Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Two-phase choked flow of subcooled nitrogen through a slit

Two-phase choked flow rate and pressure distribution data are reported for subcooled nitrogen flowing through a slit. The slip was a narrow rectangular passage of equal length and width. The inlet stagnation pressure ranged from slightly above saturation to twice the thermodynamic critical pressure. Four stagnation isotherms were investigated covering a range which spanned the critical temperature. The results suggested a uniform two-phase flow pattern with vaporization occurring at or near the exit in most cases. The results compared favorably with the theory of Henry for nonequilibrium subcooled two-phase choked flow in long tubes.

Simoneau, R. J.↗
NASA NTRS1973

Experimental study of supersonic laminar base flow with and without suction

Heat-transfer and pressure distributions in laminar separated flows downstream of rearward-facing steps with and without mass suction were investigated at Mach numbers around 4 for the conditions when the boundary-layer thickness was comparable to or larger than the step height. In both suction and no-suction cases, an increase of the step height resulted in a sharp drop of the base heating rates, which then gradually recovered to less than or near attached-flow values obtained with flat-plate configuration. Mass suction from the step base area increased the local heating rates; this effect, however, was relatively weak for laminar flows tested, and the competing effect of the step height clearly predominated. It was found that even removal of the entire incoming boundary layer was not sufficient to raise the poststep heating rates above the flat-plate values. The base pressure in the no-suction, solid-step case correlated reasonably well with the step height-to-boundary-layer thickness ratio and with the Reynolds number based on the step height.

Jakubowski, A. K.↗
NASA NTRS1974

Two-phase choked flow of subcooled nitrogen through a slit

Two-phase choked flow rate and pressure distribution data are reported for subcooled nitrogen flowing through a slit. The slit was a narrow rectangular passage of equal length and width. The inlet stagnation pressure ranged from slightly above saturation to twice the thermodynamic critical pressure. Four stagnation isotherms were investigated, covering a range which spanned the critical temperature. The results suggested a uniform two-phase flow pattern with vaporization occurring at or near the exit in most cases. The results compared favorably with the theory of Henry (1970) for nonequilibrium subcooled two-phase choked flow in long tubes.

Simoneau, R. J.↗
NASA NTRS1992

An experimental study of oscillatory thermocapillary convection in cylindrical containers

An experimental study of oscillatory thermocapillary in small cylindrical containers with a heating wire placed along the center axis is performed by investigating the flow structures and temperature distributions under various conditions. To supplement the flow visualization the surface is scanned using an infrared imager. Here, 2 cS viscosity (Pr = 27) silicone oil is used as the test fluid. It is observed that beyond a certain temperature difference between the container wall and the heating wire, a distinctive unsteady flow pattern appears. This unsteady phenomenon is identified as oscillatory thermocapillary. After the onset of oscillations the flow structure becomes nonaxisymmetric and wave motion is observed at the free surface. It is shown that the critical temperature difference is independent of container dimensions if the aspect ratio is fixed.

Kamotani, Y.↗
NASA NTRS1998

Mixing of Multiple Jets With a Confined Subsonic Crossflow

Results from a recently completed enhanced mixing program are summarized in the two technical papers. These studies were parts of a High Speed Research (HSR)-supported joint Government/industry/university program that involved, in addition to the NASA Lewis Research Center, researchers at United Technologies Research Center, Allison Engine Company, CFD Research Corporation, and the University of California, Irvine. The studies investigated the mixing of jets injected normal to a confined subsonic mainsteam in both rectangular and cylindrical ducts. Experimental and computational studies were performed in both nonreacting and reacting flows. The orifice geometries and flow conditions were selected as typical of the complex three-dimensional flows in the combustion chambers in low-emission gas turbine engines. The principal conclusion from both the experiments and modeling was that the momentum-flux ratio J and orifice spacing S/H were the most significant flow and geometry variables, respectively. Conserved scalar distributions were similar-independent of reaction, orifice diameter H/d, and shape-when the orifice spacing and the square root of the momentum-flux ratio were inversely proportional. Jet penetration was critical, and penetration decreased as either momentum-flux ratio or orifice spacing decreased. We found that planar averages must be considered in context with the distributions. The mass-flow ratios and the orifices investigated were often very large. The jet-to-mainstream mass-flow ratio was varied from significantly less than 1 to greater than 1. The orifice-area to mainstream-cross-sectional-area was varied from approx. 0 to 0.5, and the axial planes of interest were often just downstream of the orifice trailing edge. Three-dimensional flow was a key part of efficient mixing and was observed for all configurations. As an example of the results, the accompanying figure shows the effects of different rates of mass addition on the opposite walls of a rectangular duct.

