and structural challenges to overcome. When fuel prices fell, the business case for radical new engine configurations collapsed and the research emphasis returned to high bypass ducted configurations. With rising oil prices and increased environmental concerns there is renewed interest in high-speed propeller based engine architectures. Contemporary analysis tools for aerodynamics and aeroacoustics have enabled a new era of blade designs that have both high efficiency and acceptable noise characteristics. A recent series of tests in the U.S. have characterized the aerodynamic performance and noise from these modern contra-rotating propeller designs. Additionally the installation and noise shielding aspects for conventional airframes and blended wing bodies have been studied. Historical estimates of propfan performance have relied on legacy propeller performance and acoustics data. Current system studies make use of the modern propeller data with higher fidelity installation effects data to estimate the performance of a contemporary aircraft system with favorable results. This paper presents the current state of high-speed propeller open rotor research within the U.S. from an overall viewpoint of the various efforts ongoing. The current projections for the technology are presented.

Aerodynamics↗
NASA NTRS1983

The aerodynamic design and performance of the General Electric/NASA EEE fan

The aerodynamic design and test results of the fan and quarter-stage component for the GE/NASA Energy Efficient Engine (EEE) are presented. The fan is a high bypass ratio, single-stage design having 32 part-span shrouded rotor blades, coupled with a unique quarter-stage arrangement that provides additional core-stream pressure ratio and particle separation. The fan produces a bypass pressure ratio of 1.65 at the exit of the low aspect ratio vane/frame and a core-stream pressure ratio of 1.67 at the entrance to the core frame struts. The full-scale fan vehicle was instrumented, assembled and tested as a component in November 1981. Performance mapping was conducted over a range of speeds and bypass ratios using individually-controlled bypass and core-stream discharge valves. The fan bypass and core-stream test data showed excellent results, with the fan exceeding all performance goals at the important engine operating conditions.

Sullivan, T. J.↗
NASA NTRS2018

Project Link!: Dynamics and Control of In-Flight Wing Tip Docking

Project Link! is a NASA-led effort to study the feasibility of multi-aircraft aerial docking systems. In these systems, a group of vehicles physically link to each other during flight to form a larger ensemble vehicle with increased aerodynamic performance and mission utility. This paper presents a dynamic model and control architecture for a system of fixed-wing vehicles with this capability. The dynamic model consists of the 6 degree-of-freedom fixed-wing aircraft equations of motion, a spring-damper-magnet system to represent the linkage force between constituent vehicles, and the NASA-Burnham-Hallock wingtip vortex model to represent the close-proximity aerodynamic interactions between constituents before the linking occurs. The control architecture consists of a guidance algorithm to autonomously drive the constituents towards their linking partners and an inner-loop angular rate controller. A simulation was constructed from the model, and the flight dynamic modes of the linked system were compared to the individual vehicles. Simulation results for both before and after linking are presented.

Cooper, John R.↗
NASA NTRSDate not supplied

The Effect of Boundary Layer Character on Stochastic Rotor Blade Vortex Shedding Noise

This work illustrates the effect of a rotor blade’s boundary layer on the broadband LBL-VS self-noise emitted from an optimum hovering rotor through experimental and multi-fidelity computational studies. Blade surface roughness effects associated with different manufacturing techniques and the effect of adding a boundary layer trip were shown to decrease LBL-VS noise by upwards of 30 dB at the frequency of maximum emission with a slight penalty in aerodynamic performance when compared with smooth rotor blades. Low-fidelity 2-D viscous flow analysis verified the presence of laminar separation bubbles on the rotor blades which are responsible for LBL-VS noise. Three high-fidelity lattice-Boltzmann simulations were conducted with different wall-functions to predict the boundary layer character correspondent to their experimental counterpart and the resultant presence or absence of LBL-VS noise. Excellent aerodynamic and aeroacoustic agreement was seen between the lattice-Boltzmann simulations and the experimental data for the cases with surface roughness and the boundary layer trip, with the broadband noise results from the simulation with fully turbulent wall-functions diverging from the experimental results above 5 kHz. The transitional wall-function simulation which emulated the smooth experimental blades underpredicted thrust by 14% and broadband noise by a minimum of 10 dB with an accurately predicted broadband noise trend.

Christopher S Thurman↗
NASA NTRS1981

Performance and loads data from a wind tunnel test of a full-scale, coaxial, hingeless rotor helicopter

A full-scale XH-59A advancing blade concept helicopter was tested in Ames Research Center's 40 by 80 foot wind tunnel. The helicopter was tested with the rotor on and off, rotor hub fairings on and off, interrotor shaft fairing on and off, rotor instrumentation module on and off, and auxiliary propulsion thrust on and off. An advance ratio range of 0.25 and 0.45 with the rotor on and from 60 to 180 knots with the rotor off was investigated. Data on aerodynamic forces and moments, rotor loads, rotor control positions and vibration for the XH-59A as well as the aerodynamic performance of the isolated rotor are presented.

Felker, F. F., III↗