Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASMA LAYER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Spectroscopic Observation of the Stardust Re-Entry in the Near UV with SLIT: Deduction of Surface Temperatures and Plasma Radiation

Thermal radiation of the heat-shield and the emission of the post-shock layer around the Stardust capsule, during its re-entry, were detected by a NASA-led observation campaign aboard NASA's DC-8 airborne observatory involving teams from several nations. The German SLIT experiment used a conventional spectrometer, in a Czerny-Turner configuration (300 mm focal length and a 600 lines/mm grating), fed by fiber optics, to cover a wavelength range from 324 nm to 456 nm with a pixel resolution of 0.08 nm. The reentering spacecraft was tracked m uansuinaglly a camera with a view angle of 20 degrees, and light from the capsule was collected using a small mirror telescope with a view angle of only 0.45 degrees. Data were gathered with a measurement frequency of 5 Hz in a 30-second time interval around the point of maximum heating until the capsule left the field of view. The emission of CN (as a major ablation product), N2(+) and different atoms were monitored successfully during that time. Due to the nature of the experimental set up, spatial resolution of the radiation field was not possible. Therefore, all measured values represent an integration of radiation from the visible part of the glowing heat shield, and from the plasma in the post-shock region. Further, due to challenges in tracking not every spectrum gathered contained data. The measured spectra can be split up into two parts: (i) continuum spectra which represent a superposition of the heat shield radiation and the continuum radiation of potential dust particles in the plasma, and (ii) line spectra from the plasma in the shock layer. Planck temperatures (interpreted as the surface temperatures of the Stardust heat shield) were determined assuming either a constant surface temperature, or a temperature distribution deduced from numerical simulation. The constant surface temperatures are in good agreement with numerical simulations, but the peak values at the stagnation point are significantly lower than those in the numerical simulation if a temperature distribution over the surface is assumed. Emission bands of CN and N2(+) were tracked along the visible trajectory and compared to a spectral simulation with satisfying agreement. Values for the integrated radiation of the transitions of interest for these species were extracted from this comparison.

Winter, Michael W.↗
NASA NTRS1987

Conditions for double layers in the Earth's magnetosphere and perhaps in other astrophysical objects

Double layers form along auroral field lines in the Earth's magnetosphere. They form in order to maintain current continuity in the ionosphere in the presence of a magnetospheric electric field E with nabla x E is not equal to 0. Features which govern the formation of the double layers are: (1) the divergence of E, (2) the conductivity of the ionosphere, and (3) the current-voltage characteristics of auroral magnetic field lines. Astrophysical situations where nabla x E is not equal to 0 is applied to a conducting plasma similar to the Earth's ionosphere are potential candidates for the formation of double layers. The region with nabla x E is not equal to 0 can be generated within, or along field lines connected to, the conducting plasma. In addition to nabla x E, shear neutral flow in the conducting plasma can also form double layers.

Lyons, L. R.↗
NASA NTRS1985

The physics of comets

This volume of the 'Fundamentals of Cosmic Physics' is concerned with the physics of comets. Aspects regarding the nucleus are discussed, taking into account observations, radius and albedo, mass, rotation, splitting and disruption, the temperature and sublimation of the cometary nucleus, the chemical composition, the electrostatic charging of the cometary nucleus, and the structure and evolution of the cometary nucleus. Other topics explored are related to the atmosphere and its interaction with the solar wind, the plasma tail, and the dust tail. Attention is given to excitation mechanisms, atmospheric abundances and production rates, chemical models of the inner coma, collisional processes and the multifluid approach, radiative transfer, the ionization processes, models of the inner layer, the outer coma, acceleration mechanisms in the plasma tail, the structure of the plasma tail, the cometary magnetosphere, dust grain orbits, gas-dust interaction in the inner coma, and the nature of the cometary dust.

