Results for “core processes” — Page 34

NASA NTRS2019

Scaling Evaluation of Ice-Crystal Icing on a Modern Turbofan Engine in PSL Using the COMDES-MELT Code

This paper presents preliminary ice-crystal icing (ICI) altitude scaling evaluation results of a Honeywell Uncertified Research Engine (HURE) that was tested in the NASA Glenn Research Center Propulsion Systems Laboratory (PSL) during January of 2018. This engine geometry features a hidden core design to keep the core less exposed. The engine was fitted with internal video cameras to observe various ice buildup processes at multiple selected locations within the engine core flow path covering the fan stator, the splitter-lip/shroud/strut, and the high pressure compressor (HPC) variable inlet guide vane (IGV) regions. The potential ice accretion risk was pre-determined to occur by using NASA’s in-house 1D Engine Icing Risk assessment code, COMDES-MELT. The code was successful in predicting the risk of ice accretion in adiabatic regions like the fan-stator of the HURE at specific engine operating points. However at several operating points during the test, liquid water was observed running along the shroud toward the variable IGV of the HPC regions with an air temperature well below freezing, thus no particle melting could have occurred due to heating from the air alone. It was reasoned that other sources of heat were present in that region. To account for these heat sources the inlet total temperature was adjusted to give a wet bulb temperature of 24 F below the standard minimum wet bulb temperature of 492 R to allow ice to accrete in the splitter-lip/shroud/strut region, which was determined from a reference case where hard ice was observed in that region. With that adjustment the COMDES-MELT code was successful in providing operating points where there was a risk of ice accretion during the test campaign. In addition to calculating possible conditions at different selected lower altitudes, simulations were run to determine potential inlet conditions that could lead to ice-crystal accretion along the prescribed stations where the cameras were available. From there, scaled test conditions were determined by best matching the following three icing related parameters of the reference condition: (1) the local air total wet bulb temperature, (2) the local ice crystal cloud melt ratio and (3) the engine fan face ice/water to air mass flux ratio of the ice crystal cloud. Instantaneous images taken from the time-lapsed movies of ice buildup were used along with the relevant thermodynamic data of air, water vapor and local icing condition to help evaluate how closely the proposed altitude scaling method could be used in ground based test facility to duplicate selected reference ICI features observed at specific location inside this engine at different scale altitudes. Discussions on observed limitation for engine icing scaling application from this test campaign and needed improvement are provided. A scaling test procedure to help identify potential ICI risk conditions and possible ice accretion locations of a new turbofan engine is evaluated in PSL.

Engine Testing in PSL↗

NASA NTRS2014

A Numerical and Experimental Study of Damage Growth in a Composite Laminate

The present study has three goals: (1) perform an experiment where a simple laminate damage process can be characterized in high detail; (2) evaluate the performance of existing commercially available laminate damage simulation tools by modeling the experiment; (3) observe and understand the underlying physics of damage in a composite honeycomb sandwich structure subjected to low-velocity impact. A quasi-static indentation experiment has been devised to provide detailed information about a simple mixed-mode damage growth process. The test specimens consist of an aluminum honeycomb core with a cross-ply laminate facesheet supported on a stiff uniform surface. When the sample is subjected to an indentation load, the honeycomb core provides support to the facesheet resulting in a gradual and stable damage growth process in the skin. This enables real time observation as a matrix crack forms, propagates through a ply, and then causes a delamination. Finite element analyses were conducted in ABAQUS/Explicit(TradeMark) 6.13 that used continuum and cohesive modeling techniques to simulate facesheet damage and a geometric and material nonlinear model to simulate core crushing. The high fidelity of the experimental data allows a detailed investigation and discussion of the accuracy of each numerical modeling approach.

McElroy, Mark↗

NASA NTRS2014

TPSAS-NF1676L-19616-DND

The present study has three goals: (1) perform an experiment where a simple laminate damage process can be characterized in high detail; (2) evaluate the performance of existing commercially available laminate damage simulation tools by modeling the experiment; (3) observe and understand the underlying physics of damage in a composite honeycomb sandwich structure subjected to low-velocity impact. A quasi-static indentation experiment has been devised to provide detailed information about a simple mixed-mode damage growth process. The test specimens consist of an aluminum honeycomb core with a cross-ply laminate facesheet supported on a stiff uniform surface. When the sample is subjected to an indentation load, the honeycomb core provides support to the facesheet resulting in a gradual and stable damage growth process in the skin. This enables real time observation as a matrix crack forms, propagates through a ply, and then causes a delamination. Finite element analyses were conducted in ABAQUS/Explicit(TradeMark) 6.13 that used continuum and cohesive modeling techniques to simulate facesheet damage and a geometric and material nonlinear model to simulate core crushing. The high fidelity of the experimental data allows a detailed investigation and discussion of the accuracy of each numerical modeling approach.

