Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hydrogen Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Fuel-Cell Power Systems Incorporating Mg-Based H2 Generators

Two hydrogen generators based on reactions involving magnesium and steam have been proposed as means for generating the fuel (hydrogen gas) for such fuel-cell power systems as those to be used in the drive systems of advanced motor vehicles. The hydrogen generators would make it unnecessary to rely on any of the hydrogen storage systems developed thus far that are, variously, too expensive, too heavy, too bulky, and/or too unsafe to be practical. The two proposed hydrogen generators are denoted basic and advanced, respectively. In the basic hydrogen generator (see figure), steam at a temperature greater than or equals 330 C would be fed into a reactor charged with magnesium, wherein hydrogen would be released in the exothermic reaction Mg + H2O yields MgO + H2. The steam would be made in a flash boiler. To initiate the reaction, the boiler could be heated electrically by energy borrowed from a storage battery that would be recharged during normal operation of the associated fuel-cell subsystem. Once the reaction was underway, heat from the reaction would be fed to the boiler. If the boiler were made an integral part of the hydrogen-generator reactor vessel, then the problem of transfer of heat from the reactor to the boiler would be greatly simplified. A pump would be used to feed water from a storage tank to the boiler.

Kindler, Andrew↗

Preprototype nitrogen supply subsystem development

A nitrogen supply subsystem based on the dissociation of hydrazine into a mixture of hydrogen and nitrogen is developed. The latter is separated to provide makeup nitrogen to control the composition of spacecraft atmospheres. Specific hardware developments resulted in the design and fabrication of a nominal 3.6 kg/d nitrogen generation module. The design integrates a hydrazine catalytic dissociator, three ammonia dissociation stages and four hydrogen separation stages into a 33 kg, 14 cu dm module. A technique was devised to alternate the ammonia dissociation and hydrogen separation stages to give high nitrogen purity in the end product stream. Tests show the product stream to contain less than 0.5 percent hydrogen and 10 parts per million ammonia. The design and development of a test stand for the nitrogen generation module and a series of tests which verified its operation and performance capability are described.

Heppner, D. B.↗

Developing Science-based fueling protocols for 250-bar hydrogen tanks onboard hydrogen ferries: Experiments and modeling

Combined modeling and experimental studies are reported of the fueling of a large (28 kg capacity) 250-bar Type IV hydrogen tank of the type being deployed on early hydrogen ferries, such as the MV Sea Change. The primary goal was to determine how such tanks can be successfully fueled with hydrogen (state of charge greater than 97%) within 45 minutes without exceeding the 82 °C temperature limit for such tanks. The modeling studies show that a gas injector is needed to avoid thermal stratification during hydrogen fueling which can result in potential hot spots. Empirically, precooling of the hydrogen to 0 °C was found to be needed in some of the cases examined, as ambient conditions greatly affected the need for a precooling to achieve the 45-minute fill time desired by end users. The experimental results afforded a calibration of the engineering model SOFIL for these large 250-bar tanks, which now enables using SOFIL to predict volume-averaged hydrogen fueling temperatures to an accuracy of ±2.7°C for these tanks. The model can therefore be used to evaluate potential scenarios for development of a standardized fueling methodology for ferries utilizing large Type-IV tanks.

08 HYDROGEN↗

Demand and supply of hydrogen as chemical feedstock in USA

Projections are made for the demand and supply of hydrogen as chemical feedstock in USA. Industrial sectors considered are petroleum refining, ammonia synthesis, methanol production, isocyanate manufacture, edible oil processing, coal liquefaction, fuel cell electricity generation, and direct iron reduction. Presently, almost all the hydrogen required is produced by reforming of natural gas or petroleum fractions. Specific needs and emphases are recommended for future research and development to produce hydrogen from other sources to meet the requirements of these industrial sectors. The data and the recommendations summarized in this paper are based on the Workshop 'Supply and Demand of Hydrogen as Chemical Feedstock' held at the University of Houston on December 12-14, 1977.

