Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLAME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

The Influence of Pressure on Flame-Flow Characteristics of a Reacting Jet in Crossflow

This work experimentally investigates the effects of elevated combustor pressures on the characteristics of a lean premixed reacting methane/air jet injected into a lean vitiated crossflow using a 12.7 mm axial jet. Experiments were conducted in an axially staged combustor, which implements a reacting jet in crossflow (RJIC) configuration and operates over a pressure range of 1–5 atmospheres. Simultaneous CH* chemiluminescence and particle image velocimetry (PIV) are used to study the flow field and flame behavior. The results show that the reacting jet trajectory exhibits greater penetration with elevated pressure, which is a novel finding compared to available data in the literature. However, the flame liftoff point and ignition delay time both decreased with elevated pressure, which was attributed to decreased vorticity along the flame boundary which corresponds to increased Damköhler numbers (Da). Emissions measurements confirm the NOx increase with pressure as reported in the literature for single-stage gas turbine combustors. Concurrently, emission measurements for the staged configuration show the strong NOx benefit of the RJIC system: the data prove a reduction of global outlet emission levels at elevated pressure with the axially staged configuration. Here, the axial emission reduction was attributed to the decreasing liftoff at elevated pressure levels. Hence, the research emphasizes that the flame and emission characteristics are coupled; they are not only dependent on the geometric parameters and momentum flux ratios but are also a function of pressure.

03 NATURAL GAS↗

Turbulent flame-wall interaction: a DNS study

A turbulent flame-wall interaction (FWI) configuration is studied using three-dimensional direct numerical simulation (DNS) and detailed chemical kinetics. The simulations are used to investigate the effects of the wall turbulent boundary layer (i) on the structure of a hydrogen-air premixed flame, (ii) on its near-wall propagation characteristics and (iii) on the spatial and temporal patterns of the convective wall heat flux. Results show that the local flame thickness and propagation speed vary between the core flow and the boundary layer, resulting in a regime change from flamelet near the channel centreline to a thickened flame at the wall. This finding has strong implications for the modelling of turbulent combustion using Reynolds-averaged Navier-Stokes or large-eddy simulation techniques. Moreover, the DNS results suggest that the near-wall coherent turbulent structures play an important role on the convective wall heat transfer by pushing the hot reactive zone towards the cold solid surface. At the wall, exothermic radical recombination reactions become important, and are responsible for approximately 70% of the overall heat release rate at the wall. Spectral analysis of the convective wall heat flux provides an unambiguous picture of its spatial and temporal patterns, previously unobserved, that is directly related to the spatial and temporal characteristic scalings of the coherent near-wall turbulent structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An Investigation of the Flame-Burden Interaction during Remelting in an Experimental Aluminum Reverbatory Furnace

Flame impingement on the burden is routinely encountered during the initial phase of melting in aluminum reverberatory furnaces. This impingement causes an obstructed pathway for the hot gases, and hence the circulation and residence time of the hot gases are greatly impacted. Moreover, as the load melts, the flames gradually achieve an unobstructed path leading to reduced gas residence times. This flame impingement and constantly changing combustion space volume will lead to vastly different fuel and oxidizer mixing patterns and thus affect the overall furnace performance. Fine tuning the burner operating conditions such as flow rates and injection angles with the changing combustion space could result in significant improvements to the furnace efficiency. However, one has to gain a better understanding of the furnace dynamics to know the suitable parameters to adjust. Physical modeling can be elaborate and expensive to conduct on a regular basis while Computational Fluid Dynamics (CFD) can cost-effectively address this challenge. In this study, the furnace model is created with a particular loading pattern to understand the flame dynamics in the presence of a piled load. This configuration can be thought of as a computational model of the furnace with the burden at a particular stage of the melting process. Thermal efficiency and behavior of the furnace are quantified and the predicted values are compared with the operational data from an experimental reverberatory furnace.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Resolving Hysteresis in Perovskite Solar Cells with Rapid Flame-Processed Cobalt-Doped TiO 2