Mark McElroy↗

NASA NTRSDate not supplied

Determining Surface Exposure Ages of Regolith Grains in Lunar Core Sample 73002 By Investigating Solar Particle Irradiation Damage

Space weathering causes the surface soils of airless bodies like the Moon to be micro-structurally and chemically altered by exposure to micrometeoroid bombardment and solar wind irradiation. These alterations accumulate in surface grains with continued residence in the uppermost millimeters of regolith. Low energy solar wind ions (largely H+ and He+) produce a layer of radiation damage as they become implanted in grain surfaces. Also present are solar energetic particle (SEP) tracks, which are nanoscale lineations within grain interiors formed by heavy, high-energy ions (mainly Fe group nuclei) penetrating up to millimeters below the surface. Recent work has determined that the width of solar wind-damaged rims on anorthite and olivine, and their respective SEP track densities are correlated with each other and with grain surface exposure age. Core sample 73002, recently released under the Apollo Next Generation Sample Analysis (ANGSA) Program, has provided an opportunity to study material collected from the light mantle formation in the Taurus-Littrow Valley during Apollo 17. The light mantle is thought to have been deposited vial and slide originating from the neighboring South Massif. Spectral analysis of bulk core soils found a plagioclase rich composition, confirming a highlands origin of the formation. Spectral profiles and ferromagnetic resonance (FMR) measurements of bulk soils sampled at cm-intervals from 73002 indicate that regolith up to~9.5 cm in depth have maturity indices consistent with longer durations of surface processing than samples deeper in the core. Thus, this upper ~9 cm layer likely represents the maximum extent of an in-situ reworking zone which may have persisted over 5 to 17million years. Here we present an analysis of grain exposure ages within the in-situ reworking zone of 73002derived from SEP track density measurements via transmission electron microscopy.

J A McFadden↗

DOE OSTI2023

Structure of the T. brucei kinetoplastid RNA editing substrate-binding complex core component, RESC5

Kinetoplastid protists such as Trypanosoma brucei undergo an unusual process of mitochondrial uridine (U) insertion and deletion editing termed kinetoplastid RNA editing (kRNA editing). This extensive form of editing, which is mediated by guide RNAs (gRNAs), can involve the insertion of hundreds of Us and deletion of tens of Us to form a functional mitochondrial mRNA transcript. kRNA editing is catalyzed by the 20 S editosome/RECC. However, gRNA directed, processive editing requires the RNA editing substrate binding complex (RESC), which is comprised of 6 core proteins, RESC1-RESC6. To date there are no structures of RESC proteins or complexes and because RESC proteins show no homology to proteins of known structure, their molecular architecture remains unknown. RESC5 is a key core component in forming the foundation of the RESC complex. To gain insight into the RESC5 protein we performed biochemical and structural studies. We show that RESC5 is monomeric and we report the T . brucei RESC5 crystal structure to 1.95 Å. RESC5 harbors a dimethylarginine dimethylaminohydrolase-like (DDAH) fold. DDAH enzymes hydrolyze methylated arginine residues produced during protein degradation. However, RESC5 is missing two key catalytic DDAH residues and does bind DDAH substrate or product. Implications of the fold for RESC5 function are discussed. This structure provides the first structural view of an RESC protein.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2024

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Morphology-controlled transformation of Cu@Au core-shell nanowires into thermally stable Cu 3 Au intermetallic nanowires

Multimetallic nanowires with long-range atomic ordering hold the promise of unique physicochemical properties in many applications. Here we demonstrate the synthesis and study the stability of Cu 3 Au intermetallic nanowires. The synthesis is achieved by using Cu@Au core-shell nanowires as precursors. With appropriate Cu/Au stoichiometry, the Cu@Au core-shell nanowires are transformed into fully ordered Cu 3 Au nanowires under thermal annealing. Thermally-driven atom diffusion accounts for this transformation as revealed by X-ray diffraction and electron microscopy studies. The twin boundaries abundant in the Cu@Au core-shell nanowires facilitate the ordering process. The resulting Cu 3 Au intermetallic nanowires have uniform and accurate atomic positioning in the crystal lattice, which enhances the nobility of Cu. No obvious copper oxides are observed in fully ordered Cu 3 Au nanowires after annealing in air at 200 °C, a temperature that is much higher than those observed in Cu@Au core-shell and pure Cu nanowires. This work opens up an opportunity for further research into the development and applications of intermetallic nanowires.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2023

