Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLAME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Buoyancy Effects on Concurrent Flame Spread Over Thick PMMA

The flammability of combustible materials in a spacecraft is important for fire safety applications because the conditions in spacecraft environments differ from those on earth. Experimental testing in space is difficult and expensive. However, reducing buoyancy by decreasing ambient pressure is a possible approach to simulate on-earth the burning behavior inside spacecraft environments. The objective of this work is to determine that possibility by studying the effect of pressure on concurrent flame spread, and by comparison with microgravity data, observe up to what point low-pressure can be used to replicate flame spread characteristics observed in microgravity. Specifically, this work studies the effect of pressure and microgravity on upward/concurrent flame spread over 10 mm thick polymethyl methacrylate (PMMA) slabs. Experiments in normal gravity were conducted over pressures ranging between 100 and 40 kPa and a forced flow velocity of 200 mm/s. Microgravity experiments were conducted during NASA’s Spacecraft Fire Experiment (Saffire II), on board the Cygnus spacecraft at 100 kPa with an air flow velocity of 200 mm/s. Results show that reductions of pressure slow down the flame spread over the PMMA surface approaching that in microgravity. The data is correlated in terms of a non-dimensional mixed convection analysis that describes the convective heat transferred from the flame to the solid, and the primary mechanism controlling the spread of the flame. The extrapolation of the correlation to low pressures predicts well the flame spread rate obtained in microgravity in the Saffire II experiments. Similar results were obtained by the authors with similar experiments with a thin composite cotton/fiberglass fabric (published elsewhere). Both results suggest that reduced pressure can be used to approximately replicate flame behavior of untested gravity conditions for the burning of thick and thin solids. This work could provide guidance for potential ground-based testing for fire safety design in spacecraft and space habitats.

Environmental conditions↗

Extinction of the Stagnation Point Diffusion Flame: Effect of Conductive Heat Loss into Solid Interior

The flammability boundary of a solid is U-shaped with the ordinate as ambient oxygen percentage (or total pressure) and the abscissa represents flow velocity, gravity level, stretch rate, etc. The left side of the flammability boundary is the quenching branch, and the right side is the blow-off branch. Quenching is due to a weak flame whose heat release from combustion cannot overcome the excessive heat losses from, for example, radiation. Blow-off is due to a short gas residence time that is smaller than the chemical reaction time (traditionally referred to as the small Damköhler number effect). For thick solids, the heat conduction into the solid interior has a long transient after ignition before the solid temperature reaches the steady state. During this slow transient, there is excessive (i.e. more than that at the steady state) gas phase heat conduction into the solid interior. From the viewpoint of the quasi-static gaseous flame, this is an additional heat loss that will affect the gas flame's flammability. In this work, a previously developed one-dimensional axisymmetric stagnation-point diffusion flame model is extended to account for the excessive heat loss into the solid beyond the steady burning state. A non-dimensional excessive conductive heat loss parameter Ψ is defined in the paper to account for the transient solid effect. For each Ψ, the gas phase is considered reaching a quasi-steady state. Extensive numerical computations have been performed to determine the extinction boundary and the characteristics of near-limit flames. The U-shaped flammability boundary is now a series of boundaries with Ψ as a parameter. Flame structures under the same environment condition but with different Ψ are compared. For a given oxygen ambient, the extinction boundary Ψ vs stretch rate is an inverted U-shape. The boundary consists of a blowoff branch and a radiative quenching branch. Extensive computed data including flame and pyrolysis temperatures, burning rate, flame standoff distance, species concentration, and reaction rate are presented along the extinction boundaries. Heat balance analysis is performed for both the gas phase and the gas-solid interface. Along the extinction boundary, the relative importance of conduction, convection, radiation, and chemical reaction are analyzed in detail.

Stagnation point diffusion flame↗

Flame Deflector Ablation Analysis based on Artemis 1 Launch Environment

This paper presents the updated ablative analysis methods used to determine Artemis 1 launch load environment on the flame deflector for the design based on Artemis I Assessments. The flame trench under Pad 39B at Kennedy Space Center contains a flame deflector to safely divert the exhaust plume from the SLS rocket during launch. During launch of Artemis I the refurbished flame trench and the new flame deflector experienced peak temperatures of over 2,000 degrees Fahrenheit (over 1,000 degrees Celsius) for several seconds. These extreme conditions caused ablation (material removal) from the steel plates. This paper contains flame deflector heat flux values for design based on Artemis I assessment. Post flight images of the flame deflector are shown along with “Pre vs Post” Flame Deflector scan image to measure the post flight deviations. Using COMSOL, a method to calculate a heat flux value due to measured deviations in the deflector plates caused by ablation is shown.

