Search NASA⌕ Search

SEARCH · Search NASA

Results for “engine friction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Atomistic observation on diffusion-mediated friction between single-asperity contacts

Super-lubricity, a sliding regime in which friction almost vanishes, has been well-documented with the advent of atomic force microscopy (AFM) and molecular dynamics (MD) simulation due to its enormous implications for manufacturing micro-/nano-electromechanical systems (MEMS/NEMS). Nevertheless, the atomistic mechanisms for super-lubricious behaviors are still elusive, primarily due to a lack of direct observation of interface at atomic resolution during frictional process. Here by using in situ high-resolution transmission electron microscopy (HRTEM) coupled with AFM, we report diffusion-mediated formation of a loosely-packed interfacial layer between two metallic asperities at infinitesimal normal forces, which is responsible for the sliding regime, super-lubricity exhibiting ultra-low friction forces and continuous sliding. By contrast, the loosely-packed interfacial layer vanishes along with the super-lubricity, leading to typical stick-slip friction. Additionally, in situ TEM observation and MD simulations reveals the crucial role that atom diffusion plays in atomic friction, and provides new insights into the fundamental mechanisms of super-lubricity.

42 ENGINEERING↗

Roller Sliding in Wind Turbine Gearbox High-Speed-Shaft Bearings

Failures in gearbox bearings have been a primary source of reliability issues for wind turbine drivetrains, leading to costly downtime and unplanned maintenance. The most common failure mode is attributed to so-called white-etching cracks (WECs). This mode of failure can occur at 5%-20% of the predicted design life and has been observed in many other industries, bearing locations, bearing types, bearing parts, and steel types. The main drivers for the creation of WECs in steel specimens have been identified and verified by material testing. In a full-scale wind turbine gearbox, however, the conditions leading to WECs, the process by which this failure culminates, and the reasons for their apparent prevalence are all still highly debated. In a collaborative project, Flender Corporation, SKF and the National Renewable Energy Laboratory have instrumented a commercial drivetrain, installed it in a wind turbine, and operated the turbine for over a year. In this report, these measurements are used to validate two different modelling approaches for bearing sliding, one analytical dynamic model and one multi-body model. Once validated, these models can then be used to evaluate the roller slip losses or cumulative frictional energy that are each considered as potential driving factors for wind turbine gearbox bearing failures by WEC.

17 WIND ENERGY↗

Recent developments in flutter suppression techniques for turbomachinery rotors

Recent research on passive flutter control techniques for rotors and cascades is reviewed. The proposed methods include the use of periodicity-breaking inperfections, aeroelastic tailoring, dry friction damping, and mode shape control. Numerical results are presented to illustrate the effectiveness of each method in controlling various types of flutter, and to evaluate the feasibility of incorporating the techniques in current and future technology rotors. Mistuning may be the only feasible approach for existing engines, but aeroelastic tailoring offers promising advantages for future engines.

Bendiksen, O. O.↗

A method for landing gear modeling and simulation with experimental validation

This document presents an approach for modeling and simulating landing gear systems. Specifically, a nonlinear model of an A-6 Intruder Main Gear is developed, simulated, and validated against static and dynamic test data. This model includes nonlinear effects such as a polytropic gas model, velocity squared damping, a geometry governed model for the discharge coefficients, stick-slip friction effects and a nonlinear tire spring and damping model. An Adams-Moulton predictor corrector was used to integrate the equations of motion until a discontinuity caused by a stick-slip friction model was reached, at which point, a Runga-Kutta routine integrated past the discontinuity and returned the problem solution back to the predictor corrector. Run times of this software are around 2 mins. per 1 sec. of simulation under dynamic circumstances. To validate the model, engineers at the Aircraft Landing Dynamics facilities at NASA Langley Research Center installed one A-6 main gear on a drop carriage and used a hydraulic shaker table to provide simulated runway inputs to the gear. Model parameters were tuned to produce excellent agreement for many cases.

