Search NASA⌕ Search

SEARCH · Search NASA

Results for “HYPERSONIC SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

The Performance of a Subsonic Diffuser Designed for High Speed Turbojet-Propelled Flight

An initial-phase subsonic diffuser has been designed for the turbojet flowpath of the hypersonic x43B flight demonstrator vehicle. The diffuser fit into a proposed mixed-compression supersonic inlet system and featured a cross-sectional shape transitioning flowpath (high aspect ratio rectangular throat-to-circular engine face) and a centerline offset. This subsonic diffuser has been fabricated and tested at the W1B internal flow facility at NASA Glenn Research Center. At an operating throat Mach number of 0.79, baseline Pitot pressure recovery was found to be just under 0.9, and DH distortion intensity was about 0.4 percent. The diffuser internal flow stagnated, but did not separate on the offset surface of this initial-phase subsonic diffuser. Small improvements in recovery (+0.4 percent) and DH distortion (-32 percent) were obtained from using vane vortex generator flow control applied just downstream of the diffuser throat. The optimum vortex generator array patterns produced inflow boundary layer divergence (local downwash) on the offset surface centerline of the diffuser, and an inflow boundary layer convergence (local upwash) on the centerline of the opposite surface.

Biesiadny, Thomas J.↗
NASA NTRS2011

Mars Exploration Rover Heat Shield Recontact Analysis

The twin Mars Exploration Rover missions landed successfully on Mars surface in January of 2004. Both missions used a parachute system to slow the rover s descent rate from supersonic to subsonic speeds. Shortly after parachute deployment, the heat shield, which protected the rover during the hypersonic entry phase of the mission, was jettisoned using push-off springs. Mission designers were concerned about the heat shield recontacting the lander after separation, so a separation analysis was conducted to quantify risks. This analysis was used to choose a proper heat shield ballast mass to ensure successful separation with low probability of recontact. This paper presents the details of such an analysis, its assumptions, and the results. During both landings, the radar was able to lock on to the heat shield, measuring its distance, as it descended away from the lander. This data is presented and is used to validate the heat shield separation/recontact analysis.

Raiszadeh, Behzad↗
NASA NTRS2021

Hypersonic Boundary-Layer Transition on Blunted Cones at Angle of Attack

Experimental studies of cones at several high-speed facilities have demonstrated that, for small nosetip bluntness, transition onset over a circular cone moves upstream along the leeward side and downstream along the windward side, but this trend may be reversed at large bluntness values, where transition onset moves downstream along the leeward side and upstream along the windward side. A theoretical and numerical investigation is performed to characterize the effects of nose bluntness on disturbance amplification over the circular cone for several angles of attack, with the goal of understanding the potential physical mechanisms behind the experimental observations. The three-dimensional laminar basic states over a 1.5 m long, 7-degree half-angle cone with 9.525 mm nosetip radius are computed for selected angles of attack values and freestream conditions that are selected to match the Mach 10 experiments conducted within the Hypervelocity Wind Tunnel 9 at the Arnold Engineering Development Complex (AEDC). The solutions at a freestream unit Reynolds number of 17.1 million per meter are used to perform detailed instability analyses for angles of attack equal to 0, 1, 3, and 5 degrees. Results indicate that the linear amplification of stationary crossflow waves along inflection lines may begin to influence transition along the acreage of the cone for angles of attack equal to or larger than 5 degrees. The measured trend in transition front with respect to increasing angle of attack is found to be consistent with the predicted increase in the amplification factors for Mack mode disturbances along the streamline trajectories. The increase in Mack mode amplification along the windward ray for higher angles of attack is shown to be the result of a progressively earlier entropy-layer swallowing. Computations also indicate that the transition amplification factor along the windward ray is not constant and increases with the angle of attack and that the transition #-factors along the leeward ray are rather small. The nonmodal analysis for zero degrees angle of attack shows that entropy-layer disturbances with appreciably strong energy growth can coexist with Mack mode instabilities at the measured transition location.

