Search NASA⌕ Search

SEARCH · Search NASA

Results for “REACTOR OPERATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Innovative use of Cr(VI) plume depictions and pump-and-treat capture analysis to estimate risks of contaminant discharge to surface water at Hanford reactor areas - 15315

The Hanford Site nuclear reactor operations required large quantities of high-quality cooling water, which was treated with chemicals including sodium dichromate dihydrate for corrosion control. Cooling water leakage, as well as intentional discharge of cooling water to ground during upset conditions, produced extensive groundwater recharge mounds consisting largely of contaminated cooling water and resulted in wide distribution of hexavalent chromium (Cr[VI]) contamination in the unconfined aquifer. The 2013 Cr(VI) groundwater plumes in the 100 Areas cover approximately 6 km{sup 2} (1500 acres), primarily in the 100-HR-3 and 100-KR-4 groundwater operable units (OUs). The Columbia River is a groundwater discharge boundary; where the plumes are adjacent to the Columbia River there remains a potential to discharge Cr(VI) to the river at concentrations above water quality criteria. The pump-and-treat systems along the River Corridor are operating with two main goals: 1) protection of the Columbia River, and 2) recovery of contaminant mass. An evaluation of the effectiveness of the pump-and-treat systems was needed to determine if the Columbia River was protected from contamination, and also to determine where additional system modifications may be needed. In response to this need, a technique for assessing the river protection was developed which takes into consideration seasonal migration of the plume and hydraulic performance of the operating well fields. Groundwater contaminant plume maps are generated across the Hanford Site on an annual basis. The assessment technique overlays the annual plume and the capture efficiency maps for the various pump and treat systems. The river protection analysis technique was prepared for use at the Hanford site and is described in detail in M.J. Tonkin, 2013. Interpolated capture frequency maps, based on mapping dynamic water level observed in observation wells and derived water levels in the vicinity of extraction and injection wells, are developed initially. Second, simulated capture frequency maps are developed, based on transport modelling results. Both interpolated and simulated capture frequency maps are based on operation of the systems over a full year. These two capture maps are then overlaid on the plume distribution maps for inspection of the relative orientation of the contaminant plumes with the capture frequency. To quantify the relative degree of protection of the river from discharges of Cr(VI) (and conversely, the degree of threat) at any particular location, a systematic method of evaluating and mapping the plume/capture relationship was developed. By comparing the spatial relationship between contaminant plumes and hydraulic capture frequency, an index of relative protectiveness is developed and the results posted on the combined plume/capture plan view map. Areas exhibiting lesser degrees of river protection are identified for remedial process optimization actions to control plumes and prevent continuing discharge of Cr(VI) to the river. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Development of physics-consistent conditional diffusion model to overcome data scarcity in critical heat flux

Deep generative modeling provides a powerful pathway to overcome data scarcity in energy-related applications where experimental data are often limited. By learning the underlying probability distribution of the training dataset, deep generative models, such as the diffusion model, can generate high-fidelity synthetic samples that statistically resemble the training data. Such synthetic data generation can significantly enrich the size and diversity of the available training data, and more importantly, improve the robustness of downstream machine learning models in predictive tasks. The objective of this paper is to investigate the effectiveness of diffusion models for overcoming data scarcity in nuclear energy applications. By leveraging a public dataset on critical heat flux which covers a wide range of commercial nuclear reactor operational conditions, we developed a diffusion model that can generate an arbitrary amount of synthetic samples. Since a vanilla diffusion model can only generate samples randomly, we also developed a conditional diffusion model capable of generating targeted critical heat flux data under user-specified thermal-hydraulic conditions. The performance of the diffusion model was evaluated based on its ability to capture empirical feature distributions and pair-wise correlations, as well as to maintain physical consistency. The results showed that both the diffusion model and conditional diffusion model can successfully generate realistic and physics-consistent critical heat flux data. Furthermore, uncertainty quantification results demonstrate that the conditional diffusion model is highly effective in augmenting critical heat flux data while maintaining acceptable levels of uncertainty.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Radionuclide stochastic distribution in the irradiated graphite - 15206

