Search NASA⌕ Search

SEARCH · Search NASA

Results for “damage threshold”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

High power experimental studies of hybrid photonic band gap accelerator structures

This paper reports the first high power tests of hybrid Photonic Band Gap (PBG) accelerator structures. Three hybrid PBG (HPBG) structures were designed, built and tested at 17.14 GHz. Each structure had a triangular lattice array with 60 inner sapphire rods and 24 outer copper rods sandwiched between copper disks. The dielectric PBG band gap map allows the unique feature of overmoded operation in a TM02 mode, with suppression of both lower order modes, such as the TM11 mode, as well as higher order modes. The use of sapphire rods, which have negligible dielectric loss, required inclusion of the dielectric birefringence in the design. The three structures were designed to sequentially reduce the peak surface electric field. Simulations showed relatively high surface fields at the triple point as well as in any gaps between components in the clamped assembly. The third structure used sapphire rods with small pin extensions at each end and obtained the highest gradient of 19 MV/m, corresponding to a surface electric field of 78 MV/m, with a breakdown probability of 0.5 per pulse per meter for a 100-ns input power pulse. Operation at a gradient above 20 MV/m led to runaway breakdowns with extensive light emission and eventual damage. For all three structures, multipactor light emission was observed at gradients well below the breakdown threshold. This research indicated that multipactor triggered at the triple point limited the operational gradient of the hybrid structure.

43 PARTICLE ACCELERATORS↗

Stress-corrosion cracking in metals

Criteria and recommended practices for preventing stress-corrosion cracking from impairing the structural integrity and flightworthiness of space vehicles are presented. The important variables affecting stress-corrosion cracking are considered to be the environment, including time and temperature; metal composition, and structure; and sustained tensile stress. For designing spacecraft structures that are free of stress-corrosion cracking for the service life of the vehicle the following rules apply: (1) identification and control of the environments to which the structure will be exposed during construction, storage, transportation, and use; (2) selection of alloy compositions and tempers which are resistant to stress-corrosion cracking in the identified environment; (3) control of fabrication and other processes which may introduce residual tensile stresses or damage the material; (4) limitation of the combined residual and applied tensile stresses to below the threshold stress level for the onset of cracking throughout the service life of the vehicle; and (5) establishment of a thorough inspection program.

Source record↗

Variation in SEU sensitivity of dose-imprinted CMOS SRAMs

The authors report on an experimental study of dose-induced changes in SEU (single-event-upset) sensitivity of CMOS static RAMs. Two time regimes were investigated following exposure of memories to cobalt-60 gamma rays: the near term, within a few hours after exposure, and the long term, after many days. Samples were irradiated both at room and at liquid nitrogen temperatures. The latter procedure was used in order to freeze in the damage state until SEU measurements could be made prior to annealing. Results show that memories damaged by dose are more sensitive to upsets by heavy ions. The induced changes are substantial: threshold linear energy transfer (LET) values decreased by as much as 46 percent and asymptotic cross sections increased by factors of two to four (unannealed samples).

Stassinopoulos, E. G.↗

Laser Damage Growth in Fused Silica with Simultaneous 351 nm and 1053 nm irradiation

Laser-induced growth of optical damage often determines the useful lifetime of an optic in a high power laser system. We have extended our previous work on growth of laser damage in fused silica with simultaneous 351 nm and 1053 nm laser irradiation by measuring the threshold for growth with various ratios of 351 nm and 1053 nm fluence. Previously we reported that when growth occurs, the growth rate is determined by the total fluence. We now find that the threshold for growth is dependent on both the magnitude of the 351 nm fluence as well as the ratio of the 351 nm fluence to the 1053 nm fluence. Furthermore, the data suggests that under certain conditions the 1053 nm fluence does not contribute to the growth.