Mendis, D. A.↗
NASA NTRS1985

Thermal barrier coating life-prediction model development

Life predictions are made for two types of strain-tolerant and oxidation-resistant Thermal Barrier Coating (TBC) systems produced by commercial coating suppliers to the gas turbine industry. The plasma-sprayed TBC system, composed of a low-pressure plasma spray (LPPS) applied oxidation-resistant NiCrAlY bond coating and an air-plasma-sprayed yttria (8 percent) partially stabilized zirconia insulative layer, is applied by both Chromalloy and Klock. The second type of TBC is applied by the electron-beam/physical vapor deposition process by Temescal. Thermomechanical and thermochemical testing of the program TBCs is in progress. A number of the former tests has been completed. Fracture mechanics data for the Chromalloy plasma-sprayed TBC system indicate that the cohesive toughness of the zirconia layer is increased by thermal cycling and reduced by high temperature exposure at 1150 C. Eddy current technology feasibility has been established with respect to nondestructively measuring zirconia layer thickness of a TBC system. High pressure turbine blades have been coated with program TBC systems for a piggyback test in a TFE731-5 turbofan factory engine test. Data from this test will be used to validate the TBC life models.

Strangman, T. E.↗
NASA NTRS2001

A Coupled Plasma and Sheath Model for High Density Reactors

We present a coupled plasma and collisionless; sheath model for the simulation of high density plasma processing reactors. Due to inefficiencies in numerical schemes and the resulting computational burden, a coupled multidimensional plasma and sheath simulation has not been possible model for gas mixtures and high density reactors of practical interest. In this work we demonstrate that with a fully implicit algorithm and a refined computational mesh, a self-consistent plasma and sheath simulation is feasible. We discuss the details of the model equations, the importance of ion inertia, and the resulting sheath profiles for argon and chlorine plasmas. We find that at low operating pressures (10-30 mTorr), the charge separation occurs only within a 0.5 mm layer near the surface in a 300 mm inductively coupled plasma etch reactor. A unified model eliminates the use of off-line or loosely coupled sheath models with simplifying assumptions which generally lead to uncertainties in ion flux and sheath electrical properties.

Deepak, Bose↗
NASA NTRS1990

Transition from moving to stationary double layers in a single-ended Q machine

Large-amplitude (less than about 100 percent) relaxation oscillations in the plasma potential are known to be generated when the cold endplate of a single-ended Q machine is biased positively. These oscillations are associated with double layers that form near the hot plate (plasma source) and travel toward the endplate at about the ion-acoustic velocity. At the endplate they dissolve and then form again near the hot plate, the entire process repeating itself in a regular manner. By admitting a sufficient amount of neutral gas into the system, the moving double layers were slowed down and eventually stopped. The production of stationary double layers requires an ion source on the high-potential side of the double layers. These ions are provided by ionization of the neutral gas by electrons that are accelerated through the double layer. The dependence of the critical neutral gas pressure required for stationary double-layer formation on endplate voltage, magnetic field strength, and neutral atom mass has been examined. These results are discussed in terms of a simple model of ion production and loss, including ion losses across the magnetic field.

Song, Bin↗
NASA NTRS1995

Simultaneous prenoon and postnoon observations of three field-aligned current systems from Viking and DMSP-F7