In France, about 17,000 tons of irradiated graphite waste will be produced from the decommissioning of the six gas-cooled nuclear reactors operated by Electricite De France (EDF). Radionuclide measurements in irradiated graphite exhibit very high discrepancies especially when corresponding to precursors at trace level which is often the case for nuclear grade graphite. As evidenced by numerous studies nuclear graphite is a very pure material, however, it cannot be considered from an analytical viewpoint as a typical homogeneous material. Geo-statistics do not give any notable results when the 3D neutron flux and power history are known. Without taking into account the very origin of the stochastic behavior of radionuclide, their properties may be assumed with the statistical properties which are used in the case of contaminated soils but which have no interest for irradiated graphite. At every scale, the huge discrepancy cannot be avoided but can be easily explained by Theory Of Sampling (TOS) of finely divided materials. The complexity of nuclear graphite is due to its high purity. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Analysis and Thermal Property Investigations into Ternary Actinide Chloride Salt Systems Containing UCl3 and PuCl3

While regulators, the scientific community, and MSR developers still lack access to literature data on the thermal properties of clean fuel salts, even less information is available on the properties of fuel salts containing impurities. It is essential to understand, benchmark, and predict crucial data on the changes in thermal properties of fuel salt systems due to impurities arising from moisture, corrosion, and reactor operation (i.e., fission products). This research focuses on two actinide fuel salts (1) to investigate a worst-case scenario buildup of actinide fission product in a NaCl-UCl3 eutectic fuel salt and (2) to investigate NaCl-PuCl3 eutectic salt after 1000 hours of operation in a natural circulation flow loop flow to determine if corrosion or atmospheric (moisture/oxygen) products are present. For the first salt, a conservative assumption or worst-case scenario, for fission product buildup in a fuel salt was investigated by adding PuCl3 to eutectic 67 mol% NaCl – 33 mol% UCl3 salt resulting in a ternary salt having a composition of 61 mol% NaCl – 30 mol% UCl3 – 9mol% PuCl3. Addition of PuCl3 to eutectic NaCl-UCl3 resulted in a ternary salt that had a higher melting temperature than either the NaCl-PuCl3 or NaCl-UCl3 binary eutectic mixture. Addition of PuCl3 also resulted in an increase in density which was expected. The second salt was extracted from a micro loop. The composition of the fuel (primary) salt prior to flow loop operations was determined to be 64 mol% NaCl – 36 mol% PuCl3, however, the post-flow loop salt showed increased levels of MgCl2 and NaCl changing the salt composition to 10 mol% MgCl2 – 63mol% NaCl – 26mol% PuCl3) indicating the primary salt interacted with the rinse salt. Analysis of the post flow loop salt detected low concentrations of Al, Ni, Co, Nb, and Zr, most likely corrosion products from the flow loop material of construction. Contamination of the fuel salt (with the rinse salt NaCl-MgCl2) decreased the density by approximately 10% and reduced the onset of melting temperature by 50 °C, from 451 °C to approximately 400 °C. Results from the fission product simulated salt (61 mol% NaCl – 30 mol% UCl3 – 9mol% PuCl3) and the corrosion product salt (10 mol% MgCl2 – 63mol% NaCl – 26mol% PuCl3) will be included in two separate manuscripts for submission to peer-reviewed journals.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The synthesis and air oxidation behavior of U-Si-Al and U-Si-B compositions

