SEARCH · Search NASA

Results for “Defect modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Computational Investigation of Oxidative Etch Pitting in FiberForm and Its Impact on Material Properties

Oxidation-driven carbon erosion does not occur uniformly but rather through the development of localized etch pits at active surface sites. These active sites form due to atomic defects on the carbon surface, making them significantly more reactive than the surrounding, non-defective areas. As a result, these sites are the first to react during ablation, leading to their removal. This process creates new defects in neighboring atoms, increasing their reactivity and causing localized carbon removal around these active sites. In this way, the highly reactive defective areas serve as nucleation points for the formation and growth of etch pits, which can have adverse effects on structural integrity of FiberForm. To better understand how these etch pits impact the material properties of carbon fiber microstructures, we have developed a new capability within the direct simulation Monte Carlo (DSMC) framework to capture the etch pit formation process. This capability, integrated into the DSMC code SPARTA (Stochastic Parallel Rarefied-gas Time-accurate Analyzer), models material removal in the presence of active sites, leading to the formation of etch pits. The current work focuses on studying the effects of these etch pits on the material properties of FiberForm, a widely used base material in thermal protection systems (TPS). The microstructure of virgin FiberForm, obtained via X-ray microtomography, is imported into SPARTA to generate the ablated geometries with etch pits. These modified microstructures are then analyzed using the Porous Microstructure Analysis (PuMA) software to compute various material properties, including elasticity, thermal conductivity, and permeability. We investigate the variation of these properties due to the complex surface topology changes caused by etch pit formation. Additionally, we compare the effects of pitting with the conventional model of shrinking fibers, traditionally used to simulate the ablation of carbon structures. Significant differences emerge between the two approaches. Consequently, this physically realistic model of material removal through etch pit formation offers improved accuracy in predicting the degradation of carbon-based TPS during oxidation. It also provides insights into other mechanisms, such as spallation, where chunks of material are removed into the flow due to etch pit growth. Ultimately, this model enhances our understanding of failure modes in these materials during ablation.

PuMA↗

NASA NTRS1982

General contamination criteria for optical surfaces

Physical models are developed for establishing criteria to decide on the acceptable contamination level of optical devices in space-borne conditions. Optical systems can be degraded in terms of decreased throughput, i.e., transmissivity or reflectivity, or increases in the total integrated scatter (TIS). Performance losses can be caused by particulate accretion, molecular film accretion, and impact cratering. A quantitative relationship is defined for film thickness and loss of throughput. Formulas are also developed for cases where induced surface defects are larger than the desired viewing wavelengths, or smaller or of the same order of the observed wavelengths. The techniques are used to quantify the degradation of a VUV solar coronagraph, a VUV stellar telescope, and a solar cell due to TIS. Applications are projected for estimating the contamination sensitivity of specific instruments, assessing the contamination hazard from known particulates, or to define clean room standards.

Bremer, J. C.↗

NASA NTRS1984

Influence of soft inclusions on the strength of wrought materials

The three dimensional soft particles (such as sulfides, silicates and voids) present in most materials are modelled by circular voids in sheet metal. Relationships are sought between the shape and orientation of a hole after rolling and testing in tension. Then, the effect of hole shape and size on mechanical properties is considered experimentally. The presence of voids has a negligible influence on the ultimate tensile stress of ductile materials based on the unperforated area because plastic flow neutralizes the stress intensification present in the elastic region. However, the shape and orientation of the defects are found to play an important role relative to strain at fracture. In certain engineering applications the strain at fracture is more important than the stress at fracture and in this sense the presence of voids are considered to influence the strength of a ductile material.

Pai, D. M.↗

NASA NTRS1991

The formation and evolution of domain walls

Domain walls are sheet-like defects produced when the low energy vacuum has isolated degenerate minima. The researchers' computer code follows the evolution of a scalar field, whose dynamics are determined by its Lagrangian density. The topology of the scalar field determines the evolution of the domain walls. This approach treats both wall dynamics and reconnection. The researchers investigated not only potentials that produce single domain walls, but also potentials that produce a network of walls and strings. These networks arise in axion models where the U(1) Peccei-Quinn symmetry is broken into Z sub N discrete symmetries. If N equals 1, the walls are bounded by strings and the network quickly disappears. For N greater than 1, the network of walls and strings behaved qualitatively just as the wall network shown in the figures given here. This both confirms the researchers' pessimistic view that domain walls cannot play an important role in the formation of large scale structure and implies that axion models with multiple minimum can be cosmologically disastrous.

