Search NASA⌕ Search

SEARCH · Search NASA

Results for “directional elements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

A miniature, directional surface-fence gage for three-dimensional turbulent boundary layer measurements

A new miniature (3.175 mm overall diameter) surface-fence gage was developed to measure simultaneously the magnitude and direction of wall shear stress under three-dimensional turbulent boundary layers. Two fence elements were placed orthogonal to each other on the end surface of the gage. The gage was calibrated for its directional and magnitude sensitivities. It was then tested under an axisymmetric swirling boundary layer, subject to a sudden transverse strain. The advantage of the gage was demonstrated, and excellent agreement was obtained with the results from surface oil flow interferometry and velocity field measurements. The results also compared well with numerical computations.

Higuchi, H.↗
NASA NTRS1987

Directional Solidification of Nodular Cast Iron

Cerium enhances formation of graphite nodules. Preliminary experiments in directional solidification of cast iron shows quantitative correlation of graphite microstructure with growth rate and thermal gradient, with sufficient spheroidizing element to form spheroidal graphite under proper thermal conditions. Experimental approach enables use of directional solidification to study solidification of spheriodal-graphite cast iron in low gravity. Possible to form new structural materials from nodular cast iron.

Curreri, P. A.↗
NASA NTRS2005

Deployable Wide-Aperture Array Antennas

Inexpensive, lightweight array antennas on flexible substrates are under development to satisfy a need for large-aperture antennas that can be stored compactly during transport and deployed to full size in the field. Conceived for use aboard spacecraft, antennas of this type also have potential terrestrial uses . most likely, as means to extend the ranges of cellular telephones in rural settings. Several simple deployment mechanisms are envisioned. One example is shown in the figure, where the deployment mechanism, a springlike material contained in a sleeve around the perimeter of a flexible membrane, is based on a common automobile window shade. The array can be formed of antenna elements that are printed on small sections of semi-flexible laminates, or preferably, elements that are constructed of conducting fabric. Likewise, a distribution network connecting the elements can be created from conventional technologies such as lightweight, flexible coaxial cable and a surface mount power divider, or preferably, from elements formed from conductive fabrics. Conventional technologies may be stitched onto a supporting flexible membrane or contained within pockets that are stitched onto a flexible membrane. Components created from conductive fabrics may be attached by stitching conductive strips to a nonconductive membrane, embroidering conductive threads into a nonconductive membrane, or weaving predetermined patterns directly into the membrane. The deployable antenna may comprise multiple types of antenna elements. For example, thin profile antenna elements above a ground plane, both attached to the supporting flexible membrane, can be used to create a unidirectional boresight radiation pattern. Or, antenna elements without a ground plane, such as bow-tie dipoles, can be attached to the membrane to create a bidirectional array such as that shown in the figure. For either type of antenna element, the dual configuration, i.e., elements formed of slots in a conductive membrane, can also be used. Finally, wide bandwidth antennas or arrays can be formed in which the principal direction of radiation is in the plane of the membrane. For this embodiment, the set of elements on the membrane is arranged to form one or more traveling wave antennas. In this case, a nonconductive form of the perimeter springlike material is required to provide the deploying force.

Fink, Patrick W.↗
NASA NTRS2016

DNS of Low-Pressure Turbine Cascade Flows with Elevated Inflow Turbulence Using a Discontinuous-Galerkin Spectral-Element Method

Recent progress towards developing a new computational capability for accurate and efficient high-fidelity direct numerical simulation (DNS) and large-eddy simulation (LES) of turbomachinery is described. This capability is based on an entropy- stable Discontinuous-Galerkin spectral-element approach that extends to arbitrarily high orders of spatial and temporal accuracy, and is implemented in a computationally efficient manner on a modern high performance computer architecture. An inflow turbulence generation procedure based on a linear forcing approach has been incorporated in this framework and DNS conducted to study the effect of inflow turbulence on the suction- side separation bubble in low-pressure turbine (LPT) cascades. The T106 series of airfoil cascades in both lightly (T106A) and highly loaded (T106C) configurations at exit isentropic Reynolds numbers of 60,000 and 80,000, respectively, are considered. The numerical simulations are performed using 8th-order accurate spatial and 4th-order accurate temporal discretization. The changes in separation bubble topology due to elevated inflow turbulence is captured by the present method and the physical mechanisms leading to the changes are explained. The present results are in good agreement with prior numerical simulations but some expected discrepancies with the experimental data for the T106C case are noted and discussed.

