SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A turbulence generating grid was designed and installed in the turbine inlet which produced the target nominal value of 10 percent free stream turbulence. Aerodynamic documentation of the rotor and stator midspan surface pressure distributions were obtained. Midspan heat transfer data were obtained on the rotor and stator for variations in inlet turbulence, rotor-stator axial spacing, and rotor incidence.
NASA is currently investigating the readiness of Advanced Sensors and Instrumentation to meet the requirements of new initiatives in space. The following technical objectives and technologies are briefly discussed: smart and nonintrusive sensors; onboard signal and data processing; high capacity and rate adaptive data acquisition systems; onboard computing; high capacity and rate onboard storage; efficient onboard data distribution; high capacity telemetry; ground and flight test support instrumentation; power distribution; and workstations, video/lighting. The requirements for high fidelity data (accuracy, frequency, quantity, spatial resolution) in hostile environments will continue to push the technology developers and users to extend the performance of their products and to develop new generations.
The integrated number-peak-flux relation measured by the Burst and Transient Source Experiment (BATSE) on board the Compton Gamma Ray Observatory is compared with several standard cosmological distributions for gamma-ray bursts (GRBs). Friedmann-Robertson-Walker models were used along with the assumption that the bursts are standard candles and have no number or luminosity evolution. For a given Omega spectral shape, we used a free parameter, essentially the comoving number density of bursts, to generate a best fit between the cosmology and the measured relation. Our results are shown for a subsample of the first 260 GRBs recorded by BATSE. We find acceptable fits between simple cosmological models and the brightness distribution data, as determined by the Kolmogorov-Smirnov one-distribution statistical test. One cannot distinguish a single best cosmological model from the goodness of the fits. The best fit implies that BATSE GRBs are complete out to a redshift of about unity. However, significantly higher and lower redshifts, by as much as a factor of 2, are possible for other marginally acceptable fits.
Organizations in Europe, Australia, and the United States have recently broadened constituent assimilation activities beyond that water vapor, which has been assimilated for years in the numerical weather prediction community. Many of these activities have focused on ozone, with some efforts focused on the entire suite of reactive constituents that control the ozone distribution. This talk will draw from results from the near real-time ozone data assimilation system being run by NASA's Data Assimilation Office. This system utilizes ozone observations from both the TOMS and the SBUV instrument to generate global synoptic maps of ozone. The initial application of this product is to provide ozone fields to assist in the atmospheric corrections' that are necessary for the retrieval of information from other NASA instruments. The validation of the ozone assimilation system shows that the assimilated product agrees well with independent HALOE and ozonesonde observations. This suggests that the product is of sufficient quality to be extended to other applications. This talk will enumerate these other applications and present initial results from exploratory research. The applications being considered include estimates of tropospheric ozone, provision of ozone fields for interactive retrievals, use of analysis increments from the assimilation to evaluate model performance, and development of long-term consistent three-dimensional global ozone fields. The results from the exploratory studies are promising, and help demonstrate how assumptions made in the p development of the ozone assimilation impact the other applications. For instance, RMS errors in the current product are large near the tropopause, which is sensitive to the specification of vertical correlation functions, which in turns impacts the amount of ozone analyzed to be in the troposphere. How these sensitivities impact the different applications will also be discussed.
Organizations in Europe, Australia, and the United States have recently broadened constituent assimilation activities beyond water vapor, which has been assimilated for years in the numerical weather prediction applications. Many of these activities have focused on ozone, with some efforts focused on the entire suite of reactive constituents that control the ozone distribution. This talk will draw from results from the near real-time ozone data assimilation system being run by NASA's Data Assimilation Office. This system utilizes ozone observations from both the TOMS and the SBUV instrument to generate global synoptic maps of ozone. The initial application of this product is to provide ozone fields to assist in the atmospheric corrections' that are necessary for the retrieval of information from other NASA instruments. The validation of the ozone assimilation system shows that the assimilated product agrees well with independent HALOE and ozonesonde observations. Aside from providing a global synoptic map, there is verifiable geophysical information at higher vertical resolution than either of the date types input into the system. This talk will establish the validation results and enumerate applications of the ozone data assimilation system. Results from exploratory research will be presented. The applications being considered include estimates of tropospheric ozone, provision of ozone fields for interactive retrievals, use of analysis increments from the assimilation to evaluate model performance, and development of long-term consistent three-dimensional global ozone fields. The results from the exploratory studies are promising, and help demonstrate how assumptions made in the development of the ozone assimilation impact the other applications. For instance, RMS errors in the current product are large near the tropopause, which is sensitive to the specification of vertical correlation functions, which in turns impacts the amount of ozone analyzed to be in the troposphere. How these sensitivities impact the different applications will also be discussed.
