Search NASA⌕ Search

SEARCH · Search NASA

Results for “ELASTIC PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Laminate behavior for SiC fiber-reinforced reaction-bonded silicon nitride matrix composites

The room temperature mechanical properties of SiC fiber reinforced reaction-bonded silicon nitride matrix composite laminates (SiC/RBSN) have been measured. The laminates contained approx 30 volume fraction of aligned 142-micron diameter SiC fiber in a porous RBSN matrix. Three types of laminate studied were unidirectional: (1) (0) sub 8, (2) (10) sub 8, and (3) (45) sub 8, and (90) sub 8; cross plied laminates (0 sub 2/90 sub 2); and angle plied laminates: (+45 sub 2/-45 sub 2). Each laminate contained eight fiber plies. Results of the unidirectionally reinforced composites tested at various angles to the reinforcement direction indicate large anisotropy in in-plane properties. In addition, strength properties of these composites along the fiber direction were independent of specimen gage length and were unaffected by notches normal to the fiber direction. Splitting parallel to the fiber at the notch tip appears to be the dominant crack blunting mechanism responsible for notch insensitive behavior of these composites. In-plane properties of the composites can be improved by 2-D laminate construction. Mechanical property results for (0 sub 2/90 sub 2) sub s and (+45/-45 sub 2) sub s laminates showed that their matrix failure strains were similar to that for (0) sub 8 laminates, but their primary elastic moduli, matrix cracking strengths, and ultimate composite strengths were lower. The elastic properties of unidirectional, cross-ply, and angle-ply composites can be predicted from modified constitutive equations and laminate theory. Further improvements in laminate properties may be achieved by reducing the matrix porosity and by optimizing the bond strength between the SiC fiber and RBSN matrix.

Bhatt, Ramakrishna T.↗

Compressibility and hardness of Co-based bulk metallic glass: A combined experimental and density functional theory study

An incompressible Co{sub 54}Ta{sub 11}B{sub 35} bulk metallic glass (BMG) was investigated using in situ high-pressure synchrotron diffraction and nanoindendation. The elastic constants were deduced from the experiments based on the isotropic model. The Vickers hardness was measured to be 17.1 GPa. The elastic moduli and hardness are the highest values known in BMGs. The theoretically calculated elastic properties by density-functional study were well consistent with experimental measurements. The analysis of charge density and bonding character indicates the covalent character of Co-B and B-B bonds, underlying the unusually high elastic modulus and hardness in this material.

36 MATERIALS SCIENCE↗

Mechanical Response of Thermoelectric Materials

A sufficient mechanical response of thermoelectric materials (TEMats) to structural loadings is a prerequisite to the exploitation of any candidate TEMat's thermoelectric efficiency. If a TEMat is mechanically damaged or cracks from service-induced stresses, then its thermal and electrical functions can be compromised or even cease. Semiconductor TEMats tend to be quite brittle and have a high coefficient of thermal expansion; therefore, they can be quite susceptible to mechanical failure when subjected to operational thermal gradients. Because of this, sufficient mechanical response (vis-a-vis, mechanical properties) of any candidate TEMat must be achieved and sustained in the context of the service-induced stress state to which it is subjected. This report provides an overview of the mechanical responses of state-of-the-art TEMats; discusses the relevant properties that are associated with those responses and their measurement; and describes important, nonequilibrium phenomena that further complicate their use in thermoelectric devices. For reference purposes, the report also includes several appendixes that list published data on elastic properties and strengths of a variety of TEMats.

36 MATERIALS SCIENCE↗

Deformational models of rifting and folding on Venus

Features of presumed tectonic origin on Venus are reviewed, and lithospheric strength envelopes are derived based on laboratory measurements of the deformational properties of crustal and subcrustal rocks, extrapolated to conditions appropriate to Venus. Models for rifting and folding are developed that use this lithospheric structure and take into account both brittle and ductile yielding as well as finite elastic strength. For both rifting and folding, structures with characteristic widths and spacings are predicted whose size depends on the thickness of the lithosphere, density contrast, and elastic properties of the layer. Finally, the model predictions are compared with the widths and spacings of observed tectonic features, and it is concluded that they are consistent with a relatively strong mantle layer separated from a thin brittle surface layer by a ductile lower crust. These results allow constraints to be placed on the crustal thickness and thermal gradient on Venus.