Artemis I↗

Analysis of ignition and stabilization modes in diesel spray flames using large eddy simulations and chemical explosive mode analysis

In this work, spray flames under diesel engine conditions are numerically investigated to understand the ignition and stabilization characteristics, based on state-of-the-art large eddy simulations (LES) and chemical explosive mode analysis (CEMA). In particular, CEMA is employed to identify such critical flame features as auto-ignition, premixed flame fronts, cool and strongly burning flames, and local extinction. In particular, a recently developed CEMA-based criterion for demarcating local combustion modes, that is, auto-ignition, diffusion-assisted ignition, and extinction, is applied to gain in-depth insights into the interactions of local chemical and transport processes. A series of one-dimensional non-premixed flamelets with varying air temperatures and scalar dissipation rates are first analyzed using CEMA with a focus on the role of each local mode in the transient ignition process. CEMA-based diagnostics are then applied to diesel spray flames at different ambient temperatures. The structure of local combustion modes is identified, while the contribution from each local mode to overall flame burning is quantified at different stages of the flame developing process. Effects of the ambient temperature on local combustion mode distribution, and subsequently on the ignition and stabilization mechanisms, are further examined. Results show that auto-ignition is the main mechanism for flame initiation and stabilization, while the role of diffusion is substantially enhanced as ambient temperature decreases.

assisted-ignition↗

Regime diagrams and characteristics of flame patterns in radial microchannels with temperature gradients

Comprehensive regime diagrams of flame pattern formation in radial microchannels with temperature gradients were drawn based on experimental findings. A premixed methane-air mixture was introduced at the center of microchannels formed by two parallel circular quartz plates that were heated with an external porous burner to create a positive temperature gradient condition in the direction of flow. Combustion behavior in those microchannels at channel widths of 0.5, 1.0, 1.5, 2.0, 2.5, and 3.0 mm were experimentally investigated. Regime diagrams of various stable and unstable flame patterns were obtained, confirming that the flame pattern is a strong function of mixture equivalence ratio, inlet mixture velocity, and channel width. Furthermore, some combustion characteristics, such as the rotating frequency of the single pelton-like flame and the triple flame, the radius of the stable circular flame front, and comparison between the major combustion products of the single and double pelton-like flames, were also investigated. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of electric fields on the propagation speed of tribrachial flames in coflow jets

The effect of electric fields on the propagation speed of tribrachial (or triple) flames has been investigated in a coflow jet by observing the transient flame propagation behavior after ignition. The propagation speed of tribrachial edges when no electric fields were applied showed typical behavior by having an inverse proportionality to the mixture fraction gradient at the flame edge. The behavior of flame propagation with electric fields was investigated by applying high voltage to the central fuel nozzle, thereby having a single-electrode configuration. The enhancement of propagation speed has been observed by varying the applied voltage and frequency for ac electric fields. The propagation speed of tribrachial flames was also investigated by applying positive and negative dc voltages to the nozzle, and similar improvements of the propagation speed were also observed. The propagation speeds of tribrachial flames in both the ac and dc electric fields correlated well with the electric field intensity, defined by the applied electric voltage divided by the distance between the nozzle electrode and the edge of the tribrachial flame. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Laser-induced radical generation and evolution to a self-sustaining flame

Images and emission spectra of sparks produced by laser-induced breakdown of methane and propane air mixtures were investigated with a high degree of spatial and temporal resolution. The laser-induced breakdown was generated by focusing a 532-nm nanosecond pulse from a Q-switched Nd:YAG laser. The data were collected using an intensified high-speed camera and a single/multi-fiber Cassegrain optics system coupled to an ICCD spectrometer. Emission spectra of OH{sup *}, CN{sup *}, CH{sup *}, and C{sup *}{sub 2} radicals were also collected using spectra boxes. The results provided information about the different stages of the laser-induced breakdown, with a specific focus on the transition from a flame kernel to a self-sustaining flame. The plasma shape and emission spectrum were very reproducible. The differences in the size of the flame kernel and the evolution of the radical emissions were analyzed for mixtures that fired or misfired. The impact of the level of radicals in the flame kernel was a critical parameter for the firing process, starting around 1 {mu}s after the laser-induced breakdown. The transition from plasma cooling to the classical chemical reactions in the combustion zone was analyzed. Even though the flame kernel size was directly linked to the spark energy, this was not a key parameter toward evolution to a self-sustaining flame. The Taylor blast wave theory was used to plot the location of the shock based on the evolution of the flame kernel size. The location was calculated using a laser-supported detonation model. A very good correlation was observed with the hot gas ignition process. Our results allowed us to obtain information about the process leading to firing or misfiring for similar environments, resulting in a better understanding of the laser breakdown phenomena and the means of utilizing this technique in an industrial context. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Propagation and extinction of premixed C{sub 5}-C{sub 12}n-alkane flames