Daniels, James N.↗

Flowability of JSC-1a

We have done a complete flowability characterization of the lunar soil simulant, JSC-1a, following closely the ASTM-6773 standard for the Schulze ring shear test. The measurements, which involve pre-shearing the material before each yield point, show JSC-1a to be cohesionless, with an angle of internal friction near 40 deg. We also measured yield loci after consolidating the material in a vibration table which show it to have significant cohesion (approximately equal to 1 kPa) and an angle of internal friction of about 60 deg. Hopper designs based on each type of flowability test differ significantly. These differences highlight the need to discern the condition of the lunar soil in the specific process where flowability is an issue. We close with a list not necessarily comprehensive of engineering rules of thumb that apply to powder flow in hoppers.

Rame, Enrique↗

The Influence of Friction Stir Weld Tool Form and Welding Parameters on Weld Structure and Properties: Nugget Bulge in Self-Reacting Friction Stir Welds

Although friction stir welding (FSW) was patented in 1991, process development has been based upon trial and error and the literature still exhibits little understanding of the mechanisms determining weld structure and properties. New concepts emerging from a better understanding of these mechanisms enhance the ability of FSW engineers to think about the FSW process in new ways, inevitably leading to advances in the technology. A kinematic approach in which the FSW flow process is decomposed into several simple flow components has been found to explain the basic structural features of FSW welds and to relate them to tool geometry and process parameters. Using this modelling approach, this study reports on a correlation between the features of the weld nugget, process parameters, weld tool geometry, and weld strength. This correlation presents a way to select process parameters for a given tool geometry so as to optimize weld strength. It also provides clues that may ultimately explain why the weld strength varies within the sample population.

Schneider, Judy↗

Flight Performance and Stability of Space Launch System Core Stage Thrust Vector Control

The Space Launch System (SLS) Core Stage (CS) Thrust Vector Control (TVC) system is comprised of eight mechanical feedback Shuttle heritage Type III TVC actuators and four RS-25 engines, each attached to a Shuttle heritage gimbal block/bearing. The Core Stage TVC shares vehicle control authority with the SLS 5-segment Solid Rocket Boosters (SRBs) during boost phase flight, and is the sole means of vehicle flight control during in exoatmospheric flight following SRB separation. TVC responses during Green Run Hot Fire (GRHF) testing revealed that the TVC did not meet its performance specifications. Step and frequency responses exhibited unexpected departures from prior laboratory data and modeled behavior. Post-test analysis determined that the characteristics of the structure and gimbal friction are significantly influenced by the thrust-loaded conditions, and the command avionics exhibited a small but important gain nonlinearity. Using the available test data, the design team augmented the flight control TVC models to bound the observed results and include the additional fidelity needed for vehicle flight control analysis so as to build sufficient rationale for flight certification. Prior to the Green Run tests, “simplex” linear models typically used for flight control analysis did not include gimbal friction and other nonlinearities owing to long-standing assumptions that these effects were negligible in the Shuttle Orbiter TVC system. Following the Green Run findings, simulation analysis of the flight dynamics in the time and frequency domain revealed the propensity for a flight control limit cycle oscillation (LCO) if friction and structural compliances fell near the edges of test-predicted bounds. While the “most probable” models did not predict an in-flight LCO, the SLS Program conservatively proceeded with a system-wide evaluation and ultimate acceptance of the possibility for a small amplitude, low-frequency TVC LCO in flight. A final validation of the extensive test and modeling effort occurred when the first flight of SLS successfully demonstrated the fully integrated performance of the vehicle’s TVC system This paper is the final installment in a seven-paper series surveying the design, engineering, test validation, and flight performance of the Core Stage Thrust Vector Control system. In this paper, the development of flight rationale in light of the TVC responses observed in Green Run is discussed, along with a review of the flight telemetry illustrating the correlation of the preflight predictions with the observed performance.