Uranium silicide intermetallic compounds are currently under investigation by the DOE-NE Advanced Fuels Campaign as candidate accident tolerant nuclear fuel concepts for light water reactors. While many U-Si compounds offer benefits compared to reference UO{sub 2} in terms of heavy metal density and thermal conductivity, they have been shown to display poor resistance to oxidizing atmospheres above 400 Celsius degrees. The general oxidation behavior of all U-Si compounds is oxidation of uranium; formation of UO{sub 2} followed by U{sub 3}O{sub 8} leads to rapid pulverization of the material. It is hypothesized that introducing an additional compositional degree of freedom by exploring U-Si-X (X=Al or B) ternary systems may provide the means to design a candidate nuclear fuel which optimizes the benefits of each binary. Phase analysis and preliminary oxidation testing were performed on four compositions containing alloying additions to U{sub 3}Si{sub 2} and U{sub 3}Si{sub 5}. Aluminum additions to U{sub 3}Si{sub 2} were observed to increase the oxidation resistance by delaying the onset of oxidation during synthetic air ramp testing. U{sub 3}Al{sub 2}Si{sub 3} delayed the onset of oxidation to T>650 C. degrees. During a 10 hour isothermal hold at 400 C. degrees in air the compound gained very little mass, indicating that it could be stable at reactor operating temperatures. Further analysis of this material is necessary to determine its oxidation behavior in steam and determine the specific mechanism that is providing the delayed oxidation. Boron additions to U{sub 3}Si{sub 5} do not appear to provide any additional oxidation resistance to the compound as tested in this work. The 1.67 at.% addition of B produced primarily single-phase composition. Melting and sintering studies followed by further compositional and thermal analyses are required to advance this composition as a candidate composite fuel additive. Lastly, the nominally U{sub 3}BSi{sub 4} composition produced a multi-phase system which provided no additional oxidation resistance following either a synthetic air ramp oxidation test or a pre-passivation isothermal hold at 800 C. degrees.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Synthesis and Thermophysical Property Determination of NaCl-PuCl3 Salts

Currently, a knowledge gap exists in the available data and understanding of thermophysical properties relating to fresh fuel salts, especially those containing plutonium. Determination of this data is necessary for the design and construction of test reactors, as well as the licensing of future commercial molten salt reactors. Thermophysical properties such as melting temperature, salt stability, density, and heat capacity were determined on synthesized eutectic NaCl-PuCl3 and a more sodium rich composition containing 25 mol% PuCl3. These measurements document the baseline properties of the salt as a function of temperature for future experiments on irradiated fuel salt which will provide a holistic perspective on the change of thermophysical properties during reactor operations. It was determined that the NaCl-PuCl3 ingot synthesized for this study contained 63.4 mol% NaCl, 36.3 mol% PuCl3, and was 99.7% pure. Upon heating it was shown that the NaCl- PuCl3 eutectic was stable at temperatures of 800°C. The onset of melting occurred at 541°C and the enthalpy of fusion was determined to be 140.7 ± 8.4 J/g. Specific heat capacity measurements showed a slightly decreasing trend with respect to temperature in the liquid phase ranging from 0.67 to 0.57 J/g·K, with an average value of 0.637 ± 0.03 J/g·K (104 ± 5 J/mol·K) between 500 to 720°C. Three independent trials of the molten NaCl-PuCl3 eutectic salt found the density to be ?(T) = 3.8589 – 9.5342·10-4 T(°C), validated between 500 to 800°C. In addition to salt synthesis and experimentally determining thermodynamic properties, Ab Initio molecular dynamic (AIMD) simulations were used to calculate density and heat capacity values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Dehalogenation reactions between halide salts and phosphate compounds

Reactions between phosphoric acid [H 3 PO 4 ] or ammonium hydrogen phosphates [i.e., NH 4 H 2 PO 4 , (NH 4 ) 2 HPO 4 ] and halide salts can be used to dehalogenate (remove halides from) salt-based waste streams, where the process of removing halides yields products that have more efficient disposal pathways for repository storage. In this context, the term efficiency is defined as higher waste loadings and simplified immobilization processes with potential for recycle of certain salt components (e.g., 37 Cl as H 37 Cl or NH 4 37 Cl). The main streams identified for these processes are nuclear wastes generated during electrochemical reprocessing of used nuclear fuel as well as used halide salts from molten salt reactor operation. The potential byproducts of these reactions are fairly consistent across the range of halide species (i.e., F, Cl, Br, I) where the most common are hydrogen halides [e.g., HCl (g) ] or ammonium halides (e.g., NH 4 Cl). However, trihalide compounds (e.g., NCl 3 ), nitrogen triiodide ammine adducts [NI 3 ·(NH 3 ) x ], and ammonium triiodide (NH 4 I 3 ) are also possible. Several of these byproducts (i.e., NCl 3 , NBr 3 , NI 3 , and NH 4 I 3 ) are shock-sensitive contact explosives so their production in these processes must be tracked and carefully controlled, which includes methods of immediate neutralization upon production such as direct transport to a caustic scrubber for dissolution. Several benefits arise from utilizing H 3 PO 4 as the phosphate additive during dehalogenation reactions for making iron phosphate waste forms including more oxidized iron (higher Fe 3+ :Fe 2+ ratios), higher chemical durabilities, and the avoidance of trihalides, but the byproducts are hydrogen halides, which are corrosive and require special handling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of Macroscale Models of UO 2 Fuel Sintering and Densification using Multiscale Modeling and Simulation