Laminar flame speeds and extinction strain rates of premixed C{sub 5}-C{sub 12}n-alkane flames were determined at atmospheric pressure and elevated unburned mixture temperatures, over a wide range of equivalence ratios. Experiments were performed in the counterflow configuration and flow velocities were measured using Laser Doppler Velocimetry. The laminar flame speeds were obtained using a non-linear extrapolation technique utilizing numerical simulations of the counterflow experiments with detailed descriptions of chemical kinetics and molecular transport. Compared to linearly extrapolated values, the laminar flame speeds obtained using non-linear extrapolations were found to be 1-4 cm/s lower depending on the equivalence ratio. It was determined that the laminar flame speeds of all n-alkane/air mixtures considered in this investigation are similar to each other and sensitive largely to the H{sub 2}/CO and C{sub 1}-C{sub 4} hydrocarbon kinetics. Additionally, the resistance to extinction decreases as the fuel molecular weight increases. Simulations of the experiments were performed using the recently developed JetSurF 0.2 reaction model consisting of 194 species and 1459 reactions. The laminar flame speeds were predicted with good accuracy for all the n-alkane-air mixtures considered. The experimental extinction strain rates are well predicted by the model for fuel-lean mixtures. For stoichiometric and fuel-rich mixtures, the predicted extinction strain rates are approximately 10% lower than the experimental values. Insights into the physical and chemical processes that control the response of n-alkane flames are provided through detailed sensitivity analyses on both reaction rates and binary diffusion coefficients. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of radiation and compression on propagating spherical flames of methane/air mixtures near the lean flammability limit

Large discrepancies between the laminar flame speeds and Markstein lengths measured in experiments and those predicted by simulations for ultra-lean methane/air mixtures bring a great concern for kinetic mechanism validation. In order to quantitatively explain these discrepancies, a computational study is performed for propagating spherical flames of lean methane/air mixtures in different spherical chambers using different radiation models. The emphasis is focused on the effects of radiation and compression. It is found that the spherical flame propagation speed is greatly reduced by the coupling between thermal effect (change of flame temperature or unburned gas temperature) and flow effect (inward flow of burned gas) induced by radiation and/or compression. As a result, for methane/air mixtures near the lean flammability limit, the radiation and compression cause large amounts of under-prediction of the laminar flame speeds and Markstein lengths extracted from propagating spherical flames. Since radiation and compression both exist in the experiments on ultra-lean methane/air mixtures reported in the literature, the measured laminar flame speeds and Markstein lengths are much lower than results from simulation and thus cannot be used for kinetic mechanism validation. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Spatiotemporal flame propagations, combustion and solid particle emissions from lean and stoichiometric gasoline direct injection engine operation

Increased particle number and mass emissions in gasoline direct injection (GDI) engines should require to investigate in-cylinder flame and combustion characteristics associated with primary source of particle emissions. In this article, in-cylinder spatiotemporal flame luminosity is quantitatively characterized to features combustion process and solid particle emissions from a GDI engine operating in two lean and one stoichiometric modes. Low- and high-steady state operating points were used to compare combustion strategies on flame development and emission characteristics. A fiber-optic sensor composed of eight measurement channels detected the flame front and the direction of the flame propagation in the combustion chamber. Solid particle emissions in the exhaust were measured using an engine exhaust particle sizer and a micro soot sensor. Results of the experiments showed that two lean combustion modes by injection strategies resulted in distinct combustion and flame development. Lean combustion modes generated high diffusion flame by burning stratified rich-mixture. Although the lean cases resulted in strong diffusion flames, the lean-homogeneous produced similar particle size distributions with the stoichiometric mode with high ash particles. Piston pool fires on the piston surface in the lean-stratified mode induced a large accumulation mode with high particle mass concentrations.

42 ENGINEERING↗

Modeling stratified flames with and without shear using multiple mapping conditioning

A stochastic sparse particle approach is coupled with an artificial thickening flame (ATF) model for large eddy simulations (LES) to predict a series of turbulent premixed-stratified flames with and without shear and stratification. The thickened reaction progress variable serves as reference variable for the multiple mapping conditioning (MMC) mixing model which emulates turbulent mixing of the stochastic particles. The key feature of MMC is to enforce localness in this reference space when particle pairs are mixed and prevents unphysical mixing of burnt and unburnt fluid across the flame front. We apply MMC-ATF to three flames of a series of turbulent stratified flames and validate the method by comparison with experimental data. The new measurements feature increased accuracy in comparison to previously published data of the same flames due to a better signal-to-noise ratio and a setup which is less prone to beam steering. All flame locations are well predicted by the LES-ATF approach and an analysis of the MMC particle statistics demonstrates that MMC preserves the flamelet-like behaviour in regions where the experiments show low scatter around the flamelet solution. Predicted (local) deviations from the flamelet-solution are comparable to deviations observed in the measurements and variations in the flame structure due to differences in stratification and shear are reasonably well captured by the method.