The spatial structure of dayside large-scale field-aligned current (FAC) systems is examined by using Viking and Defense Meteorological Satellite Program-F7 (DMSP-F7) data. We focus on four events in which the satellites simultaneously observed postnoon and prenoon three FAC systems: the region 2, the region 1, and the mantle (referred to as midday region O) systems, from equatorward to poleward. These events provide the most solid evidence to date that the midday region O system is a separate and unique FAC system, and is not an extension of the region 1 system from other local times. The events are examined comprehensively by making use of a mulit-instrumental data set, which includes magnetic field, particle flux, electric field, auroral UV image data from the satellites, and the Sondrestrom convection data. The results are summarized as follows: (1) Region 2 currents flow mostly in the central plasma sheet (CPS) precipitation region, often overlapping with the boundary plasma sheet (BPD) at their poleward edge. (2) The region 1 system is located in the core part of the auroral oval and is confined in a relatively narrow range in latitude which includes the convection reversal. The low-latitude boundary layer, possibly including the outer part of the plasma sheet, and the external cusp are the major source regions of dayside region 1 currents. (2) Midday region O currents flow on open field lines and are collocated with the shear of antisunward convection flows with velocites decreasing poleward. On the basis of these results we support the view that both prenoon and postnoon current systems consist of the three-sheet structure when the disctortion ofthe convection pattern associated with interplanetary magnetic field (IMF) B(sub Y) is small and both morningside and eveningside convection cells are crescent-shaped. We also propose that the midday region O and a part of the region 1 systems are closely coupled to the same source.

Ohtani, S.↗
NASA NTRS2007

Electroform/Plasma-Spray Laminates for X-Ray Optics

Electroform/plasma-spray laminates have shown promise as lightweight, strong, low-thermal-expansion components for xray optics. The basic idea is to exploit both (1) the well-established art of fabrication of optical components by replication and (2) plasma spraying as a means of reinforcing a thin replica optic with one or more backing layer(s) having tailorable thermomechanical properties. In x-ray optics as in other applications, replication reduces the time and cost of fabrication because grinding and polishing can be limited to a few thick masters, from which many lightweight replicas can thereafter be made. The first step in the fabrication of a component of the type in question is to make a replica optic by electroforming a thin layer of nickel on a master. Through proper control of the electroforming process conditions, it is possible to minimize residual stress and, hence, to minimize distortion in the replica. Next, a powder comprising ceramic particles coated with a metal compatible with the electroformed nickel is plasma-sprayed onto the backside of the nickel replica. Then through several repetitions and variations of the preceding steps or perhaps a small compressive stress, alternating layers of electroformed nickel and plasma-sprayed metal-coated ceramic powder are deposited. The thicknesses of the layers and the composition of the metal-coated ceramic powder are chosen to optimize the strength, areal mass density, and toughness of the finished component. An important benefit of using both electroforming and plasma spraying is the possibility of balancing stresses to a minimum level, which could be zero or perhaps a small net compressive stress designed to enhance the function of the component in its intended application.

Ulmer, Melville P.↗
NASA NTRS1989

Propagation and absorption of electron-cyclotron maser radiation during solar flares

The propagation and absorption of the maser radiation during solar flares are examined through linear theory and electromagnetic particle simulations. It is shown using linear theory that strong absorption of the radiation should occur as it propagates toward the second harmonic layer, where the magnetic field is half as strong as in the emission region. Only radiation propagating nearly parallel to the magnetic field in a low-temperature plasma may be able to escape under certain limited conditions. Finite temperature effects can cause radiation propagating nearly perpendicular to the magnetic field to refract, causing enhanced absorption. Particle simulations are then used to evaluate the nonlinear response of the plasma as the maser radiation propagates through the absorption layer. It is shown that some of the maser radiation is able to escape through a process of absorption below the second harmonic of the local gyrofrequency and re-emission above it. The fraction able to escape is much higher than that predicted by linear theory, although the amount of escaping energy is only a small fraction of the incident energy.

Mckean, M. E.↗
NASA NTRS1981

Further determination of the characteristics of magnetospheric plasma vortices with Isee 1 and 2

Further studies of the vortices in magnetospheric plasma flow with the Los Alamos Scientific Laboratory/Max-Planck-Institut (LASL/MPI) fast plasma experiment on Isee 1 and 2 have revealed that the pattern of vortical flow has a wavelength of approximately 20-40 earth radii and moves tailward through the magnetosphere at speeds of several hundred kilometers per second. The tendency toward vorticity pervades the total breadth of the plasma sheet tailward of the dawn-dusk meridian. The sense of rotation of the plasma flow (as viewed from above the ecliptic plane) is clockwise in the morning side of the plasma sheet and counterclockwise in the evening side. The sense of rotation in the morning and evening boundary layers is reversed from that in the contiguous regions of the plasma sheet. The occurrence of vortical flow is independent of the level of geomagnetic activity but is associated with long-period geomagnetic pulsations.