To further increase the open–circuit voltage ( V oc ) of perovskite solar cells (PSCs), many efforts have been devoted to doping the TiO 2 electron transport/selective layers by using metal dopants with higher electronegativity than Ti. However, those dopants can introduce undesired charge traps that hinder charge transport through TiO 2 , so the improvement in the V oc is often accompanied by an undesired photocurrent density–voltage ( J–V ) hysteresis problem. Herein, it is demonstrated that the use of a rapid flame doping process (40 s) to introduce cobalt dopant into TiO 2 not only solves the J–V hysteresis problem but also increases the V oc and power conversion efficiency of both mesoscopic and planar PSCs. The reasons for the simultaneous improvements are two fold. First, the flame–doped Co–TiO 2 film forms Co–O v (cobalt dopant–oxygen vacancy) pairs and hence reduces the number density of Ti 3+ trap states. Second, Co doping upshifts the band structure of TiO 2 , facilitating efficient charge extraction. As a result, for planar PSCs, the flame doping of Co increases the efficiency from 17.1% to 18.0% while reducing the hysteresis from 16.0% to 1.7%. Here, for mesoscopic PSCs, the flame doping of Co increases the efficiency from 18.5% to 20.0% while reducing the hysteresis from 7.0% to 0.1%.

36 MATERIALS SCIENCE↗

Flame aerosol synthesis of hollow alumina nanoshells for application in thermal insulation

Commercial implementation of hollow nanoshell materials is often limited by difficult scale-up and high cost. Here we present a scalable, continuous, and potentially low-cost route to hollow nanostructured materials using a High Temperature Reducing Jet flame aerosol reactor. The key advantage of this process over traditional flame aerosol synthesis methods is separation of flame chemistry and particle formation, which allows production of hollow nanoshells from an aqueous salt solution without any template or surfactant. We produced amorphous hollow alumina with an average diameter of 181 nm and shell thickness below 10 nm, and demonstrated the generality of the method by also producing hollow SiO 2 , ZrO 2 , Ga 2 O 3 , and Co 2 O 3 . We characterized the morphology, phase transition, thermal stability, and thermal conductivity of the flame-made hollow alumina by electron microscopy, x-ray diffraction, and thermal analysis methods. As a prototypical application, we incorporated hollow alumina into thermal insulation, combining it with common fiberglass insulation to reduce the thermal conductivity by 30% relative to pure fiberglass, to 0.028 W m -1 K -1 while maintaining robust fire-resistance and elasticity.

36 MATERIALS SCIENCE↗

On the low-frequency limit of flame transfer functions

The response of a premixed flame to quasi-steady flow perturbations is considered. It is found that in this low-frequency limit, constraints on the flame transfer function can be established from global conservation laws for mass, energy, and momentum. For example, the transfer function between velocity fluctuations and heat release of a perfectly premixed flame without fluctuations of equivalence ratio should be unity in the limit of zero frequency, while for a combustion system with constant mass flow rate of fuel, the transfer function should tend toward zero. It is demonstrated that these considerations can be employed to reduce the number of unknowns in analytical flame models or identify invalid modeling assumptions. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Formation of small PAHs in laminar premixed low-pressure propene and cyclopentene flames: Experiment and modeling

The formation of small PAHs with up to three rings has been studied in fuel-rich, nonsooting premixed flames of propene-oxygen-argon and cyclopentene-oxygen-argon at C/O=0.77 and 50 mbar. Detailed species composition and temperature profiles for these flames had been studied before, using laser-induced fluorescence (LIF) and in situ molecular beam mass spectrometry (MBMS) with electron impact ionization (EI). These previous studies found a significant influence of the fuel structure upon the reaction pathways to benzene as the first aromatic ring. Here, the further molecular reaction sequence is studied with enhanced sensitivity, using MBMS coupled with resonance-enhanced multiphoton ionization (REMPI). Absolute concentrations of benzene were determined using both ionization strategies in order to establish a link to the previous investigations. The ratio of REMPI signals in the two flames for masses from m/z=78 (benzene) up to approximately m/z=200 is given and shows a predominant tendency of the cyclopentene flame to form aromatic species. The experimental results are complemented with simulations using two current chemical kinetic reaction models. The model predictions for important species in this mass range are discussed in the light of reaction flux and sensitivity analyses. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Laser-induced fluorescence measurements of NCN in low-pressure CH{sub 4}/O{sub 2}/N{sub 2} flames and its role in prompt NO formation