John H. Wall↗

A moment-based kinetic theory model for polydisperse gas–particle flows

Starting from a generalized population balance equation and the Boltzmann–Enskog collision model for hard spheres, a kinetic theory model for polydisperse gas–particle flows is introduced. Here, polydispersity results from spherical particles with the same material density but different diameters. The particle size distribution (PSD) of the particles is allowed to evolve in space and time due to physical processes such as mixing. In order to treat a continuous PSD, the particle-phase model is formulated in terms of the moments of the PSD, and velocity moments conditioned on the particle size. Velocity moments up to second order are included, resulting in transport equations for the mass, momentum and granular temperature, all conditioned on the particle size. In the numerical implementation, the PSD is represented using quadrature-based moment methods (QBMM). With QBMM, a continuous PSD can be treated using a relatively small number of moments as compared to class or sectional methods. In this work, a realizable numerical algorithm for solving the moment system in a finite-volume code is proposed, valid for dilute systems wherein frictional forces are negligible. The ability of the proposed model to describe polydisperse gas–particle systems is demonstrated using cluster-induced turbulence and riser flow.

42 ENGINEERING↗

Development of Seismic Isolation Systems Using Periodic Materials

Advanced fast nuclear power plants and small modular fast reactors are composed of thin-walled structures such as pipes; as a result, they do not have sufficient inherent strength to resist seismic loads. Seismic isolation, therefore, is an effective solution for mitigating earthquake hazards for these types of structures. Base isolation, on which numerous studies have been conducted, is a well-defined structure protection system against earthquakes. In conventional isolators, such as high-damping rubber bearings, lead-rubber bearings, and friction pendulum bearings, large relative displacements occur between upper structures and foundations. Only isolation in a horizontal direction is provided; these features are not desirable for the piping systems. The concept of periodic materials, based on the theory of solid-state physics, can be applied to earthquake engineering. The periodic material is a material that possesses distinct characteristics that prevent waves with certain frequencies from being transmitted through it; therefore, this material can be used in structural foundations to block unwanted seismic waves with certain frequencies. The frequency band of periodic material that can filter out waves is called the band gap, and the structural foundation made of periodic material is referred to as the periodic foundation. The design of a nuclear power plant, therefore, can be unified around the desirable feature of a periodic foundation, while the continuous maintenance of the structure is not needed. In this research project, three different types of periodic foundations were studied: one-dimensional, two-dimensional, and three-dimensional. The basic theories of periodic foundations are introduced first to find the band gaps; then the finite element methods are used, to perform parametric analysis, and obtain attenuation zones; finally, experimental programs are conducted, and the test data are analyzed to verify the theory. This procedure shows that the periodic foundation is a promising and effective way to mitigate structural damage caused by earthquake excitation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Hot piston ring tests

As part of the DOE/NASA Automotive Stirling Engine Project, tests were made at NASA Lewis Research Center to determine whether appendix gap losses could be reduced and Stirling engine performance increased by installing an additional piston ring near the top of each piston dome. An MTI-designed upgraded Mod I Automotive Stirling Engine was used. Unlike the conventional rings at the bottom of the piston, these hot rings operated in a high temperature environment (700 C). They were made of a high temperature alloy (Stellite 6B) and a high temperature solid lubricant coating (NASA Lewis-developed PS-200) was applied to the cylinder walls. Engine tests were run at 5, 10, and 15 MPa operating pressure over a range of operating speeds. Tests were run both with hot rings and without to provide a baseline for comparison. Minimum data to assess the potential of both the hot rings and high temperature low friction coating was obtained. Results indicated a slight increase in power and efficiency, an increase over and above the friction loss introduced by the hot rings. Seal leakage measurements showed a significant reduction. Wear on both rings and coating was low.

Allen, David J.↗

Friction And Wear Of Silicon Ceramics

Report presents results of experimental study of friction and wear in unlubricated sliding of silicon-based ceramics on Inconel(R) 718 nickel-based alloy. Both monolithic and fiber-reinforced ceramics tested at temperatures from 25 to 800 degrees C. Evaluates ceramic materials for potential use as cylinder liners, piston caps, and other engine parts subjected to sliding or rubbing.

