Search NASA⌕ Search

SEARCH · Search NASA

Results for “Vortex flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Numerical investigation of the origin of vortex asymmetry of flows over bodies at large angle of attack

The occurrence of the flow about a slender body of revolution placed at incidence to an incoming stream is numerically examined for angles of attack ranging from 20 to 80 degrees and a Reynolds number of 200,000 based on maximum body diameter. Over a certain range of Reynolds numbers, the trend of flowfields around slender bodies at incidence can be roughly divided into three main categories: (1) at alpha = 0-30 deg, the flow is steady and symmetric; (2) at alpha = 30-60 deg, the flow under normal conditions is usually asymmetric, but the level of the asymmetry depends on the amount of disturbances present on the tip of the body; and (3) at alpha 60-90 deg, the flow in the wake of the body acts in a fashion similar to that of the Karman vortex shedding behind a two-dimensional circular cylinder. For each of these categories the range of incidence may change by + or - 10 degrees, depending on the quality of flow, or body finish.

Degani, David↗
NASA NTRS1992

Flow visualizations of perpendicular blade vortex interactions

Helium bubble flow visualizations have been performed to study perpendicular interaction of a turbulent trailing vortex and a rectangular wing in the Virginia Tech Stability Tunnel. Many combinations of vortex strength, vortex-blade separation (Z(sub s)) and blade angle of attack were studied. Photographs of representative cases are presented. A range of phenomena were observed. For Z(sub s) greater than a few percent chord the vortex is deflected as it passes the blade under the influence of the local streamline curvature and its image in the blade. Initially the interaction appears to have no influence on the core. Downstream, however, the vortex core begins to diffuse and grow, presumably as a consequence of its interaction with the blade wake. The magnitude of these effects increases with reduction in Z(sub s). For Z(sub s) near zero the form of the interaction changes and becomes dependent on the vortex strength. For lower strengths the vortex appears to split into two filaments on the leading edge of the blade, one passing on the pressure and one passing on the suction side. At higher strengths the vortex bursts in the vicinity of the leading edge. In either case the core of its remnants then rapidly diffuse with distance downstream. Increase in Reynolds number did not qualitatively affect the flow apart from decreasing the amplitude of the small low-frequency wandering motions of the vortex. Changes in wing tip geometry and boundary layer trip had very little effect.

Rife, Michael C.↗
NASA NTRS1988

Three-dimensional mean flow experimental study of 'vortex unwinding'

A seven-hole flow-angularity pressure probe was used to assess the effectiveness of vortex unwinding in a turbulent boundary layer. The vortex center moved in the spanwise and vertical direction with increasing longitudinal distance. Initially, the vortex moved rapidly; it achieved 60 percent of its total 41 mm spanwise travel before it had completed half of its travel in the longitudinal direction. The flow was studied behind the single vortex combined with the most successful unwinder. The unwinder was found to be very effective in reducing the amount of secondary flow in the boundary layer.

Mcginley, Catherine B.↗
NASA NTRS1984

Flow visualization study of a vortex-wing interaction

A flow visualization study in water was completed on the interaction of a streamwise vortex with a laminar boundary layer on a two-dimensional wing. The vortex was generated at the tip of a finite wing at incidence, mounted perpendicular to the main wing, and having the same chord as the main wing. The Reynolds number based on wing chord was about 5000. Two different visualization techniques were used. One involved the injection of two different colored dyes into the vortex and the boundary layer. The other technique utilized hydrogen bubbles as an indicator. The position of the vortex was varied in a directional normal to the wing. The angle of attack of the main wing was varied from -5 to +12.5 deg. The vortex induced noticeable cross flows in the wing boundary layer from a distance equivalent to 0.75 chords. When very close to the wing, the vortex entrained boundary layer fluid and caused a cross flow separation which resulted in a secondary vortex.

Mehta, R. D.↗
NASA NTRS1974

An experimental and theoretical study of the flow phenomena within a vortex sink rate sensor

Tests were conducted to obtain a description of the flow field within a vortex sink rate sensor and to observe the influence of viscous effects on its performance. The characteristics of the sensor are described. The method for conducting the test is reported. It was determined that for a specific mass flow rate and the geometry of the vortex chamber, the flow in the vortex chamber was only affected, locally, by the size of the sink tube diameter. Within the sink tube, all three velocity components were found to be higher for the small sink tube diameters. As the speed of rotation of the sensor was increased, the tangential velocities within the vortex chamber, as well as in the sink tube, increased in proportion to the speed of rotation.