Banerdt, W. Bruce↗

Elastic, mechanical, and thermodynamic properties of Bi-Sb binaries: Effect of spin-orbit coupling

Using first-principles calculations, we systematically study the elastic stiffness constants, mechanical properties, elastic wave velocities, Debye temperature, melting temperature, and specific heat of several thermodynamically stable crystal structures of BixSb 1-x (0 < x < 1) binaries, which are of great interest due to their numerous inherent rich properties, such as thermoelectricity, thermomagnetic cooling, strong spin-orbit coupling (SOC) effects, and topological features in the electronic band structure. We analyze the bulk modulus (B), Young's modulus (E), shear modulus (G), B/G ratio, and Poisson's ratio ($\nu$) as a function of the Bi concentration in BixSb 1-x . The effect of SOC on the above-mentioned properties is further investigated. In general, we observe that the SOC effects cause elastic softening in most of the studied structures. Three monoclinic structures of Bi-Sb binaries are found to exhibit significantly large auxetic behavior due to the hingelike geometric structure of bonds. The Debye temperature and the magnitude of the elastic wave velocities monotonically increase with increasing Sb concentration. However, anomalies were observed at very low Sb concentration. We also discuss the specific-heat capacity versus temperature data for all studied binaries. Our theoretical results are in excellent agreement with the existing experimental and theoretical data. The comprehensive understanding of the material properties such as hardness, mechanical strength, melting temperature, propagation of the elastic waves, auxeticity, and heat capacity is vital for practical applications of the studied binaries.

36 MATERIALS SCIENCE↗

Nanomechanical and topographical imaging of living cells by atomic force microscopy with colloidal probes

Atomic Force Microscopy (AFM) has a great potential as a tool to characterize mechanical and morphological properties of living cells; these properties have been shown to correlate with cells’ fate and patho-physiological state in view of the development of novel early-diagnostic strategies. Although several reports have described experimental and technical approaches for the characterization of cellular elasticity by means of AFM, a robust and commonly accepted methodology is still lacking. Here, we show that micrometric spherical probes (also known as colloidal probes) are well suited for performing a combined topographic and mechanical analysis of living cells, with spatial resolution suitable for a complete and accurate mapping of cell morphological and elastic properties, and superior reliability and accuracy in the mechanical measurements with respect to conventional and widely used sharp AFM tips. We address a number of issues concerning the nanomechanical analysis, including the applicability of contact mechanical models and the impact of a constrained contact geometry on the measured Young’s modulus (the finite-thickness effect). We have tested our protocol by imaging living PC12 and MDA-MB-231 cells, in order to demonstrate the importance of the correction of the finite-thickness effect and the change in Young’s modulus induced by the action of a cytoskeleton-targeting drug.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Crack propagation driven by crystal growth

Crystals that grow in confinement may exert a force on their surroundings and thereby drive crack propagation in rocks and other materials. We describe a model of crystal growth in an idealized crack geometry in which the crystal growth and crack propagation are coupled through the stress in the surrounding bulk solid. Subcritical crack propagation takes place during a transient period, which may be very long, during which the crack velocity is limited by the kinetics of crack propagation. When the crack is sufficiently large, the crack velocity becomes limited by the kinetics of crystal growth. The duration of the subcritical regime is determined by two non-dimensional parameters, which relate the kinetics of crack propagation and crystal growth to the supersaturation of the fluid and the elastic properties of the surrounding material.

58 GEOSCIENCES↗

A coarsening method for linear peridynamics.

A method is obtained for deriving peridynamic material models for a sequence of increasingly coarsened descriptions of a body. The starting point is a known detailed, small scale linearized state-based description. Each successively coarsened model excludes some of the aterial present in the previous model, and the length scale increases accordingly. This excluded material, while not present explicitly in the coarsened model, is nevertheless taken into account implicitly through its effect on the forces in the coarsened material. Numerical examples emonstrate that the method accurately reproduces the effective elastic properties of a composite as well as the effect of a small defect in a homogeneous medium.