Computationally Guided Design of Multiple Impurities Tolerant Electrode (Final Report)

The current project was based on a combined experimental and computational approach, which can help recommend better cathode materials under multiple impurities conditions. The PI will mainly take in charge of experimental and computational thermodynamics of the selected cathode materials for the SOFC applications under multiple impurities. While the co-PI will run the electrochemical tests of the cathodes recommended and eventually the long-term degradation tests. At the end of the project, a multiple tolerant cathode material based on the combined experimental and computational approach will be recommended and the reliability of the commonly used accelerated testing will be evaluated. It will address multiple impurities poisoning effect of SO2, CO2, Cr and H2O on the LSM, LSCF and LNO cathodes by identifying the formation of the detrimental secondary phases by XRD, SEM and TEM techniques. And further recommended cathode material will be subjected to electrochemical testing and the most promising ones will be applied to long-term tests. The hybrid approach the PI proposed will not only be applied to the design of multiple impurities tolerant cathodes but will also be considered in the future oxygen electrode applications in SOECs or reversible SOCs. This hybrid computational and experimental approach includes four sections: 1) Investigation of single impurity poisoning on LSM, LSCF and LNO cathodes in the presence of SO2, CO2, Cr. In this section, LSM, LSCF cathodes from FuelCellMaterials and LNO cathodes from Sol-Gel synthesis will be heat-treated in the above single impurity. And the formation of the secondary phases as well as the corresponding simulations will be cross compared, which shows good agreement between each other. Meanwhile, the accelerated testing approach will be evaluated in these systems compared with the previous published work to understand the reliability of the approach. 2) Investigation of multiple impurities poisoning on LSM, LSCF and LNO cathodes in the presence of Cr+H2O, SO2+Cr and SO2+Cr+H2O conditions. We have also applied these 3 candidate cathodes under these multiple impurities’ conditions and the long-term degradation mechanism of the multiple impurities will be understood with the help of the combined experimental and computational approach. Meanwhile, the synergistic effect of those impurities will be compared with the individual ones in the same cathode system to further reveal the actual operating conditions. 3) Electrochemical testing and polarization of the recommended cathode. We have demonstrated very low polarization resistance in LSCF (core)-LSM (shell) electrodes using MSD process and analyzed impedance spectra using DRT analysis and confirming that the low polarization resistance in LSM infiltrated MSD cells is due to reduction in polarization resistance associated with O2-adsorption process. 4). Long-term degradation testing. We have developed a versatile MSD-based process to deposit various continuous coatings onto porous scaffolds and established baseline for longer term Cr-impurity testing in future projects.

36 MATERIALS SCIENCE↗

NASA NTRS2015

AMO EXPRESS: A Command and Control Experiment for Crew Autonomy Onboard the International Space Station

NASA is investigating a range of future human spaceflight missions, including both Mars-distance and Near Earth Object (NEO) targets. Of significant importance for these missions is the balance between crew autonomy and vehicle automation. As distance from Earth results in increasing communication delays, future crews need both the capability and authority to independently make decisions. However, small crews cannot take on all functions performed by ground today, and so vehicles must be more automated to reduce the crew workload for such missions. NASA's Advanced Exploration Systems Program funded Autonomous Mission Operations (AMO) project conducted an autonomous command and control experiment on-board the International Space Station that demonstrated single action intelligent procedures for crew command and control. The target problem was to enable crew initialization of a facility class rack with power and thermal interfaces, and involving core and payload command and telemetry processing, without support from ground controllers. This autonomous operations capability is enabling in scenarios such as initialization of a medical facility to respond to a crew medical emergency, and representative of other spacecraft autonomy challenges. The experiment was conducted using the Expedite the Processing of Experiments for Space Station (EXPRESS) rack 7, which was located in the Port 2 location within the U.S Laboratory onboard the International Space Station (ISS). Activation and deactivation of this facility is time consuming and operationally intensive, requiring coordination of three flight control positions, 47 nominal steps, 57 commands, 276 telemetry checks, and coordination of multiple ISS systems (both core and payload). Utilization of Draper Laboratory's Timeliner software, deployed on-board the ISS within the Command and Control (C&C) computers and the Payload computers, allowed development of the automated procedures specific to ISS without having to certify and employ novel software for procedure development and execution. The procedures contained the ground procedure logic and actions as possible to include fault detection and recovery capabilities.

