Search NASA⌕ Search

SEARCH · Search NASA

Results for “Model Checking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Viking 1975 orbiter development test model/Lander dynamic test model, dynamic environmental testing

A series of dynamic environmental tests on the Viking 1975 Orbiter/Lander model provided information regarding damping and linearity. The quality of mode isolation was made with orthogonality checks. A pretest criterion established for orthogonality provided good correlation with test results. Part of the post-test analysis was dedicated to a review of instrumentation selection for control and/or response limiting. Limited load values were also examined.

Milder, G.↗

Trace element geochemistry and the early lunar differentiation

The results are considered of experiments in which thermal neutron activation analysis was used to measure the halogens, U, Te, Ru, Os, and Hg in lunar samples. A calorimetric method was used for P2O5. Three Apollo 17 basalts, one Apollo 11 basalt, and one Apollo 15 basalt were used for the Ru-Os study. Os and Ru were measured in seven samples of breccia 14305 in a series of experiments to check an apparent anomaly in the isotopic composition of the Hg which it contains. A lunar model for Ru-Os partition is discussed. It is suggested that Ru and Os were partitioned and fractionated in the original differentiation of the lunar surface ocean. Fractionation among near-surface materials was less than a factor of 2 according to the lithic breccia data. Fractionations among basaltic sources were very large, exceeding 100, and primarily due to Ru. A clue to Ru and Os distributions at the depths from which mare basalts were derived may be provided by the relative ages of the basalts. These are interpreted as being related to partial melting in response to temperature increases at depth with time.

Jovanovic, S.↗

Vertical extensions of galactic spiral arms

The vertical structure of the large scale galactic shock along spiral arms is studied in order to understand the extended features or the wings of spiral arms observed by Kepner (1970) and recently checked by Soukup (1979). Numerical calculations of two-dimensional gas flow were performed for two models of the gas. The results show that the shock front, standing perfectly perpendicular to the galactic plane, extends impressively above the scale height of the interstellar gas. In the extreme case of isothermal gas, the shock solution exists at any distance from the plane. In a realistic model in which the kinetic temperature of the gas is stratified, increasing with height, the shock can extend up to 700 pc. For both models, although the velocity component perpendicular to the galactic plane is small, the solutions corresponding to layered one-dimensional flow contain no shocks at such heights. In order to study the geometry of the shock front and the flow pattern near it, a simplified model is adopted, in which the Coriolis force is neglected. However, estimates show that including it will enhance the shock strength. The compression at the shock front makes the gas observable at high latitudes.

Soukup, J. E.↗

Two-dimensional numerical simulation of a Stirling engine heat exchanger

The first phase of an effort to develop multidimensional models of Stirling engine components is described. The ultimate goal is to model an entire engine working space. Parallel plate and tubular heat exchanger models are described, with emphasis on the central part of the channel (i.e., ignoring hydrodynamic and thermal end effects). The model assumes laminar, incompressible flow with constant thermophysical properties. In addition, a constant axial temperature gradient is imposed. The governing equations describing the model have been solved using the Crack-Nicloson finite-difference scheme. Model predictions are compared with analytical solutions for oscillating/reversing flow and heat transfer in order to check numerical accuracy. Excellent agreement is obtained for flow both in circular tubes and between parallel plates. The computational heat transfer results are in good agreement with the analytical heat transfer results for parallel plates.

Ibrahim, Mounir↗

Measurement of Force Balance Repeatability and Reproducibility in the NTF

A recently published statistical approach for measuring and evaluating wind tunnel force balance repeatability and reproducibility is applied to three check standard tests in the National Transonic Facility at NASA Langley Research Center. Two different airframe models and force balances were used. The short-term repeatability and within-test reproducibility are separately estimated and correlations with tunnel parameters are carried out. Conjectures are presented for the development of scaling laws for predicting the repeatability and reproducibility of other force balance tests in the tunnel.

Hemsch, M. J.↗

HDU Pressurized Excursion Module (PEM) Prototype Systems Integration

The Habitat Demonstration Unit (HDU) project team constructed an analog prototype lunar surface laboratory called the Pressurized Excursion Module (PEM). The prototype unit subsystems were integrated in a short amount of time, utilizing a skunk-works approach that brought together over 20 habitation-related technologies from a variety of NASA centers. This paper describes the system integration strategies and lessons learned, that allowed the PEM to be brought from paper design to working field prototype using a multi-center team. The system integration process included establishment of design standards, negotiation of interfaces between subsystems, and scheduling fit checks and installation activities. A major tool used in integration was a coordinated effort to accurately model all the subsystems using CAD, so that conflicts were identified before physical components came together. Some of the major conclusions showed that up-front modularity that emerged as an artifact of construction, such as the eight 45 degree "pie slices" making up the module whose steel rib edges defined structural mounting and loading points, dictated much of the configurational interfaces between the major subsystems and workstations. Therefore, 'one of the lessons learned included the need to use modularity as a tool for organization in advance, and to work harder to prevent non-critical aspects of the platform from dictating the modularity that may eventually inform the fight system.