Light water reactor fuel pellets are fabricated using sintering to final densities of 95% or greater. During reactor operation, the porosity remaining in the fuel after fabrication decreases further due to irradiation-assisted densification. While empirical models have been developed to describe this densification process, a mechanistic model is needed as part of the ongoing work by the NEAMS program to develop a more predictive fuel performance code. In this work we will develop a phase field model of sintering of UO 2 in the MARMOT code, and validate it by comparing to published sintering data. We will then add the capability to capture irradiation effects into the model, and use it to develop a mechanistic model of densification that will go into the BISON code and add another essential piece to the microstructure-based materials models. The final step will be to add the effects of applied fields, to model field-assisted sintering of UO 2 . The results of the phase field model will be validated by comparing to data from field-assisted sintering. Tasks over three years: 1. Develop a sintering model for UO 2 in MARMOT 2. Expand model to account for irradiation effects 3. Develop a mechanistic macroscale model of densification for BISON

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of process parameters and post-build conditions for qualification of LPBF 316 SS

To harness the potential of laser powder bed fusion (LPBF) 316H stainless steel (SS) for use in advanced nuclear reactors, extensive research efforts are needed to develop optimal laser processing parameters and appropriate heat treatments, taking into account various manufacturing platforms and locations. Furthermore, it is crucial to assess the material properties in environments relevant to reactor operating conditions. In collaboration with Oak Ridge National Laboratory (ORNL) and Los Alamos National Laboratory (LANL), Argonne National Laboratory (ANL) is dedicated to gaining insights into how the manufacturing process and post-build treatments impact the performance of LPBF 316H SS. This report provides an overview of ANL's research findings for FY23, focusing on LPBF 316H SS produced using a Renishaw AM400 laser system. Specifically, our research has concentrated on three key areas: 1) Optimum laser processing parameters: Leveraging the high-throughput printing technology, we systematically varied the laser power, exposure time and point distance within the same build. By measuring the as-printed porosity, we identified an optimum printing parameter window that produced materials with near-complete density; 2) Post-built treatment development: Materials printed with the optimum laser parameters underwent treatments including stress relief, solution annealing, and hot isostatic pressing. Subsequently, we fabricated tension, creep, and fatigue specimens from materials subjected to these different conditions. Over the next year, a series of scoping tests will be conducted to facilitate the selection of the most suitable post-build treatment condition; 3) Thermal aging effects on microstructure and properties: thermal aging at 550°C, 650°C and 750°C was conducted on LPBF 316H SS specimens up to 2500 h. Microstructural characterization was performed with electron microscopy, and the evolution of the dislocation cell structures and secondary phases was studied. Microhardness tests and tension tests were conducted to quantify changes in mechanical properties. The results revealed that the aged LPBF 316H SS exhibited a high density of Cr-rich and Mo-rich fine precipitates within grains due to the presence of a high density of dislocations and the globally distributed dislocation cell structures, which served as heterogeneous nucleation sites for secondary phases. Along grain boundaries, a Mo-Cr-rich phase, observed in 750°C-aged conditions, displayed significant thermal coarsening. Throughout the aging process, various mechanisms, including stress relaxation, dislocation cell structure recovery, solution hardening, and precipitation hardening, competed to influence materials strength. These results contribute towards establishing the technical basis for qualifying LPBF 316H SS for advanced nuclear reactor applications.