boundary layer transition↗
NASA NTRS2021

Hypersonic Boundary-Layer Transition on Blunted Cones at Angle of Attack

Experimental studies of cones at several high-speed facilities have demonstrated that, for small nosetip bluntness, transition onset over a circular cone moves upstream along the leeward side and downstream along the windward side, but this trend may be reversed at large bluntness values, where transition onset moves downstream along the leeward side and upstream along the windward side. A theoretical and numerical investigation is performed to characterize the effects of nose bluntness on disturbance amplification over the circular cone for several angles of attack, with the goal of understanding the potential physical mechanisms behind the experimental observations. The three-dimensional laminar basic states over a 1.5 m long, 7-degree half-angle cone with 9.525 mm nosetip radius are computed for selected angles of attack values and freestream conditions that are selected to match the Mach 10 experiments conducted within the Hypervelocity Wind Tunnel 9 at the Arnold Engineering Development Complex (AEDC). The solutions at a freestream unit Reynolds number of 17.1 million per meter are used to perform detailed instability analyses for angles of attack equal to 0, 1, 3, and 5 degrees. Results indicate that the linear amplification of stationary crossflow waves along inflection lines may begin to influence transition along the acreage of the cone for angles of attack equal to or larger than 5 degrees. The measured trend in transition front with respect to increasing angle of attack is found to be consistent with the predicted increase in the amplification factors for Mack mode disturbances along the streamline trajectories. The increase in Mack mode amplification along the windward ray for higher angles of attack is shown to be the result of a progressively earlier entropy-layer swallowing. Computations also indicate that the transition amplification factor along the windward ray is not constant and increases with the angle of attack and that the transition #-factors along the leeward ray are rather small. The nonmodal analysis for zero degrees angle of attack shows that entropy-layer disturbances with appreciably strong energy growth can coexist with Mack mode instabilities at the measured transition location.

Boundary Layer Transition↗
NASA NTRS1976

Study of a fail-safe abort system for an actively cooled hypersonic aircraft. Volume 1: Technical summary

Conceptual designs of a fail-safe abort system for hydrogen fueled actively cooled high speed aircraft are examined. The fail-safe concept depends on basically three factors: (1) a reliable method of detecting a failure or malfunction in the active cooling system, (2) the optimization of abort trajectories which minimize the descent heat load to the aircraft, and (3) fail-safe thermostructural concepts to minimize both the weight and the maximum temperature the structure will reach during descent. These factors are examined and promising approaches are evaluated based on weight, reliability, ease of manufacture and cost.

Pirello, C. J.↗
NASA NTRS1978

Aerodynamic characteristics at Mach 6 of a wing-body concept for a hypersonic research airplane

The static aerodynamic characteristics of a 1/30 scale model of a wing-body concept for a high speed research airplane were investigated in the Langley 20 inch Mach six tunnel. The investigation consisted of configuration buildup from the basic body by adding a wing, center vertical tail, three-module scramjet, and six-module scramjet engine. The test Mach number was six at a Reynolds number, based on model fuselage length, of about 13,700,000. The test angle-of-attack range was 4 to 20 D at constant angles of sideslip of 0, 2, and 4 deg. The elevons were deflected from 10 to -15 D for pitch control. Roll and yaw control were investigated. Experimental aerodynamic characteristics are compared with analytical elements.

Dillon, J. L.↗
DOE OSTI2025

Code Verification of Multiple Physics-Fidelity Models in Hypersonic Aerodynamics

Hypersonic aerodynamics models exist across a range of physics fidelities with associated computational expenses. These models may be run independently or in a multifidelity framework that leverages their complementary strengths of speed for lower-fidelity and accuracy for higher-fidelity models. This work presents applied code verification of two lower-fidelity models contained within the Sandia hypersonic aerodynamics code. Each model has a different form that requires individualized verification approaches, including comparison to analytical solutions as well as manufactured solutions with order-of-accuracy testing. In conclusion, results of this effort include the identification and resolution of code errors and shortcomings, as well as the demonstration of code correctness and consistency for both models.