Stetson, Howard K.↗

NASA NTRS2015

AMO EXPRESS: A Command and Control Experiment for Crew Autonomy Onboard the International Space Station

NASA is investigating a range of future human spaceflight missions, including both Mars-distance and Near Earth Object (NEO) targets. Of significant importance for these missions is the balance between crew autonomy and vehicle automation. As distance from Earth results in increasing communication delays, future crews need both the capability and authority to independently make decisions. However, small crews cannot take on all functions performed by ground today, and so vehicles must be more automated to reduce the crew workload for such missions. NASA's Advanced Exploration Systems Program funded Autonomous Mission Operations (AMO) project conducted an autonomous command and control experiment on-board the International Space Station that demonstrated single action intelligent procedures for crew command and control. The target problem was to enable crew initialization of a facility class rack with power and thermal interfaces, and involving core and payload command and telemetry processing, without support from ground controllers. This autonomous operations capability is enabling in scenarios such as initialization of a medical facility to respond to a crew medical emergency, and representative of other spacecraft autonomy challenges. The experiment was conducted using the Expedite the Processing of Experiments for Space Station (EXPRESS) rack 7, which was located in the Port 2 location within the U.S Laboratory onboard the International Space Station (ISS). Activation and deactivation of this facility is time consuming and operationally intensive, requiring coordination of three flight control positions, 47 nominal steps, 57 commands, 276 telemetry checks, and coordination of multiple ISS systems (both core and payload). Utilization of Draper Laboratory's Timeliner software, deployed on-board the ISS within the Command and Control (C&C) computers and the Payload computers, allowed development of the automated procedures specific to ISS without having to certify and employ novel software for procedure development and execution. The procedures contained the ground procedure logic and actions as possible to include fault detection and recovery capabilities. The autonomous operations concept includes a reduction of the amount of data a crew operator is required to verify during activation or de-activation, as well as integration of procedure execution status and relevant data in a single integrated display. During execution, the auto-procedures (via Timerliner) provide a step-by-step messaging paradigm and a high-level status upon termination. This messaging and high-level status is the only data generated for operator display. To enhance situational awareness of the operator, the Web-based Procedure Display (WebPD) provides a novel approach to the issues of procedure display and execution tracking. WebPD is a web based application that serves as the user interface for electronic procedure execution. It incorporates several aspects of the HTML5 standard. Procedures are written in a dialect of XML called Procedure Representation Language (PRL). WebPD tracks execution status in the procedure or procedures being displayed. WebPD aggregates and simplifies the auto-sequence execution status information, and formatted to be easily followed and understood by an operator who is not dedicated to actively monitoring the task. WebPD also provides an integrated data and control interface to pause or halt the execution in order to provide a check point of operation and to examine progress before starting the next sequence of activities. For this demonstration, the procedure was initiated and monitored from the ground. As the Timeliner sequences executed, their high-level execution status was written to PLMDM memory. This memory is read and downlinked via Ku-Band at a 1 Hz rate. The data containing the high-level execution status is de-commutated on the ground, and rebroadcast for WebPD consumption. A future demonstration will be performed onboard, with ISS astronauts initiating the operations instead of ground controllers. The AMO EXPRESS experiment demonstrated activation and de-activation of EXPRESS rack 7, providing the capability of future single button activations and deactivations of facility class racks. The experiment achieved numerous technical and operations 'firsts' for the ISS