36 MATERIALS SCIENCE↗

A critical analysis of U-Pu-Zr phase transitions using calorimetric, microstructural, and phase equilibria data

Metallic fuels consisting primarily of uranium, plutonium, and zirconium (U-Pu-Zr) are a leading material candidate for fast-spectrum nuclear reactors. Early demonstration programs proved the principle of safe and efficient fast reactor operation, however there is still considerable uncertainty regarding the phase equilibria and microstructural evolution across the ternary composition space. Quantitative phase formation and identification measurements are scarce and often incomplete, with studies reporting either phase transition temperatures or phase identification data, but not both from the same specimens. In this study, we critically compared experimental and calculated phase transition data and correlated with the microstructure and phase characterization data of as-cast and annealed U-Pu-Zr alloys. Differential scanning calorimetry (DSC) was used to measure phase transitions in the subsolidus regions (723−948 K) of three ternary U-Pu-Zr alloys with similar plutonium concentrations but various U/Zr ratios. Due to sluggish kinetics and narrow ranges of phase stability, complex peaks required the use of a Frazier-Suzuki peak fitting algorithm to deconvolute and calculate transition peak temperatures and enthalpies. We also identified trends of phase transition behavior by critically comparing our DSC data with previous phase transition measurements as well as historical and calculated phase equilibrium diagrams. In conclusion, this provides a critical approach for benchmarking and assessing the quality of new U-Pu-Zr phase equilibria data prior to its incorporation into nuclear material databases.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Recent activities of the UK working party on criticality - 14334

The Working Party on Criticality (WPC) in the United Kingdom (UK) is the non-executive national committee that focuses on criticality safety issues up to, but not including, experimental and in-core power reactor operations. The current membership includes representatives from all relevant UK Site Licensee Companies and Regulators together with a small number of other key companies with interests in this area. In recent times, the primary focus of the committee has been to provide a forum for the discussion and distribution of information of relevance to criticality safety in the UK, particularly the sharing and development of good practice. However, it also serves as a useful forum to (i) disseminate regulatory issues of relevance to criticality safety and facilitate the development of a UK criticality community view on such matters, (ii) guide, promote, coordinate and encourage cooperation on high priority activities of common interest to the UK criticality community, (iii) promote international collaboration in the field of criticality safety, and (iv) provide opportunities for the professional development of criticality safety personnel. This paper gives a detailed overview of the activities of the WPC in the years since the last International Conference on Nuclear Criticality (ICNC), held at Edinburgh in 2011. It undoubtedly continued to be a challenging time for the UK criticality community, not least because of difficulties with the central coordination (and hence funding) of strategic issues in the UK as the nuclear industry has become increasingly fragmented. However, despite these issues, the committee has still been able to fulfil its objectives during that time and successfully supported the UK criticality community. A particular focus of the paper will be the success of the Continued Professional Development workshops and the potential benefits of other countries adopting a similar initiative. (author)

42 ENGINEERING↗

Progress on the development of new correlations under the framework of the IAEA Coordinated Research Programme on heat transfer in SCWR's

This paper begins with an introduction designed to provide researchers who are new to field of heat transfer to fluids at supercritical pressure with a brief picture of early developments, and to set the scene for the review of work on the development of new correlations for such fluids under the framework of the IAEA CRP. These are needed because of the active consideration now being given to water-cooled nuclear reactors operating at pressures above the critical value. Work on the development of a trans-critical look-up table aimed at covering the region near the critical point is outlined. A very large heat transfer databank has been compiled and subjected to a thorough screening process. It covers a wide range of conditions and has been used for the assessment of the performance of a number of empirical equations. A detailed error analysis was carried out for the most promising ones and an examination of parametric trends was made. A new correlation is described which has been specifically designed to combine simplicity of structure, explicit connection with physically-based phenomena whilst being able to cover both normal and deteriorated heat transfer conditions. It avoids direct dependence of heat transfer coefficient on wall temperature. The performance of this correlation was evaluated using the data set of Herkenrath et al for water at supercritical pressure. Results from a recent experimental study of heat transfer to carbon dioxide at supercritical pressure under conditions of mixed convection have been used to develop a set of equations to describe the general behaviour observed. Comparisons are made between the performance of a number of equations and the data from the carbon dioxide experiments and also some for water. Finally, the development is outlined of physically-based, semi-empirical models aimed at extending an empirical equation for variable property forced convection heat transfer to fluids at supercritical pressure to account for influences of buoyancy and flow acceleration. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Mechanical testing of hydrided fuel cladding