Aerodynamics↗
NASA NTRS1996

Far term visions: The frontiers of the responsibly imaginable

This lecture discusses envisaged advanced concepts across the speed range including VTOL converticars (personal air transportation), advanced subsonic and supersonic long haul transports, hypersonic transports, and developments/applications of flow control technology. In most cases, these concepts and approaches offer at least the potential of 100 percent improvements in various performance metrics and, in some cases, far more. Special emphasis is given to advanced VTOL configurations which may offer simultaneous opportunities for mitigation of both drag-due-to-lift and wake vortex hazard and to synergistic propulsive and aerodynamic interactions. The lecture concludes that a virtual revolution in the civilian aeronautical world is conceivable as a result of technology maturation in several areas which could enable the exploitation of 'end-point' designs.

Bushnell, Dennis M.↗
NASA NTRS2008

Stereoscopic Imaging in Hypersonics Boundary Layers using Planar Laser-Induced Fluorescence

Stereoscopic time-resolved visualization of three-dimensional structures in a hypersonic flow has been performed for the first time. Nitric Oxide (NO) was seeded into hypersonic boundary layer flows that were designed to transition from laminar to turbulent. A thick laser sheet illuminated and excited the NO, causing spatially-varying fluorescence. Two cameras in a stereoscopic configuration were used to image the fluorescence. The images were processed in a computer visualization environment to provide stereoscopic image pairs. Two methods were used to display these image pairs: a cross-eyed viewing method which can be viewed by naked eyes, and red/blue anaglyphs, which require viewing through red/blue glasses. The images visualized three-dimensional information that would be lost if conventional planar laser-induced fluorescence imaging had been used. Two model configurations were studied in NASA Langley Research Center's 31-Inch Mach 10 Air Wind tunnel. One model was a 10 degree half-angle wedge containing a small protuberance to force the flow to transition. The other model was a 1/3-scale, truncated Hyper-X forebody model with blowing through a series of holes to force the boundary layer flow to transition to turbulence. In the former case, low flowrates of pure NO seeded and marked the boundary layer fluid. In the latter, a trace concentration of NO was seeded into the injected N2 gas. The three-dimensional visualizations have an effective time resolution of about 500 ns, which is fast enough to freeze this hypersonic flow. The 512x512 resolution of the resulting images is much higher than high-speed laser-sheet scanning systems with similar time response, which typically measure 10-20 planes.

Danehy, Paul M.↗
NASA NTRS2019

Effect of Out-Gassing on the Onset of Hypersonic Boundary Layer Transition

Prediction and control of the onset of transition and the associated variation in aerothermodynamic parameters in high-speed flows is key to optimize the performance and design of Thermal Protection Systems (TPS) of next-generation aerospace vehicles [1]. Boundary Layer Transition (BLT) characteristics can influence the surface heating budget determining the TPS thickness and consequently its weight penalty. Ablative heatshields are designed to alleviate the high heat flux at the surface through pyrolysis of their polymeric matrix and subsequent fiber ablation [2]. Pyrolysis leads to out-gassing and non-uniform ablation lead to surface roughness, both of which are known to influence the transition process. An ablator impacts BLT through three main routes: gas injecting into the boundary layer from the wall, changing the surface heat transfer due to wall-flow chemical reactions, and modifying surface roughness [3]. In preparation to Mars 2020 mission post-flight analysis, the predictive transition capability has been initiated toward hard-coupling porous material response analysis and aerothermal environment calculation.

