Search NASA⌕ Search

SEARCH · Search NASA

Results for “diffractive computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Evaluation of a thermomechanical model for prediction of residual stress during laser powder bed fusion of Ti-6Al-4V

The build-up of residual stresses in a part during laser powder bed fusion provides a significant limitation to the adoption of this process. These residuals stresses may cause a part to fail during a build or fall outside the specified tolerances after fabrication. In the present work a thermomechanical model is used to simulate the build process and calculate the residual stress state for Ti–6Al–4V specimens built with continuous and island scan strategies. A layer agglomeration, or lumping, approach is used to speed up the computations. A material model is developed to naturally capture the strain-rate dependence and annealing behavior of Ti–6Al–4V at elevated temperatures. Conclusions from the thermomechanical simulations showed good agreement with synchrotron X-ray diffraction measurements used to determine the residual elastic strains in these parts. Yet, the experimental measurements showed higher residual strains for the specimen built with an island scan strategy; a trend not fully captured by the simulations. Parameter studies were performed to fully understand the advantages and limitations of the current simulation methodology. Reasons for both the computational and experimental findings are discussed.

36 MATERIALS SCIENCE↗

Part-scale evolution of fine-scale microstructural heterogeneity in solid-state additive manufacturing

Current solid-state additive manufacturing methods, refined through costly and time-consuming trial and error, have spurred interest in computational models that replicate material behavior under typical thermomechanical conditions (e.g., strain-rate ~ 102 s−1). These models, however, struggle to capture time-dependent microstructural evolution. In this work, Additive Friction-Stir Deposition (AFSD) is used as a representative case study for part-scale quantification of microstructure evolution at a fine spatial resolution (200 μm) by examining a liquid-nitrogen-cooled stop-action build via energy-dispersive X-ray diffraction coupled with a multi-channel detector. These results inform modeling efforts by linking process asymmetry to stored plastic strain, residual elastic strain, and texture development, and unlike current state-of-the-art characterization methods (e.g., EBSD or neutron diffraction), this approach provides both the spatial resolution and collection efficiency necessary to quantify fine-scale microstructural heterogeneity over large component volumes. As such, this technique provides essential validation data for computational models, e.g., crystal plasticity, enabling future prediction of heterogeneous behavior in AFSD and other additive manufacturing processes.

Franz, Cole [ORNL] (ORCID:0000000213465881)↗

Understanding the Polymorphism of Cobalt Nanoparticles Formed in Electrodeposition–An In Situ XRD Study

An advanced synchrotron-based in situ X-ray diffraction (XRD) technique is successfully developed and employed to track and monitor the formation and phase selection of cobalt (Co) in electrodeposition in real time and verify DFT computational results. The impacts of a number of controlling factors including the pH of the electrolyte and deposition overpotential are systematically studied. The results show that the yielded phase of the electrodeposited Co is controlled by both thermodynamics and kinetics. The low pH low overpotential condition favors the formation of the thermodynamically stable fcc phase. While the high pH high overpotential condition promotes the formation of the metastable hcp phase. The experimental results agree well with the nanometric phase diagram computed with DFT. Layer-by-layer alternative stacking of fcc-hcp polymorphic phases can be facilely fabricated by just varying the overpotential. This work not only offers an effective means to control the phase of electroplating of Co but also presents a new approach to reveal the fundamental insights of the formation of metals under electrochemical reduction driving force.

36 MATERIALS SCIENCE↗

Estimation of micro-Hall-Petch coefficients for prismatic slip system in Mg-4Al as a function of grain boundary parameters

Grain size strengthening, referred to as the Hall-Petch effect, is a common strategy to improve the yield strength of magnesium (Mg) alloys. Several experimental studies have reported that the Hall-Petch slope strongly depends on the texture of the alloy. This effect arises from altering grain boundaries (GBs) resistance to different slip systems to transfer across adjacent grains. The grain boundary barrier strength of certain grain boundaries to basal slip, referred to as basal micro-Hall-Petch, was investigated in the previous work. Here in this study, the micro-Hall-Petch coefficient values for the prismatic slip $(k^{prismatic}_{μ})$ in Mg-4Al and their correlation with the grain boundary parameters were investigated. An experimental method was developed to initiate the prismatic slip band at low-stress levels. High-resolution electron backscatter diffraction (HR-EBSD) was used to measure the residual stress tensor, from which the resolved shear stress ahead of blocked prismatic slip bands was computed for seven different grain boundaries. $(k^{prismatic}_{μ})$ values for each individual GB were calculated by coupling the stress profile information with a continuum dislocation pile-up model. The $(k^{prismatic}_{μ})$ values vary from 0.138 MPa.m 1/2 to 0.685 MPa. m 1/2 which are almost three times larger than the calculated values for the basal micro-Hall-Petch. The $(k^{prismatic}_{μ})$ values were correlated with the GB parameters, and a functional relationship depending on the two most effective angles, the angle between the traces of the slip planes on the GB plane ($\phi$) and the angle between incoming and outgoing slip directions (κ), was proposed to estimate the Hall-Petch barrier for prismatic slip system. The work provides coefficients that can be supplied as input to crystal plasticity models to couple the effect of texture and grain size effectively.