36 MATERIALS SCIENCE↗

Mechanical stiffening and thermal softening of rare earth chalcogenides

The pressure and temperature dependent elastic properties such as melting temperature nature in REX; (RE = La, Pr, Eu; X = O, S, Se, Te) chalcogenides is computed with emphasis on charge transfer interactions and covalent contribution in the effective interionic interaction potential. The pressure dependent elastic constants and melting temperature confirms that REX chalcogens lattice get stiffened as a consequence of bond compression and bond strengthening, however thermal softening arose due to bond expansion and bond weakening is evidenced from temperature dependence of melting temperature (T{sub M})

36 MATERIALS SCIENCE↗

Ionizing particle detection based on phononic crystals

Most conventional radiation detectors are based on electronic or photon collections. In this work, we introduce a new and novel type of ionizing particle detector based on phonon collection. Helium ion radiation treats tumors with better precision. There are nine known isotopes of helium, but only helium-3 and helium-4 are stable. Helium-4 is formed in fusion reactor technology and in enormous quantities during Big Bang nucleo-synthesis. In this study, we introduce a technique for helium-4 ion detection (sensing) based on the innovative properties of the new composite materials known as phononic crystals (PnCs). PnCs can provide an easy and cheap technique for ion detection compared with conventional methods. PnC structures commonly consist of a periodic array of two or more materials with different elastic properties. The two materials are polymethyl-methacrylate and polyethylene polymers. The calculations showed that the energies lost to target phonons are maximized at 1 keV helium-4 ion energy. There is a correlation between the total phonon energies and the transmittance of PnC structures. The maximum transmission for phonons due to the passage of helium-4 ions was found in the case of making polyethylene as a first layer in the PnC structure. Therefore, the concept of ion detection based on PnC structure is achievable.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Velocity Crossover Between Hydrous and Anhydrous Forsterite at High Pressures

The elastic properties of hydrous forsterite, Mg{sub 2-x}SiO{sub 4}H{sub 2x}, are relevant to interpreting seismic velocity anomalies in the Earth's mantle. In this study, we used Brillouin scattering to determine the single-crystal elasticity of forsterite with 0.9(1) wt.% H{sub 2}O (x = 0.14) to 14 GPa. Aggregate bulk and shear moduli of hydrous forsterite increase with pressure at a greater rate than those of the corresponding anhydrous phase. Compared with anhydrous forsterite, we observe a 7% increase in the pressure derivative of the bulk modulus (K{prime}{sub S0} = 4.50(5)), and a 25% increase in the pressure derivative of the shear modulus (G{prime}{sub 0} = 1.75(5)) for forsterite with near maximum possible water content. Using our results, we calculated the compressional, V{sub P}, and shear, V{sub S}, velocities of forsterite as a function of pressure at 300 K. Whereas V{sub P} and V{sub S} of hydrous forsterite are 0.6% and 0.4% slower than those of anhydrous forsterite at ambient pressure, velocity crossovers at {approx} 3-4 GPa result in higher hydrous forsterite velocities at pressures corresponding to depths below {approx} 120 km. At the pressure of the 410-km discontinuity, V{sub P} and V{sub S} of hydrous forsterite exceed those of anhydrous forsterite by 1.1(1)% and 1.9(1)%, respectively. This implies that incorporation of water could decrease the magnitude of the velocity contrast at 410-km depth between forsterite and wadsleyite. Although the effects of hydration on temperature derivatives of the elastic moduli of forsterite and wadsleyite are not yet known, from the current data we estimate that the presence of {approx} 0.4 wt.% H{sub 2}O in forsterite (at 60 mol%) could lower the P and S velocity contrast at 410-km depth to 3.8(4)% and 4.8(6)%, respectively. At high pressures, hydration also decreases the V{sub P}/V{sub S} ratio of forsterite, and lowers the maximum P wave azimuthal anisotropy and S wave splitting of forsterite.