Garai, Anirban↗
NASA NTRS2010

Ground and Space Radar Volume Matching and Comparison Software

This software enables easy comparison of ground- and space-based radar observations. The software was initially designed to compare ground radar reflectivity from operational, ground based Sand C-band meteorological radars with comparable measurements from the Tropical Rainfall Measuring Mission (TRMM) satellite s Precipitation Radar (PR) instrument. The software is also applicable to other ground-based and space-based radars. The ground and space radar volume matching and comparison software was developed in response to requirements defined by the Ground Validation System (GVS) of Goddard s Global Precipitation Mission (GPM) project. This software innovation is specifically concerned with simplifying the comparison of ground- and spacebased radar measurements for the purpose of GPM algorithm and data product validation. This software is unique in that it provides an operational environment to routinely create comparison products, and uses a direct geometric approach to derive common volumes of space- and ground-based radar data. In this approach, spatially coincident volumes are defined by the intersection of individual space-based Precipitation Radar rays with the each of the conical elevation sweeps of the ground radar. Thus, the resampled volume elements of the space and ground radar reflectivity can be directly compared to one another.

Morris, Kenneth↗
NASA NTRS2012

In Situ Geochemical Analysis and Age Dating of Rocks Using Laser Ablation-Miniature Mass Spectrometer

A miniaturized instrument for performing chemical and isotopic analysis of rocks has been developed. The rock sample is ablated by a laser and the neutral species produced are analyzed using the JPL-invented miniature mass spectrometer. The direct sampling of neutral ablated material and the simultaneous measurement of all the elemental and isotopic species are the novelties of this method. In this laser ablation-miniature mass spectrometer (LA-MMS) method, the ablated neutral atoms are led into the electron impact ionization source of the MMS, where they are ionized by a 70-eV electron beam. This results in a secondary ion pulse typically 10-100 microsecond wide, compared to the original 5-10-nanosecond laser pulse duration. Ions of different masses are then spatially dispersed along the focal plane of the magnetic sector of the miniature mass spectrometer and measured in parallel by a modified CCD (charge-coupled device) array detector capable of detecting ions directly. Compared to conventional scanning techniques, simultaneous measurement of the ion pulse along the focal plane effectively offers a 100% duty cycle over a wide mass range. LAMMS offers a more quantitative assessment of elemental composition than techniques that detect laser-ionized species produced directly in the ablation process because the latter can be strongly influenced by matrix effects that vary with the structure and geometry of the surface, the laser beam, and the ionization energies of the elements. The measurement of high-precision isotopic ratios and elemental composition of different rock minerals by LAMMS method has been demonstrated. The LA-MMS can be applied for the absolute age determination of rocks. There is no such instrument available presently in a miniaturized version that can be used for NASA space missions. Work is in progress in the laboratory for geochronology of rocks using LA-MMS that is based on K-Ar radiogenic dating technique.

Sinha, Mahadeva P.↗
NASA NTRS2005

A Viable Scheme for Elemental Extraction and Purification Using In-Situ Planetary Resources

NASA's new strategic direction includes establishing a self-sufficient, affordable and safe human and robotic presence outside the low earth orbit. Some of the items required for a self-sufficient extra-terrestrial habitat will include materials for power generation (e.g. Si for solar cells) and habitat construction (e.g. Al, Fe, and Ti). In this paper we will present a viable elemental extraction and refining process from in-situ regolith which would be optimally continuous, robotically automated, and require a minimum amount of astronaut supervision and containment facilities, The approach is based on using a concentrated heat source and translating sample geometry to enable simultaneous oxide reduction and elemental refining. Preliminary results will be presented to demonstrate that the proposed zone refining process is capable of segregating or refining important elements such as Si (for solar cell fabrication) and Fe (for habitat construction). A conceptual scheme will be presented whereby such a process could be supported by use of solar energy and a precursor robotic mission on the surface of the moon.