36 MATERIALS SCIENCE↗

Ion Tracks and Microstructures in Barium Titanate Irradiated with Swift Heavy Ions: A Combined Experimental and Computational Study

Tetragonally structured BaTiO3 single crystals were irradiated using 635 MeV 238U+ ions to fluences of 1E7, 5E10 and 1.4E12 ions/cm2 at room temperature. Subsequent sample characterizations were performed using ion channeling, x-ray diffraction (XRD), helium ion microscopy, and transmission electron microscopy. The results show that there are lattice relaxation and recovery of pre-existing defects in the irradiated samples. Various structures representing different regimes of electronic and nuclear interactions along the ion track are observed. The track on the surface has an amorphous core of up to ~10 nm in diameter, surrounded by a strained lattice structure. The core size is roughly proportional to the square root of the electronic stopping power. Satellite-like defects around the core are also present. The ring of cubic phase expected to form around the amorphous core does not appear, probably due to a reversible phase transition as confirmed by an in-situ XRD study. Modeling and simulation are also attempted to interpret the data and gain physical insights. We have developed a partial charge model for cubic BaTiO3 that reproduces its lattice constants, elastic constants, and melting temperature. Using the interatomic potential, we have performed molecular dynamics simulations of the irradiation damage in BaTiO3. The results show that an amorphous track of ~1.2 nm in radius forms under thermal energy deposition at dE(T)/dx = 5 keV/nm. At 20 keV/nm, the radius increases to ~4.5 nm with an order of magnitude increase in the number of defects. The simulation also reveals details of the bonding environments and shows that the amorphous zones produced at different dE(T)/dx values have different densities. The combined experimental and computational data suggest that there is a significant interfacial recrystallization of the as-created amorphous cores during the cooling-down stage of thermal spikes.

barium titanate↗

Neutron Radiography and Computed Tomography of Biological Systems at the Oak Ridge National Laboratory's High Flux Isotope Reactor

Neutrons have historically been used for a broad range of biological applications employing techniques such as small-angle neutron scattering, neutron spin echo, diffraction, and inelastic scattering. Unlike neutron scattering techniques that obtain information in reciprocal space, attenuation-based neutron imaging measures a signal in real space that is resolved on the order of tens of micrometers. The principle of neutron imaging follows the Beer-Lambert law and is based on the measurement of the bulk neutron attenuation through a sample. Greater attenuation is exhibited by some light elements (most notably, hydrogen), which are major components of biological samples. Contrast agents such as deuterium, gadolinium, or lithium compounds can be used to enhance contrast in a similar fashion as it is done in medical imaging, including techniques such as optical imaging, magnetic resonance imaging, X-ray, and positron emission tomography. For biological systems, neutron radiography and computed tomography have increasingly been used to investigate the complexity of the underground plant root network, its interaction with soils, and the dynamics of water flux in situ. Moreover, efforts to understand contrast details in animal samples, such as soft tissues and bones, have been explored. This manuscript focuses on the advances in neutron bioimaging such as sample preparation, instrumentation, data acquisition strategy, and data analysis using the High Flux Isotope Reactor CG-1D neutron imaging beamline. The aforementioned capabilities will be illustrated using a selection of examples in plant physiology (herbaceous plant/root/soil system) and biomedical applications (rat femur and mouse lung).

Bilheux, Hassina↗

The Focus of an Ultraintense Laser Pulse

Back in 1885, von Lommel studied the diffraction of a circular opening. His study was one step further than the Airy diffraction model (describing patterns in the focal plane) because von Lommel’s model was able to describe what the light distribution before and after the focus is. Today’s extreme lasers have a flat-top profile whose diffraction pattern in the vicinity of the focus is very much reminiscent of von Lommel’s description. In the present Chapter, we will compute, based on a Huygens-Fresnel integral method, the laser field distribution around the focus. This modelling is particularly important because the intensity distribution before and after the focal plane (where the Airy disk exists) is very relevant to many contemporary experiments, and is key to the ionization of atoms and the dynamics of liberated electrons. For clarity, we are going to analyze three cases corresponding to three f-numbers: f/10, f/1.8, and f/1.1. Our computed results reveal the present-day significance of von Lommel’s pioneering results. Here, they help us understand the light distribution in the entire focal region of an ultraintense laser pulse including the full vectorial fields, not just the focal plane.