42 ENGINEERING↗

The Probability of False Go/No-Go Determined by GOES Proton Flux: Proposed Launch Constraints for Avoiding Damaging Solar Energetic Particle Events

Most space-bound hardware needs to be designed to withstand space weather events to some degree. Long-term predictability of space weather events, such as solar flares or coronal mass ejections, are still a matter of theory so designers should assume a worst case event for their specific environment. In our analysis, we show preliminary results of the probability of encountering a false/true go/no-go based on a threshold launch and design proton environment. The goal in choosing a threshold launch environment is to avoid the chance of exceeding the design environment during vulnerable parts of the mission. Operationally, this method cannot predict damaging space weather but can aid in avoiding space weather events that are already occurring. The GOES (Geostationary Operational Environmental Satellite) proton flux database is used as a proxy for the heavy ion fluxes, which impart a greater threat because of larger single event upsets and effects. Our use of protons as a proxy for heavy ions is justified on the basis of the correlation between their fluxes shown by a qualitative comparison of GOES proton integral fluxes at greater than 10 megaelectronvolts and ACE/SIS (Advanced Composition Explorer / Solar Isotope Spectrometer) heavy ion integral fluxes.

DeStefano, Anthony M.↗

Optical spectroscopy study of modifications induced in cerium dioxide by electron and ion irradiations

UV-visible absorption spectroscopy and Raman spectroscopy were used to study damage production in cerium dioxide epitaxial films and polycrystalline sintered samples after irradiation with electrons for three energies to span the threshold displacement energies of cerium and oxygen atoms, and 2.4-MeV Cu ions. Neither amorphization nor specific colour-centre bands were detected. Evolutions of the refractive index were derived from the interference fringes in the optical transmission spectra of epilayers after irradiation. No significant change of the refractive index occurred for the 1.0-MeV electron irradiation, whereas a maximum decrease by 28± 8% was deduced for the 1.4-MeV and 2.5-MeV energies. These modifications are consistent with ballistic damage on the cerium sublattice for high electron energies producing Ce 3+ ions. Yet, no significant change of refractive index was found for the Cu ion irradiation. This likely originates from the high rate of Frenkel pair recombination in the collision cascades induced by more energetic recoils than for the electron irradiations, combined with electronic excitations and hole capture on Ce 3+ ions. This study reveals modifications of the electronic structure upon irradiation that could take place in other non-amorphizable oxide systems.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Correlation between simulations and cavitation-induced erosion damage in Spallation Neutron Source target modules after operation

An explicit finite element (FE) technique developed for estimating dynamic strain in the Spallation Neutron Source (SNS) mercury target module vessel is now providing insight into cavitation damage patterns observed in used targets. The technique uses an empirically developed material model for the mercury that describes liquid-like volumetric stiffness combined with a tensile pressure cut-off limit that approximates cavitation. The longest period each point in the mercury is at the tensile cut-off threshold is denoted its saturation time. Now, the pattern of saturation time can be obtained from these simulations and is being positively correlated with observed damage patterns and is interpreted as a qualitative measure of damage potential. Saturation time has been advocated by collaborators at J-Parc as a factor in predicting bubble nuclei growth and collapse intensity. The larger the ratio of maximum bubble size to nucleus, the greater the bubble collapse intensity to be expected; longer saturation times result in greater ratios. With the recent development of a user subroutine for the FE solver saturation time is now provided over the entire mercury domain. Its pattern agrees with spots of damage seen above and below the beam axis on the SNS inner vessel beam window and elsewhere. The other simulation result being compared to observed damage patterns is mercury velocity at the wall. Related R&D has provided evidence for the damage mitigation that higher wall velocity provides. In comparison to observations in SNS targets, inverse correlation of high velocity to damage is seen. In effect, it is the combination of the patterns of saturation time and low velocity that seems to match actual damage patterns.

cavitation↗

Relative Contributions of Radiation and Cisplatin-Based Chemotherapy to Sensorineural Hearing Loss in Head-and-Neck Cancer Patients