During light water reactor operations, hydrogen is generated from the oxidation of zirconium alloy materials. This hydrogen can be absorbed into the cladding and form zirconium hydrides. At high temperatures and hoop stresses, these normally circumferential oriented hydrides in high burnup used nuclear fuel (HB-UNF) may reorient in the radial direction and affect the mechanical properties of the cladding. Understanding these changes in mechanical properties will aid in analyzing how UNF will perform during storage and transportation. Systems, presented in the article, have been designed to introduce hydrides into cladding specimens, to reorient cladding hydrides, and to test and measure the mechanical properties of these specimens. The hydriding systems consist of a tube furnace capable of pre-hydriding cladding specimens and reorienting cladding hydrides and surface conditioning equipment. Mechanical testing (i.e., tensile, compression, and burst testing) will be performed on both pre-hydrided cladding and cladding with reoriented hydrides, and the results will be compared with those of as-manufactured cladding. Tensile and compression testing will be performed using a 5 kilo-pound load frame; burst testing will be performed on a purpose-built test system. Strain is measured with a digital image correlation (DIC) system. DIC is a real time optical measurement technique that utilizes high-definition imagery to measure object deformation. It is planned that tensile, compression, and burst testing of cladding with reoriented hydrides will begin this year.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Titanium and/or Aluminum Rod-Replacement Experiments in Fully-Reflected Water-Moderated Square-Pitched U(6.90)O 2 Fuel Rod Lattices with 0.67 Fuel to Water Volume Ratio (0.800 CM Pitch)

The US Department of Energy (DOE) Nuclear Energy Research Initiative funded the design and construction of the Seven Percent Critical Experiment (7uPCX) at Sandia National Laboratories. The start-up of the experiment facility and the execution of the experiments described here were funded by the DOE Nuclear Criticality Safety Program. The 7uPCX is designed to investigate critical systems with fuel for light water reactors in the enrichment range above 5% 235 U. The 7uPCX assembly is a water-moderated and -reflected array of aluminum-clad square-pitched UO2 fuel rods. The uranium is enriched to 6.90% by mass. Sets of 36 titanium and aluminum experiment rods with the same nominal outside diameter as the fuel rods were fabricated and used as replacements for fuel rods in the array. The twenty-four 7uPCX critical experiments reported here compare the effects of the titanium and aluminum replacement rods on nearly critical fuel rod arrays. The fuel used in these experiments was fabricated using unirradiated UO 2 fuel pellets from fuel elements designed to be used in the internal nuclear superheater section of the Pathfinder boiling water reactor operated in South Dakota by the Northern States Power Company in the 1960s. The fuel elements were obtained from The Pennsylvania State University where they had been stored for many years. The fuel pellets in those fuel elements were removed from the original Incoloy cladding and reclad in 3003 aluminum tubes and end caps for use in the experiments reported here. The nominal outside diameter of the fuel pellets is 0.207 in (0.52578 cm). The nominal outside diameter of the fuel rod cladding is 0.250 in (0.635 cm). The distance between the fuel rods in the square-pitched array is 0.315 in (0.8001 cm). This geometry gives a fuel-to-water volume ratio of 0.67 in the array. The twenty-four critical experiments in this series were performed in 2015 and 2016 at the Sandia Critical Experiments Facility. The first of the experiments had no replacement rods in the array and was intended to provide a baseline against which the experiments containing replacement rods could be compared. Eight critical experiments had titanium replacement rods in various numbers and arrangements near the center of the fuel array. Eight critical experiments had aluminum replacement rods in the same numbers and arrangements as in the eight experiments containing titanium experiment rods. In the final four experiments, fuel rods were removed from a central region of the array so that the pitch of the fuel rods in this part of the array was effectively doubled. This softened the neutron spectrum in the central part of the fuel array. Thirty-six replacement rods in different combinations of titanium and/or aluminum were placed in the interstices created in the center of the array. All twenty-four critical experiments are judged to be acceptable as benchmark experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Assessment of the CTF subchannel code for modeling a large-break loss-of-coolant accident reflood transient