Roso, Luis [Universidad de Salamanca (Spain)]↗

Evaluation of pore structures and cracking in cement paste exposed to elevated temperatures by X-ray computed tomography

When cement-based materials are exposed to the high temperatures induced by fire, which can rapidly cause temperatures of over 1000 °C, the changes in pore structure and density prevail. In the present study, mortar specimens were subjected to a series of increasing temperatures to explore the temperature-dependent evolution of internal pore structure. High-performance X-ray computed tomography (CT) was used to observe the evolution of temperature-induced discontinuities at the sub-millimeter level. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were employed to investigate the cause of physical changes in the heated mortar specimens. Results exhibit the changes in pore structure caused by elevated temperatures, and thermally induced fractures. We discuss the progressive formation of thermally induced fracture networks, which is a prerequisite for spalling failure of cement-based materials by fire, based on visual observations of the 3D internal structures revealed by X-ray CT.

36 MATERIALS SCIENCE↗

Leaching characteristics of calcium-based compounds in MSWI Residues: From the viewpoint of clogging risk

Highlights: • The leaching behavior of Ca-based compounds commonly in MSWI residues was studied. • pH is the crucial factor for calcium leaching process. • CaCO{sub 3} was the most sensitive to leaching temperature and Ca{sub 3}(PO{sub 4}){sub 2} was the least. • Ca leaching of MSWIBA and SAPCR attributed to CaCO{sub 3} and Ca{sub 3}(PO{sub 4}){sub 2} respectively. • Potential clogging ability of MSWI residues leachate in open air was calculated. - Abstract: Leachate collection system (LCS) clogging caused by calcium precipitation would be disadvantageous to landfill stability and operation. Meanwhile, calcium-based compounds are the main constituents in both municipal solid waste incineration bottom ash (MSWIBA) and stabilized air pollution control residues (SAPCR), which would increase the risk of LCS clogging once these calcium-rich residues were disposed in landfills. The leaching behaviors of calcium from the four compounds and municipal solid waste incineration (MSWI) residues were studied, and the influencing factors on leaching were discussed. The results showed that pH was the crucial factor in the calcium leaching process. CaCO{sub 3} and CaSiO{sub 3} began leaching when the leachate pH decreased to less than 7 and 10, respectively, while Ca{sub 3}(PO{sub 4}){sub 2} leached at pH < 12. CaSO{sub 4} could hardly dissolve in the experimental conditions. Moreover, the sequence of the leaching rate for the different calcium-based compounds is as follows: CaSiO{sub 3} > Ca{sub 3}(PO{sub 4}){sub 2} > CaCO{sub 3}. The calcium leaching from the MSWIBA and SAPCR separately started from pH < 7 and pH < 12, resulting from CaCO{sub 3} and Ca{sub 3}(PO{sub 4}){sub 2} leaching respectively, which was proven by the X-ray diffraction results. Based on the leaching characteristics of the different calcium compounds and the mineral phase of calcium in the incineration residues, simulated computation of their clogging potential was conducted, providing the theoretical basis for the risk assessment pertaining to LCS clogging in landfills.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Revealing the Role of Phase Structures of Bimetallic Nanocatalysts in the Oxygen Reduction Reaction

The ability to tune the atomic-level structure of alloy nanoparticles (NPs) is necessary for the design and preparation of active and stable catalysts for fuel cell reactions such as the oxygen reduction reaction (ORR), which is highly sensitive to the structure of the catalysts. We report here structurally tunable PdCu nanoparticle catalysts for the ORR obtained by varying the thermochemical treatment parameters. The phase type and the atomic structure of the nanoalloy catalysts strongly depend on the thermochemical treatment temperature and atmosphere, especially at low temperatures. While PdCu nanoalloys feature both body-centered cubic (bcc) and face-centered cubic (fcc) phase structures, a pure fcc structure, prepared by unusually low thermochemical treatment temperature, showed the highest catalytic activity for ORR. This was evidenced by a mass activity of eight times higher than that of commercial Pd catalyst. This activity enhancement was shown to be linked to the nanostructural tuning between fcc and bcc structures, as supported by systematic characterization using X-ray diffraction coupled with pair distribution function analysis. The impact of phase structure on the catalytic properties of the nanocatalyst is further substantiated by computational modeling based on density functional theory. Our results provide a fresh insight into the nanostructure-activity correlation at the atomic scale, which has significant implications for the design, synthesis, and processing of highly-active nanoalloy catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of manganese substitution of ferrite nanoparticles on particle grain structure