Huang, C. J.↗

Chapter 7: Recent Advances in Electrocatalysts for Hydrogen Oxidation Reaction in Alkaline Electrolytes

The recent development in electrocatalysts for the hydrogen oxidation reaction (HOR) attracted significant attention. In this sense, this chapter provides a fundamental understanding of the state-of-the-art PGM and non-PGM-based electrocatalysts for the HOR in alkaline conditions. Moreover, a strong focus has been made on the strategies to overcome the slow kinetics of the HOR to commercialize anion-exchange membrane fuel cells.

anion-exchange membrane↗

Cost reductions in nickel-hydrogen battery

Significant progress was made toward the development of a commercially marketable hydrogen nickel oxide battery. The costs projected for this battery are remarkably low when one considers where the learning curve is for commercialization of this system. Further developmental efforts on this project are warranted as the H2/NiO battery is already cost competitive with other battery systems.

Beauchamp, Richard L.↗

Heating-Rate-Coupled Model for Hydrogen Reduction of JSC-1A

A previously developed and validated model for hydrogen reduction of JSC-1A for a constant reaction-bed temperature is extended to account for reaction during the bed heat-up period. A quasisteady approximation is used wherein an expression is derived for a single average temperature of reaction during the heat-up process by employing an Arrhenius expression for regolith conversion. Subsequently, the regolith conversion during the heat-up period is obtained by using this representative temperature. Accounting for the reaction during heat-up provides a better estimate of the reaction time needed at the desired regolith-bed operating temperature. Implications for the efficiency of the process, as measured by the energy required per unit mass of oxygen produced, are also indicated.

Hegde, U.↗

Final Report: Si and Na-SG Powder Hydrogen Fuel Cells

The primary project objective is to develop and demonstrate a controllable hydrogen generation system based on sodium silicide powder for portable fuel cell applications. This includes the development and demonstration of all balance of plant and reaction control components, which encompass water feeding, thermal management, and reaction site maximization. The appropriate manufacturing methods to readily scale production of sodium silicide will also be investigated.

08 HYDROGEN↗

Two‐Dimensional Polycyclic Photovoltaic Molecule with Low Trap Density for High‐Performance Photocatalytic Hydrogen Evolution

Abstract Typical organic semiconductors show a high trap density of states (10 16 –10 18 cm −3 ), providing a large number of centers for charge‐carrier recombination, thus hindering the development of photocatalytic hydrogen evolution. Here, we design and synthesize a two‐dimensional polycyclic photovoltaic material, named as TPP, to reduce the trap density to as low as 2.3×10 15 cm −3 , which is 1–3 orders of magnitude lower than those of typical organic semiconductors. Moreover, TPP exhibits a broad and strong absorption, ordered molecular packing with a large crystalline coherence length and enhanced electron mobility. Then, the bulk heterojunction nanoparticles (BHJ‐NPs) based on a blend of polymer donor (PM6) and TPP exhibit an average hydrogen evolution rate (HER) of 64.31 mmol h −1 g −1 under AM1.5G sunlight (100 mW cm −2 ), and 72.75 mmol h −1 g −1 under 330–1100 nm illumination (198 mW cm −2 ) higher than that of the control NPs based on typical PM6 : Y6 (62.67 mmol h −1 g −1 ).

Zhang, Zhenzhen↗

Two-Dimensional Polycyclic Photovoltaic Molecule with Low Trap Density for High-Performance Photocatalytic Hydrogen Evolution

Typical organic semiconductors show a high trap density of states (10 16 –10 18 cm -3 ), providing a large number of centers for charge-carrier recombination, thus hindering the development of photocatalytic hydrogen evolution. In this report we design and synthesize a two-dimensional polycyclic photovoltaic material, named as TPP, to reduce the trap density to as low as 2.3×10 15 cm -3 , which is 1–3 orders of magnitude lower than those of typical organic semiconductors. Moreover, TPP exhibits a broad and strong absorption, ordered molecular packing with a large crystalline coherence length and enhanced electron mobility. Then, the bulk heterojunction nanoparticles (BHJ-NPs) based on a blend of polymer donor (PM6) and TPP exhibit an average hydrogen evolution rate (HER) of 64.31 mmol h -1 g -1 under AM1.5G sunlight (100,mW cm -2 ), and 72.75 mmol h -1 g -1 under 330–1100 nm illumination (198 mW cm -2 ) higher than that of the control NPs based on typical PM6 : Y6 (62.67 mmol h -1 g -1 ).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Metal hydride hydrogen compression: Recent advances and future prospects