Purpose: To investigate the risk of sensorineural hearing loss (SNHL) in patients with head-and-neck cancer and treated with radiation therapy (RT) or concomitant cisplatin-based chemoradiation, the relationship among SNHL and radiation dose to the cochlea, the use of two common cisplatin dose regimens. Methods and Materials: A total of 62 head-and-neck cancer patients treated with curative intent were included in this prospective study. Of the patients, 21 received RT alone, 27 received 40 mg/m{sup 2} weekly cisplatin, 13 received 100 mg/m{sup 2} every 3 weeks during RT, and 1 received RT with weekly epidermal growth factor receptor inhibitor antibody. The effect of chemotherapy and RT dose on hearing was determined using a model that accounted for the age and variability between each ear for each patient. Results: We constructed a model to predict dose-dependent hearing loss for RT or cisplatin-based chemotherapy either alone or in combination. For patients only receiving RT, no significant hearing loss was found at doses to the cochlea of less than 40 Gy. Patients receiving 100 mg/m{sup 2} or 40 mg/m{sup 2} of cisplatin chemotherapy had an estimated +21.5 dB and +9.5 dB hearing loss at 8,000 Hz with low radiation doses (10 Gy), which rose to +38.4 dB and +18.9 dB for high radiation doses (40 Gy). Conclusions: Use of RT alone with doses of less than 40 Gy did not result in clinically significant hearing loss. High-frequency SNHL was profoundly damaged in patients who received concomitant cisplatin when doses of 100 mg/m{sup 2} were used. The threshold cochlear dose for hearing loss with cisplatin-based chemotherapy and RT was predicted to be 10 Gy. The inner ear radiation dose constraints and cisplatin dose intensity should be considered in the treatment of advanced head-and-neck cancer.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Radiation damage formation in InP, InSb, GaAs, GaP, Ge, and Si due to fast ions

The basic physical mechanisms of damage formation in semiconductors due to swift heavy ion (SHI) irradiation are not yet fully understood. In the present paper damage evolution and the formation of ion tracks during SHI irradiation in InP, InSb, GaAs, GaP, and Ge are investigated for irradiation with Xe or Au ions having specific energies ranging from about 0.8 to 3 MeV/u. Based on these experimental results and those obtained by other authors for cluster-ion irradiation of InP, GaAs, Ge, and Si, extensive calculations were performed in the framework of the thermal spike model. As we published previously, the model was extended to correctly treat processes being specific to semiconductors. Additionally, the computer code was modified to perform calculations for cluster ions too. The calculated track radii are compared with those measured for the various irradiation conditions. Thereby, one unknown parameter in the calculations was determined by fitting one data point. With this procedure a very good agreement between calculated and measured track radii is obtained for InP, Ge, and Si irradiated under various conditions. This implies that the extended thermal spike model is well capable to explain track formation in SHI irradiated semiconductors. Furthermore, special experiments were performed, the results of which also support the thermal spike model of ion track formation and contradict competing mechanisms such as Coulomb explosion, shock waves, or lattice relaxation. Thus, visible (amorphous/heavily damaged) ion tracks occur if the electronic energy deposition per ion and unit length clearly exceeds the threshold value necessary for melting. This is possible for elemental ion irradiation of InP and InSb. In Ge and Si (and probably also in GaAs and GaP) the energy deposition necessary for melting is that high that it cannot be reached by elemental ion irradiation. Moreover, at least in InP and GaAs ion tracks can be formed also in a subthreshold irradiation regime if the material is predamaged. This suggests that the existence of point defects and clusters of point defects in the crystal lattice noticeably increases the electron-phonon coupling efficiency, resulting in a more efficient energy transfer to the lattice. Within the thermal spike model, this means that for a given electronic energy deposition in the predamaged crystal a higher temperature is reached than in the perfect one.