Press, William H.↗

NASA NTRS1991

Late-time cosmological phase transitions

It is shown that the potential galaxy formation and large scale structure problems of objects existing at high redshifts (Z approx. greater than 5), structures existing on scales of 100 M pc as well as velocity flows on such scales, and minimal microwave anisotropies ((Delta)T/T) (approx. less than 10(exp -5)) can be solved if the seeds needed to generate structure form in a vacuum phase transition after decoupling. It is argued that the basic physics of such a phase transition is no more exotic than that utilized in the more traditional GUT scale phase transitions, and that, just as in the GUT case, significant random Gaussian fluctuations and/or topological defects can form. Scale lengths of approx. 100 M pc for large scale structure as well as approx. 1 M pc for galaxy formation occur naturally. Possible support for new physics that might be associated with such a late-time transition comes from the preliminary results of the SAGE solar neutrino experiment, implying neutrino flavor mixing with values similar to those required for a late-time transition. It is also noted that a see-saw model for the neutrino masses might also imply a tau neutrino mass that is an ideal hot dark matter candidate. However, in general either hot or cold dark matter can be consistent with a late-time transition.

Schramm, David N.↗

NASA NTRS2010

NASA Tech Briefs, November 2010

Topics covered include: Portable Handheld Optical Window Inspection Device; Salience Assignment for Multiple-Instance Data and Its Application to Crop Yield Prediction; Speech Acquisition and Automatic Speech Recognition for Integrated Spacesuit Audio Systems ; Predicting Long-Range Traversability from Short-Range Stereo-Derived Geometry; Browser-Based Application for Telemetry Monitoring of Robotic Assets; Miniature Low-Noise G-Band I-Q Receiver; Methods of Using a Magnetic Field Response Sensor Within Closed, Electrically Conductive Containers; Differential Resonant Ring YIG Tuned Oscillator; Microfabricated Segmented-Involute-Foil Regenerator for Stirling Engines; Reducing Seal Adhesion in Low Impact Docking Systems; Optimal Flow Control Design; Corrosion-Resistant Container for Molten-Material Processing; Reusable Hot-Wire Cable Cutter; Deployment of a Curved Truss; High-Volume Airborne Fluids Handling Technologies to Fight Wildfires; Modeling of Alkane Oxidation Using Constituents and Species; Fabrication of Lanthanum Telluride 14-1-11 Zintl High-Temperature Thermoelectric Couple; A Computer Model for Analyzing Volatile Removal Assembly; Analysis of Nozzle Jet Plume Effects on Sonic Boom Signature; Optical Sidebands Multiplier; Single Spatial-Mode Room-Temperature-Operated 3.0 to 3.4 micrometer Diode Lasers; Self-Nulling Beam Combiner Using No External Phase Inverter; Portable Dew Point Mass Spectrometry System for Real-Time Gas and Moisture Analysis; Maximum Likelihood Time-of-Arrival Estimation of Optical Pulses via Photon-Counting Photodetectors; Handheld White Light Interferometer for Measuring Defect Depth in Windows; Decomposition Algorithm for Global Reachability on a Time-Varying Graph; Autonomous GN and C for Spacecraft Exploration of Comets and Asteroids; Efficient Web Services Policy Combination; Using CTX Image Features to Predict HiRISE-Equivalent Rock Density; Isolation of the Paenibacillus phoenicis, a Spore-Forming Bacterium; Monolithically Integrated, Mechanically Resilient Carbon-Based Probes for Scanning Probe Microscopy; Cell Radiation Experiment System; Process to Produce Iron Nanoparticle Lunar Dust Simulant Composite; Inversion Method for Early Detection of ARES-1 Case Breach Failure; Use of ILTV Control Laws for LaNCETS Flight Research;and Evaluating Descent and Ascent Trajectories Near Non-Spherical Bodies.