Metal hydride (MH) thermal sorption compression is one of the more important applications of the metal hydrides. The present paper reviews recent advances in the field based on the analysis of the fundamental principles of this technology. The performances when boosting hydrogen pressure, along with two- and three-step compression units are analyzed. The paper includes also a theoretical modeling of a two-stage compressor aimed at both describing the performance of the experimentally studied systems, but, also, on their optimization and design of more advanced MH compressors. Business developments in the field are reviewed for the Norwegian company HYSTORSYS AS and the South African Institute for Advanced Materials Chemistry. Finally, future prospects are outlined presenting the role of the metal hydride compression in the overall development of the hydrogen driven energy systems. Lastly, the work is based on the analysis of the development of the technology in Europe, USA and South Africa.

08 HYDROGEN↗

Silica-encapsulated Fe 2 O 3 oxygen carriers for selective chemical looping combustion of hydrogen

Methane dehydroaromatization (MDA) combined with chemical looping (CL) combustion of hydrogen can overcome the MDA thermodynamic constraints conventionally limiting conversion. Development of selective hydrogen-oxidation oxygen carriers in the presence of aromatics in the CL is key to improve MDA performance in the coupled reaction system. Here, in this paper, we show that a novel oxygen carrier (silica-encapsulated Fe 2 O 3 with Fe/Si mole ratio of 1.2) yields high overall methane conversion (49%) and aromatics yield (up to 36%) during 4 h of recirculating a stream in the developed system. A silica layer encapsulating Fe 2 O 3 favors hydrogen transport and oxidation, preventing aromatics diffusing to the Fe 2 O 3 surface. A close physical contact between iron oxide particles and silica, and near complete encapsulation of the particles by the silica layer can facilitate hydrogen conversion without full depletion of iron oxides by forming iron silicates. The silica-encapsulated iron oxide particles can be reoxidized in air after depletion of its oxidative capacity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Liquid-Hydrogen-Cooled 450-hp Electric Motor Test Stand Being Developed

With growing concerns about global warming, there is a need to develop pollution-free aircraft. One approach is to use hydrogen-fueled airc raft that use fuel cells or turbogenerators to produce electric power to drive the electric motors that turn the aircraft#s propulsive fan s. Hydrogen fuel would be carried as a liquid, stored at its boiling point of 20.5 K (-422.5 ?F). Conventional electric motors, however, are too heavy to use on an aircraft. We need to develop high-power, lig htweight electric motors (high-powerdensity motors).

Kascak, Albert F.↗

One Step Hydrogen Generation Through Sorption Enhanced Reforming

One-step hydrogen generation, using Sorption Enhanced Reforming (SER) technology, is an innovative means of providing critical energy and environmental improvements to US manufacturing processes. The Gas Technology Institute (GTI) is developing a Compact Hydrogen Generator (CHG) process, based on SER technology, which successfully integrates previously independent process steps, achieves superior energy efficiency by lowering reaction temperatures, and provides pathways to doubling energy productivity with less environmental pollution. GTI’s prior CHG process development efforts have culminated in an operational pilot plant. During the initial pilot testing, GTI identified two operating risks- 1) catalyst coating with calcium aluminate compounds, 2) limited solids handling of the sorbent. Under this contract GTI evaluated alternative materials (one catalyst and two sorbents) to mitigate both risks. The alternate catalyst met performance targets and did not experience coating with calcium aluminate compounds of any kind. The alternate sorbent materials demonstrated viable operation, with one material enabling a three-fold increase in sorbent flow. The testing also demonstrated operation at 90% of its rated capacity. Lastly, a carbon dioxide co-production study was performed to assess the advantage of the solid phase separation of carbon dioxide- inherent in the CHG process. Approximately 70% lower capital cost is achievable compared to SMR-based hydrogen production with CO2 capture, as well as improved operating costs.

