Search NASA⌕ Search

SEARCH · Search NASA

Results for “High angle of attack”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1933

Effect of stabilizer location upon pitching and yawing moments in spins as shown by tests with the spinning balance

Tests were made with the spinning balance in a 5-foot wind tunnel to study the effect of stabilizer location upon the pitching and yawing moments given by the tail surfaces in spinning attitudes. The tests revealed that the horizontal surfaces, when in a normal location, seriously reduced the effectiveness of the fin and rudder, particularly at angles of attack of 50 degrees or more. The tests also revealed that a more forward or more rearward location gave no consistent or decided improvement; that a lower location greatly increased the shielding so that the yawing moment from the combination was in general less than that given by the bare fuselage; and that a higher location decreased the shielding and gave a favorable interference effect, particularly at the high angles of attack. Additional results regarding the stabilizer and the elevator are given.

Bamber, M J↗
NASA NTRS1978

Aerodynamic characteristics of a jet sheet vortex generator

A configuration concept for augmenting the lift capability of low aspect ratio, thin wings, typically used on fighter aircraft was investigated. The fluid strake concept uses a jet sheet formed by blowing from a series of small orifices located in the side of the fuselage ahead of the wing to generate a stable vortex flow over the wing at high angle of attack. The effect of the location of the fluid strake relative to the wing was investigated for three different designs of the in-line orifices using a half-span model tested in a 7 by 10 foot low speed tunnel. Based on the results of the low speed test, a jet sheet producing module was incorporated into a NASA general research fighter model and tested in the Langley 7 by 10 foot high speed tunnel to determine the effectiveness of the fluid strake as a lift-enhancement device in the high-speed maneuver regime. Tests were conducted over a Mach number range from 0.3 to 0.8, with a jet momentum coefficient range from 0 to 0.24. Significant lift increments resulted at the higher angles of attack and drag polars were improved.

Ziegler, H.↗
NASA NTRS1996

Design and Integration of an Actuated Nose Strake Control System

Aircraft flight characteristics at high angles of attack can be improved by controlling vortices shed from the nose. These characteristics have been investigated with the integration of the actuated nose strakes for enhanced rolling (ANSER) control system into the NASA F-18 High Alpha Research Vehicle. Several hardware and software systems were developed to enable performance of the research goals. A strake interface box was developed to perform actuator control and failure detection outside the flight control computer. A three-mode ANSER control law was developed and installed in the Research Flight Control System. The thrust-vectoring mode does not command the strakes. The strakes and thrust-vectoring mode uses a combination of thrust vectoring and strakes for lateral- directional control, and strake mode uses strakes only for lateral-directional control. The system was integrated and tested in the Dryden Flight Research Center (DFRC) simulation for testing before installation in the aircraft. Performance of the ANSER system was monitored in real time during the 89-flight ANSER flight test program in the DFRC Mission Control Center. One discrepancy resulted in a set of research data not being obtained. The experiment was otherwise considered a success with the majority of the research objectives being met.

Flick, Bradley C.↗
NASA NTRS1978

Reynolds number criticality in dynamic tests

To extrapolate from subscale wind tunnel tests to full-scale flight is a well-recognized problem. It becomes especially critical for present day high performance missiles and aircraft which operate at high angles of attack where separated flow effects often dominate the vehicle aerodynamics. The dynamic effects of flow separation can usually not be simulated at subscale Reynolds numbers. This is illustrated by examples of tests with slender vehicles and high performance aircraft. It is shown how analytic means can be developed establishing theoretical relationships between dynamic and static aerodynamic characteristics and how such means make it possible to extrapolate analytically from subscale tests to full-scale flight. The roll of future high Reynolds number facilities in establishing such 'analytic extrapolation' tools is discussed.

Ericsson, L. E.↗
NASA NTRS1992

Overview of high performance aircraft propulsion research

The overall scope of the NASA Lewis High Performance Aircraft Propulsion Research Program is presented. High performance fighter aircraft of interest include supersonic flights with such capabilities as short take off and vertical landing (STOVL) and/or high maneuverability. The NASA Lewis effort involving STOVL propulsion systems is focused primarily on component-level experimental and analytical research. The high-maneuverability portion of this effort, called the High Alpha Technology Program (HATP), is part of a cooperative program among NASA's Lewis, Langley, Ames, and Dryden facilities. The overall objective of the NASA Inlet Experiments portion of the HATP, which NASA Lewis leads, is to develop and enhance inlet technology that will ensure high performance and stability of the propulsion system during aircraft maneuvers at high angles of attack. To accomplish this objective, both wind-tunnel and flight experiments are used to obtain steady-state and dynamic data, and computational fluid dynamics (CFD) codes are used for analyses. This overview of the High Performance Aircraft Propulsion Research Program includes a sampling of the results obtained thus far and plans for the future.