Stetson, Howard K.↗

NASA NTRS2015

AMO EXPRESS: A Command and Control Experiment for Crew Autonomy

NASA is investigating a range of future human spaceflight missions, including both Mars-distance and Near Earth Object (NEO) targets. Of significant importance for these missions is the balance between crew autonomy and vehicle automation. As distance from Earth results in increasing communication delays, future crews need both the capability and authority to independently make decisions. However, small crews cannot take on all functions performed by ground today, and so vehicles must be more automated to reduce the crew workload for such missions. NASA's Advanced Exploration Systems Program funded Autonomous Mission Operations (AMO) project conducted an autonomous command and control demonstration of intelligent procedures to automatically initialize a rack onboard the International Space Station (ISS) with power and thermal interfaces, and involving core and payload command and telemetry processing, without support from ground controllers. This autonomous operations capability is enabling in scenarios such as a crew medical emergency, and representative of other spacecraft autonomy challenges. The experiment was conducted using the Expedite the Processing of Experiments for Space Station (EXPRESS) rack 7, which was located in the Port 2 location within the U.S Laboratory onboard the International Space Station (ISS). Activation and deactivation of this facility is time consuming and operationally intensive, requiring coordination of three flight control positions, 47 nominal steps, 57 commands, 276 telemetry checks, and coordination of multiple ISS systems (both core and payload). The autonomous operations concept includes a reduction of the amount of data a crew operator is required to verify during activation or de-activation, as well as integration of procedure execution status and relevant data in a single integrated display. During execution, the auto-procedures provide a step-by-step messaging paradigm and a high level status upon termination. This messaging and high level status is the only data generated for operator display. To enhance situational awareness of the operator, the Web-based Procedure Display (WebPD) provides a novel approach to the issues of procedure display and execution tracking. For this demonstration, the procedure was initiated and monitored from the ground. As the Timeliner sequences executed, their high level execution status was transmitted to ground, for WebPD consumption.

Stetson, Howard K.↗

NASA NTRS1978

Gaseous fuel reactors for power systems

The Los Alamos Scientific Laboratory is participating in a NASA-sponsored program to demonstrate the feasibility of a gaseous uranium fueled reactor. The work is aimed at acquiring experimental and theoretical information for the design of a prototype plasma core reactor which will test heat removal by optical radiation. The basic goal of this work is for space applications, however, other NASA-sponsored work suggests several attractive applications to help meet earth-bound energy needs. Such potential benefits are: small critical mass, on-site fuel processing, high fuel burnup, low fission fragment inventory in reactor core, high temperature for process heat, optical radiation for photochemistry and space power transmission, and high temperature for advanced propulsion systems.

Helmick, H. H.↗

DOE OSTI2018

Development of Preliminary VERA-CS Crud Induced Localized Corrosion Modeling Capability

The objective of this milestone was to develop a crud-induced localized corrosion (CILC) screening capability in VERA-CS using existing codes and capabilities that had been developed in the Consortium for Advanced Simulation of Light Water Reactors (CASL) as part of the efforts to resolve the crud challenge problem. The milestone work focused on improving existing CASL software and implementing clad corrosion modeling into VERA-CS. Clad corrosion modeling was implemented by creating an application interface (API) in the Cicada software so that its clad heat transfer and corrosion models could be used in VERA-CS. Cicada was coupled to the subchannel code CTF for solving crud and corrosion growth. Additionally, a clad corrosion model was added directly to CTF to serve as an alternate approach. The rod thermal hydraulic reconstruction (ROTHCON) process, which is used for capturing computational fluid dynamics (CFD)-predicted rod-surface heat and turbulence behavior that can impact crud-induced power shift (CIPS) and CILC prediction, was also implemented into VERA-CS. Usability improvements were made to this feature, which was developed over several previous milestones, so that the VERA-CS user can link spacer grids in a VERA-CS model to an applicable pregenerated spacer grid data file if available. Several assessments were performed to demonstrate the proper functioning of the new capability. Sensitivity studies were performed to demonstrate the effect of crud lithium content, oxide thermal conductivity, Cicada mesh refinement, and ROTHCON coupling mesh refinement on predicted amounts of crud and oxide growth. A full-scale demonstration was performed by running Seabrook Cycle 5 with the CILC capability. Some general observations were made from the assessments. It was observed that predicted corrosion thickness is less than anticipated for CILC cases, so further work is needed to better understand and improve the corrosion modeling. Refining the coupling mesh in the ROTHCON process leads to increased corrosion and crud thickness, which can affect where crud and corrosion grow, how thick it gets, and how many rods experience crud and corrosion growth. Results indicate that applying the ROTHCON process and refining the coupling mesh leads to only a slight increase in total core maximum crud and corrosion thickness, but it leads to a significant increase in the number of rods with a maximum thickness that surpasses a set threshold value (i.e., more rods grow thicker corrosion and crud). Computational performance of the simulation is degraded by a factor of 5{6 with high coupling mesh refinement. The impact of the ROTHCON coupling mesh refinement on total core crud mass is less significant; however, using the ROTHCON process with CFD-generated data over the Yao{Hochreiter{Leech (YHL) model in CTF leads to significantly different amounts of total core crud mass. Future work on the CILC screening capability will include model improvement and validation, development and testing of a CILC-risk screening criteria, and performance improvements.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1992