NCN profiles were measured for five rich and lean premixed, low-pressure methane flames using laser-induced fluorescence (LIF). A semiquantitative determination of the NCN mole fractions as a function of spatial height above the burner is made by calibrating the NCN LIF signals using highly accurate OH LIF measurements in an adjacent spectral region. The resulting calibration yields an uncertainty estimate of a factor of 3 for the absolute values, but only {+-}25% for the relative NCN profiles. For all flame conditions, the NCN profiles occur immediately downstream of previously measured CH profiles. In addition, high correlations are found between the peak CH and peak NCN concentrations and the peak NCN and postflame NO concentrations over all equivalence ratios. These observations are consistent with NCN being the primary product channel from the CH + N{sub 2} reaction and the initial intermediate in the prompt NO formation. This is the first mechanistic study in hydrocarbon flames that provides such experimental evidence. The experimental profiles are compared to numerical calculations using modified versions of two well-established hydrocarbon kinetic mechanisms. Reasonable agreement between the calculations and experiment is found for NCN profile shape, location of peak NCN concentrations, and absolute mole fractions. However, the dependence on stoichiometry of the peak NCN concentration is overestimated. Further work is required on NCN kinetics for modeling prompt NO in laminar premixed flames. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Diode laser absorption measurement and analysis of HCN in atmospheric-pressure, fuel-rich premixed methane/air flames

Measurements of HCN in flat, fuel-rich premixed methane/air flames at atmospheric pressure are reported. Quartz-microprobe sampling followed by wavelength modulation absorption spectroscopy with second harmonic detection was used to obtain an overall measurement uncertainty of better than 20% for mole fractions HCN on the order of 10 ppm. The equivalence ratio, {phi}, was varied between 1.3 and 1.5, while the flame temperature was varied independently by changing the mass flux through the burner surface at constant equivalence ratio. Under the conditions of the experiments, the peak mole fractions vary little, in the range of 10-15 ppm. Increasing the flame temperature by increasing the mass flux had little influence on the peak mole fraction, but accelerated HCN burnout substantially. At high equivalence ratio and low flame temperature, HCN burnout is very slow: at {phi}=1.5, {proportional_to}10ppm HCN is still present 7 mm above the burner surface. Substantial quantitative disagreement is observed between the experimental profiles and those obtained from calculations using GRI-Mech 3.0, with the calculations generally overpredicting the results significantly. Changing the rates of key formation and consumption reactions for HCN can improve the agreement, but only by making unreasonable changes in these rates. Inclusion of reactions describing NCN formation and consumption in the calculations improves the agreement with the measurements considerably. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Soot volume fraction measurement in low-pressure methane flames by combining laser-induced incandescence and cavity ring-down spectroscopy: Effect of pressure on soot formation

Soot volume fraction (f{sub v}) profiles are recorded in low-pressure methane/oxygen/nitrogen flat flames using laser-induced incandescence (LII). Experiments are performed from 20 to 28 kPa in flames having the same equivalence ratio (2.32). Calibration is performed by cavity ring-down spectroscopy (CRDS) and indicates a very weak soot volume fraction (0.066 ppb at 21.33 kPa and 0.8 ppb at 26.66 kPa in the burnt gases). Soot volume fraction is found to increase continuously after a given distance above the burner (HAB) and tends to level off in the burnt gases. The reaction time resolution available in low-pressure flames makes it possible to examine the early steps of soot formation. The variation of the LII signal with laser energy before the LII ''plateau'' region is much weaker at the beginning of soot formation than after a given reaction time. The LII time decays are nearly constant within the first millimetres, whereas an increase in the decay, correlated with the growth of the primary soot particle, is observed later. The growth of soot volume fraction is then analysed by considering the variation of the derivative function df{sub v}/dt with f{sub v}. Three regimes having respectively a positive slope, a constant slope, and a negative slope are observed and are interpreted with respect to the soot inception process. Finally, a very important sensitivity of f{sub v} with pressure P (at 30 mm HAB) is observed, leading to a power law, f{sub v}=KP{sup 11}, confirmed by extinction measurements (by CRDS). The observed dependence of f{sub v} with pressure could be a result of the prominence of the early soot inception process in the investigated low-pressure flames. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On evolution of particle size distribution functions of incipient soot in premixed ethylene-oxygen-argon flames

