Search NASA⌕ Search

SEARCH · Search NASA

Results for “PHASE MODULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Feasibility study on 8PSK, QPSK, TFM, by using CLASS for Space Station/TDRSS real measured channel

The feasibility of transmitting 500 Mbps data rate through the TDRSS real channel (about 2.5 bits/sec/Hz) for the Space Station application is studied in this paper. The modulation schemes examined are octal phase shift keying, quarternary phase shift keying, and tamed frequency modulation scheme. The software tool used is the Communication Link Analysis and Simulation System. A channel equalizer is shown to be required for such application. Sensitivity results, eye diagrams, and phase trajectory diagrams are presented for discussions.

An, Song H.↗
NASA NTRS1975

Development of components for an S-band phased array antenna subsystem

The system requirements, module test data, and S-band phased array subsystem test data are discussed. Of the two approaches to achieving antenna gain (mechanically steered reflector or electronically steered phased array), the phased array approach offers the greatest simplicity and lowest cost (size, weight, power, and dollars) for this medium gain. A competitive system design is described as well as hardware evaluation which will lead to timely availability of this technology for implementing such a system. The objectives of the study were: to fabricate and test six engineering model transmit/receive microelectronics modules; to design, fabricate, and test one dc and logic multilayer manifold; and to integrate and test an S-band phased array antenna subsystem composed of antenna elements, seven T/R modules, RF manifolds and dc manifold.

Source record↗
NASA NTRS1991

Resolving Phase Ambiguities In OQPSK

Improved design for modulator and demodulator in offset-quaternary-phase-key-shifting (OQPSK) communication system enables receiver to resolve ambiguity in estimated phase of received signal. Features include unique-code-word modulation and detection and digital implementation of Costas loop in carrier-recovery subsystem. Enchances performance of carrier-recovery subsystem, reduces complexity of receiver by removing redundant circuits from previous design, and eliminates dependence of timing in receiver upon parallel-to-serial-conversion clock.

Nguyen, Tien M.↗
NASA NTRS1988

ART/Ada design project, phase 1. Task 3 report: Test plan

The plan is described for the integrated testing and benchmark of Phase Ada based ESBT Design Research Project. The integration testing is divided into two phases: (1) the modules that do not rely on the Ada code generated by the Ada Generator are tested before the Ada Generator is implemented; and (2) all modules are integrated and tested with the Ada code generated by the Ada Generator. Its performance and size as well as its functionality is verified in this phase. The target platform is a DEC Ada compiler on VAX mini-computers and VAX stations running the VMS operating system.

Allen, Bradley P.↗
NASA NTRS1990

Improved DMD configurations for image correlation

Two novel deformable mirror structures have been developed for spatial light modulators: an 'AM torsion beam' and a 'phase-mostly single-quadrant cantilever' beam. Both devices are well-suited to optical correlator input and filtering functions. Which the optical modulation characteristic of the torsion-beam modulator is essential amplitude only, which is well suited for use as the input modulator of the optical correlator, the characteristic of the one-quadrant modulator is a phase-mostly modulation whose amplitude changes are coupled to the phase changes; this renders it operable in the Fourier plane of the optical correlator as the filtering device.

Florence, James M.↗
NASA NTRS1975

A dynamic model for the time evolution of the modulated cosmic ray spectrum

A recently developed model predicts an energy dependent phase lag in the modulated cosmic ray density U(t) given by U(t) approximately equal to US (t - tau) where US is the solution to the Fokker-Planck equation under time independent conditions and tau is the average time spent by particles inside the modulating region. The delay times tau are functions of modulating parameters R (the radius of the modulating cavity), V (the solar wind velocity), and K (the effective average diffusion-coefficient which is a function of energy). This model is applied to predict the time evolution of the modulated cosmic ray proton spectrum over a simulated solar cycle. A modulation produced mostly by varying R over the solar cycle is less consistent with the observations.

Ogallagher, J. J.↗
NASA NTRS1976

Development and evaluation of a set of group delay standards

A set of cable assemblies serving as group delay standards having nominal delays of 15, 30, and 60 nsec are described. Various types of measurements were performed on the cable standards, including impedance, microwave phase shift, RF pulse burst delay, modulation pulsed delay, and envelope phase shift measurements. The results of these tests are given, and various sources of error are discussed, in particular, dispersion and internal reflections.