To investigate the influence of manganese substitution on the saturation magnetization of manganese ferrite nanoparticles, samples with various compositions (Mn x Fe 3–x O 4 , x = 0, 0.25, 0.5, 0.75, and 1) were synthesized and characterized. The saturation magnetization of such materials was both calculated using density functional theory and measured via vibrating sample magnetometry. A discrepancy was found; the computational data demonstrated a positive correlation between manganese content and saturation magnetization, while the experimental data exhibited an inverse correlation. X-ray diffraction (XRD) and magnetometry results indicated that the crystallite diameter and the magnetic diameter decrease when adding more manganese, which could explain the loss of magnetization of the particles. For 20 nm nanoparticles, with increasing manganese substitution level, the crystallite size decreases from 10.9 nm to 6.3 nm and the magnetic diameter decreases from 15.1 nm to 3.5 nm. Further high resolution transmission electron microscopy (HRTEM) analysis confirmed the manganese substitution induced defects in the crystal lattice, which encourages us to find ways of eliminating crystalline defects to make more reliable ferrite nanoparticles.

36 MATERIALS SCIENCE↗

Optical design concept of the CMB-S4 large-aperture telescopes and cameras

CMB-S4 -- the next-generation ground-based cosmic microwave background (CMB) experiment - will significantly advance the sensitivity of CMB measurements and improve our understanding of the origin and evolution of the universe. CMB-S4 will deploy large-aperture telescopes fielding hundreds of thousands of detectors at millimeter wavelengths. We present the baseline optical design concept of the large-aperture CMB-S4 telescopes, which consists of two optical configurations: (i) a new off-axis, three-mirror, free-form anastigmatic design and (ii) the existing coma-corrected crossed-Dragone design. We also present an overview of the optical configuration of the array of silicon optics cameras that will populate the focal plane with 85 diffraction-limited optics tubes covering up to 9 degrees of field of view, up to $1.1 \, \rm mm$ in wavelength. We describe the computational optimization methods that were put in place to implement the families of designs described here and give a brief update on the current status of the design effort.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Real-space Green’s function approach to photoelectron diffraction

We discuss the real-space Green’s function (RSGF) approach for core-level photoelectron diffraction (PD) and its comparison to x-ray absorption spectra (XAS). We focus especially on the separable Green’s function formalism for efficient calculations of high-order multiple scattering. Computational details such as scattering potentials, self-energy effects, Debye–Waller factors, and inelastic losses are discussed. Finally, we consider prospects for improving ab initio PD calculations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optical diffraction radiation from a dielectric and a metal nanowire excited by a modulated electron beam

The optical diffraction radiation that accompanies the motion of a modulated beam of electrons near a dielectric and silver nanowire scatterers is investigated in the two-dimensional formulation. Our goal is to compute the field in the near and far zones and analyze how it depends on electron beam parameters. We demonstrate the excitation of internal resonances of such a scatterer that can be useful in the design of nanoscale non-invasive beam position monitors.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Experimental equation of state of 11 lanthanide nitrides (NdN to LuN) and pressure induced phase transitions in NdN, SmN, EuN, and GdN

Through an extensive data analysis of powder X-ray diffraction data obtained at pressures up to at least 78 GPa, we report the experimental equations of state for all lanthanide nitrides between NdN and LuN, excluding the radioactive Pm. By fitting the obtained unit cell volumes as a function of pressure with the third order Birch–Murnaghan equation of state, we find that the bulk modulus increases with an increasing lanthanide number from K 0 = 146(12) GPa for NdN to 182(7) GPa in EuN. Hereafter, the bulk modulus reaches a plateau for the rest of the series except for TmN which has a lower bulk modulus. We find that the first derivative of the bulk modulus is around 4 for all compounds except TbN, which displays a significantly different compression behavior. In addition, we find a B1 to B10 pressure-induced phase transition in NdN, SmN, EuN, and GdN at increasingly higher pressures. In fact, we observe that the onset pressure of the phase transition increases linearly with Ln atomic number. From TbN and onwards, we do not observe any sign of a B1 to B10 transition indicating that the transition pressure exceeds the studied pressure range. Therefore, we believe that, for the heavier lanthanides, the linear relationship between the onset pressure and the lanthanide number does not hold and even higher pressures are needed to observe the transition. This coherent study of the series of lanthanide nitrides offers a unique opportunity for benchmark studies of computational methods applied to compounds with 4f electrons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Scattering of radio frequency waves by blobs in tokamak plasmas