Goglia, G. L.↗
DOE OSTI2021

The effect of entrance flow development on vortex formation and wall shear stress in a curved artery model

In this work, we numerically investigate the effect of entrance condition on the spatial and temporal evolution of multiple three-dimensional vortex pairs and the wall shear stress distribution in a curved artery model. We perform this study using a Newtonian blood-analog fluid subjected to a pulsatile flow with two inflow conditions. The first flow condition is fully developed while the second condition is undeveloped (i.e., uniform). We discuss the connection along the axial direction between regions of organized vorticity observed at various cross sections of the model and compare results between the different entrance conditions. We model a human artery with a simple, rigid 180° curved pipe with a circular cross section and constant curvature, neglecting the effects of taper, torsion, and elasticity. Numerical results are computed from a discontinuous high-order spectral element flow solver. The flow rate used in this study is physiological. We observe differences in secondary flow patterns, especially during the deceleration phase of the physiological waveform where multiple vortical structures of both Dean-type and Lyne-type coexist. The results indicate that decreased axial velocities under an undeveloped condition produce smaller secondary flows that ultimately inhibit growth of any interior flow vortices. We highlight the effect of the entrance condition on the formation of these structures and subsequent appearance of abnormal inner wall shear stresses, which suggest there may be a lower prevalence of cardiovascular disease in curved arteries where the flow is rather undeveloped—a potentially physiologically significant result to help understand the influence of blood flow development on disease.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1986

Application of a computational model for vortex generators in subsonic internal flows

A model for the analysis of vortex generators in a fully viscous subsonic internal flow is evaluated. A vorticity source term is used in a modified form of the Parabolized Navier-Stokes equations to model the shed vortex. Computed results are compared with idealized flow vortex paths, and with experimental data for vortex generators embedded in a thick turbulent boundary layer. The analysis is also compared with experimental data for a separated diffusing S-duct and for a diffusing S-duct with vortex generators. Quantitative comparisons are shown for the latter three cases. Emphasis is placed on verifying the ability of the model to predict global distortions in the flow field.

Kunik, W. G.↗
NASA NTRS1986

Application of a computational model for vortex generators in subsonic internal flows

A model for the analysis of vortex generators in a fully viscous subsonic internal flow is evaluated. A vorticity source term is used in a modified form of the Parabolized Navier-Stokes equations to model the shed vortex. Computed results are compared with idealized flow vortex paths, and with experimental data for vortex generators embedded in a thick turbulent boundary layer. The analysis is also compared with experimental data for a separated diffusing S-duct and for a diffusing S-duct with vortex generators. Quantitative comparisons are shown for the latter three cases. Emphasis is placed on verifying the ability of the model to predict global distortions in the flow field.

Kunik, W. G.↗
NASA NTRS1974

An experimental and theoretical study of the flow phenomena within a vortex sink rate sensor

A description of the flow field within a vortex sink rate sensor was obtained, and the influence of viscous effects on its performance was observed. The sensor basically consisted of a vortex chamber and a sink tube. The vortex chamber consisted of two circular coaxial disks held apart, at their periphery, by a porous coupling. One circular disk had an opening to permit the mounting of the sink tube, in such a manner that the vortex chamber as well as the sink tube had a common axis of rotation. Air was supplied radially to the sensor through its porous coupling as the sensor was rotated at various speeds. Particular emphasis was directed toward an understanding of the flow field in the sink tube region. Thus velocity measurements at various stations along the length of the sink tube as well as along a given radius at any designated station were taken.

Patel, D. K.↗
NASA NTRS1979

Evaluation of a vortex model of turbulent cavity flow

A two dimensional discrete vortex model is applied to turbulent flow over a cavity at a Reynolds number based on cavity half length of approximately 500,000. These model predictions are compared with experimental data on a time average and on a spectral basis. The comparisons indicate that the vortex model reproduces the mean velocity profiles of this complex flow, while the turbulent intensity and Reynolds stress profiles are overpredicted in magnitude. Spectral analyses show that the vortex model introduces unrealistic low frequency power which becomes less dominant as the model becomes more disordered. The spectral power distribution of the model in this state is nearly in agreement with that of the data, somewhat too low at the higher frequencies and too high at the lower frequencies. The model is shown to be capable of reproducing the cavity feedback oscillation phenomenon.