08 HYDROGEN↗

Operando X-Ray Diffraction During High Temperature Electrolysis

This work presents the design, development, and deployment of an operando X-ray diffraction (XRD) system for high-temperature electrolysis (HTE), enabling real-time characterization of solid oxide electrolysis cells (SOECs) under true operational conditions. The integration of an HTE test stand within a synchrotron radiation environment, mimicking the conditions of a laboratory setup, aims to enhance our understanding of the degradation processes affecting the performance and longevity of SOECs. Utilizing a custom furnace and a high precision motor stack assembly at the Stanford Synchrotron Radiation Lightsource (SSRL), the system revealed unparalleled insights into the structural evolution of SOEC components through various operational stages, including initial heat ramp, cell reduction, fuel ramp, and wet electrolysis. Initial results demonstrate the significant impact of the initial heating and cooling on secondary phase formation within the SOEC, highlighting the utility of operando XRD for developing more efficient and durable hydrogen production technologies.

08 HYDROGEN↗

A High-Rate Lithium Manganese Oxide-Hydrogen Battery

Rechargeable hydrogen gas batteries show promises for the integration of renewable yet intermittent solar and wind electricity into the grid energy storage. Here, we describe a rechargeable, high-rate, and long-life hydrogen gas battery that exploits a nanostructured lithium manganese oxide cathode and a hydrogen gas anode in an aqueous electrolyte. The proposed lithium manganese oxide-hydrogen battery shows a discharge potential of ~1.3 V, a remarkable rate of 50 C with Coulombic efficiency of ~99.8%, and a robust cycle life. A systematic electrochemical study demonstrates the significance of the electrocatalytic hydrogen gas anode and reveals the charge storage mechanism of the lithium manganese oxide-hydrogen battery. This work provides opportunities for the development of new rechargeable hydrogen batteries for the future grid-scale energy storage.

25 ENERGY STORAGE↗

Final Report: Hydrogen Production Pathways Cost Analysis (2013 – 2016)

This report summarizes work conducted under a three year Department of Energy (DOE) funded project to Strategic Analysis, Inc. (SA) to analyze multiple hydrogen (H 2 ) production technologies and project their corresponding levelized production cost of H 2 . The analysis was conducted using the H2A Hydrogen Analysis Tool developed by the DOE and National Renewable Energy Laboratory (NREL). The project was led by SA but conducted in close collaboration with the NREL and Argonne National Laboratory (ANL). In-depth techno-economic analysis (TEA) of five different H 2 production methods was conducted. These TEAs developed projections for capital costs, fuel/feedstock usage, energy usage, indirect capital costs, land usage, labor requirements, and other parameters, for each H 2 production pathway, and use the resulting cost and system parameters as inputs into the H2A discounted cash flow model to project the production cost of H 2 ($/kgH 2 ). Five technologies were analyzed as part of the project and are summarized in this report: Proton Exchange Membrane technology (PEM), High temperature solid oxide electrolysis cell technology (SOEC), Dark fermentation of biomass for H 2 production, H 2 production via Monolithic Piston-Type Reactors with rapid swing reforming and regeneration reactions, and Reformer-Electrolyzer-Purifier (REP) technology developed by Fuel Cell Energy, Inc. (FCE).

08 HYDROGEN↗

Optical Fiber H2 Sensor Operating in Harsh Environments of Subsurface H2 Storage Reservoirs

Monitoring hydrogen concentration in the subsurface storage reservoirs is vital to ensure the integrity and safety of the storage facilities. An optical fiber hydrogen sensor consisting of a palladium-based sensing layer and a protective polymer layer was developed and evaluated in simulated subsurface hydrogen storage conditions. The developed optical fiber hydrogen sensor has demonstrated successful sensing performance at ~80 °C, ~1,000 psi, and ~100% RH. In addition, the sensor was exposed to real subsurface microbial samples in the harsh environments to monitor microbially induced changes in hydrogen concentration. The sensor has shown stable H2 sensing responses in the replicated underground hydrogen storage conditions without deterioration or loss of H2 sensitivity in the presence of biological samples.

filter layer↗