Deadmore, Daniel L.↗

Survey of the Relationship Between Theory and Experiment for Convective Heat Transfer From Rocket Combustion Gases

The problem of predicting the distribution of heat flux in a rocket engine is complicated by a flow field and thermodynamics so perturbed by as yet indescribable combustion effects that it continues to be necessary to utilize a simplified theoretical model against which to compare experimental results in order to gain insight. The most successful model applied to this problem is that of a compressible, turbulent, accelerating boundary layer flow with an arbitrary point of origin, and chemical reaction restricted to equilibrium recombination or diffusion-limited recombination on a catalytic wall. Analysis of this model was not possible without making several assumptions about the nature of the skin friction coefficient relationship and Reynold's analogy in an accelerating boundary layer flow. The paper summarizes the analysis of this model (together with detailed treatment of the special problems of variable properties, chemical reaction, and sources of transport properties), and describes several closed-form equations that have also been developed and applied to the problem. Described are results of several experiments with hot air flow made for the purpose of checking the validity of the assumptions in the boundary layer analysis. Most significant, however, are presentations of sample distributions of local heat flux measured in rocket engines operating with a wide range of conditions, propellants, injectors and sizes. When compared with predictions, these data show the significant range of deviation in heat flux that results from the combustion effects and which precludes a generally accurate prediction theory or correlation equation until the combustion process itself is correlated.

D R Bartz↗

Microstructural Engineering of Cu-Rich Nanoprecipitate formation in NiCoFeCrCu0.12 High-Entropy Alloy via Severe Plastic Deformation for Enhanced Irradiation Tolerance

This study demonstrates a defect-engineering approach for controlling Cu-rich precipitates in FeNiCrCoCu0.2 high-entropy alloys (Cu-HEAs), delivering a novel pathway for next-generation nuclear reactor materials with superior irradiation resistance. This work establishes that severe plastic deformation (SPD) processing via Shear Assisted Processing and Extrusion (ShAPE) and Friction Stir Layer Deposition (FSLD) creates dense dislocation networks and subgrain boundaries that fundamentally alter precipitation behavior under identical thermal treatments. Atom probe tomography (APT) indicates that SPD produces a metastable, atomically homogeneous solid solution that, upon moderate heat treatment (500°C/10 hour), develops remarkedly stronger Cu clustering than the as-cast counterpart. High-temperature exposure (800°C/100 h) produces near-pure Cu precipitates (~90 at% Cu) with significantly enhanced defect-sink efficacy in SPD-processed alloys: precipitate sizes of 50-60 nm and number densities of 2.7-3.8 × 10¹7 m?³, compared to 89 nm and 0.44 × 10¹7 m?³ in as-cast materials. Collectively, the findings establish defect-mediated precipitation control as a scalable, high-impact route to tailor sink density and distribution in HEAs, enabling microstructures optimized for irradiation tolerance and mechanical robustness in nuclear reactor environments.

Meher, Subhashish↗

Support services for the automative gas turbine project

Support was provided to DOE and NASA in their efforts to inform industry, the public, and Government on the benefits and purpose of the gas turbine programs through demonstrations and exhibits. Tasks were carried out for maintenance, repair, and retrofit of the experimental gas turbine engines being used by NASA in their gas turbine technology programs and in program demonstrations. Limited support testing was conducted at Chrysler in which data were generated on air bearing rotor shaft dynamics, heavy duty variable sheave rubber belts, high temperature elastomer regenerator drive mounting and graphite regenerator seal friction characteristics.

Golec, T.↗

Rotordynamics

Research activities that can ultimately lead to optimum rotordynamics design for the space shuttle main engine are outlined. Achievements are summarized in: (1) improving analysis and simulation techniques; (2) defining forces which result from the rotor and surroundings; (3) determining the effect of rubbing; (4) improving balancing; (5) developing damping methods, i.e., eddy-current and damping seals; (6) establishing methods to quantify internal friction; and (7) developing supporting test apparatus.