Otoshi, T. Y.↗
NASA NTRS1985

Changes in radial gradients of low-energy cosmic rays between solar minimum and maximum: - Observations from 1 to 31 AU

Observations of the fluxes and radial gradients of protons and helium (with energies of 10-70 Mev per n) between the period of minimum solar modulation ending in 1977 and the period of maximum modulation in 1981-1983 show that, over the radial range 1-31 AU, radial gradients decreased for both species from their solar minimum values (5-10 percent per AU for galactic protons and helium) to values of 2-4 percent per AU or less. For these low-energy cosmic rays it is found that the variation in modulation with the phase of the solar cycle is much stronger at radii of 20-30 AU than at 1 AU, and that at solar maximum, more than 99 percent of the total modulation takes place beyond 31 AU.

Mckibben, R. B.↗
NASA NTRS1994

ROSAT observations of the Jupiter aurora

Roentgen satellite (ROSAT) high-resolution imager (HRI) and position sensitive proportional counter (PSPC) observations of Jupiter obtained in April 1991 and May 1992 reveal soft X-ray emissions apparently associated with Jupiter's aurora and similar to X-ray emssions observed earlier by the Einstein Observatory. The HRI images show emission mainly from Jupiter's northern hemisphere at all Jovian longitudes observed, and there is some indication of a longitudinal modulation of the emission in phase with well-known ultraviolet modulation of the northern aurora. The PSPC data reveal a very soft spectrum. Comparison of the observed spectrum with models for both electron bremsstrahlung radiation and line emission from S and O ions indicates that the line spectrum gives a much better statistical fit to the observed spectrum. The X ray observations presented here therefore support the hypothesis that ion precipitation is the most likely cause of the Jovian X ray emissions, a result first suggested by the Einstein results (Metzger et al., 1983).

Waite, J. H., Jr.↗
NASA NTRS1974

A time-dependent diffusion convection model for the long term modulation of cosmic rays

A model is developed which incorporates to first order the direct effects of the time dependent diffusive propagation of interstellar cosmic rays in a slowly changing interplanetary medium. The model provides a physical explanation for observed rigidity-dependent phase lags in modulated spectra (cosmic ray hysteresis). The average distance to the modulating boundary during the last solar cycle is estimated.

Gallagher, J. J.↗
NASA NTRS1989

Large liquid rocket engine transient performance simulation system

Phase 1 of the Rocket Engine Transient Simulation (ROCETS) program consists of seven technical tasks: architecture; system requirements; component and submodel requirements; submodel implementation; component implementation; submodel testing and verification; and subsystem testing and verification. These tasks were completed. Phase 2 of ROCETS consists of two technical tasks: Technology Test Bed Engine (TTBE) model data generation; and system testing verification. During this period specific coding of the system processors was begun and the engineering representations of Phase 1 were expanded to produce a simple model of the TTBE. As the code was completed, some minor modifications to the system architecture centering on the global variable common, GLOBVAR, were necessary to increase processor efficiency. The engineering modules completed during Phase 2 are listed: INJTOO - main injector; MCHBOO - main chamber; NOZLOO - nozzle thrust calculations; PBRNOO - preburner; PIPE02 - compressible flow without inertia; PUMPOO - polytropic pump; ROTROO - rotor torque balance/speed derivative; and TURBOO - turbine. Detailed documentation of these modules is in the Appendix. In addition to the engineering modules, several submodules were also completed. These submodules include combustion properties, component performance characteristics (maps), and specific utilities. Specific coding was begun on the system configuration processor. All functions necessary for multiple module operation were completed but the SOLVER implementation is still under development. This system, the Verification Checkout Facility (VCF) allows interactive comparison of module results to store data as well as provides an intermediate checkout of the processor code. After validation using the VCF, the engineering modules and submodules were used to build a simple TTBE.

Mason, J. R.↗
DOE OSTI2025

High efficiency RF sources developments

Calabazas Creek Research, Inc. (CCR) and its collaborators are developing high efficiency RF sources operating from a few hundred MHz to C-Band and power levels from tens to hundreds of kilowatts with the goal of providing MW-relevant sources. The efficiencies approach or exceed 80% with projected costs as low as $0.50/ Watt. Sources under development include magnetrons with phase and amplitude control, single and multi-beam klystrons, multi-beam power grid tubes, and multiple beam IOTs. A magnetron system achieved more than 80% efficiency with fast amplitude control using modulation of the phase locking signal. This would be a low cost, high efficiency RF source for superconducting accelerators. An L-Band, single beam klystron was built with simulated efficiency of 80%. The klystron has yet to be tested to confirm the simulation results. CCR is currently developing a multi-beam klystron to produce more than 200 kW CW at 80% efficiency. Also in development is a multiple beam triode to produce 200 kW CW from 300 MHz to approximately 1 GHz. Not only does the simulated efficiency exceed 75%, but it would be the lowest cost RF source in this frequency range. Finally, CCR recently concluded research for a multiple beam IOT at 700 MHz using third harmonic drive to boost efficiency toward 85%. Successful development and transition to production of these sources will significantly alter the cost/performance landscape for RF power generation.