Sen, S.↗
NASA NTRS1975

Development and testing of a portable wind sensitive directional air sampler

A portable wind sensitive directional air sampler was developed as part of an air pollution source identification system. The system is designed to identify sources of air pollution based on the directional collection of field air samples and their analysis for TSP and trace element characteristics. Sources can be identified by analyzing the data on the basis of pattern recognition concepts. The unit, designated Air Scout, receives wind direction signals from an associated wind vane. Air samples are collected on filter slides using a standard high volume air sampler drawing air through a porting arrangement which tracks the wind direction and permits collection of discrete samples. A preset timer controls the length of time each filter is in the sampling position. At the conclusion of the sampling period a new filter is automatically moved into sampling position displacing the previous filter to a storage compartment. Thus the Air Scout may be set up at a field location, loaded with up to 12 filter slides, and left to acquire air samples automatically, according to the wind, at any timer interval desired from 1 to 30 hours.

Deyo, J.↗
NASA NTRS2018

Görtler Instability and Its Control via Surface Suction over an Axisymmetric Cone at Mach 6

The characteristics of Görtler instability over an axisymmetric cone with an aft concave section are studied via linear and nonlinear instability analysis and direct numerical simulations. Several options for the cone geometry have been investigated numerically, subject to a fixed forecone section and constraints on the maximum cone diameter, overall cone length, and minimum N-factor for the most amplified Görtler modes. Computations show that it is possible to design a cone with a peak N-factor of Nmax > 8 at the target Reynolds number of 12.1×10(exp 6) per meter, corresponding to the maximum quiet Reynolds number in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. Direct numerical simulations show that an array of roughness elements corresponding to a peak roughness height of 0.1006 mm at the center can excite Görtler vortices that evolve into sufficiently strong streamwise streaks that may break down via high-frequency secondary instability. Thus, the selected axisymmetric configuration of interest should provide an acceptable baseline to investigate the feasibility of several aspects of laminar-flow control via boundary-layer suction. The apparatus that is being used for measurements in the Boeing/AFOSR Quiet Tunnel is described, along with some preliminary experimental results.

Gortler vortices↗
NASA NTRS1987

Device Applies Films to Optical Elements

Clamping device applies protective or antireflective dielectric coating to lenses or other optical elements. Alternative version of device applies thin sheet of dielectric film to ring or stretches it for clamping in holder to form pellicle or beam splitter. Defects avoided by new apparatus, which uniformly stretches dielectric films in radial direction and creates vacuum between them before thermally bonded to optical element.

Augason, Gordon C.↗
NASA NTRS1985

Postbuckling analysis using a general purpose code

A new capability for solving postbuckling problems in shell structures is described. The matrix theory to adapt Newton's method to nonlinear finite element shell analysis is outlined first. The matrix theory is directed at writing consistent linear algebratic equations for problems where the tangent stiffness matrix is singular or nearly singular. The matrix theory suggests a change of variables as part of the usual iterative procedure in Newton's method. The change of variables is shown to be feasible for introduction into the algorithm programmed in general purpose codes for finite element analysis of structures. Numerical results from a new option that has been programmed in an existing general purpose code are presented. The analysis of shell structures for collapse and for branching at bifurcation loads is illustrated by the numerical examples.