Space Station Furnace Facility. Volume 1: Requirements definition and conceptual design study, executive summary

The Space Station Freedom Furnace (SSFF) Study was awarded on June 2, 1989, to Teledyne Brown Engineering (TBE) to define an advanced facility for materials research in the microgravity environment of Space Station Freedom (SSF). The SSFF will be designed for research in the solidification of metals and alloys, the crystal growth of electronic and electro-optical materials, and research in glasses and ceramics. The SSFF is one of the first 'facility' class payloads planned by the Microgravity Science and Applications Division (MSAD) of the Office of Space Science and Applications of NASA Headquarters. This facility is planned for early deployment during man-tended operations of the SSF with continuing operations through the Permanently Manned Configuration (PMC). The SSFF will be built around a general 'Core' facility which provides common support functions not provided by SSF, common subsystems which are best centralized, and common subsystems which are best distributed with each experiment module. The intent of the facility approach is to reduce the overall cost associated with implementing and operating a variety of experiments. This is achieved by reducing the launch mass and simplifying the hardware development and qualification processes associated with each experiment. The Core will remain on orbit and will require only periodic maintenance and upgrading while new Furnace Modules, samples, and consumables are developed, qualified, and transported to the SSF. The SSFF Study was divided into two phases: phase 1, a definition study phase, and phase 2, a design and development phase. The definition phase 1 is addressed. Phase 1 was divided into two parts. In the first part, the basic part of the effort, covered the preliminary definition and assessment of requirements; conceptual design of the SSFF; fabrication of mockups; and the preparation for and support of the Conceptual Design Review (CoDR). The second part, the option part, covered requirements update and documentation; refinement of the selected conceptual design through additional trades and analyses; design, fabrication, and test of the Development Model; and design, fabrication, and test of the Interrack Demonstration Unit; and support of the requirements definition review (RDR). The purpose of part 2 was to prove concept feasibility.

Source record↗

NASA NTRS2021

Characterization Study of TestBed Infrastructure Performance in a Distributed Simulation Environment: Baseline Analysis

Characterization of the performance of Air Traffic Management Exploration (ATM-X) TestBed integration environment has been investigated and documented for one system configuration for progressively increasing traffic. Several statistical parameters were used to assess the performance of the TestBed distributed system such as mean, standard deviation, skewness, and kurtosis of latency, and update rate for aircraft state messages that are transmitted through the simulated system under investigation. It is necessary to assess the performance characteristics of distributed systems in terms of the indicated statistical parameters mentioned above. It is critical to verify the system performance with respect to a researcher’s required system performance. Computer host specifications are documented in terms of Central Processing Unit (CPU) clock speed and core count. Transmission Control Protocol/ Internet Protocol (TCP/IP) message protocol was used for data transmission. The system network topology also contributes to the latency and update rate variations from the one imposed by the data source. The motivation for selecting the TestBed infrastructure as the focus of this study can be attributed to the number of services and capabilities it provides that help simplify the process of preparing and conducting a simulation. These capabilities include an easy to use GUI for simulation configuration, access to TestBed library by the end-user of other simulation software components, a modular adapter paradigm that allows simple connectivity of external software to TestBed, connectivity with other simulation laboratories, and a Software Development Kit (SDK) for quicker development. Two types of traffic generators, Air Traffic Generator (ATG) and Multi Aircraft Control System (MACS) were used to generate messages that were injected into the TestBed distributed environment. Eight different air traffic scenarios with progressively increasing loads were generated for each air traffic simulator. The corresponding air traffic loads between the two simulators had an identical number of aircraft per scenario, but different flight plans. It was observed that the performance of MACS degraded for air traffic scenarios containing more than 200 aircraft (37.5 KB/s nominal throughput). However, ATG performed adequately under all tested air traffic loads up to 1200 aircraft (225. KB/s nominal throughput). The tests show that MACS exhibits better latency performance with smaller aircraft loads when compared to ATG. The tests also show that the TestBed infrastructure successfully transmits 1200 aircraft without significant degradation of its performance. From the latency trends for both MACS and ATG, it is clear that as aircraft load increases, the latency in the system increases as well as its standard deviation. Likewise, the trends for the update data rate for both MACS and ATG show that as the aircraft load increases, so does the standard deviation and mean of the update rates which can be attributed to the performance of MACS and ATG applications. The analysis of the results of this study have proven that the overall system performance is dependent on the individual performance of each system component that is connected to TestBed, which subsequently propagates into the system. All TestBed characterization tests were conducted in SimLabs at NASA Ames Research Center in November 2019. This study addresses the need for a baseline TestBed characterization, and the results will serve as a reference for more complex simulation systems.