36 MATERIALS SCIENCE↗

Characterization of Mode 1 and Mode 2 delamination growth and thresholds in graphite/peek composites

Composite materials often fail by delamination. The onset and growth of delamination in AS4/PEEK, a tough thermoplastic matrix composite, was characterized for mode 1 and mode 2 loadings, using the Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) test specimens. Delamination growth per fatigue cycle, da/dN, was related to strain energy release rate, G, by means of a power law. However, the exponents of these power laws were too large for them to be adequately used as a life prediction tool. A small error in the estimated applied loads could lead to large errors in the delamination growth rates. Hence strain energy release rate thresholds, G sub th, below which no delamination would occur were also measured. Mode 1 and 2 threshold G values for no delamination growth were found by monitoring the number of cycles to delamination onset in the DCB and ENF specimens. The maximum applied G for which no delamination growth had occurred until at least 1,000,000 cycles was considered the threshold strain energy release rate. Comments are given on how testing effects, facial interference or delamination front damage, may invalidate the experimental determination of the constants in the expression.

Martin, Roderick H.↗

Characterization of Mode I and Mode II delamination growth and thresholds in AS4/PEEK composites

Composite materials often fail by delamination. The onset and growth of delamination in AS4/PEEK, a tough thermoplastic matrix composite, was characterized for mode 1 and mode 2 loadings, using the Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) test specimens. Delamination growth per fatigue cycle, da/dN, was related to strain energy release rate, G, by means of a power law. However, the exponents of these power laws were too large for them to be adequately used as a life prediction tool. A small error in the estimated applied loads could lead to large errors in the delamination growth rates. Hence strain energy release rate thresholds, G sub th, below which no delamination would occur were also measured. Mode 1 and 2 threshold G values for no delamination growth were found by monitoring the number of cycles to delamination onset in the DCB and ENF specimens. The maximum applied G for which no delamination growth had occurred until at least 1,000,000 cycles was considered the threshold strain energy release rate. Comments are given on how testing effects, facial interference or delamination front damage, may invalidate the experimental determination of the constants in the expression.

Martin, Roderick H.↗

Durability Assessment of Gamma Tial

Gamma TiAl was evaluated as a candidate alloy for low-pressure turbine blades in aeroengines. The durability of g-TiAl was studied by examining the effects of impact or fretting on its fatigue strength. Cast-to-size Ti-48Al-2Cr-2Nb was studied in impact testing with different size projectiles at various impact energies as the reference alloy and subsequently fatigue tested. Impacting degraded the residual fatigue life. However, under the ballistic impact conditions studied, it was concluded that the impacts expected in an aeroengine would not result in catastrophic damage, nor would the damage be severe enough to result in a fatigue failure under the anticipated design loads. In addition, other gamma alloys were investigated including another cast-to-size alloy, several cast and machined specimens, and a forged alloy. Within this Ti-48-2-2 family of alloys aluminum content was also varied. The cracking patterns as a result of impacting were documented and correlated with impact variables. The cracking type and severity was reasonably predicted using finite element models. Mean stress affects were also studied on impact-damaged fatigue samples. The fatigue strength was accurately predicted based on the flaw size using a threshold-based, fracture mechanics approach. To study the effects of wear due to potential applications in a blade-disk dovetail arrangement, the machined Ti-47-2-2 alloy was fretted against In-718 using pin-on-disk experiments. Wear mechanisms were documented and compared to those of Ti-6Al-4V. A few fatigue samples were also fretted and subsequently fatigue tested. It was found that under the conditions studied, the fretting was not severe enough to affect the fatigue strength of g-TiAl.

Draper, Susan L.↗

Modulation of DNA polymerase beta-dependent base excision repair in cultured human cells after low dose exposure to arsenite