Holdeman, James D.↗
NASA NTRS1998

Measurements of Heat Transfer, Flow, and Pressures in a Simulated Turbine Blade Internal Cooling Passage

An experimental study was made to obtain quantitative information on heat transfer, flow, and pressure distribution in a branched duct test section that had several significant features of an internal cooling passage of a turbine blade. The objective of this study was to generate a set of experimental data that could be used for validation of computer codes that would be used to model internal cooling. Surface heat transfer coefficients and entrance flow conditions were measured at nominal entrance Reynolds numbers of 45,000, 335,000, and 726,000. Heat transfer data were obtained by using a steady-state technique in which an Inconel heater sheet is attached to the surface and coated with liquid crystals. Visual and quantitative flow-field data from particle image velocimetry measurements for a plane at midchannel height for a Reynolds number of 45,000 were also obtained. The flow was seeded with polystyrene particles and illuminated by a laser light sheet. Pressure distribution measurements were made both on the surface with discrete holes and in the flow field with a total pressure probe. The flow-field measurements yielded flow-field velocities at selected locations. A relatively new method, pressure sensitive paint, was also used to measure surface pressure distribution. The pressure paint data obtained at Reynolds numbers of 335,000 and 726,000 compared well with the more standard method of measuring pressures by using discrete holes.

Russell, Louis M.↗
NASA NTRS1980

An analysis method for multi-component airfoils in separated flow

The multi-component airfoil program (Langley-MCARF) for attached flow is modified to accept the free vortex sheet separation-flow model program (Analytical Methods, Inc.-CLMAX). The viscous effects are incorporated into the calculation by representing the boundary layer displacement thickness with an appropriate source distribution. The separation flow model incorporated into MCARF was applied to single component airfoils. Calculated pressure distributions for angles of attack up to the stall are in close agreement with experimental measurements. Even at higher angles of attack beyond the stall, correct trends of separation, decrease in lift coefficients, and increase in pitching moment coefficients are predicted.

Rao, B. M.↗
NASA NTRS1974

Experimental study of sharp and blunt nose streamwise corners at Mach 20

Extensive heat transfer and pressure distribution data and oil flow studies on sharp and blunt-nose streamwise corners at Mach 20 in helium are presented. The far corner boundary layers on the wedge surfaces forming the corners are laminar for most test conditions. Analysis of the data indicates that the corner flow field geometry can be described in terms of the inviscid shock pattern on the two dimensional surfaces forming the corner. Parameters used to correlate blunt shock growth can be used to correlate features of the flow field observed in oil flow photographs in addition to the measured pressure and heat transfer distributions on the models. The flow field structure is described from available experimental data. Regions of the flow in which the structure still is not known are discussed.

Watson, R. D.↗
NASA NTRS1993

Development of separation due to interaction between a shock wave and a turbulent boundary layer perturbed by rarefaction waves

The interaction of a turbulent boundary layer with rarefaction and shock waves in flows past inclined steps was investigated experimentally and theoretically. The experiments were carried out in supersonic wind tunnels with test sections of 0.6 x 0.6 m and 0.2 x 0.2 m, with adiabatic conditions on the surface model. Based on detailed measurements of pressure fields, velocity, and surface friction, combined with results of optical visualization and analysis of limiting flow lines, three characteristic flow regimes are identified. These are (1) nonseparated flow at small step angles, (2) formation of a local separation zone with a free separation point at moderate step angles, and (3) formation of a large-scale separated flow with a fixed separation point at sufficiently large step angles. The quantitative gasdynamic schemes and surface pressure distributions for these flow regimes are shown for Mach 2.85.

Zheltovodov, A. A.↗
NASA NTRS1959

A Systematic Kernel Function Procedure for Determining Aerodynamic Forces on Oscillating or Steady Finite Wings at Subsonic Speeds

Details are given of a numerical solution of the integral equation which relates oscillatory or steady lift and downwash distributions in subsonic flow. The procedure has been programmed for the IBM 704 electronic data processing machine and yields the pressure distribution and some of its integrated properties for a given Mach number and frequency and for several modes of oscillation in from 3 to 4 minutes, results of several applications are presented.