Biesiadny, Thomas J.↗
NASA NTRS1992

Overview of high performance aircraft propulsion research

The overall scope of the NASA Lewis High Performance Aircraft Propulsion Research Program is presented. High performance fighter aircraft of interest include supersonic flights with such capabilities as short take off and vertical landing (STOVL) and/or high maneuverability. The NASA Lewis effort involving STOVL propulsion systems is focused primarily on component-level experimental and analytical research. The high-maneuverability portion of this effort, called the High Alpha Technology Program (HATP), is part of a cooperative program among NASA's Lewis, Langley, Ames, and Dryden facilities. The overall objective of the NASA Inlet Experiments portion of the HATP, which NASA Lewis leads, is to develop and enhance inlet technology that will ensure high performance and stability of the propulsion system during aircraft maneuvers at high angles of attack. To accomplish this objective, both wind-tunnel and flight experiments are used to obtain steady-state and dynamic data, and computational fluid dynamics (CFD) codes are used for analyses. This overview of the High Performance Aircraft Propulsion Research Program includes a sampling of the results obtained thus far and plans for the future.

Biesiadny, Thomas J.↗
NASA NTRS1984

Application of thin-layer Navier-Stokes equations near maximum lift

The flowfield about a NACA 0012 airfoil at a Mach number of 0.3 and Reynolds number of 1 million is computed through an angle of attack range, up to 18 deg, corresponding to conditions up to and beyond the maximum lift coefficient. Results obtained using the compressible thin-layer Navier-Stokes equations are presented as well as results from the compressible Euler equations with and without a viscous coupling procedure. The applicability of each code is assessed and many thin-layer Navier-Stokes benchmark solutions are obtained which can be used for comparison with other codes intended for use at high angles of attack. Reasonable agreement of the Navier-Stokes code with experiment and the viscous-inviscid interaction code is obtained at moderate angles of attack. An unsteady solution is obtained with the thin-layer Navier-Stokes code at the highest angle of attack considered. The maximum lift coefficient is overpredicted, however, in comparison to experimental data, which is attributed to the presence of a laminar separation bubble near the leading edge not modeled in the computations. Two comparisons with experimental data are also presented at a higher Mach number.

Anderson, W. K.↗
NASA NTRS1993

Aerodynamic control of NASP-type vehicles through vortex manipulation. Volume 3: Wing rock experiments

Free-to-roll tests were conducted in water and wind tunnels in an effort to investigate the mechanisms of wing rock on a NASP-type vehicle. The configuration tested consisted of a highly-slender forebody and a 78 deg swept delta wing. In the water tunnel test, extensive flow visualization was performed and roll angle histories were obtained. In the wind tunnel test, the roll angle, forces and moments, and limited forebody and wing surface pressures were measured during the wing rock motion. A limit cycle oscillation was observed for angles of attack between 22 deg and 30 deg. In general, the experiments confirmed that the main flow phenomena responsible for the wing-body-tail wing rock are the interactions between the forebody and the wing vortices. The variation of roll acceleration (determined from the second derivative of the roll angle time history) with roll angle clearly slowed the energy balance necessary to sustain the limit cycle oscillation. Different means of suppressing wing rock by controlling the forebody vortices using small blowing jets were also explored. Steady blowing was found to be capable of suppressing wing rock, but significant vortex asymmetrices are created, causing the model to stop at a non-zero roll angle. On the other hand, alternating pulsed blowing on the left and right sides of the fore body was demonstrated to be a potentially effective means of suppressing wing rock and eliminating large asymmetric moments at high angles of attack.

Suarez, Carlos J.↗
NASA NTRS1996

Control of Flow Separation Using Adaptive Airfoils

A novel way of controlling flow separation is reported. The approach involves using an adaptive airfoil geometry that changes its leading edge shape to adjust to the instantaneous flow at high angles of attack such that the flow over it remains attached. In particular, a baseline NACA 0012 airfoil, whose leading edge curvature could be changed dynamically by 400% was tested under quasi-steady compressible flow conditions. A mechanical drive system was used to produce a rounded leading edge to reduce the strong local flow acceleration around its nose and thus reduce the strong adverse pressure gradient that follows such a rapid acceleration. Tests in steady flow showed that at M = 0.3, the flow separated at about 14 deg. angle of attack for the NACA 0012 profile but could be kept attached up to an angle of about 18 deg by changing the nose curvature. No significant hysteresis effects were observed; the flow could be made to reattach from its separated state at high angles by changing the leading edge curvature. Interestingly, the flow over a nearly semicircular nosed airfoil was separated even at low angles.