Base excision repair (BER) is crucial for development and for the repair of endogenous DNA damage. However, unlike nucleotide excision repair, the regulation of BER is not well understood. Arsenic, a well-established human carcinogen, is known to produce oxidative DNA damage, which is repaired primarily by BER, whilst high doses of arsenic can also inhibit DNA repair. However, the mechanism of repair inhibition by arsenic and the steps inhibited are not well defined. To address this question we have investigated the regulation of DNA polymerase {beta} (Pol {beta}) and AP endonuclease (APE1), in response to low, physiologically relevant doses of arsenic. GM847 lung fibroblasts and HaCaT keratinocytes were exposed to sodium arsenite, As(III), and mRNA, protein levels and BER activity were assessed. Both Pol {beta} and APE1 mRNA exhibited significant dose-dependant down regulation at doses of As(III) above 1 {mu}M. However, at lower doses Pol {beta} mRNA and protein levels, and consequently, BER activity were significantly increased. In contrast, APE1 protein levels were only marginally increased by low doses of As(III) and there was no correlation between APE1 and overall BER activity. Enzyme supplementation of nuclear extracts confirmed that Pol {beta} was rate limiting. These changes in BER correlated with overall protection against sunlight UV-induced toxicity at low doses of As(III) and produced synergistic toxicity at high doses. The results provide evidence that changes in BER due to low doses of arsenic could contribute to a non-linear, threshold dose response for arsenic carcinogenesis.

60 APPLIED LIFE SCIENCES↗

Photonuclear cross sections for the 197 Au ⁢(𝛾, 𝑝⁢𝑛)⁢ 195⁢𝑚 Pt reaction near threshold

Platinum radioisotopes are of growing interest for targeted cancer therapy and diagnostic imaging because their decay delivers highly localized radiation doses in tissue, herewith enabling precise DNA damage through Auger-electron emission. Developing production technologies that provide platinum isotopes with high specific activity is essential in radioisotope therapy. Photonuclear reactions on stable nuclei offer a viable accelerator-based route for isotope production when supported by reliable cross-section data. We report photonuclear cross-section measurements for the 197 Au(γ, pn) 195m Pt reaction at incident γ-ray energies of 27, 29, and 31 MeV using the activation method. The measurements were performed by irradiating a stack of concentric-ring gold targets with a quasi-monoenergetic γ-ray beam provided by the High Intensity Gamma-ray Source (HI γS). The induced 195m Pt activity was quantified using off-line γ-ray spectroscopy. These data provide the first experimental constraints on the 197 Au(γ, pn) 195m Pt cross section in the near-threshold region. Furthermore, the comparison of the measured excitation function to PHITS and TALYS calculations indicates that the reaction becomes measurable only near 30 MeV and that substantially higher bremsstrahlung end-point energies are required for practically meaningful production.

190 ≤ A ≤ 219↗

Thermal annealing of radiation damage in CMOS ICs in the temperature range -140 C to +375 C

Annealing of radiation damage was investigated in the commercial, Z- and J-processes of the RCA CD4007A ICs in the temperature range from -140 C to +375 C. Tempering curves were analyzed for activation energies of thermal annealing, following irradiation at -140 C. It was found that at -140 C, the radiation-induced shifts in the threshold potentials were similar for all three processes. The radiation hardness of the Z- and J-process is primarily due to rapid annealing of radiation damage at room temperature. In the region -140 to 20 C, no dopant-dependent charge trapping is seen, similar to that observed at higher temperatures. In the unbiased Z-process n-channels, after 1 MeV electron irradiation, considerable negative charge remains in the gate oxide.

Danchenko, V.↗

In situ detection of RF breakdown on microfabricated surface ion traps

We report microfabricated surface ion traps are a principal component of many ion-based quantum information science platforms. The operational parameters of these devices are pushed to the edge of their physical capabilities as the experiments strive for increasing performance. When the applied radio-frequency (RF) voltage is increased excessively, the devices can experience damaging electric discharge events known as RF breakdown. We introduce two novel techniques for in situ detection of RF breakdown, which we implemented while characterizing the breakdown threshold of surface ion traps produced at Sandia National Laboratories. In these traps, breakdown did not always occur immediately after increasing the RF voltage, but often minutes or even hours later. This result is surprising in the context of the suggested mechanisms for RF breakdown in vacuum. Additionally, the extent of visible damage caused by breakdown events increased with the applied voltage. To minimize the probability for damage when RF power is first applied to a device, our results strongly suggest that the voltage should be ramped up over the course of several hours and monitored for breakdown.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Crack Growth Behavior in the Threshold Region for High Cycle Fatigue Loading