Source record↗

NASA NTRS2012

Rhombohedral cubic semiconductor materials on trigonal substrate with single crystal properties and devices based on such materials

Growth conditions are developed, based on a temperature-dependent alignment model, to enable formation of cubic group IV, group II-V and group II-VI crystals in the [111] orientation on the basal (0001) plane of trigonal crystal substrates, controlled such that the volume percentage of primary twin crystal is reduced from about 40% to about 0.3%, compared to the majority single crystal. The control of stacking faults in this and other embodiments can yield single crystalline semiconductors based on these materials that are substantially without defects, or improved thermoelectric materials with twinned crystals for phonon scattering while maintaining electrical integrity. These methods can selectively yield a cubic-on-trigonal epitaxial semiconductor material in which the cubic layer is substantially either directly aligned, or 60 degrees-rotated from, the underlying trigonal material.

Park, Yeonjoon↗

NASA NTRS1976

Model for thickness dependence of radiation charging in MOS structures

The model considers charge buildup in MOS structures due to hole trapping in the oxide and the creation of sheet charge at the silicon interface. The contribution of hole trapping causes the flatband voltage to increase with thickness in a manner in which square and cube dependences are limiting cases. Experimental measurements on samples covering a 200 - 1000 A range of oxide thickness are consistent with the model, using independently obtained values of hole-trapping parameters. An important finding of our experimental results is that a negative interface charge contribution due to surface states created during irradiation compensates most of the positive charge in the oxide at flatband. The tendency of the surface states to 'track' the positive charge buildup in the oxide, for all thicknesses, applies both in creation during irradiation and in annihilation during annealing. An explanation is proposed based on the common defect origin of hole traps and potential surface states.

Viswanathan, C. R.↗

NASA NTRS1984

Defects in High Speed Growth of EFG Silicon Ribbon

Silicon ribbons grown by the Edge-defined Film-fed Growth (EFG) technique exhibit a characteristic defect structure typified by twins, dislocations, grain boundaries and silicon carbide inclusions. As growth speed is increased from less than 2.5 cm per minute, the structural details change. The major difference between the ribbons grown at speeds below and above 2.5 cm per minute is in the generation of a cellular structure at the higher growth speeds, observable in the ribbon cross section. The presence of the cross sectional structure leads, in general, to a reduction in cell performance. Models to explain the formation of such a cross sectional structure are presented and discussed.

Rao, C. V. H. N.↗

NASA NTRS1984

An atomistic model of slip formation

The results of an atomistic model for the simulation of the early stages of crack initiation in a two-dimensional triangular lattice are presented. In the current model, each particle in the system is treated discretely and assumed to be interacting with the surrounding particles via Lennard-Jones potentials. A uniaxial load (in incremental elongations) is applied to the rectangular two-dimensional slab in either the x or the y direction. After each incremental elongation the system is equilibrated using a static method. Initially, elastic behavior in the x and y directions is observed. Continued elongation results in plastic deformation. In lattices with point defects, the defects first move to the surface, creating vacancies which trigger plastic deformation.

Halicioglu, T.↗

NASA NTRS1993

Prediction of nonlinear optical properties of organic materials. General theoretical considerations