Chandrasekhara, M. S.↗
NASA NTRS1996

Control of Flow Separation Using Adaptive Airfoils

A novel way of controlling flow separation is reported. The approach involves using an adaptive airfoil geometry that changes its leading edge shape to adjust to the instantaneous flow at high angles of attack such that the flow over it remains attached. In particular, a baseline NACA 0012 airfoil, whose leading edge curvature could be changed dynamically by 400% was tested under quasi-steady compressible flow conditions. A mechanical drive system was used to produce a rounded leading edge to reduce the strong local flow acceleration around its nose and thus reduce the strong adverse pressure gradient that follows such a rapid acceleration. Tests in steady flow showed that at M = 0.3, the flow separated at about 14 deg. angle of attack for the NACA 0012 profile but could be kept attached up to an angle of about 18 deg by changing the nose curvature. No significant hysteresis effects were observed; the flow could be made to reattach from its separated state at high angles by changing the leading edge curvature.

Chandrasekhara, M. S.↗
NASA NTRS2017

FLEET Velocimetry Measurements on a Transonic Airfoil

Femtosecond laser electronic excitation tagging (FLEET) velocimetry was used to study the flowfield around a symmetric, transonic airfoil in the NASA Langley 0.3-m TCT facility. A nominal Mach number of 0.85 was investigated with a total pressure of 125 kPa and total temperature of 280 K. Two-components of velocity were measured along vertical profiles at different locations above, below, and aft of the airfoil at angles of attack of 0 deg, 3.5 deg, and 7deg. Measurements were assessed for their accuracy, precision, dynamic range, spatial resolution, and overall measurement uncertainty in the context of the applied flowfield. Measurement precisions as low as 1 m/s were observed, while overall uncertainties ranged from 4 to 5 percent. Velocity profiles within the wake showed sufficient accuracy, precision, and sensitivity to resolve both the mean and fluctuating velocities and general flow physics such as shear layer growth. Evidence of flow separation is found at high angles of attack.

Burns, Ross A.↗
NASA NTRS1993

Symmetry breaking in vortical flows over cones - Theory and numerical experiments

A stability analysis suggests that inviscid incompressible flow, independent from angle of attack and regardless whether attached or separated, over slender cones is only marginally stable in regions of decelerating circumferential flow. Reducing slenderness or surface curvature lowers the energy level of harmonic perturbations, and, thus, reduces their impact on the overall stability of flows over slender cones. Associating the notion of instabilities in such flows with the onset of vortex asymmetries provides a model for explaining a variety of flow phenomena in Navier-Stokes simulations of laminar incompressible flows over three right circular cones at moderate to high angles of attack.

Hartwich, Peter M.↗
NASA NTRS1981

Curved-flow, rolling-flow, and oscillatory pure-yawing wind-tunnel test methods for determination of dynamic stability derivatives

Dynamic stability derivatives are evaluated on the basis of rolling-flow, curved-flow and snaking tests. Attention is given to the hardware associated with curved-flow, rolling-flow and oscillatory pure-yawing wind-tunnel tests. It is found that the snaking technique, when combined with linear- and forced-oscillation methods, yields an important method for evaluating beta derivatives for current configurations at high angles of attack. Since the rolling flow model is fixed during testing, forced oscillations may be imparted to the model, permitting the measurement of damping and cross-derivatives. These results, when coupled with basic rolling-flow or rotary-balance data, yield a highly accurate mathematical model for studies of incipient spin and spin entry.

Chambers, J. R.↗
NASA NTRS1994

Symmetry breaking in vortical flows over cones -- theory and numerical experiments

A stability analysis suggests that inviscid incompressible flow, independent from angle of attack and regardless whether attached or separated, over slender cones is only marginally stable in regions of decelerating circumferential flow. Reducing slenderness or surface curvature lowers the frequency spectrum of the harmonic perturbations and, thus, reduces their impact on the overall stability of flows over slender cones. Associating the notion of instabilities in such flows with the onset of vortex asymmetries provides a model for explaining a variety of flow phenomena in Navier-Stokes simulations of laminar incompressible flows over three right circular cones at moderate to high angles of attack.