Karimi, Mona↗
NASA NTRSDate not supplied

“Cold-Flow” Experiments Supporting CFD of Mixing Flowfields for High-Speed Fuel Injectors for Scramjet Applications

Recent flight demonstrations of supersonic combustion ramjet (scramjet) vehicles prove their increasing promise for military (rapid response and strike capability on global scale), aerospace (safer and more affordable access to space), and civil aviation (hypersonic point-to-point transport) applications. Currently, these technologies are still in their early development stages with commercial interest and investment at only a fraction of that of government organizations such as NASA and DoD. To advance hypersonic air-breathing propulsion technologies to the technology readiness levels necessary for access to space or widespread commercialization, further government investments and university engagement are needed over the next decade and likely beyond. This is because designing scramjet propulsion devices capable of robust high-speed air-breathing operation, characterized by rapid fuel and air mixing, short combustion times, and ensuring stable flame, has proven difficult. In this presentation, after a brief engineering-level introduction to scramjets technology, we will discuss one of the key challenges in high-speed propulsion design, namely the fuel injector design. Attempts at improving fuel injection to enhance fuel-air mixing while simultaneously reducing engine thrust losses have received a great deal of attention over the years. Although some amount of loss is thermodynamically unavoidable and occurs due to the desired effect of molecular mixing of fuel and air, any losses beyond this minimum required amount reduces the thrust potential of the engine. The Enhanced Injection and Mixing Project (EIMP) at NASA Langley Research Center aims at addressing this design challenge by analyzing the performance of a number of baseline and novel fuel injectors for high-speed applications. The project leverages computational and experimental capabilities with the goal to investigate scramjet fuel injection and mixing physics, improve our understanding of the underlying physical process, and develop enhancement strategies relevant to hypersonic flight Mach numbers. The talk will discuss the current computational and experimental research approaches using one of the baseline injectors considered by the EIMP as an example.

Scramjet↗
NASA NTRS1992

Control integration concept for hypersonic cruise-turn maneuvers

Piloting difficulties associated with conducting aircraft maneuvers in hypersonic flight are caused in part by the nonintuitive nature of the aircraft response and the stringent constraints anticipated on allowable angle of attack and dynamic pressure variations. An approach is documented that provides precise, coordinated maneuver control during excursions from a hypersonic cruise flight path and the necessary flight condition constraints. The approach is to achieve specified guidance commands by resolving altitude and cross range errors into a load factor and bank angle command by using a coordinate transformation that acts as an interface between outer and inner loop flight controls. This interface, referred to as a 'resolver', applies constraints on angle of attack and dynamic pressure perturbations while prioritizing altitude regulation over cross range. An unpiloted test simulation, in which the resolver was used to drive inner loop flight controls, produced time histories of responses to guidance commands and atmospheric disturbances at Mach numbers of 6, 10, 15, and 20. Angle of attack and throttle perturbation constraints, combined with high speed flight effects and the desire to maintain constant dynamic pressure, significantly impact the maneuver envelope for a hypersonic vehicle.

Raney, David L.↗
NASA NTRS1996

An Experimental Investigation of Wall-Cooling Effects on Hypersonic Boundary-Layer Stability in a Quiet Wind Tunnel

One of the primary reasons for developing quiet tunnels is for the investigation of high-speed boundary-layer stability and transition phenomena without the transition-promoting effects of acoustic radiation from tunnel walls. In this experiment, a flared-cone model under adiabatic- and cooled-wall conditions was placed in a calibrated, 'quiet' Mach 6 flow and the stability of the boundary layer was investigated using a prototype constant-voltage anemometer. The results were compared with linear-stability theory predictions and good agreement was found in the prediction of second-mode frequencies and growth. In addition, the same 'N=10' criterion used to predict boundary-layer transition in subsonic, transonic, and supersonic flows was found to be applicable for the hypersonic flow regime as well. Under cooled-wall conditions, a unique set of continuous spectra data was acquired that documents the linear, nonlinear, and breakdown regions associated with the transition of hypersonic flow under low-noise conditions.