Air Traffic Management simulations↗

DOE OSTI2020

Transition Core Analysis for HEU to LEU Fuel Conversion at the University of Missouri Research Reactor

A new type of low-enriched uranium (LEU) fuel based on an alloy of uranium and molybdenum is expected to allow the conversion of U.S. domestic high-performance research and test reactors requiring high density fuel from highly enriched uranium (HEU) to LEU. The University of Missouri Research Reactor (MURR (R)) has undergone design and performance calculations for conversion to this LEU fuel. Presented in this paper is the analysis of a crucial step in the conversion process: the sequence of MURR transition cores from all fresh to equilibrium burnup LEU operations. During the initial conversion from HEU to LEU fuel, MURR will operate atypically due to the lack of burned LEU elements. Given the constraints of MURR operation and experiments, a proposed transition scheme minimizes the time MURR operates atypically compared to the prototypic cycles currently run with HEU fuel and moves quickly to the same sort of equilibrium cycles for the LEU fuel.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS1993

EOS ground data systems: A description and interface overview

The Earth Observing System (EOS) is planned as a space-based measurement system, earth-science research program, and data and information system (EOSDIS). It will consist of several high data rate spacecraft with multiple earth sensing instruments which provide investigators with a thorough, longterm view of the earth's environment. Up to seven spacecraft may be supported at once, either in operational, checkout, or testing phases; and the average data rate from the EOS satellites in orbit at any one time is expected to be from 18 to 60 Mbps. Providing the data processing and flight operations support for EOS will be the EOSDIS Core System (ECS). The ECS will command and control the spacecraft; process and store the EOS data; provide access to the data for years; and support researchers. The data processing aspects of the ECS consist of a collection of Distributed Active Archive Centers (DAAC's) which perform the product generation, data archive and distribution, and information management services. Flight operations aspects will be provided by the EOS Operations Center, by instrument control centers, and by widely distributed instrument support terminals. The communications and system management aspects will be provided by the EOSDIS Science Network and the System Management Center. In addition to the EOS satellite data, other data sets from earlier earth science missions are also to be added to designated DAAC's. Other ground data systems which will provide support to EOS for acquiring, transporting, processing, and distributing the transformed spacecraft data are currently being defined or are being upgraded for the EOS era. These systems include the Space Network consisting of the Tracking and Data Relay Satellite System (TDRSS), the TDRSS Ground Terminals, and the Network Control Center as well as the night Dynamics Facility, the EOS Data and Operations System, and EOS Communications. This paper briefly describes data handling by the ECS, the support data systems, their interfaces, and their roles.

Smith, Gene↗

DOE OSTI2025

Core design and performance of the Westinghouse lead fast reactor with UO 2 and MOX configurations

For this work, Westinghouse partnered with Argonne National Laboratory to design, model and optimize UO 2 - and MOX-fueled core designs for a medium size (950 MWt) Lead Fast Reactor that was pursued by Westinghouse. Using Argonne’s suite of reactor analysis codes together with Westinghouse fuel cost economic models, thousands of candidate cores were considered to achieve the economics-optimized cores presented in this paper. This optimization process considered detailed reactor physics, fuel performance, transient performance, and fuel economics models. The reactor performance of the resulting optimized UO 2 - and MOX-fueled core designs are described and compared in this paper. Both cores show fuel performance and transient behavior that is considered acceptable for the optimization presented herein, while further testing campaigns on material performance in high-temperature liquid lead will be required to confirm acceptability at the operating conditions chosen. A multi-batch strategy was selected for the UO 2 core for best fuel utilization with minimum fuel inventory costs. A single-batch fuel management was instead selected for the MOX core to maximize cycle length and minimize the impact of the longer refueling outage resulting from the higher decay heat of the discharged MOX fuel relative to the discharged UO 2 fuel, requiring a longer cooling time before dry-lift of discharged fuel could take place.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