43 PARTICLE ACCELERATORS↗
NASA NTRS2015

Spin Forming Aluminum Crew Module (CM) Metallic Aft Pressure Vessel Bulkhead (APVBH) - Phase II

The principal focus of this project was to assist the Multi-Purpose Crew Vehicle (MPCV) program in developing a spin forming fabrication process for manufacture of the Orion crew module (CM) aft pressure vessel bulkhead. The spin forming process will enable a single piece aluminum (Al) alloy 2219 aft bulkhead resulting in the elimination of the current multiple piece welded construction, simplify CM fabrication, and lead to an enhanced design. Phase I (NASA TM-2014-218163, (1)) of this assessment explored spin forming the single-piece CM forward pressure vessel bulkhead. The MPCV Program and Lockheed Martin (LM) recently made two critical decisions relative to the NESC Phase I work scope: (1) LM selected the spin forming process to manufacture a singlepiece aft bulkhead for the Orion CM, and (2) the aft bulkhead will be manufactured from Al 2219. Based on the Program's new emphasis related to the spin forming process, the NESC was asked to conduct a Phase II assessment to assist in the LM manufacture of the aft bulkhead and to conduct a feasibility study into spin forming the Orion CM cone. This activity was approved on June 19, 2013. Dr. Robert Piascik, NASA Technical Fellow for Materials at the Langley Research Center (LaRC), was selected to lead this assessment. The project plan was approved by the NASA Engineering and Safety Center (NESC) Review Board (NRB) on July 18, 2013. The primary stakeholders for this assessment are the NASA and LM MPCV Program offices. Additional benefactors are commercial launch providers developing CM concepts.

Hoffman, Eric K.↗
NASA NTRS2015

Spin Forming Aluminum Crew Module (CM) Metallic Aft Pressure Vessel Bulkhead (APVBH) - Phase II

The principal focus of this project was to assist the Multi-Purpose Crew Vehicle (MPCV) Program in developing a spin forming fabrication process for manufacture of the Orion crew module (CM) aft pressure vessel bulkhead. The spin forming process will enable a single piece aluminum (Al) alloy 2219 aft bulkhead resulting in the elimination of the current multiple piece welded construction, simplify CM fabrication, and lead to an enhanced design. Phase I (NASA TM-2014-218163 (1)) of this assessment explored spin forming the single-piece CM forward pressure vessel bulkhead. The Orion MPCV Program and Lockheed Martin (LM) recently made two critical decisions relative to the NESC Phase I work scope: (1) LM selected the spin forming process to manufacture a single-piece aft bulkhead for the Orion CM, and (2) the aft bulkhead will be manufactured from Al 2219. Based on the Program's new emphasis related to the spin forming process, the NESC was asked to conduct a Phase II assessment to assist in the LM manufacture of the aft bulkhead and to conduct a feasibility study into spin forming the Orion CM cone. This activity was approved on June 19, 2013. Dr. Robert Piascik, NASA Technical Fellow for Materials at the Langley Research Center (LaRC), was selected to lead this assessment. The project plan was approved by the NASA Engineering and Safety Center (NESC) Review Board (NRB) on July 18, 2013. The primary stakeholders for this assessment were the NASA and LM MPCV Program offices. Additional benefactors are commercial launch providers developing CM concepts.