Stars like our sun (initial masses between 0.8 to 8 solar masses) end their lives as swollen red giants surrounded by cool extended atmospheres. The nuclear reactions in their cores create carbon, nitrogen and oxygen, which are transported by convection to the outer envelope of the stellar atmosphere. As the star finally collapses to become a white dwarf, this envelope is expelled from the star to form a planetary nebula (PN) rich in organic molecules. The physics, dynamics, and chemistry of these nebulae are poorly understood and have implications not only for our understanding of the stellar life cycle but also for organic astrochemistry and the creation of prebiotic molecules in interstellar space. We are working toward generating three-dimensional models of planetary nebulae (PNe), which include the size, orientation, shape, expansion rate and mass distribution of the nebula. Such a reconstruction of a PN is a challenging problem for several reasons. First, the data consist of images obtained over time from the Hubble Space Telescope (HST) and spectra obtained from Kitt Peak National Observatory (KPNO) and Cerro Tololo Inter-American Observatory (CTIO). These images are of course taken from a single viewpoint in space, which amounts to a very challenging tomographic reconstruction. Second, the fact that we have two disparate and orthogonal data types requires that we utilize a method that allows these data to be used together to obtain a solution. To address these first two challenges we employ Bayesian model estimation using a parameterized physical model that incorporates much prior information about the known physics of the PN. In our previous works we have found that the forward problem of the comprehensive model is extremely time consuming. To address this challenge, we explore the use of a set of hierarchical models, which allow us to estimate increasingly more detailed sets of model parameters. These hierarchical models of increasing complexity are akin to scientific theories of increasing sophistication, with each new model/theory being a refinement of a previous one by either incorporating additional prior information or by introducing a new set of parameters to model an entirely new phenomenon. We apply these models to both a simulated and a real ellipsoidal PN to initially estimate the position, angular size, and orientation of the nebula as a two-dimensional object and use these estimates to later examine its three-dimensional properties. The efficiency/accuracy tradeoffs of the techniques are studied to determine the advantages and disadvantages of employing a set of hierarchical models over a single comprehensive model.
Stars like our sun (initial masses between 0.8 to 8 solar masses) end their lives as swollen red giants surrounded by cool extended atmospheres. The nuclear reactions in their cores create carbon, nitrogen and oxygen, which are transported by convection to the outer envelope of the stellar atmosphere. As the star finally collapses to become a white dwarf, this envelope is expelled from the star to form a planetary nebula (PN) rich in organic molecules. The physics, dynamics, and chemistry of these nebulae are poorly understood and have implications not only for our understanding of the stellar life cycle but also for organic astrochemistry and the creation of prebiotic molecules in interstellar space. We are working toward generating three-dimensional models of planetary nebulae (PNe), which include the size, orientation, shape, expansion rate and mass distribution of the nebula. Such a reconstruction of a PN is a challenging problem for several reasons. First, the data consist of images obtained over time from the Hubble Space Telescope (HST) and spectra obtained from Kitt Peak National Observatory (KPNO) and Cerro Tololo Inter-American Observatory (CTIO). These images are of course taken from a single viewpoint in space, which amounts to a very challenging tomographic reconstruction. Second, the fact that we have two disparate and orthogonal data types requires that we utilize a method that allows these data to be used together to obtain a solution. To address these first two challenges we employ Bayesian model estimation using a parameterized physical model that incorporates much prior information about the known physics of the PN. In our previous works we have found that the forward problem of the comprehensive model is extremely time consuming. To address this challenge, we explore the use of a set of hierarchical models, which allow us to estimate increasingly more detailed sets of model parameters. These hierarchical models of increasing complexity are akin to scientific theories of increasing sophistication, with each new model/theory being a refinement of a previous one by either incorporating additional prior information or by introducing a new set of parameters to model an entirely new phenomenon. We apply these models to both a simulated and a real ellipsoidal PN to initially estimate the position, angular size, and orientation of the nebula as a two-dimensional object and use these estimates to later examine its three-dimensional properties. The efficiency/accuracy tradeoffs of the techniques are studied to determine the advantages and disadvantages of employing a set of hierarchical models over a single comprehensive model.
Because of the extreme variability of rain rate in space and time and the difficulties with remote sensing methods of measuring rain rates, accurate determination of rainfall over large areas and time periods has long been a problem for hydrologists, meteorogists, and climatologists. A number of statistical models of rain have been developed in order to investigate the impact of rain variability on satellite remote sensing methods, validation of satellite rain products, and generation of rain maps with accompanying error estimates. These models may be useful in examining 'sub-grid scale' issues in representing precipitation in numerical mdoels. A stochastic model will first be described which can generate time-dependent high-resolution spatial rain fields with space and time correlations similar to those seen in rain data, as well as representing the presence of areas with zero rain rate and log-normally distributed rain rates where there is rain. A simpler model derived from this, formulated in the spectral domain, seems to imply fractal-like rain statistics at small scales when fit to rain data.