Watkins, Charles E.↗
NASA NTRS1999

Hypersonic Flow Control Using Upstream Focused Energy Deposition

A numerical study of centerline and off-centerline power deposition at a point upstream of a two-dimensional blunt body at Mach 6.5 at 30 km altitude are presented. The full Navier-Stokes equations are used. Wave drag, lift, and pitching moment are presented as a function of amount of power absorbed in the flow and absorption point location. It is shown that wave drag is considerably reduced. Modifications to the pressure distribution in the flow field due to the injected energy create lift and a pitching moment when the injection is off-centerline. This flow control concept may lead to effective ways to improve the performance and to stabilize and control hypersonic vehicles.

Riggins David W.↗
NASA NTRS1990

Mobility power flow analysis of an L-shaped plate structure subjected to distributed loading

An analytical investigation based in the Mobility Power Flow (MPF) method is presented for the determination of the vibrational response and power flow for two coupled flat plate structures in an L-shaped configuration, subjected to distributed excitation. The principle of the MPF method consists of dividing the global structure into a series of subsystems coupled together using mobility functions. Each separate subsystem is analyzed independently to determine the structural mobility functions for the junction and excitation locations. The mobility functions, together with the characteristics of the junction between the subsystems, are then used to determine the response of the global structure and the MPF. In the considered coupled plate structure, MPF expressions are derived for distributed mechanical excitation which is independent of the structure response. However using a similar approach with some modifications excitation by an acoustic plane wave can be considered. Some modifications are required to deal with the latter case are necessary because the forces (acoustic pressure) acting on the structure are dependent on the response of the structure due to the presence of the scattered pressure.

Cuschieri, J. M.↗
NASA NTRS1991

The discovery of large amounts of cold, X-ray absorbing matter in cooling flows

The discovery of significant excess absorption in the X-ray spectra of 12 clusters of galaxies is reported. The spectra also require a cooling-flow component, which confirms the results of imaging studies of the clusters showing the strongly peaked emission characteristic of cooling flows. The total mass of absorbing gas is determined on the assumption that it is distributed through the cooling flow region and has cosmic abundance. It is shown that the gas is most likely in the form of small cold clouds. The excess absorption is interpreted as being due to photoelectric absorption in cold gas clouds distributed through the cooling flows.

White, D. A.↗
NASA NTRS2001

Three-Dimensional Simulations of Mantle Convection in Io

Io has very high surface heat flow and an abundance of volcanic activity, which are thought to be driven by nonuniform tidal heating in its interior. This nonuniform heat is transported to the base of the lithosphere by very vigorous convection in Io's silicate mantle, the form of which is presumably responsible for the distribution of surface features such as volcanoes and mountains. We here present three-dimensional spherical calculations of mantle convection in Io, in order to ascertain the likely form of this convection and the resulting distribution of heat flow at the surface and core-mantle boundary. Different models of tidal dissipation are considered: the endmember scenarios (identified by M. N. Ross and G. Schubert) of dissipation in the entire mantle, or dissipation in a thin (approximately 100-km-thick) asthenosphere, as well as the 'preferred' distribution of M. N. Ross et al. comprising 1/3 mantle and 2/3 asthenosphere heating. The thermal structure of Io's mantle and asthenosphere is found to be strongly dependent on tidal heating mode, as well as whether the mantle-asthenosphere boundary is permeable or impermeable. Results indicate a large-scale flow pattern dominated by the distribution of tidal heating, with superimposed small-scale asthenospheric instabilities that become more pronounced with increasing Rayleigh number. These small-scale instabilities spread out the surface heat flux, resulting in smaller heat flux variations with increasing Rayleigh number. Scaled to Io's Rayleigh number of O(10(exp 12)) variations of order a few percent are expected. This small but significant variation in surface heat flux may be compatible with the observed distributions of volcanic centers and mountains, which appear fairly uniform at first sight but display a discernible distribution when suitably processed. The observed distribution of volcanic centers is similar to the asthenosphere heating distribution, implying that most of the tidal heating in Io occurs in an asthenosphere.

Tackley, Paul J.↗
NASA NTRS1978

Velocity, temperature, and electrical conductivity profiles in hydrogen-oxygen MHD duct flows

This paper presents results of two-dimensional duct flow computations for radial distributions of velocity, temperature, and electrical conductivity. Calculations were carried out for the flow conditions representative of NASA Lewis hydrogen-oxygen combustion driven MHD duct. Results are presented for two sets of computations: (1) profiles of developing flow in a smooth duct, and (2) profiles of fully developed pipe flow with a specified streamwise shear stress distribution. The predicted temperature and electrical conductivity profiles for the developing flows compared well with available experimental data.

Greywall, M. S.↗