Hones, E. W., Jr.↗
NASA NTRS1984

Numerical simulations of double layers and auroral electric fields

Recent one-dimensional and two-dimensional numerical simulations of double layers (DLs) in the electric fields of the auroral plasma are reviewed, with reference to observational data. It is found that two-dimensional DLs driven by current sheets of finite thickness have different characteristics, depending on whether the layer thickness is less than or much greater than the ion gyroradius: When thickness is less than ion gyroradius, V-shaped DLs form with nearly equal parallel and perpendicular potential drops; when layer thickness is much greater than ion gyroradius the major parallel potential drop occurs outside the current sheet and the perpendicular electric fields are localized at the edges of the current sheet. It is shown that some features of the simulated fields, such as the amplitudes and scale lengths, are qualitatively similar to those observed in space.

Singh, N.↗
NASA NTRS1972

Fast Faraday fading of long range satellite signals.

20 MHz radio signals have been received during the day from satellite Beacon-B when it was below the optical horizon by using a bank of narrow filters to improve the signal to noise ratio. The Faraday fading rate becomes constant, under these conditions, at a level determined by the plasma frequency just below the F-layer peak. Variations in the Faraday fading rate reveal fluctuations in the electron density near the peak, while the rate of attaining the constant level depends on the shape of the electron density profile.

Heron, M. L.↗
NASA NTRS1975

Continued development of abradable gas path seals

Major program objectives were the continued development of NiCrAlY feltmetal and honeycomb systems for knife edge seal applications in the 1144 to 1366 K temperature range, and to initiate abradable seal material evaluation for blade tip seal applications in the 1366 to 1589 K temperature range. Larger fiber size, higher density feltmetal showed greatly improved erosion resistance with a slight reduction in abradability compared to the baseline feltmetal. Pack aluminide coating of the honeycomb extended the oxidation resistance and slightly improved the abradability of this material. Evaluation through selected abradability, erosion and oxidation testing, and pertinent metallography led to selection of a plasma sprayed yttria stabilized zirconia (ZrO2)/CoCrAlY layered system as the system with the most potential to meet the 1589 K requirement for blade tip seals. This system demonstrated structural integrity, erosion resistance, and some degree of abradability.

Shiembob, L. T.↗
NASA NTRS1981

Transient brightenings of interconnecting loops. II - Dynamics of the brightened loops

Three different kinds of dynamic events related to interconnecting loops observed in soft X-rays aboard Skylab are discussed: (1) a newly born transequatorial loop that was either emerging from subphotospheric layers or gradually filled in with hot plasma; (2) large-scale twists of interconnecting loops which never relax, and often only form after the loop brightenings, and (3) three events where the loop that later interconnected two active regions had been visible long before one of the interconnecting regions was born. Several impacts this observation might have upon the understanding of the process of flux emergence are suggested.

Svestka, Z.↗
NASA NTRS1985

Energetic particle observations in the low-latitude boundary layer

Energetic (approximately equal to or greater than 24 keV) particle three-dimensional distributions are presented, taking into account a dawnside (approximately 0515 LT) and duskside (approximately 1845 LT) traversal of the magnetopause boundary regions during periods of northward magnetosheath magnetic field. The boundary region traversed is identified as the low-latitude boundary layer (LLBL) on the basis of survey plasma data, the energetic particle distributions, and magnetic field behavior. The main features of the energetic particle data for these two passes are discussed. On the basis of an analysis of the obtained data, it is concluded that the dawn and dusk LLBL are on closed geomagnetic field lines. It is found that the plasma sheet is the main source of energetic LLBL particles. The possibility exists that the tailward convecting particles in the LLBL reenter the plasma sheet at some further distance in the tailward direction.