This paper describes a flexible agent-based ecological forecasting system that combines multiple distributed data sources and models to provide near-real-time answers to questions about the state of the Earth system We build on novel techniques in automated constraint-based planning and natural language interfaces to automatically generate data products based on descriptions of the desired data products.
The initiative to explore space and extend a human presence across our solar system to revisit the moon and Mars post enormous technological challenges to the nation's space agency and aerospace industry. Key areas of technology development needs to enable the endeavor include advanced materials, structures and mechanisms; micro/nano sensors and detectors; power generation, storage and management; advanced thermal and cryogenic control; guidance, navigation and control; command and data handling; advanced propulsion; advanced communication; on-board processing; advanced information technology systems; modular and reconfigurable systems; precision formation flying; solar sails; distributed observing systems; space robotics; and etc. Quality assurance concerns such as functional performance, structural integrity, radiation tolerance, health monitoring, diagnosis, maintenance, calibration, and initialization can affect the performance of systems and subsystems. It is thus imperative to employ innovative nondestructive evaluation methodologies to ensure quality and integrity of advanced space systems. Advancements in integrated multi-functional sensor systems, autonomous inspection approaches, distributed embedded sensors, roaming inspectors, and shape adaptive sensors are sought. Concepts in computational models for signal processing and data interpretation to establish quantitative characterization and event determination are also of interest. Prospective evaluation technologies include ultrasonics, laser ultrasonics, optics and fiber optics, shearography, video optics and metrology, thermography, electromagnetics, acoustic emission, x-ray, data management, biomimetics, and nano-scale sensing approaches for structural health monitoring.
The NASA Soil Moisture Active Passive (SMAP) mission generates, among other data sets, the Level 4 Soil Moisture (L4 SM) product. The L4 SM algorithm is based on the assimilation of SMAP radiometer brightness temperature observations into the NASA Catchment land surface model using a spatially distributed ensemble Kalman filter. The L4 SM data are published with a mean latency of approx. 2.5 days from the time of observation and provide global, three-hourly, 9 km resolution estimates of surface and root-zone soil moisture and related land surface states and fluxes. In 2018, the product was upgraded from Version 3 to Version 4. Underlying the new version is a revised modeling system that includes improved input parameter datasets for land cover, topography, and vegetation height that are based on recent, high quality space-borne remote sensing observations. Land cover inputs were updated to the GlobCover2009 product, which is based on satellite observations from the Medium Resolution Imaging Spectrometer. Topographic statistics now rely on observations from the Shuttle Radar Topography Mission. Finally, vegetation height inputs are derived from space-borne Lidar measurements. Additionally, SMAP Level-2 soil moisture retrievals and in situ soil moisture measurements were used to calibrate a particular Catchment model parameter that governs the recharge of soil moisture from the models root-zone excess reservoir into the surface excess reservoir. Specifically, the replenishment of soil moisture near the surface from below under non-equilibrium conditions was substantially reduced, which brings the models surface soil moisture more in line with the SMAP Level 2 and in situ soil moisture. Finally, the calibration of the assimilated SMAP brightness temperatures changed substantially from Version 3 to Version 4. Considerable effort went into the version upgrade, creating an expectation that the new version is improved over the old version. Indeed, some aspects of the new version are clearly better. However, other aspects are not, and on balance, the overall improvement is modest at best. In this presentation we summarize the skill of the new and old versions vs. independent in situ measurements and in terms of data assimilation diagnostics, including, for example, the statistics of the (soil moisture) analysis increments and the observation minus forecast (brightness temperatures) residuals. We share our experience with trying to improve to the L4 SM product and the lessons learned from the effort.
The goal of the NASA Global Land Data Assimilation System (GLDAS, https://ldas.gsfc.nasa.gov/gldas(https://ldas.gsfc.nasa.gov/gldas)) is to generate optimal fields of land surface states and fluxes by ingesting satellite- and ground-based observational data products, using advanced land surface modeling and data assimilation techniques (Rodell et al., 2004).The GLDAS dataset currently archived at and distributed by the NASA Goddard Earth Sciences Data and Information Services Center (GES DISC, https://disc.gsfc.nasa.gov/ (https://disc.gsfc.nasa.gov/)) is GLDAS Version 2 (GLDAS-2). It contains a series of output fields from the upgraded Noah-3.6, Catchment-F2.5, and VIC-4.1.2 Land Surface Models (LSMs) in the Land Information System (LIS-V7, https://lis.gsfc.nasa.gov/ (https://lis.gsfc.nasa.gov/)). GLDAS-2 has three components:GLDAS-2.0, GLDAS-2.1, and GLDAS-2.2. GLDAS-2.0 is forced entirely with the upgraded Princeton Meteorological ForcingV2.2 Dataset and provides a temporally consistent series from 1948 through 2014. GLDAS-2.1 is forced with a combination of model and observation data, with data spanning from 2000 to the present. The GLDAS-2.2 product suite uses data assimilation(DA), whereas the GLDAS-2.0 and GLDAS-2.1 products are "open-loop" (i.e., no data assimilation). The choice of forcing data, as well as DA observation source, variable, and scheme, varies for different GLDAS-2.2 products. The currently availableGLDAS-2.2 data contain a daily 0.25-degree output from the Catchment-F2.5 LSM in LIS-V7. The data are forced with the meteorological analysis fields from the operational European Centre for Medium-Range Weather Forecasts Integrated Forecasting System (ECMWF-IFS) and assimilated with GRACE and GRACE-FO data, ranging from February 1, 2003 to the present. The current GLDAS-2.0 and 2.1 Noah LSM data were reprocessed in November 2019 and January 2020 respectively and their data from Catchment and VIC LSMs are new to the GLDAS-2 collection. This presentation provides a summary of theGLDAS-2 data products, their land surface fields, and their related data services at the GES DISC; and a description of the majorGLDAS-2 climatological characteristics as well as the intercomparison with the data of the previous version.
Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.
Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.
Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.
The NASA LeRC in Cleveland, Ohio has completed the development and integration of a Power Management and Distribution (PMAD) DC Testbed. This testbed is a reduced scale representation of the end to end, sources to loads, Space Station Freedom Electrical Power System (SSF EPS). This unique facility is being used to demonstrate DC power generation and distribution, power management and control, and system operation techniques considered to be prime candidates for the Space Station Freedom. A key capability of the testbed is its ability to be configured to address system level issues in support of critical SSF program design milestones. Electrical power system control and operation issues like source control, source regulation, system fault protection, end-to-end system stability, health monitoring, resource allocation, and resource management are being evaluated in the testbed. The SSF EPS control functional allocation between on-board computers and ground based systems is evolving. Initially, ground based systems will perform the bulk of power system control and operation. The EPS control system is required to continuously monitor and determine the current state of the power system. The DC Testbed Control System consists of standard controllers arranged in a hierarchical and distributed architecture. These controllers provide all the monitoring and control functions for the DC Testbed Electrical Power System. Higher level controllers include the Power Management Controller, Load Management Controller, Operator Interface System, and a network of computer systems that perform some of the SSF Ground based Control Center Operation. The lower level controllers include Main Bus Switch Controllers and Photovoltaic Controllers. Power system status information is periodically provided to the higher level controllers to perform system control and operation. The data acquisition function of the control system is distributed among the various levels of the hierarchy. Data requirements are dictated by the control system algorithms being implemented at each level. A functional description of the various levels of the testbed control system architecture, the data acquisition function, and the status of its implementationis presented.
As expert systems become more widely used, their access to large amounts of external information becomes increasingly important. This information exists in several forms such as statistical, tabular data, knowledge gained by experts and large databases of information maintained by companies. Because many expert systems, including CLIPS, do not provide access to this external information, much of the usefulness of expert systems is left untapped. The scope of this paper is to describe a database extension for the CLIPS expert system shell. The current industry standard database language is SQL. Due to SQL standardization, large amounts of information stored on various computers, potentially at different locations, will be more easily accessible. Expert systems should be able to directly access these existing databases rather than requiring information to be re-entered into the expert system environment. The ORACLE relational database management system (RDBMS) was used to provide a database connection within the CLIPS environment. To facilitate relational database access a query generation system was developed as a CLIPS user function. The queries are entered in a CLlPS-like syntax and are passed to the query generator, which constructs and submits for execution, an SQL query to the ORACLE RDBMS. The query results are asserted as CLIPS facts. The query generator was developed primarily for use within the ICADS project (Intelligent Computer Aided Design System) currently being developed by the CAD Research Unit in the California Polytechnic State University (Cal Poly). In ICADS, there are several parallel or distributed expert systems accessing a common knowledge base of facts. Expert system has a narrow domain of interest and therefore needs only certain portions of the information. The query generator provides a common method of accessing this information and allows the expert system to specify what data is needed without specifying how to retrieve it.
This document discusses the nature of light (including classical light and photons), encryption, quantum key distribution (QKD), light polarization and beamsplitters and their application to information communication. A quantum of light represents the smallest possible subdivision of radiant energy (light) and is called a photon. The QKD key generation sequence is outlined including the receiver broadcasting the initial signal indicating reception availability, timing pulses from the sender to provide reference for gated detection of photons, the sender generating photons through random polarization while the receiver detects photons with random polarization and communicating via data link to mutually establish random keys. The QKD network vision includes inter-SATCOM, point-to-point Gnd Fiber and SATCOM-fiber nodes. QKD offers an unconditionally secure method of exchanging encryption keys. Ongoing research will focus on how to increase the key generation rate.