Schutzenhofer, L. A.↗

Tribological Behavior of a Cr{sub 2}O{sub 3} Ceramic Coating/Steel Couple Under Dry Sliding and Heavy Loading Conditions

This work evaluates the effects of heavy loadings on a Cr{sub 2}O{sub 3} ceramic coating/steel couple under dry sliding and in conditions similar to those occurring in heavy-duty diesel engines. Two types of wear tests were performed by a standard pin-on-disc tribometer under high constant and variable loads. Before wear tests, microstructure and mechanical properties of coating and steel were determined by optical emission spectrometry, optical microscopy, roughness, microhardness and x-ray diffractometry (XRD). The friction coefficient was directly calculated by the tribometer. The wear rate of Cr{sub 2}O{sub 3} ceramic coating was evaluated by the wear volume and that of pins by weighing them before and after tests. The wear tracks on pins and coating surfaces were analyzed by XRD and by scanning electron microscopy with energy-dispersive spectroscopy. For all loads except the lowest constant one, the results indicated high friction and wear involving material removal from the coating surface, through a severe-oxidational wear associated with extensive cracking of the surface of the coating, softening of the carburizing steel and removal of the carburized layer of pins. The wear mechanism was mild-oxidational under the lowest constant load, which was therefore suggested as the limit for acceptable performance of the sliding couple under study.

36 MATERIALS SCIENCE↗

Selection of burn-resistant materials for oxygen-driven turbopumps

NASA goals for reusable space-based, high-performance orbit transfer vehicle propulsion systems have resulted in a need for oxygen/hydrogen engines which include lightweight, highly reliable, liquid oxygen pumps. The selection of ignition- and burn-resistant materials is a major factor in the design of a compact 75,000-rpm turbopump which can deliver 6 lbM/sec of liquid oxygen at 5,000 psia. The potential operational hazards of rubbing friction and impact of foreign particles at high velocity were investigated experimentally for a wide range of candidate materials, i.e., nickel, copper, monel, 316 Stainless Steel, Hastelloy-X, Invar-36, and silicon carbide. Test parameters included oxygen pressure and temperature up to 5,000 psia and 800 F, respectively. The effect of increasing the O2 pressure from 1000 to 5000 psi is discussed. The applicability of the candidate materials to oxygen pump design was ranked by comparing the experimental results among themselves and with an analytically determined parameter, i.e., the burn factor. Nickel and copper demonstrated superior resistance to ignition and burn in the friction rubbing and particle impact tests relative to monel, stainless steel, and nickel-iron base superalloys.

Schoenman, L.↗

Fretting Stresses in Single Crystal Superalloy Turbine Blade Attachments

Single crystal nickel base superalloy turbine blades are being utilized in rocket engine turbopumps and turbine engines because of their superior creep, stress rupture, melt resistance and thermomechanical fatigue capabilities over polycrystalline alloys. Currently the most widely used single crystal nickel base turbine blade superalloys are PWA 1480/1493 and PWA 1484. These alloys play an important role in commercial, military and space propulsion systems. High Cycle Fatigue (HCF) induced failures in aircraft gas turbine and rocket engine turbopump blades is a pervasive problem. Blade attachment regions are prone to fretting fatigue failures. Single crystal nickel base superalloy turbine blades are especially prone to fretting damage because the subsurface shear stresses induced by fretting action at the attachment regions can result in crystallographic initiation and crack growth along octahedral planes. Furthermore, crystallographic crack growth on octahedral planes under fretting induced mixed mode loading can be an order of magnitude faster than under pure mode I loading. This paper presents contact stress evaluation in the attachment region for single crystal turbine blades used in the NASA alternate Advanced High Pressure Fuel Turbo Pump (HPFTP/AT) for the Space Shuttle Main Engine (SSME). Single crystal materials have highly orthotropic properties making the position of the crystal lattice relative to the part geometry a significant factor in the overall analysis. Blades and the attachment region are modeled using a large-scale 3D finite element (FE) model capable of accounting for contact friction, material orthotrophy, and variation in primary and secondary crystal orientation. Contact stress analysis in the blade attachment regions is presented as a function of coefficient of friction and primary and secondary crystal orientation, Stress results are used to discuss fretting fatigue failure analysis of SSME blades. Attachment stresses are seen to reach peak values at locations where fretting cracks have been observed. Fretting stresses at the attachment region are seen to vary significantly as a function of crystal orientation. Attempts to adapt techniques used for estimating fatigue life in the airfoil region, for life calculations in the attachment region, are presented. An effective model for predicting crystallographic crack initiation under mixed mode loading is required for life prediction under fretting action.

Arakere, Nagaraj K.↗