The evolution of the soot particle size distribution function (PSDF) and particle morphology are studied for premixed ethylene-oxygen-argon flat flames at equivalence ratio {phi}=2.07 over the maximum flame temperature range of 1600-1900 K. Experiments were carried out using an in-situ probe sampling method in tandem with a scanning mobility particle sizer (SMPS), yielding the PSDF for various distances from the burner surface. The morphology of the particles was examined by transmission electron microscopy (TEM) and atomic force microscopy (AFM). Within the particle size range that can be detected, the PSDF transitions from an apparent unimodal PSDF for high temperature flames (T{sub f}>{proportional_to}1800 K) to a bimodal PSDF at lower temperatures (T{sub f}<{proportional_to}1800 K). The bimodal PSDF has a noticeable trough that separates the nucleation tail and log-normal mode. This mode-transition trough had been previously thought to occur at a fixed particle size, but these results show a continuous shift of the trough location towards smaller sizes with increasing flame temperature. TEM images show that the particles are spherical, even when the PSDF is bimodal, suggesting that the bimodality occurs as the primary particles undergoes mass and size growth, and is not a result of particle aggregation. Atomic force microscopy of substrate deposited particles shows that particles spread and form hill like structures upon impact with the substrate surface, indicating that the particles are liquid-like at the time of impact. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of Lewis number on turbulent scalar transport and its modelling in turbulent premixed flames

The behaviour of the turbulent scalar flux in premixed flames has been studied using Direct Numerical Simulation (DNS) with emphasis on the effects of Lewis number in the context of Reynolds-averaged closure modelling. A database was obtained from DNS of three-dimensional freely propagating statistically planar turbulent premixed flames with simplified chemistry and a range of global Lewis numbers from 0.34 to 1.2. Under the same initial conditions of turbulence, flames with low Lewis numbers are found to exhibit counter-gradient transport, whereas flames with higher Lewis numbers tend to exhibit gradient transport. The Reynolds-averaged transport equation for the turbulent scalar flux is analysed in detail and the performance of existing models for the unclosed terms is assessed with respect to corresponding quantities extracted from DNS data. Based on this assessment, existing models which are able to address the effects of non-unity Lewis number on turbulent scalar flux transport are identified, and new or modified models are suggested wherever necessary. In this way, a complete set of closure models for the scalar flux transport equation is prescribed for use in Reynolds-Averaged Navier-Stokes simulations. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electric fields effect on liftoff and blowoff of nonpremixed laminar jet flames in a coflow

The stabilization characteristics of liftoff and blowoff in nonpremixed laminar jet flames in a coflow have been investigated experimentally for propane fuel by applying AC and DC electric fields to the fuel nozzle with a single-electrode configuration. The liftoff and blowoff velocities have been measured by varying the applied voltage and frequency of AC and the voltage and the polarity of DC. The result showed that the AC electric fields extended the stabilization regime of nozzle-attached flame in terms of jet velocity. As the applied AC voltage increased, the nozzle-attached flame was maintained even over the blowout velocity without having electric fields. In such a case, a blowoff occurred directly without experiencing a lifted flame. While for the DC cases, the influence on liftoff was minimal. There existed three different regimes depending on the applied AC voltage. In the low voltage regime, the nozzle-detachment velocity of either liftoff or blowoff increased linearly with the applied voltage, while nonlinearly with the AC frequency. In the intermediate voltage regime, the detachment velocity decreased with the applied voltage and reasonably independent of the AC frequency. At the high voltage regime, the detachment was significantly influenced by the generation of discharges. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NCN detection in atmospheric flames

The first extensive spectra of NCN in atmospheric pressure flames are reported, as well as qualitative planar LIF images of its spatial distribution. The spectra have been recorded by LIF in lifted, fuel-rich CH4/N2O/N2 and CH4/air flames, and are compared to simulations. In the CH4/air flames, the NCN LIF signal peaks around {phi} = 1.2. Planar LIF imaging illustrates the very confined NCN distribution in the CH4/N2O/N2 flame.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Demonstration of a burner for the investigation of partially premixed low-temperature flames

A burner, which stabilizes near-one-dimensional low-temperature flames at atmospheric pressure, was designed to access the combustion regime near 1500 K for quantitative species diagnostics. Combustion temperatures between 1300 and 1800 K in argon-diluted methane-oxygen flames were achieved by preheating the burner and adapting the inert gas flow. Mass spectrometry with electron ionization was used to determine mole fractions profiles of reactants, products, and intermediates. Combustion parameters were varied including stoichiometry, diluent mole fraction and preheat temperature. Mole fraction profiles resemble those taken in regular premixed flat flames. A number of C{sub 1}- and C{sub 2}-intermediates as well as some oxygenated species were identified. Higher-mass species (m/z > 42) were not detected in the low-temperature methane-oxygen flames which contain 90% argon in the cold gases. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of diffusion flames for synthesis of single-walled carbon nanotubes