47 OTHER INSTRUMENTATION↗

Rapid Flame-Annealed CuFe 2 O 4 as Efficient Photocathode for Photoelectrochemical Hydrogen Production

Copper ferrite (CuFe 2 O 4 ) possesses an indirect bandgap in the range of 1.54–1.95 eV. It is used as an attractive p-type photocathode in photoelectrochemical (PEC) water splitting, and theoretically it can yield a maximum photocurrent density of ~27 mA/cm 2 and a maximum solar-to-hydrogen conversion efficiency of ~33%. To date, only a few reports have been published on CuFe 2 O 4 photocathodes with very low-photocurrent densities, with a maximum value of 0.4 mA/cm2 at 0.4 V vs RHE. Herein, we prepared a CuFe 2 O 4 photocathode on FTO glass with the sol–gel method followed by either high-temperature flame annealing or furnace annealing. We found that the flame-annealed CuFe 2 O 4 photocathode generated a photocurrent density of 1.82 mA/cm 2 at 0.4 V vs RHE that is approximately 3.5 times higher than the furnace-annealed CuFe 2 O 4 (0.52 mA/cm 2 ). This photocurrent density is also higher than those of all the reported CuFe 2 O 4 photocathodes, and any Cu containing ternary oxide (Cu–M–O, M: Fe, Bi, V, and Nb) photocathode (0.1–1.3 mA/cm 2 at 0.4 V vs RHE). An improved PEC performance of the flame-annealed CuFe 2 O 4 photocathode is elicited owing to the beneficial effects of flame annealing on the physical, optical, and electrical properties of CuFe 2 O 4 . Flame annealing enhances the light absorption property of the CuFe 2 O 4 photocathode by slightly reducing the bandgap, and by forming a thicker film with increased porosity. Flame annealing also reduces the oxygen vacancy concentration in CuFe 2 O 4 , thus facilitating charge transport and interfacial charge transfer processes. Moreover, flame annealing requires only 16 min, which is much shorter than the time required for furnace annealing (~9 h). Furthermore, these results demonstrate that flame annealing is a rapid and effective means for fabricating metal oxide photoelectrodes with an enhanced PEC water splitting performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Large Eddy Simulation Modeling of Flashback and Flame Stabilization in Hydrogen-Rich Gas Turbines Using a Hierarchical Validation Approach

This project was a combined computational and experimental effort to improve predictive capability for boundary layer flashback of premixed swirl flames relevant to gas-turbine power plants operating with high-hydrogen-content fuels. During the course of this project, significant progress in modeling was made on four major fronts: 1) use of direct numerical simulation of turbulent flames to understand the coupling between the flame and the turbulent boundary layer; 2) improved modeling capability for flame propagation in stratified pre-mixtures; 3) improved portability of computer codes using the OpenFOAM platform to facilitate transfer to industry and other researchers; and 4) application of LES to flashback in swirl combustors, and a detailed assessment of its capabilities and limitations for predictive purposes. A major component of the project was an experimental program that focused on developing a rich experimental database of boundary layer flashback in swirl flames. Both methane and high-hydrogen fuels, including effects of elevated pressure (1 to 5 atm), were explored. For this project, a new model swirl combustor was developed. Kilohertz-rate stereoscopic PIV and chemiluminescence imaging were used to investigate the flame propagation dynamics. In addition to the planar measurements, a technique capable of detecting the instantaneous, time-resolved 3D flame front topography was developed and applied successfully to investigate the flow-flame interaction. The UT measurements and legacy data were used in a hierarchical validation approach where flows with increasingly complex physics were used for validation. First component models were validated with DNS and literature data in simplified configurations, and this was followed by validation with the UT 1-atm flashback cases, and then the UT high-pressure flashback cases. The new models and portable code represent a major improvement over what was available before this project was initiated.