This presentation describes results obtained from a research project conducted at the NASA Johnson Space Center (JSC) that was jointly supported by the FAA Technical Center and JSC. The JSC effort was part of a multi-task FAA program involving several U.S. laboratories and initiated for the purpose of developing enhanced analysis tools to assess damage tolerance of rotorcraft and aircraft propeller systems. The research results to be covered in this presentation include a new understanding of the behavior of fatigue crack growth in the threshold region. This behavior is important for structural life analysis of aircraft propeller systems and certain rotorcraft structural components (e.g., the mast). These components are often designed to not allow fatigue crack propagation to exceed an experimentally determined fatigue crack growth threshold value. During the FAA review meetings for the program, disagreements occurred between the researchers regarding the observed fanning (spread between the da/dN curves of constant R) in the threshold region at low stress ratios, R. Some participants believed that the fanning was a result of the ASTM load shedding test method for threshold testing, and thus did not represent the true characteristics of the material. If the fanning portion of the threshold value is deleted or not included in a life analysis, a significant penalty in the calculated life and design of the component would occur. The crack growth threshold behavior was previously studied and reported by several research investigators in the time period: 1970-1980. Those investigators used electron microscopes to view the crack morphology of the fatigue fracture surfaces. Their results showed that just before reaching threshold, the crack morphology often changed from a striated to a faceted or cleavage-like morphology. This change was reported to have been caused by particular dislocation properties of the material. Based on the results of these early investigations, a program was initiated at JSC to repeat these examinations on a number of aircraft structural alloys that were currently being tested for obtaining fatigue crack growth properties. These new scanning electron microscope (SEM) examinations of the fatigue fracture faces confirmed the change in crack morphology in the threshold crack tip region. In addition, SEM examinations were further performed in the threshold crack-tip region before breaking the specimens open (not done in the earlier published studies). In these examinations, extensive crack forking and even 90-degree crack bifurcations were found to have occurred in the final threshold crack-tip region. The forking and bifurcations caused numerous closure points to occur that prevented full crack closure in the threshold region, and thus were the cause of the fanning at low-R values. Therefore, we have shown that the fanning behavior was caused by intrinsic dislocation properties of the different alloy materials and were not the result of a plastic wake that remains from the load-shedding test phase. Also, to accommodate the use of da/dN data which includes fanning at low R-values, an updated fanning factor term has been developed and will be implemented into the NASGRO fatigue crack growth software. The term can be set to zero if it is desired that the fanning behavior is not be modeled for particular cases, such as when fanning is not a result of the intrinsic properties of a material.

Forman, Royce G.↗

Passive Low-Energy Nuclear-Recoil Detection with Color Centers

Crystal-damage events such as tracks and point defects have been used to record and detect radiation for a long time and recently they have been proposed as a means for dark-matter detection. Color centers can be read out optically and we propose a scheme based on selective plane illumination microscopy for micrometer-scale imaging of large volumes corresponding to kilogram mass detectors. This class of detectors would be passive and would operate at room temperature and we call this the passive low-energy optical color-center nuclear-recoil (PALEOCCENE) detection method. We apply these concepts to the detection of reactor neutrinos using coherent elastic neutrino nucleus scattering (CE ν NS). Crystal-damage formation energies are intrinsically on the order of 25 eV, resulting in similarly low nuclear-recoil thresholds. Furthermore, this would enable the observation of reactor-neutrino CE ν NS with detectors as small as 10 g. Additionally, a competitive search for spin-dependent dark-matter scattering down to a dark-matter mass of 0.3 GeV could be possible. Passive crystal detectors might also be attractive for nuclear-nonproliferation safeguards if used to monitor reactor power and to put limits on plutonium production. The passive nature and small footprint of the proposed detectors implies that these might fit well within accepted reactor-safeguards operations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