Gill, Tracy R.↗

MESA: Scalable Runtime Verification Tool Using Actors

This work presents our runtime verification approach implemented by the tool MESA (MEssage-based System Analysis) which allows for using concurrent monitors to check for properties specified in linear temporal logic and finite state machines.We employ the actor programing model to implement MESA where monitors are captured by concurrent actors that communicate via messaging. The paper also presents a case study where MESA is used to monitor flights in National Airspace System of United States using live air traffic data stream. The case study which motivated this work in the first place shows that our approach is effective.We also perform empirical study by conducting experiments using monitoring systems with different numbers of concurrent monitors and different layers of indexing.This paper describes our experiments, evaluates our results,and discusses challenges faced during the study. The evaluation shows our approach is scalable.

runtime verification, concurrency, actor programin↗

Recommendations on Evidence and Process for Certification of Learning-enabled Components in Aerospace Systems

This report primarily identifies a collection of relevant and necessary evidence for assurance of machine learnt components (MLCs)—also known as learning-enabled components—integrated into aircraft systems, and gives preliminary suggestions on the elements of a certification process that invoke the identified evidence. The main focus is on feedforward neural networks that are static and trained offline through supervised learning. A brief background on the generic elements of the lifecycle of an MLC is given to contextualize the assurance considerations and, consequently, the evidence that is relevant and necessary to support certification. At the level of an MLC, those considerations relate to: (i) the consistency and correctness of MLC contributions to system functions in the context of a validated functional intent; and (ii) the absence of MLC contributions to aircraft-level failure conditions. At an ML model level, confidence in model and data properties contribute to assurance of the containing MLC, in particular: (a) generalizability and robustness of models, in the presence of inputs not previously seen during training, disturbances to inputs, and unexpected inputs; and (b) valid data, i.e., data that are at least representative, relevant, complete, and accurate. Evidence for the above span the elements of the ML lifecycle, and includes, at a minimum, lifecycle artifacts that pertain to: (1) properties of requirements capturing functional intent, safety constraints, and aspects of the intended use and operating environment; (2) model performance, model complexity and design, and algorithm choice; (3) achievement of required performance at the levels of a trained model during model development, a trained model after model development is complete, and a trained model that is transformed into an executable equivalent; (4) model implementation aspects necessary for transforming a trained model into the executable equivalent; (5) integration of the executable trained model into the containing MLC, and eventually the larger system; and, (6) lastly, the verification and validation (V&V) of each of the above. Such V&V lifecycle artifacts themselves include: aspects of coverage, e.g., of various levels of requirements by the input space of the model and the data; traceability (where applicable); application of formal methods for property specification, analysis, and checking. Examples of evidence generation methods and tools further ground the discussion on what constitutes evidence, and the contribution to assurance during certification. The identified assurance considerations and supporting evidence is not a comprehensive set. Additionally, neither what should be considered as sufficient evidence relative to the assigned criticality of an MLC, nor how criticality ought to be determined and adjusted, have been considered in this report. However, suggestions are made for potential activities of the ML lifecycle that are aimed at providing confidence that an MLC can be relied upon when integrated into its containing (aircraft) system. Those activities are proposed as candidate elements of a certification process for MLCs. The main purpose of this report to inform regulatory guidance and consensus standards that may be used to meet the safety intent of the applicable regulations.

Aviation safety↗

Ames Research Center Mars/Pathfinder Heat Shield Design Verification ARC-JET Test

Design verification tests were performed on samples representing the aerobrake of the Mars/Pathfinder vehicle. The test specimens consisted of the SLA-561V ablator bonded to the honeycomb structure. The primary objective was to evaluate the ablation materials performance and to measure temperatures within the ablator, at the structural bondline and at the back sheet of the honeycomb structure. Other objectives were to evaluate the effect of ablative repair plug material treatment and voids in the heat shield. A total of 29 models were provided for testing in the Ames 60MW arc-jet facility. Of these, 23 models were flat-faced and six remaining models were curved edge ones, intended to simulate the conditions on the curved rim of the forebody where the maximum shear occurred. Eight sets of test conditions were used. The stagnation point heating rates varied from 47 to 240 W/cm2 and the stagnation pressures from 0.15 to 0.27 atm. (The maximum flight values are 132 W/cm2 and 0.25 atm) The majority of these runs were made at a nominal stagnation pressure of 0.25 atm. Two higher pressure runs were made to check the current (denser) ablation material for spallation, or other forms of thermal stress failure. Over 60% of the flatfaced models yielded good thermocouple data and all produced useful surface recession information. Of the five curved-edge models that were tested, only one gave good data; the remaining ones experienced model-holder failure. The test results can be summarized by noting that no failure of the ablative material was observed on any model. Also, the bondline temperature design limit of 250 C was never reached within an equivalent flight time despite a stagnation point heat load that exceeded the maximum flight value by up to 130%. At heating rates of over 200W/cm2 and stagnation pressures of 0.25 atm, or greater, the average surface recessions exceeded 0.5 cm on some models. The surface roughness increased dramatically at pressures above 0.25 atm and was four times greater at 0.27 atm than at 0.25 atm. Procured repair plug material performed much better than room-temperature cured plugs, as observed in the previous tests. Voids in the ablator did not increase local temperatures and gaps did not grow during testing.