Thurston, G. A.↗
NASA NTRS1973

BUCLASP 3: A computer program for stresses and buckling of heated composite stiffened panels and other structures, user's manual

The use of the computer program BUCLASP3 is described. The code is intended for thermal stress and instability analyses of structures such as unidirectionally stiffened panels. There are two types of instability analyses that can be effected by PAINT; (1) thermal buckling, and (2) buckling due to a specified inplane biaxial loading. Any structure that has a constant cross section in one direction, that may be idealized as an assemblage of beam elements and laminated flat and curved plate strip-elements can be analyzed. The two parallel ends of the panel must be simply supported, whereas arbitrary elastic boundary conditions may be imposed along any one or both external longitudinal side. Any variation in the temperature rise (from ambient) through the cross section of a panel is considered in the analyses but it must be assumed that in the longitudinal direction the temperature field is constant. Load distributions for the externally applied inplane biaxial loads are similar in nature to the permissible temperature field.

Tripp, L. L.↗
NASA NTRS1989

Skin friction balance

A skin friction balance uses a parallel linkage mechanism to avoid inaccuracies in skin friction measurement attributable to off-center normal forces. The parallel linkage mechanism includes a stationary plate mounted in a cage, and an upper and lower movable plate which are linked to each other and to the stationary plate throught three vertical links. Flexure pivots are provided for pivotally connecting the links and the plates. A sensing element connected to the upper plate moves in response to skin friction, and the lower plate moves in the opposite direction of the upper plate. A force motor maintains a null position of the sensing element by exerting a restoring force in response to a signal generated by a linear variable differential transformer (LVDT).

Ping, Tcheng↗
NASA NTRS1983

Direction of crack growth in fibrous composites

A model for predicting the direction of crack growth in resin matrix composite materials is presented. The model is based upon the normal stress and the anisotropic tensile strength on arbitrary planes about the tip of a crack. The model is incorporated into a finite element solution which predicts energy release rates in addition to the direction of crack growth. Results are obtained for cracks in unidirectional off-axis slotted tensile coupons. Comparisons are made with other theories and experimental results.

Buczek, M. B.↗
NASA NTRS2005

Micromechanics, Fracture Mechanics and Gas Permeability of Composite Laminates for Cryogenic Storage Systems

A micromechanics method is developed to investigate microcrack propagation in a liquid hydrogen composite tank at cryogenic temperature. The unit cell is modeled using square and hexagonal shapes depends on fiber and matrix layout from microscopic images of composite laminates. Periodic boundary conditions are applied to the unit cell. The temperature dependent properties are taken into account in the analysis. The laminate properties estimated by the micromechanics method are compared with empirical solutions using constituent properties. The micro stresses in the fiber and matrix phases based on boundary conditions in laminate level are calculated to predict the formation of microcracks in the matrix. The method is applied to an actual liquid hydrogen storage system. The analysis predicts micro stresses in the matrix phase are large enough to cause microcracks in the composite. Stress singularity of a transverse crack normal to a ply-interface is investigated to predict the fracture behavior at cryogenic conditions using analytical and finite element analysis. When a transverse crack touches a ply-interface of a composite layer with same fiber orientation, the stress singularity is equal to 1/2. When the transverse crack propagates to a stiffer layer normal to the ply-direction, the singularity becomes less than 1/2 and vice versa. Finite element analysis is performed to predict the fracture toughness of a laminated beam subjected to fracture loads measured by four-point bending tests at room and cryogenic temperatures. As results, the fracture load at cryogenic temperature is significantly lower than that at room temperature. However, when thermal stresses are taken into consideration, for both cases of room and cryogenic temperatures, the difference of the fracture toughness becomes insignificant. The result indicates fracture toughness is a characteristic property, which is independent to temperature changes. The experimental analysis is performed to investigate the effect of cryogenic cycling on permeability for various composite material systems. Textile composites have lower permeability than laminated composites even with increasing number of cryogenic cycle. Nano-particles dispersed in laminated composites do not show improvement on permeability. The optical inspection is performed to investigate the microcrack propagation and void content in laminated composites and compared the microscopic results before and after cryogenic cycling.