With increased industry interest in extending reactor operating cycles, the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program has been investigating the behavior of high-burnup fuel during design basis accidents such as the large-break loss-of-coolant accident (LBLOCA) with consideration for risk of fuel fragmentation, relocation, and dispersal (FFRD). As part of that activity, the NEAMS subchannel thermal/ hydraulics (T/H) code, CTF, is being used for modeling of LBLOCA and to determine the impact of subchannel resolution on results. Although CTF includes a wide range of models for LBLOCA conditions, the code has not been used for this application while maintained at Oak Ridge National Laboratory (ORNL) until now. Therefore, here, in this work, a preliminary assessment of several of these models was performed using openly available reflood experimental data from the Flooding Experiments in Blocked Arrays (FEBA) tests. One coarse mesh and one fine mesh model were set up in CTF for high and low flooding rate tests performed in the unblocked FEBA facility. A coarse TRACE model was set up to be as consistent as possible with the coarse CTF model to allow for code-to-code benchmarking. The assessment shows a tendency of the codes to over-predict peak cladding temperature (PCT) near the top of the bundle and to quench early. Advanced spacer grid models were shown to improve upper bundle predictions in CTF. The resolved CTF model over-predicted PCT by a larger degree in the center channels in the low-flooding rate test, and it is believed that the radiative heat transfer model, which was not used in this study, may be needed to correct this over-prediction. Finally, this work demonstrates the importance of the droplet model in determining quench time and vapor temperature and PCT prediction, which necessitates a more in-depth validation of these models in the future.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Accelerated Materials Deployment in Advanced Nuclear Power Plants

The purpose of this report is to begin the development of a maximally efficient process for licensing and deploying new materials in Advanced Non-Light-Water Reactors (ANLWRs). Some new materials that are to be used in some new plants are seen as possibly introducing risks, because our understanding of those new materials’ behavior in the conditions generated by some novel plant designs is less complete than our understanding of the behavior of materials with long use histories in existing designs. In these cases, an approved code/standard or a code case to support the use of these materials in the novel design’s safety case may not exist for the regulator to utilize as part of the licensing determination. This circumstance creates the potential for an extremely long licensing process for new designs using new materials. The present strategy is to show how to manage these risks proactively, in such a way as to permit licensing decisions to be made in a timely manner, based on this risk management process. The present report outlines the gaps in the current codes to support deployment and use of novel materials and begins the development of the necessary risk management framework that is focused on the subject materials issues; it is based on risk-informed in-service surveillance practices, carried out in such a way as to compensate for current limitations in our state of knowledge. This development will enable licensing and deployment of the subject materials, conditional on the proactive surveillance process to be established. While this report is occasioned by limitations in our knowledge of certain materials issues that may arise in advanced designs, in-service surveillance is always done in order to compensate for a lack of knowledge: if we knew that components were not already failed and not trending toward failure, we would not perform surveillance, even in current-generation plants (except that prescriptive requirements would force us to do so). What is different about the surveillance program discussed here is that the issues are newer and the relevant experience base is less complete, so the surveillance presently contemplated may need to measure new things and/or measure them more often than has been traditional for surveillance coupons. The present report is devoted to the risk management framework and applies American Society of Mechanical Engineers Boiler and Pressure Vessel Code Section XI, Division [1] to establish the structure of a protocol for carrying out the necessary surveillance. These documents are generic: they do not tell us how often to surveille, or what to surveille, or what to measure, but rather how to determine those things, given certain technical inputs. The Regulatory Development R&D Program [2] is currently developing the companion supporting technical basis for the materials surveillance technology that, when completed and validated, can be used by owner/operator and NRC to implement a materials degradation management program for ANLWRs. This report also outlines salient points of discussion, positive potential outcomes, and potential concerns from industry and the USNRC. These aspects of the report intend to inform future work to develop a proposed technical process for adoption by the industry and endorsement by the USNRC to allow developers to propose a risk informed and conservative approach for the use of materials where operating experience/data and codes and standards may not exist for use of a novel material in an operating reactor environment. Additionally, such a technology could be leveraged to potentially reduce part of the upfront materials data requirements from ongoing long-term materials testing so that early action on license application could be undertaken by NRC, in parallel with the continuation of long-term data collection. This could accelerate the schedule for a first-of-a-kind ANLWR deployment or a nth-of-a-kind new materials insertion for established ANLWR designs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Suggestions on the Vapor Pressure Determination of Molten Salts