Tran, Huy K.↗

Model-Based Fault Diagnosis for Turboshaft Engines

Tests are described which, when used to augment the existing periodic maintenance and pre-flight checks of T700 engines, can greatly improve the chances of uncovering a problem compared to the current practice. These test signals can be used to expose and differentiate between faults in various components by comparing the responses of particular engine variables to the expected. The responses can be processed on-line in a variety of ways which have been shown to reveal and identify faults. The combination of specific test signals and on-line processing methods provides an ad hoc approach to the isolation of faults which might not otherwise be detected during pre-flight checkout.

Green, Michael D.↗

A Categorization of Dynamic Analyzers

Program analysis techniques and tools are essential to the development process because of the support they provide in detecting errors and deficiencies at different phases of development. The types of information rendered through analysis includes the following: statistical measurements of code, type checks, dataflow analysis, consistency checks, test data,verification of code, and debugging information. Analyzers can be broken into two major categories: dynamic and static. Static analyzers examine programs with respect to syntax errors and structural properties., This includes gathering statistical information on program content, such as the number of lines of executable code, source lines. and cyclomatic complexity. In addition, static analyzers provide the ability to check for the consistency of programs with respect to variables. Dynamic analyzers in contrast are dependent on input and the execution of a program providing the ability to find errors that cannot be detected through the use of static analysis alone. Dynamic analysis provides information on the behavior of a program rather than on the syntax. Both types of analysis detect errors in a program, but dynamic analyzers accomplish this through run-time behavior. This paper focuses on the following broad classification of dynamic analyzers: 1) Metrics; 2) Models; and 3) Monitors. Metrics are those analyzers that provide measurement. The next category, models, captures those analyzers that present the state of the program to the user at specified points in time. The last category, monitors, checks specified code based on some criteria. The paper discusses each classification and the techniques that are included under them. In addition, the role of each technique in the software life cycle is discussed. Familiarization with the tools that measure, model and monitor programs provides a framework for understanding the program's dynamic behavior from different, perspectives through analysis of the input/output data.

Lujan, Michelle R.↗

Flight Rule Design, Implementation, Verification, and Validation for the Psyche Mission

NASA Jet Propulsion Lab (JPL)’s upcoming mission Psyche will begin its journey to the asteroid (16) Psyche in late 2022 in an effort to better understand its origins and, in turn, better understand our own. Operating the spacecraft safely will require the dedicated efforts of a small team that understands the spacecraft’s operational constraints, as well as a set of powerful spacecraft models designed to catch command errors that can pose risks to mission success. One of the responsibilities of the operations team is to ensure adherence to a set of Flight Rules written by spacecraft and instrument experts that are designed to mitigate these risks. Psyche’s innovations in Flight Rule design principles and advancements in the tools and processes used to implement and check Flight Rules are discussed. A comparison of Psyche’s approach to Flight Rules to other JPL missions will provide lessons learned for future missions that must perform constraint checking during operations. Flight Rule development faces several major challenges. First, flight rule developers must work with Subject Matter Experts (SME) to write the rules in a way that captures the intent of the constraint in a straightforward, enforceable manner. Second, software implementers must correctly interpret flight rules into code so that it meets the original intent of the SME. Finally, a means must be provided for SMEs to validate flight rule implementations without requiring them to understand the underlying software. Innovative processes intended to efficiently close the loop between stakeholders and software developers are described, such as the use of test-driven development to provide stakeholders with easy-to-review implementations. New guidelines for flight rule writing, designed to address these challenges, are described for future missions to adopt and build upon. Psyche Mission System has a variety of new and heritage tools that improve in the Flight Rule validation and checking process. Psyche developed a powerful, new tool called RandSEQ and made significant improvements to Octopusjam, two valuable tools that aid the development of Flight Rule unit tests. Advancements in the models and processes for performing sequence validation with SEQuence GENerator (SEQGEN), the primary, high-heritage tool used for automated flight rule checks on Psyche, are described. The development of new software and the advancements to existing software put Psyche at the forefront of Flight Rule technology. All missions must perform detailed constraint checking, so a comparison of Psyche’s approach to some of these items to the approaches taken by other missions such as Dawn, M2020, and Europa Clipper is done, specifically to examine SME-developer communication, tools used, and development process. Lessons learned from this comparison will be provided.