Blanchard, Alan E.↗
NASA NTRS1991

Control concept for maneuvering in hypersonic flight

This research investigates an approach to provide precise, coordinated maneuver control during excursions from a hypersonic cruise flight path while observing the necessary flight condition constraints. The approach achieves specified guidance commands by resolving altitude and cross-range errors into a load factor and bank angle command through a coordinate transformation which acts as an interface between outer loop guidance controls and inner loop flight controls. This interface, referred to as a 'resolver', applies constraints on angle-of-attack and dynamic pressure perturbations while prioritizing altitude regulation over crossrange. An unpiloted test simulation, in which the resolver was used to drive inner-loop flight controls, produced time histories of responses to guidance commands at Mach numbers of 6, 10, 15, and 20. It is shown that angle-of-attack and throttle perturbation constraints, combined with high-speed flight effects and the desire to maintain constant dynamic pressure, significantly impact the maneuver envelope for a hypersonic vehicle. Turn rate, climb rate, and descent rate limits are expressed in terms of these constraints.

Raney, David L.↗
NASA NTRS1987

Acoustic fatigue: Overview of activities at NASA Langley

A number of aircraft and spacecraft configurations are being considered for future development. These include high-speed turboprop aircraft, advanced vertical take-off and landing fighter aircraft, and aerospace planes for hypersonic intercontinental cruise or flight to orbit and return. Review of the acoustic environment expected for these vehicles indicates levels high enough that acoustic fatigue must be considered. Unfortunately, the sonic fatique design technology used for current aircraft may not be adequate for these future vehicles. This has resulted in renewed emphasis on acoustic fatigue research at the NASA Langley Research Center. The overall objective of the Langley program is to develop methods and information for design of aerospace vehicles that will resist acoustic fatigue. The program includes definition of the acoustic loads acting on structures due to exhaust jets of boundary layers, and subsequent determination of the stresses within the structure due to these acoustic loads. Material fatigue associated with the high frequency structural stress reversal patterns resulting from acoustic loadings is considered to be an area requiring study, but no activity is currently underway.

Mixson, John S.↗
NASA NTRS1990

Advanced metallics for high temperature airframe structures

The development of new lower density materials with improved properties and higher use temperatures is considered essential enabling technology for nearly all envisioned aeronautics structural applications on the horizon. Notable examples of such applications include the High Speed Civil Transport (HSCT) in the supersonic regime and the National Aerospace Plane (NASP) in the hypersonic regime. This paper reviews the vehicle as well as material requirements for such applications and identifies candidate emerging metallics along with examples of reported properties. Finally, critical needs and current development status of candidate metallics are addressed.

Lisagor, W. Barry↗
NASA NTRS1996

Modeling of Inhomogeneous Compressible Turbulence Using a Two-Scale Statistical Theory

Turbulence modeling plays an important role in the study of high-speed flows in engineering and aerodynamic problems; they include flows in supersonic combustion engines and over hypersonic transport aircraft. The enhancement of the kinetic energy dissipation by the dilatational terms is one of the typical compressibility effects. Zeman (1990) and Sarkar et al. (1991) proposed that the dilatation dissipation is proportional to the solenoidal dissipation and is a function of the turbulent Mach number. Sarkar (1992) also modeled the pressure-dilatation correlation using the turbulent Mach number. Zeman (1991) related the correlation to the rate of change of the pressure variance.

Hamba, Fujihiro↗
NASA NTRS1992

Numerical simulations of high-speed flows about waveriders with sharp leading edges

A procedure is developed for the numerical simulation of stagnation-free inviscid supersonic and hypersonic flows about waveriders with sharp leading edges. The numerical approach involves the development of a specialized grid generator (named HYGRID), an algebraic solution-adaptive grid scheme, and a modified flow solving method. A comparison of the results obtained for several waverider geometries with exact solutions, other numerical solutions, and experimental results demonstrated the ability of the new procedure to produce stagnation-free Euler solutions about sharp-edged configurations and to describe the physics of the flow in these regions.

Jones, Kevin D.↗