Hardin, J. C.↗
NASA NTRS1981

Computation of wing-vortex interaction in transonic flow using implicit finite difference algorithm

An implicit delta form finite difference algorithm for Euler equations in conservation law form was used in preliminary calculations of three dimensional wing vortex interaction. Both steady and unsteady transonic flow wing vortex interactions are computed. The computations themselves are meant to guide upcoming wind tunnel experiments of the same flow field. Various modifications to the numerical method that are intended to improve computational efficiency are also described and tested in both two and three dimensions. Combination of these methods can reduce the overall computational time by a factor of 4.

Srinivasan, G.↗
NASA NTRS1980

Vortex methods for two- and three-dimensional flow simulations

The point vortex and vortex blob methods for two dimensional flows are presented. Several results are discussed concerning the numerical analysis of the latter scheme, e.g., the preservation of globally conserved quantities and the analysis of the spatial discretization error resulting from the convection of fixed blobs of vorticity. An application to the two dimensional mixing layer is briefly described. The contour dynamics method is also discussed. The simulation of three dimensional flows with vortex methods is discussed. A natural way to represent the vorticity is in the form of closed tubes of filaments of vorticity, although other schemes are examined. Applications to aircraft trailing vortices and to a turbulent spot in a laminar boundary layer are presented. Hybrid schemes that use an Eulerian mesh to solve the Poisson equation for the velocity field are discussed. The goal of these schemes is to avoid the high cost of the Biot-Savart integration if many vortex elements are used while enjoying most of the advantages of pure Lagrangian schemes.

Leonard, A.↗
NASA NTRS1987

Motion and decay of vortex rings submerged in a rotational flow

The interaction between vortex rings of finite strength and an axisymmetric rotational background flow is studied by a singular perturbation method, because it is difficult to use a finite-difference method to analyze the viscous decay in the small core of a vortex ring. The analysis is carried out by combining a composite solution of a vortex ring and an unsteady Euler solution for the background rotational flow. Using the method of averaging, a numerical scheme is developed to obtain an Euler solution in which the grid and time-step sizes depend solely on the length and velocity scales of the background flow. Numerical results are presented to illustrate the interaction between the trajectories and decay rates of the vortex rings and the background rotational flow.

Ishii, K.↗
NASA NTRS1990

Schlieren System For Flow Studies In Round Glass Pipes

In schlieren system for studying flow of gas in transparent pipe of circular cross section, cylindrical lenses placed on opposite sides of pipe compensate for refraction caused by wall of pipe. Enables direct visualization of such phenomena as laminar or turbulent flow, shock waves, vortexes, and flow separations in systems having inherently cylindrical geometry; potentially unreliable extrapolations from results in flat-sided test cells no longer necessary.

Costen, Robert C.↗
NASA NTRS1998

Self-Similar Compressible Free Vortices

Lie group methods are used to find both exact and numerical similarity solutions for compressible perturbations to all incompressible, two-dimensional, axisymmetric vortex reference flow. The reference flow vorticity satisfies an eigenvalue problem for which the solutions are a set of two-dimensional, self-similar, incompressible vortices. These solutions are augmented by deriving a conserved quantity for each eigenvalue, and identifying a Lie group which leaves the reference flow equations invariant. The partial differential equations governing the compressible perturbations to these reference flows are also invariant under the action of the same group. The similarity variables found with this group are used to determine the decay rates of the velocities and thermodynamic variables in the self-similar flows, and to reduce the governing partial differential equations to a set of ordinary differential equations. The ODE's are solved analytically and numerically for a Taylor vortex reference flow, and numerically for an Oseen vortex reference flow. The solutions are used to examine the dependencies of the temperature, density, entropy, dissipation and radial velocity on the Prandtl number. Also, experimental data on compressible free vortex flow are compared to the analytical results, the evolution of vortices from initial states which are not self-similar is discussed, and the energy transfer in a slightly-compressible vortex is considered.

vonEllenrieder, Karl↗
NASA NTRS1989

Vortex-dominated conical-flow computations using unstructured adaptively-refined meshes

A conical Euler/Navier-Stokes algorithm is presented for the computation of vortex-dominated flows. The flow solver involves a multistage Runge-Kutta time stepping scheme which uses a finite-volume spatial discretization on an unstructured grid made up of triangles. The algorithm also employs an adaptive mesh refinement procedure which enriches the mesh locally to more accurately resolve the vortical flow features. Results are presented for several highly-swept delta wing and circular cone cases at high angles of attack and at supersonic freestream flow conditions. Accurate solutions were obtained more efficiently when adaptive mesh refinement was used in contrast with refining the grid globally. The paper presents descriptions of the conical Euler/Navier-Stokes flow solver and adaptive mesh refinement procedures along with results which demonstrate the capability.

Batina, John T.↗