The prediction of nonlinear optical properties of organic materials is geared to assist materials scientists in the selection of good candidate molecules. A brief summary of the quantum mechanical methods used for estimating hyperpolarizabilities will be presented. The advantages and limitations of each technique will be discussed. Particular attention will be given to the finite-field method for calculating first and second order hyperpolarizabilities, since this method is better suited for large molecules. Corrections for dynamic fields and bulk effects will be discussed in detail, focusing on solvent effects, conformational isomerization, core effects, dispersion, and hydrogen bonding. Several results will be compared with data obtained from third-harmonic-generation (THG) and dc-induced second harmonic generation (EFISH) measurements. These comparisons will demonstrate the qualitative ability of the method to predict the relative strengths of hyperpolarizabilities of a class of compounds. The future application of molecular mechanics, as well as other techniques, in the study of bulk properties and solid state defects will be addressed. The relationship between large values for nonlinear optical properties and large conjugation lengths is well known, and is particularly important for third-order processes. For this reason, the materials with the largest observed nonresonant third-order properties are conjugated polymers. An example of this type of polymer is polydiacetylene. One of the problems in dealing with polydiacetylene is that substituents which may enhance its nonlinear properties may ultimately prevent it from polymerizing. A model which attempts to predict the likelihood of solid-state polymerization is considered, along with the implications of the assumptions that are used. Calculations of the third-order optical properties and their relationship to first-order properties and energy gaps will be discussed. The relationship between monomeric and polymeric third-order optical properties will also be considered.

Cardelino, B.↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Carbon Ablators↗

NASA NTRS2015

Real Time Fatigue Damage Growth Assessment of a Composite Three-Stringer Panel Using Passive Thermography

Fatigue testing of advanced composite structures is critical to validate both structural designs and damage prediction models. In-situ inspection methods are necessary to track damage onset and growth as a function of load cycles. Passive thermography is a large area, noncontact inspection technique that is used to detect composite damage onset and growth in real time as a function of fatigue cycles. The thermal images are acquired in synchronicity to the applied compressive load using a dual infrared camera acquisition system for full (front and back) coverage. Image processing algorithms are investigated to increase defect contrast areas. The thermal results are compared to non-immersion ultrasound inspections and acoustic emission data.

Zalameda, Joseph N.↗

NASA NTRS1984

Tensile Fracture of Ductile Materials

For brittle materials, circular voids play an important role relative to fracture, intensifing both tensile and compressive stresses. A maximum intensified tensile stress failure criterion applies quite well to brittle materials. An attempt was made to explore the possibility of extending the approach to the tensile fracture of ductile materials. The three dimensional voids that exist in reality are modelled by circular holes in sheet metal. Mathematical relationships are sought between the shape and size of the hole, after the material is plastically deformed, and the amount of deformation induced. Then, the effect of hole shape, size and orientation on the mechanical properties is considered experimentally. The presence of the voids does not affect the ultimate tensile strength of the ductile materials because plastic flow wipes out the stress intensification caused by them. However, the shape and orientation of the defect is found to play an important role in affecting the strain at fracture.

Pai, D. M.↗

NASA NTRS1988

Cosmic strings

Cosmic strings are linear topological defects which are predicted by some grand unified theories to form during a spontaneous symmetry breaking phase transition in the early universe. They are the basis for the only theories of galaxy formation aside from quantum fluctuations from inflation based on fundamental physics. In contrast to inflation, they can also be observed directly through gravitational lensing and their characterisitc microwave background anisotropy. It was recently discovered that details of cosmic string evolution are very differnt from the so-called standard model that was assumed in most of the string-induced galaxy formation calculations. Therefore, the details of galaxy formation in the cosmic string models are currently very uncertain.

Bennett, David P.↗

NASA NTRS1991

Probability of brittle failure

A methodology was developed for collecting statistically representative data for crack initiation and arrest from small number of test specimens. An epoxy (based on bisphenol A diglycidyl ether and polyglycol extended diglycyl ether and cured with diethylene triamine) is selected as a model material. A compact tension specimen with displacement controlled loading is used to observe multiple crack initiation and arrests. The energy release rate at crack initiation is significantly higher than that at a crack arrest, as has been observed elsewhere. The difference between these energy release rates is found to depend on specimen size (scale effect), and is quantitatively related to the fracture surface morphology. The scale effect, similar to that in statistical strength theory, is usually attributed to the statistics of defects which control the fracture process. Triangular shaped ripples (deltoids) are formed on the fracture surface during the slow subcritical crack growth, prior to the smooth mirror-like surface characteristic of fast cracks. The deltoids are complementary on the two crack faces which excludes any inelastic deformation from consideration. Presence of defects is also suggested by the observed scale effect. However, there are no defects at the deltoid apexes detectable down to the 0.1 micron level.

Kim, A.↗