Hartwich, Peter M.↗
NASA NTRS1984

Handling qualities related to stall/spin accidents of supersonic fighter aircraft

This paper reviews the handling qualities which influence the high angle of attack (AOA) behavior of supersonic fighter aircraft in order to obtain a clearer understanding of the causes of stall/spin accidents. The results show that, because modern fighters suffer more serious consequences when control is lost, good handling qualities are essential for safe operation at high AOA. Relaxed static stability used on some fighter aircraft can result in control problems at high AOA owing to inertia coupling and the difficulty of a recovery from a deep stall. Indications are that the use of departure/spin resistance and an automatic spin prevention system will greatly improve the safety record for modern supersonic fighters.

Anderson, S. B.↗
NASA NTRSDate not supplied

Comparison of Aerodynamic Analysis Tools Applied to a Propeller-Blown Wing

This paper describes initial results from an ongoing activity comparing two aerodynamic analysis tools: OVERFLOW, a Navier-Stokes flow solver, and FlightStream, a viscous surface-vorticity, unstructured panel method flow solver. Both tools are applied to analyses of an unblown wing and a propeller-blown wing, and then comparisons are performed between the predicted aerodynamic loads and moments from each tool. Computational performance and efficiencies of each tool and their usability in conceptual and preliminary air vehicle design are also discussed. A description of the workflow, underlying theoretical foundations, and best practices are provided. In comparing FlightStream and OVERFLOW, reasonable agreement between predicted performance is observed for flow regimes of interest at high angle of attack prior to stall, including blown wing aero-propulsive effects on lift augmentation and stall delay. In the post-stall regions, FlightStream appears to underestimate the effects of turbulent flow separation that contribute heavily to drag. However, as expected for a high-fidelity, time-accurate solver, the setup and computation time are substantially greater for OVERFLOW than for FlightStream.

Vivek Ahuja↗
NASA NTRSDate not supplied

Comparison of Aerodynamic Analysis Tools Applied to a Propeller-Blown Wing

This paper describes initial results from an ongoing activity comparing two aerodynamic analysis tools: OVERFLOW, a Navier-Stokes flow solver, and FlightStream, a viscous surface-vorticity, unstructured panel method flow solver. Both tools are applied to analyses of an unblown wing and a propeller-blown wing, and then comparisons are performed between the predicted aerodynamic loads and moments from each tool. Computational performance and efficiencies of each tool and their usability in conceptual and preliminary air vehicle design are also discussed. A description of the workflow, underlying theoretical foundations, and best practices are provided. In comparing FlightStream and OVERFLOW, reasonable agreement between predicted performance is observed for flow regimes of interest at high angle of attack prior to stall, including blown wing aero-propulsive effects on lift augmentation and stall delay. In the post-stall regions, FlightStream appears to underestimate the effects of turbulent flow separation that contribute heavily to drag. However, as expected for a high-fidelity, time-accurate solver, the setup and computation time are substantially greater for OVERFLOW than for FlightStream.

Vivek Ahuja↗
NASA NTRS1999

Additional Development and Systems Analyses of Pneumatic Technology for High Speed Civil Transport Aircraft

In the Task I portion of this NASA research grant, configuration development and experimental investigations have been conducted on a series of pneumatic high-lift and control surface devices applied to a generic High Speed Civil Transport (HSCT) model configuration to determine their potential for improved aerodynamic performance, plus stability and control of higher performance aircraft. These investigations were intended to optimize pneumatic lift and drag performance; provide adequate control and longitudinal stability; reduce separation flowfields at high angle of attack; increase takeoff/climbout lift-to-drag ratios; and reduce system complexity and weight. Experimental aerodynamic evaluations were performed on a semi-span HSCT generic model with improved fuselage fineness ratio and with interchangeable plain flaps, blown flaps, pneumatic Circulation Control Wing (CCW) high-lift configurations, plain and blown canards, a novel Circulation Control (CC) cylinder blown canard, and a clean cruise wing for reference. Conventional tail power was also investigated for longitudinal trim capability. Also evaluated was unsteady pulsed blowing of the wing high-lift system to determine if reduced pulsed mass flow rates and blowing requirements could be made to yield the same lift as that resulting from steady-state blowing. Depending on the pulsing frequency applied, reduced mass flow rates were indeed found able to provide lift augmentation at lesser blowing values than for the steady conditions. Significant improvements in the aerodynamic characteristics leading to improved performance and stability/control were identified, and the various components were compared to evaluate the pneumatic potential of each. Aerodynamic results were provided to the Georgia Tech Aerospace System Design Lab. to conduct the companion system analyses and feasibility study (Task 2) of theses concepts applied to an operational advanced HSCT aircraft. Results and conclusions from these experimental evaluations are presented herein, as are recommendations for further development and follow-on investigations. Also provided as an Appendix for reference are the basic results from the previous pneumatic HSCT investigations.

Englar, Robert J.↗