79 ASTRONOMY AND ASTROPHYSICS↗

Photothermoelastic contrast in nanoscale infrared spectroscopy

The contrast formation mechanism in nanoscale Infrared (IR) Spectroscopy is analyzed. The temperature distribution and elastic displacement across the illuminated T-shape boundary between two materials with different IR-radiation absorption coefficients and thermo-physical and elastic properties located on a rigid substrate are calculated self-consistently for different frequencies f ~ (1 kHz–1 MHz) of IR-radiation modulation (fully coupled problem). Analytical expressions for the temperature and displacement profiles across the “thermo-elastic step” are derived in the decoupling approximation for f = 0 (“static limit”), and conditions for approximation validity at low frequencies of IR-modulation are established. The step height was found to be thickness-independent for thick layers and proportional to the square of the thickness for very thin films. The theoretical results will be of potential interest for applications in the scanning thermo-ionic and thermal infrared microscopies for relatively long sample thermalization times and possibly for photothermal induced resonance microscopy using optomechanical probes.

36 MATERIALS SCIENCE↗

Low Velocity Sphere Impact of a Soda Lime Silicate Glass

This report summarizes TARDEC-sponsored work at Oak Ridge National Laboratory (ORNL) during the FY11 involving low velocity (< 30 m/s or < 65 mph) ball impact testing of Starphire soda lime silicate glass. The intent was to better understand low velocity impact response in the Starphire for sphere densities that bracketed that of rock. Five sphere materials were used: borosilicate glass, soda-lime silicate glass, steel, silicon nitride, and alumina. A gas gun was fabricated to produce controlled velocity delivery of the spheres against Starphire tile targets. Minimum impact velocities to initiate fracture in the Starphire were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between the any of the five sphere-Starphire-target combinations. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Frictional effects contribute to fracture initiation. (2) Spheres with a lower elastic modulus require less force to initiate fracture in the Starphire than spheres with a higher elastic modulus. (3) Contact-induced fracture did not initiate in the Starphire SLS for impact kinetic energies < 150 mJ. Fracture sometimes initiated or kinetic energies between {approx} 150-1100 mJ; however, it tended to occur when lower elastic modulus spheres were impacting it. Contact-induced fracture would always occur for impact energies > 1100 mJ. (4) The force necessary to initiate contact-induced fracture is higher under dynamic or impact conditions than it is under quasi-static indentation conditions. (5) Among the five used sphere materials, silicon nitride was the closest match to 'rock' in terms of both density and (probably) elastic modulus.

36 MATERIALS SCIENCE↗

Density and Elasticity of Zr46Cu37.6Ag8.4Al8 Bulk Metallic Glass at High Pressure

Compressional and shear wave velocities of Zr{sub 46}Cu{sub 37.6}Ag{sub 8.4}Al{sub 8} bulk metallic glass (BMG) have been measured up to 6.3 GPa at room temperature using ultrasonic interferometry in conjunction with synchrotron X-radiography. The densities at high pressures are uniquely determined using the measured velocities. The experimental results for the elastic moduli of Zr{sub 46}Cu{sub 37.6}Ag{sub 8.4}Al{sub 8} show a reasonable agreement with the Voigt-Reuss-Hill approximation of the element metal phases, indicating that the elastic properties of the BMG have a close correlation with its constituent components.

36 MATERIALS SCIENCE↗

Femtosecond electron diffraction: Preparation and characterization of (110)-oriented bismuth films

Here, we present a new approach to synthesize (110)-oriented ultrathin membranes of bismuth (Bi). This rather exotic orientation was achieved by directing the growth through rationale control of lattice matching. Bi films were hetero-epitaxially grown on the (100)-surface of freshly cleaved potassium chloride crystals. The sample orientation was characterized by x-ray and electron diffraction. In addition, high quality free-standing films were obtained after dissolution of the substrate in water and controlled evaporation. Femtosecond electron diffraction (FED) was, therefore, used to monitor the coherent shear acoustic phonons in (110)-oriented free-standing Bi films produced by impulsive femtosecond optical excitation. The small de Broglie wavelength (flat Ewald sphere) of keV-electrons combined with an off-Bragg detection scheme provided a magnified view of shear atomic motions, i.e., lattice distortions in the transverse direction. All-optical pump-probe experiments are usually insensitive to shear displacements, a fact that makes FED a unique non-contact method to achieve the complete characterization of elastic properties of nanoscale materials.