Hoffman, Eric K.↗
NASA NTRS2004

Serial-Turbo-Trellis-Coded Modulation with Rate-1 Inner Code

Serially concatenated turbo codes have been proposed to satisfy requirements for low bit- and word-error rates and for low (in comparison with related previous codes) complexity of coding and decoding algorithms and thus low complexity of coding and decoding circuitry. These codes are applicable to such high-level modulations as octonary phase-shift keying (8PSK) and 16-state quadrature amplitude modulation (16QAM); the signal product obtained by applying one of these codes to one of these modulations is denoted, generally, as serially concatenated trellis-coded modulation (SCTCM). These codes could be particularly beneficial for communication systems that must be designed and operated subject to limitations on bandwidth and power. Some background information is prerequisite to a meaningful summary of this development. Trellis-coded modulation (TCM) is now a well-established technique in digital communications. A turbo code combines binary component codes (which typically include trellis codes) with interleaving. A turbo code of the type that has been studied prior to this development is composed of parallel concatenated convolutional codes (PCCCs) implemented by two or more constituent systematic encoders joined through one or more interleavers. The input information bits feed the first encoder and, after having been scrambled by the interleaver, enter the second encoder. A code word of a parallel concatenated code consists of the input bits to the first encoder followed by the parity check bits of both encoders. The suboptimal iterative decoding structure for such a code is modular, and consists of a set of concatenated decoding modules one for each constituent code connected through an interleaver identical to the one in the encoder side. Each decoder performs weighted soft decoding of the input sequence. PCCCs yield very large coding gains at the cost of a reduction in the data rate and/or an increase in bandwidth.

Divsalar, Dariush↗
DOE OSTI2026

Module Testing Procedures and Results for the CMS Phase-2 Outer Tracker Upgrade at Fermilab

The High-Luminosity LHC (HL-LHC) will operate at significantly increased luminosities and is expected to deliver about 3000 $fb^{-1}$ of proton-proton collision data at $\sqrt{s}=14$ TeV over a decade of operation. To maintain efficient tracking and triggering performance under high pileup and radiation conditions, the CMS experiment is upgrading its tracking detector for Phase-2 operations. The upgraded Outer Tracker (OT) will consist of Pixel-Strip (PS) and Strip-Strip (2S) silicon modules capable of providing tracking information to the Level-1 trigger at 40 MHz. Production and qualification of OT modules have been ongoing for about one year across several assembly and testing centers in the US, Europe, India, and Pakistan, requiring extensive testing to ensure stable operation in the HL-LHC environment. Fermilab is responsible for the production and testing of a significant fraction of the OT modules. The testing activities include IV characterization of silicon sensors, noise and pedestal measurements, verification of communication between module components, and burn-in studies using cold-box systems operated under controlled thermal conditions. Results from module testing and qualification studies performed during production will be presented.

Baradia, Sweta [UC, Davis (main)]↗
NASA NTRS2003

Diffraction Efficiency of Thin Film Holographic Beam Steering Devices

Dynamic holography has been demonstrated as a method for correcting aberrations in space deployable optics, and can also be used to achieve high-resolution beam steering in the same environment. In this paper, we consider some of the factors affecting the efficiency of these devices. Specifically, the effect on the efficiency of a highly collimated beam from the number of discrete phase steps per period is considered for a blazed thin film beam steering grating. The effect of the number of discrete phase steps per period on steering resolution is also considered. We also present some result of Finite-Difference Time-Domain (FDTD) calculations of light propagating through liquid crystal "blazed" gratings. Liquid crystal gratings are shown to spatially modulate both the phase and amplitude of the propagating light.

Titus, Charles M.↗
DOE OSTI2025

Isoreticular Tolerance and Phase Selection in the Synthesis of Multi‐Module Metal–Organic Frameworks for Gas Separation and Electrocatalytic OER

Abstract Although metal–organic frameworks are coordination‐driven assemblies, the structural prediction and design using metal‐ligand interactions can be unreliable due to other competing interactions. Leveraging non‐coordination interactions to develop porous assemblies could enable new materials and applications. Here, we use a multi‐module MOF system to explore important and pervasive impact of ligand‐ligand interactions on metal‐ligand as well as ligand‐ligand co‐assembly process. It is found that ligand‐ligand interactions play critical roles on the scope or breakdown of isoreticular chemistry. With cooperative di‐ and tri‐topic ligands, a family of Ni‐MOFs has been synthesized in various structure types including partitioned MIL‐88‐acs ( pacs ), interrupted pacs (i‐ pacs ), and UMCM‐1‐muo. A new type of isoreticular chemistry on the muo platform is established between two drastically different chemical systems. The gas sorption and electrocatalytic studies were performed that reveal excellent performance such as high C 2 H 2 /CO 2 selectivity of 21.8 and high C 2 H 2 uptake capacity of 114.5 cm 3 /g at 298 K and 1 bar.

Xiao, Yuchen [Department of Chemistry University o↗