The density fluctuations and blobs present in the edge region of magnetic fusion devices can scatter radio frequency (RF) waves through refraction, reflection, diffraction, and coupling to other plasma waves. This, in turn, affects the spectrum of the RF waves and the electromagnetic power that reaches the core of the plasma. The usual geometric optics analysis of RF scattering by density blobs accounts for only refractive effects. It is valid when the amplitude of the fluctuations is small, of the order of 10%, compared to the background density. In experiments, density fluctuations with much larger amplitudes are routinely observed, so that a more general treatment of the scattering process is needed. In this paper, a full-wave model for the scattering of RF waves by a blob is developed. The full-wave approach extends the range of validity well beyond that of geometric optics; however, it is theoretically and computationally much more challenging. The theoretical procedure, although similar to that followed for the Mie solution of Maxwell's equations, is generalized to plasmas in a magnetic field. Besides diffraction and reflection, the model includes coupling to a different plasma wave than the one imposed by the external antenna structure. In the model, it is assumed that the RF waves interact with a spherical blob. The plasma inside and around the blob is cold, homogeneous, and imbedded in a uniform magnetic field. After formulating the complete analytical theory, the effect of the blob on short wavelength electron cyclotron waves and longer wavelength lower hybrid waves is studied numerically.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Neutron Diffraction Residual Strain Tensor Measurements Within The Phase IA Weld Mock-up Plate P-5

Oak Ridge National Laboratory (ORNL) has worked with NRC and EPRI to apply neutron and X-ray diffraction methods to characterize the residual stresses in a number of dissimilar metal weld mockups and samples. The design of the Phase IA specimens aimed to enable stress measurements by several methods and computational modeling of the weld residual stresses. The partial groove in the 304L stainless steel plate was filled with weld beads of Alloy 82. A summary of the weld conditions for each plate is provided in Table 1. The plates were constrained along the long edges during and after welding by bolts with spring-loaded washers attached to the 1-inch thick Al backing plate. The purpose was to avoid stress relief due to bending of the welded stainless steel plate. The neutron diffraction method was one of the methods selected by EPRI for non-destructive through thickness strain and stress measurement. Four different plates (P-3 to P-6) were studied by neutron diffraction strain mapping, representing four different welding conditions. Through thickness neutron diffraction strain mappings at NRSF2 for the four plates and associated strain-free d-zero specimens involved measurement along seven lines across the weld and at six to seven depths. The mountings of each plate for neutron diffraction measurements were such that the diffraction vector was parallel to each of the three primary orthogonal directions of the plate: two in-plane directions, longitudinal and transverse, and the direction normal to the plate (shown in left figure within Table 1). From the three orthogonal strains for each location, the residual stresses along the three plate directions were calculated. The principal axes of the strain and stress tensors, however, need not necessarily align with the plate coordinate system. To explore this, plate P-5 was selected for examination of the possibility that the principal axes of strain are not along the sample coordinate system axes. If adequate data could be collected the goal would be to determine the strain tensor's orientation and magnitude of strain along each principle axis direction.

36 MATERIALS SCIENCE↗

Estimation of Hoffman-Lauritzen parameters from nonisothermal crystallization kinetics of PET/MWCNT nanocomposites

Polyethylene terephthalate (PET) and Nucleated PET/ multi-walled carbon nanotubes (MWCNTs) nanocomposites with different MWCNTs loadings were prepared by melt compounding. The influence of the addition of MWCNTs and precipitated PET (p-PET) on the morphology and thermal properties of the nanocomposites was investigated. From Transmission Electronic Microscopy (TEM) and Wide angle X-Ray diffraction (WAXD) study, it can be clearly seen that nanocomposites with low MWCNTs contents (0.1 wt. %) get better MWCNTs dispersion than higher MWCNT loading. Comparing with PET, nucleated PET nanocomposite with 0.1% MWCNT loading shows higher value of Lauritzen-Hoffman parameters U* and Kg evaluated using the differential isoconversional method. Crystallization regime transition temperature range shifts to higher temperature (208°C - 215°C) for nanocomposites. The presence of p-PET in addition of MWCNT, which act as good nucleating agent, enhanced the crystallization of PET through heterogeneous nucleation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