36 MATERIALS SCIENCE↗

Computer modeling of the local structure, mixing properties, and stability of solid solutions of alkaline-earth metal oxides

A technique for the computer modeling of disordered binary oxide solid solutions MO-M'O in a wide composition range has been developed. The method of atomistic pair potentials was used for 4 x 4 x 4 supercells. The parameters of the potentials are optimized using the structural and elastic properties of pure components MgO, CaO, SrO, and BaO. The temperature dependences of the heat capacity and entropy are calculated for pure components. The excess mixing properties (enthalpy, volume, bulk modulus, vibrational entropy) are found for different compositions of Mg{sub x}Ca{sub (1-x)}O, Ca{sub x}Sr{sub (1-x)}O, and Sr{sub x}Ba{sub (1-x)}O solid solutions. Temperature and composition dependences of the excess Gibbs energy were constructed, which made it possible to approximately estimate the critical decomposition temperatures and limits of component miscibility. Statistical analysis of lattice distortions in the first and second coordination spheres reveals a detailed picture of the solid-solution local structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ab-initio study of B{sub 2}-type technetium AB (A=Tc, B=Nb and Ta) intermetallic compounds

The structural, electronic and elastic properties of AB type (A = Tc, B = Nb and Ta) technetium intermetallic compounds are studied using full potential linearized plane wave (FP-LAPW) method within generalized gradient approximation (GGA). The calculated lattice parameters agree well with the experimental results. The elastic constants obey the stability criteria for cubic system. Ductility for these compounds has been analyzed using the Pugh’s rule and Cauchy’s pressure and found that all the compounds are ductile in nature. Bonding nature is discussed in terms of Fermi surface and band structures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Integrated characterization of CO 2 storage reservoirs on the Rock Springs Uplift combining geomechanics, geochemistry, and flow modeling

This project improves understanding of the effects CO 2 injection and storage on geomechanical, petrophysical, and other properties on two potential reservoirs, the Madison Limestone and Weber Sandstone, at the Rock Springs Uplift, southwest Wyoming. Rock physics studies, laboratory experiments, and computer simulations were employed. Two groups of rock samples were prepared, one aged with formation brine and the second aged with CO 2 -saturated formation brine and subsequently used for geomechanical, geochemical, and petrophysical testing. Rock physics studies provided a facies classification to discriminate among different lithologies and to investigate the feasibility of predicting petrophysical properties using seismic inversion. By applying a zone-wise regression relation established in this facies analysis, a 3D reservoir model was developed. It was determined that time-lapse seismic data are not feasible for monitoring CO 2 displacement at the Rock Springs Uplift or to mitigate leakage-risks situations because pressure and fluid saturation have small effects on elastic velocities and synthetic seismograms. The small variations that do occur are due to the low porosity of the sandstone and the high stiffness of the dolomite. In the Madison Limestone, mineral dissolution due to reaction with CO 2 -saturated brine was observed in highly permeable pathways while mineral precipitation happened in intergranular or micropores. Changes in pore size were quantified via Time-Domain Nuclear Magnetic Resonance transverse relaxation time (T 2 ) and diffusion coefficient distributions. As opposed to continuous injection of CO 2 -saturated brine, a subtle increase in porosity after static ‘soaking’ with CO 2 -saturated brine increases permeability due to the heterogeneity of changes in pore and pore throat sizes. Porosity-permeability relationships are fitted using a power-law function that can be adopted to model time-evolved porosity and permeability in a transport-limited CO 2 injection process. The effect of CO 2 -saturated brine on the linear elastic properties of Weber Sandstone and Madison Limestone cannot be generally concluded. Considering horizontal and vertical orientations and different confining pressures, no consistent relationship between stress (or strain) data and reaction with CO 2 -saturated brine was observed in the nonlinear plastic and post-failure regime. The change of elastic constants due to reaction with CO 2 -saturated brine is more significant in Madison Limestone than in Weber Sandstone; however, no consistent trend was observed. Reservoir simulations suggest that injectivity for Weber Sandstone is adversely impacted by low permeability. Changes in confining pressure do not impact injection rate and can be ignored while the effect of changes to pore pressure cannot. The effect of confining pressure and pore pressure on the size of the CO 2 plume in the Madison Limestone is negligible because of higher permeability. Geomechanical and petrophysical properties induced by CO 2 -brine-rock reactions were time-dependent. Simulations considered these time-dependent properties and indicate that injectivity, porosity distribution, pressure distribution and CO 2 saturation were affected.

58 GEOSCIENCES↗