Recent studies have shown that Fe/Si/O catalysts on the fuel side of an oxygen-enriched inverse diffusion flame produce micron-length single-walled carbon nanotubes at rapid rates (>100{mu}m/s). Despite the favorable catalyst/flame interaction for nanotube nucleation and growth, the catalyst lifetimes are only a few milliseconds. To increase catalyst lifetime and hence, carbon nanotube length, it is necessary to know how the local environment changes as the catalyst moves through the flame. A 2-D computational fluid dynamics model with detailed chemistry is employed to investigate the nature of the flame environment along various catalyst trajectories. The results indicate that temperature and species concentrations do not change significantly along individual catalyst trajectories, although not all trajectories experience the same environment due to the steep gradients in the radial direction. On the other hand, analysis of catalyst particle composition before and after nanotube growth shows that catalyst oxygen content decreases significantly during nanotube growth. This change in catalyst composition could affect the relative rates of carbon supply versus removal from the catalyst surface, such that carbon encapsulation and thus poisoning of the catalyst is favored after sufficient time. The results of this work indicate that catalyst deactivation, not a changing catalyst environment, is responsible for rapid encapsulation of the catalyst by amorphous carbon and thus, the short catalyst lifetimes observed in oxygen-enriched diffusion flames. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mixing and stabilization study of a partially premixed swirling flame using laser induced fluorescence

A laboratory-scale swirling burner, presenting many similarities with gas turbines combustors, has been studied experimentally using planar laser induced fluorescence (PLIF) on OH radical and acetone vapor in order to characterize the flame stabilization process. These diagnostics show that the stabilization point rotates in the combustion chamber and that air and fuel mixing is not complete at the end of the mixing tube. Fuel mass fraction decays exponentially along the mixing tube axis and transverse profiles show a gaussian shape. However, radial pressure gradients tend to trap the fuel in the core of the vortex that propagates axially in the mixing tube. As the mixing tube vortex enters the combustion chamber, vortex breakdown occurs through a precessing vortex core (PVC). The axially propagating vortex shows a helicoidal trajectory in the combustion chamber which trace is observed with transverse acetone PLIF. As a consequence, the stabilizing point of the flame in the combustion chamber rotates with the PVC structure. This phenomenon has been observed in the present study with a high speed camera recording spontaneous emission of the flame. The stabilization point rotation frequency tends to increase with mass flow rates. It was also shown that the coupling between the PVC and the flame stabilization occurs via mixing, explaining one possible coupling mechanism between acoustic waves in the flow and the reaction rate. This path may also be envisaged for flashback, an issue that will be more completely treated in a near future. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Numerical investigation of spontaneous flame propagation under RCCI conditions

This paper presents results from one and two-dimensional direct numerical simulations under Reactivity Controlled Compression Ignition (RCCI) conditions of a primary reference fuel (PRF) mixture consisting of n-heptane and iso-octane. RCCI uses in-cylinder blending of two fuels with different autoignition characteristics to control combustion phasing and the rate of heat release. These simulations employ an improved model of compression heating through mass source/sink terms developed in a previous work by Bhagatwala et al. (2014), which incorporates feedback from the flow to follow a predetermined experimental pressure trace. Two-dimensional simulations explored parametric variations with respect to temperature stratification, pressure profiles and n-heptane concentration. Furthermore, statistics derived from analysis of diffusion/reaction balances locally normal to the flame surface were used to elucidate combustion characteristics for the different cases. Both deflagration and spontaneous ignition fronts were observed to co-exist, however it was found that higher n-heptane concentration provided a greater degree of flame propagation, whereas lower n-heptane concentration (higher fraction of iso-octane) resulted in more spontaneous ignition fronts. A significant finding was that simulations initialized with a uniform initial temperature and a stratified n-heptane concentration field, resulted in a large fraction of combustion occurring through flame propagation. The proportion of spontaneous ignition fronts increased at higher pressures due to shorter ignition delay when other factors were held constant. For the same pressure and fuel concentration, the contribution of flame propagation to the overall combustion was found to depend on the level of thermal stratification, with higher initial temperature gradients resulting in more deflagration and lower gradients generating more ignition fronts. Statistics of ignition delay are computed to assess the Zel’dovich (1980) theory for the mode of combustion propagation based on ignition delay gradients.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