The knowledge of the thermophysical properties of coolant and fuel in molten salts nuclear reactors (MSRs), such as thermal stability and vapor pressure, are of remarkable interest, particularly for simulating safe reactor operations. Molten salt reactorsMSRs use molten salt mixtures as the primary coolant and/or fuel and are expected to operate up to 800 °C. With the revival of interest in deploying MSRs, complete thermophysical and thermochemical characterization of these materials is of interest to industry, regulators, and researchers. Vapor pressure data for molten salts are scarce in the literature, both for pure salts but especially for eutectic mixtures. This report describes the effusion method, which consist of measuring the rate of escape of vapor molecules through a small orifice for the determination of the vapor pressure of compounds and may be useful on compounds such as molten salts. Thermogravimetric analysis records the mass loss as a function of time and temperature. There are two equations that can be used to relate the mass loss rate with the vapor pressure: (1) the Knudsen equation and (2) the Langmuir equation. To apply these equations, the system needs to reach a pseudo (or near) equilibrium condition. Therefore, the experimental conditions must be such that allow the condensed and the vapor/gas phases to be in equilibrium. In order to accomplish equilibrium like conditions, the sample must be in an almost-sealed cell except for a small orifice, from where the vapor escapes. In the Knudsen method vacuum is applied to eliminate the effect that the presence of other gas molecules could have on the evaporation rate of the sample. However, Langmuir alleged that in certain conditions, such as at low temperatures and/or when the vapor pressure is low, the rate of evaporation of a substance is independent of the presence of vapor around it. For that reason, some researchers, when measuring the mass loss of a substance with a predictable low vapor pressure, do not apply vacuum when using the Langmuir equation. However, they use a standard substance to parameterize the experimental setup. The use of one equation or the other will depend on the characteristics of the sample and the availability of an appropriate standard. Some important aspects related to the nature of the samples and vapor pressure measurements are described for future consideration.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Not all Greater-Than-Class c (GTCC) waste streams are created equal - 15373

Greater-Than-Class C (GTCC) waste is a low level radioactive waste (LLRW) that exceeds the Class C concentration limits in Part 61.55 of Title 10 of the Code of Federal Regulations. Typically, this waste consists of irradiated metal components from reactors such as core shrouds, support plates, and core barrels, as well as filters and resins from reactor operations and decommissioning. Sealed sources used at hospitals, medical schools, research facilities, and universities can also be classified as GTCC waste. A third category, 'Other Waste', consisting of contaminated equipment, rubble, scrap metal, filters, soil, and solidified sludges may be classified as GTCC waste based on their differing radionuclides and concentration levels. The Low-Level Radioactive Waste Policy Amendments Act of 1985 requires the Federal Government to take responsibility for the disposal of GTCC waste. All GTCC waste created from U.S. Nuclear Regulatory Commission (NRC) licensed activities, under the Atomic Energy Act of 1954, as amended, must be disposed of in an NRC licensed facility that has been determined to be adequate to protect public health and safety. Information from Argonne National Laboratory's supplemental report on GTCC waste from 2010 anticipates that the total volume of GTCC waste will be approximately 8,800 m{sup 3} (311,000 ft{sup 3}) and the projected activity of that waste will be 5.92 x 10{sup 6} TBq (160 MCi) with generation activities ending in 2083. Currently, there is no pathway for the disposal of GTCC waste in the United States. A performance-based approach may be used to subdivide GTCC waste into various waste streams by reviewing the characteristics of GTCC waste with its associated hazards. Characteristics of GTCC waste include half-life and concentration. In creating the 10 CFR Part 61 waste classification tables, which define GTCC concentrations, a number of assumptions were made regarding waste inventory and exposure scenarios for the inadvertent intruder for a generic LLRW disposal facility. The findings from other exposure scenarios (e.g., construction, agriculture, well drilling), together with the findings from evaluations of radiological characteristics of GTCC, could be used as part of a performance-based approach for categorizing GTCC waste. The findings may determine that some GTCC waste streams will be closer in characteristics to Class C waste, while other GTCC waste streams will have characteristics similar to high-level waste and may require a higher degree of isolation from the public. The application of a site-specific and performance-based approach to GTCC waste stream characterization could assist the NRC in developing specific technical requirements for future disposal of various types of GTCC waste. Examples of part of a performance-based approach that examine and evaluate the radiological characteristics of GTCC waste will be presented. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