Weise, Tim↗

Theory of wing-body drag at supersonic speeds

The relation of Whitcomb's area rule to the linear formulas for wave drag at slightly supersonic speeds is discussed. By adopting an approximate relation between the source strength and the geometry of a wing-body combination, the wave drag theory is expressed in terms involving the areas intercepted by oblique planes or Mach planes. The resulting formulas are checked by comparison with the drag measurements obtained in wind tunnel experiments and in experiments with falling models in free air. Finally, a theory for determining wing-body shapes of minimum drag at supersonic Mach numbers is discussed and some preliminary experiments are reported.

Jones, R. T.↗

Uniformity of Ludwieg tube flows

Pressure and speed of sound measurements are used to obtain averaged gas properties in a Ludwieg combustion tube in which the gas is burned just prior to use. Absorption of a laser beam in the exit flow is used to check the predicted temperature uniformity. The burning process and the heat transfer to the cold walls are modeled. Interferograms of Ludwieg tube boundary layers are utilized to develop a new semiempirical boundary layer expression referred to as the integral density thickness, which is then applied to a recently developed linearized analysis of the effects of this layer. Pressure-time histories are determined for a wide range of tube flow Mach number and aspect ratio. Viscous and nonviscous effects are considered. It is shown that although the influence of the integral density thickness on the flow can be large, a modified linear theory can be used to estimate the effects for arbitrary tube flow Mach number and values of the aspect ratio that include cases where the boundary layers have merged.

Russell, D. A.↗

FAME, a microprocessor based front-end analysis and modeling environment

Higher order software (HOS) is a methodology for the specification and verification of large scale, complex, real time systems. The HOS methodology was implemented as FAME (front end analysis and modeling environment), a microprocessor based system for interactively developing, analyzing, and displaying system models in a low cost user-friendly environment. The nature of the model is such that when completed it can be the basis for projection to a variety of forms such as structured design diagrams, Petri-nets, data flow diagrams, and PSL/PSA source code. The user's interface with the analyzer is easily recognized by any current user of a structured modeling approach; therefore extensive training is unnecessary. Furthermore, when all the system capabilities are used one can check on proper usage of data types, functions, and control structures thereby adding a new dimension to the design process that will lead to better and more easily verified software designs.

Rosenbaum, J. D.↗

Computation of Jupiter interior models from gravitational inversion theory

Spacecraft measurements of Jupiter have provided the mass, standard pressure level radius, rotation law, internal mass distribution multipole moments, and internal composition and temperature distribution constraints, for the present implementation of a method for deriving planetary interior models that exactly satisfy a set of N gravitational constraints by means of appropriate iteration. The models are not forced to fit the more indirectly derived constraints, which are instead used as conistency checks. In the case of an He mass fraction in the envelope Y of 0.2, the inferred pressure at a mass density of about 0.2 g/cu cm is about a factor of 2 higher than would be indicated by experimental H compression data in the relevant pressure range of 100,000 to one million bar. The inferred pressure distribution is in better agreement with the shock data for a nominal Y value of 0.3 + or - 0.05.

Hubbard, W. B.↗

The NASA Lewis integrated propulsion and flight control simulator

A new flight simulation facility was developed at NASA-Lewis. The purpose of this flight simulator is to allow integrated propulsion control and flight control algorithm development and evaluation in real time. As a preliminary check of the simulator facility capabilities and correct integration of its components, the control design and physics models for a short take-off and vertical landing fighter aircraft model were shown, with their associated system integration and architecture, pilot vehicle interfaces, and display symbology. The initial testing and evaluation results show that this fixed based flight simulator can provide real time feedback and display of both airframe and propulsion variables for validation of integrated flight and propulsion control systems. Additionally, through the use of this flight simulator, various control design methodologies and cockpit mechanizations can be tested and evaluated in a real time environment.

Bright, Michelle M.↗

The NASA Lewis integrated propulsion and flight control simulator

A new flight simulation facility has been developed at NASA Lewis to allow integrated propulsion-control and flight-control algorithm development and evaluation in real time. As a preliminary check of the simulator facility and the correct integration of its components, the control design and physics models for an STOVL fighter aircraft model have been demonstrated, with their associated system integration and architecture, pilot vehicle interfaces, and display symbology. The results show that this fixed-based flight simulator can provide real-time feedback and display of both airframe and propulsion variables for validation of integrated systems and testing of control design methodologies and cockpit mechanizations.

Bright, Michelle M.↗