42 ENGINEERING↗

Advanced Finite-Volume Numerics and Source Term Assumptions for Kernel and G-Equation Modelling of Propane/Air Flames

Here G-Equation models represent propagating flame fronts with an implicit two-dimensional surface representation (level-set). Level-set methods are fast, as transport source terms for the implicit surface can be solved with finite-volume operators on the finite-volume domain, without having to build the actual surface. However, they include approximations whose practical effects are not properly understood. In this study, we improved the numerics of the FRESCO CFD code’s G-Equation solver and developed a new method to simulate kernel growth using signed distance functions and the analytical sphere-mesh overlap. We analyzed their role for simulating propane/air flames, using three well-established constant-volume configurations: a one-dimensional, freely propagating laminar flame; a disc-shaped, constant-volume swirl combustor; and torch-jet flame development through an orifice from a two-chamber device. We tested the explicit (sub-cycled) vs. implicit formulation for the standard transport operators (advection, diffusion, compressibility). In addition to the accurate flame swept-volume method for chemistry and species source term, we developed a more accurate estimator for the burnt/unburnt split cell composition. Then, we developed a signed-distance-function (SDF) based method which provides a more stable reinitialization of the level-set field at every time-step. We found that simplifying assumptions common to several G-Equation implementations, for straightforward terms such as compressibility and advection, lead to large errors in predicting the propagation of even laminar flames, with deviations up to ~300% in simulated vs. formulated flame speed. Conversely, the enhanced numerics enabled through the SDF field reinitialization and improved chemistry source term improve simulation stability and smooth flame propagation even with significantly larger solver time-steps.

42 ENGINEERING↗

Flame characteristics of a NASA contra swirler module

Results are presented for an investigation of the structure of unconfined propane flames stabilized on a NASA contra-swirl can. General flame characterization, flame visualization by sodium chloride, temperature measurements, combustion products analysis, nitric oxide concentrations, and laser anemometer studies are considered. The results are discussed relative to sodium chloride visualization, temperature distributions, chemical composition of flames, nitric oxide distributions, and velocity distributions. It is shown that unconfined propane-air flames can be stabilized downstream of a NASA contra-swirl can under a wide range of airflow rates and fuel-air ratios. However, on increasing fuel input from the lowest at which flames can be stabilized, a compact recirculation zone-stabilized flame is formed. The effect of confinement on changes in flame shape and structure is determined.

Thompson, D.↗

Flashback flame arrester devices for fuel cargo tank vapor vents

The flame quenching capability of four types of flame arresting devices suitable for installation on fuel cargo tank vents of marine transport vessels is evaluated. A single 30 mesh screen, a dual 20 mesh screen, a spiral wound crimped metal ribbon, and a packed bed of ballast rings were tested. Flame speed and flame penetration of the test arresters were determined. Eight fuels representative of bulk cargoes were tested. The test arresters quenched a minimum of three flashback flames from all eight fuels, with one exception: high speed ethylene flames penetrated the dual 20 mesh screen on three tests. The arresters withstood the sustained flame from a propane/air mixture for 30 minutes. None of the arresters withstood the sustained flame from an ethylene/air mixture for more than 7 minutes.

Bjorklund, R. A.↗

Aerodynamic features of turbulent flames

The paper provides an interpretation for a variety of turbulent flame phenomena relating them to the aerodynamic properties of the flow field. This includes the classical notion of the breakdown of laminar flames propagation in ducts, the characteristic features of turbulent flame-fronts recorded by schlieren photography, as well as flame instabilities leading to flashback occurring in a combustion chamber behind a bluff-body flame holder. The rudimentary nature of turbulent flame propagation is shown to be associated with (1) vortex motion of a large-scale turbulent eddy, combined with (2) self-advancement of the flame at the appropriate normal burning speed and (3) the concomitant action of distributed sources of specific volume. The results furnish an insight into the macroscopic properties of the mechanism of turbulent flame propagation, rationalizing in particular its capability to sustain high flow velocities at relatively low normal burning speeds.

Oppenheim, A. K.↗

Effects of preferential diffusion on the burning intensity of curved flames

Using the Bunsen flame as a model curved flame, the coupled influence of preferential diffusion and flame stretch on the burning intensity of lean and rich mixtures of methane, propane, butane, ethylene, and hydrogen with air has been experimentally studied. The results substantiate theoretical predictions and quantify previous experimental observations that, for mixtures whose effective Lewis numbers (Le) are less than unity, the flame temperature is less than the adiabatic flame temperature. This temperature also decreases towards the flame tip, which has the largest curvature and therefore may locally extinguish. The dominance of diffusional transport in influencing the intensity of curved flames is demonstrated by showing that the tip opening of the highly diffusive hydrogen/air flames occurs at constant hydrogen equivalence ratios of about 1.15 to 1.20, being almost independent of the flow intensity and uniformity.

Mizomoto, M.↗