Williams, D. J.↗
NASA NTRS1986

Science applications

Possible scientific applications in the field of the neutral ionized atmosphere and of the solid Earth in terms of the TSS are summarized. Studies of the vertical, zonal, and meridional neutral winds and temperature, whose extensive variations suggest the importance of energy transfer mechanism in modifying the structural properties of the region are reviewed. Layers below the F region of high plasma density that propagate to lower altitudes with drift velocities will be studied for their electron and ion composition and motion. These are to be measured by the TSS in conjunction with ground based radar observations. Basic fluid dynamics problems will be studied onboard tethered satellites. Studies will be conducted on the structure of the equatorial electrojet, in particular its longitudinal and meridional extent. Magnetic measurements will also be used to probe the tether current distribution in the plasma sheath.

Mariani, F.↗
NASA NTRS1986

Thermal barrier coating life-prediction model development

The program focuses on predicting the lives of two types of strain-tolerant and oxidation-resistant thermal barrier coating (TBC) systems that are produced by commercial coating suppliers to the gas turbine industry. The plasma-sprayed TBC system, composed of a low-pressure plasma-spray (LPPS) or an argon shrouded plasma-spray (ASPS) applied oxidation resistant NiCrAlY or (CoNiCrAlY) bond coating and an air-plasma-sprayed yttria partially stabilized zirconia insulative layer, is applied by both Chromalloy, Klock, and Union Carbide. The second type of TBS is applied by the electron beam-physical vapor deposition (EB-PVD) process by Temescal. The second year of the program was focused on specimen procurement, TMC system characterization, nondestructive evaluation methods, life prediction model development, and TFE731 engine testing of thermal barrier coated blades. Materials testing is approaching completion. Thermomechanical characterization of the TBC systems, with toughness, and spalling strain tests, was completed. Thermochemical testing is approximately two-thirds complete. Preliminary materials life models for the bond coating oxidation and zirconia sintering failure modes were developed. Integration of these life models with airfoil component analysis methods is in progress. Testing of high pressure turbine blades coated with the program TBS systems is in progress in a TFE731 turbofan engine. Eddy current technology feasibility was established with respect to nondestructively measuring zirconia layer thickness of a TBC system.

Strangman, T. E.↗
NASA NTRS1985

Development of thermomechanical life prediction models for thermal barrier coatings

Thermal barrier coatings (TBCs) for turbine airfoils in high-performance engines represent an advanced materials technology with both performance and durability benefits. The foremost TBC benefit is the reduction of heat transferred into air-cooled components. To achieve these benefits, however, the TBC system must be reliable. Mechanistic thermomechanical and thermochemical life models and statistically significant design data are therefore required for the reliable exploitation of TBC benefits on gas turbine airfoils. Garrett's NASA-HOST Program (NAS3-23945) is designed to fulfill these requirements. This program focuses on predicting the lives of two types of strain-tolerant and oxidation-resistant TBC systems that are produced by commercial coating suppliers to the gas turbine industry. The plasma-sprayed TBC system, composed of a low-pressure plasma-spray (LPPS) applied oxidation resistant NiCrAlY bond coating, and an air-plasma-sprayed yttria partially stabilized zirconia insulated layer is applied by both Chromalloy and Klock. The second type of TBC is applied by the electron beam-physical vapor deposition process by Temescal. Thermomechanical life models are being tailored to predict TBC strain tolerance in terms of materials, engine, and mission parameters. Continuum and fracture mechanics approaches and statistical methods are being evaluated to develop tensile and compressive strain functions required to drive a mission analysis capable thermomechanical life model for TBCs. Results of initial testing to calibrate these life models will be presented.

Strangman, T. E.↗