Choi, Sukjoo↗
NASA NTRS1994

Coronal element abundances derived from solar energetic particles

The large gradual solar-energetic-particle (SEP) events, where abundances are commonly measured, are produced when coronal mass ejections (CMEs) drive shock waves through the corona and the interplanetary medium. The shock accelerates particles from the highly-ionized, approximately 1.5 MK, plasma in a manner that depends only weakly upon the Q/A of the ion, except at very high energies. Averaging the approximately 1 MeV/amu abundances over many events compensates for the acceleration effects to produce abundances that appear to correspond directly to those in the coronal source for all observed elements, including H. The resulting abundances reflect the 4 x enhancement of ions with low values of first ionization potential (FIP) arising from ion-neutral fractionation that occurs as the atoms are transported up from the photosphere. A different pattern of fractionation is found for ions that are shock-accelerated from the high speed solar wind emerging from coronal holes.

Reames, Donald V.↗
NASA NTRS2018

Auto Tracking Antenna Platform

The present invention is an auto tracking antenna platform upon which multiple antenna elements can be mounted to track a common moving object. The antenna tracking platform generally comprises a bottom pedestal enclosing a rotary azimuth actuator for controlled-rotary motion about the single vertical (z) axis, and an upper multi-tier framework housing a horizontal antenna-mounting beam pivotally supported for rotation about a horizontal (x) axis, and a drive assembly for direct-drive rotation of the antenna-mounting bar. Antenna elements are mounted along the horizontal mounting bar and the feeds routed through the azimuth actuator. This enables the use of fiber optic rotary joints or slip rings to pass data and video, instead of RF (waveguide) rotary joints which are required to pass high power RF signals.

Sanner, Kurt G↗
NASA NTRS2014

Path Toward a Unifid Geometry for Radiation Transport

The Direct Accelerated Geometry for Radiation Analysis and Design (DAGRAD) element of the RadWorks Project under Advanced Exploration Systems (AES) within the Space Technology Mission Directorate (STMD) of NASA will enable new designs and concepts of operation for radiation risk assessment, mitigation and protection. This element is designed to produce a solution that will allow NASA to calculate the transport of space radiation through complex computer-aided design (CAD) models using the state-of-the-art analytic and Monte Carlo radiation transport codes. Due to the inherent hazard of astronaut and spacecraft exposure to ionizing radiation in low-Earth orbit (LEO) or in deep space, risk analyses must be performed for all crew vehicles and habitats. Incorporating these analyses into the design process can minimize the mass needed solely for radiation protection. Transport of the radiation fields as they pass through shielding and body materials can be simulated using Monte Carlo techniques or described by the Boltzmann equation, which is obtained by balancing changes in particle fluxes as they traverse a small volume of material with the gains and losses caused by atomic and nuclear collisions. Deterministic codes that solve the Boltzmann transport equation, such as HZETRN [high charge and energy transport code developed by NASA Langley Research Center (LaRC)], are generally computationally faster than Monte Carlo codes such as FLUKA, GEANT4, MCNP(X) or PHITS; however, they are currently limited to transport in one dimension, which poorly represents the secondary light ion and neutron radiation fields. NASA currently uses HZETRN space radiation transport software, both because it is computationally efficient and because proven methods have been developed for using this software to analyze complex geometries. Although Monte Carlo codes describe the relevant physics in a fully three-dimensional manner, their computational costs have thus far prevented their widespread use for analysis of complex CAD models, leading to the creation and maintenance of toolkit-specific simplistic geometry models. The work presented here builds on the Direct Accelerated Geometry Monte Carlo (DAGMC) toolkit developed for use with the Monte Carlo N-Particle (MCNP) transport code. The workflow for achieving radiation transport on CAD models using MCNP and FLUKA has been demonstrated and the results of analyses on realistic spacecraft/habitats will be presented. Future work is planned that will further automate this process and enable the use of multiple radiation transport codes on identical geometry models imported from CAD. This effort will enhance the modeling tools used by NASA to accurately evaluate the astronaut space radiation risk and accurately determine the protection provided by as-designed exploration mission vehicles and habitats

Lee, Kerry↗