Search NASA⌕ Search

SEARCH · Search NASA

Results for “friction experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Wall-modeled LES of the Three-dimensional Speed Bump Experiment

We evaluate the performance of wall-modeled large eddy simulation (WMLES) in predicting smooth-body turbulent flow separation for a three-dimensional Gaussian-shaped speed bump geometry. The Reynolds number based on the bump length is 2 million, and an unstructured compressible finite-volume solver is used with an equilibrium wall model and dynamic subgrid scale model. Spanwise periodic simulations of the centerline two-dimensional bump were used to assess grid resolution requirements, and resolving the thin internal layer in the accelerating region was found to be necessary to correctly capture the downstream separated flow region. Based on these insights, an optimized grid that was smaller by a factor of two provided comparable accuracy to a finer grid that has been used by us and other researchers in past studies. Using insights gained from the spanwise periodic simulation, an unstructured polyhderal grid with about 250 million cells was used for the three-dimensional (3D) configuration with inviscid tunnel side and top walls. Detailed comparisons of wall skin-friction coefficient, wall pressure, velocity and turbulent stresses with available experimental data indicated excellent agreement. While the low-Reynolds Number Spalart-Allmaras RANS model with rotation/curvature correction gave qualitatively good agreement with experiments, WMLES showed significantly more accurate quantitative predictions of the flowfield. The 3D WMLES showed good agreement with experiments in the separated region, and the centerplane results indicated a different separation topology compared to the spanwise periodic simulation.

Computational Fluid Dynamics↗

Bi-directional, buried-wire skin-friction gage

A compact, nonobtrusive, bi-directional, skin-friction gage was developed to measure the mean shear stress beneath a three-dimensional boundary layer. The gage works by measuring the heat flux from two orthogonal wires embedded in the surface. Such a gage was constructed and its characteristics were determined for different angles of yaw in a calibration experiment in subsonic flow with a Preston tube used as a standard. Sample gages were then used in a fully three-dimensional turbulent boundary layer on a circular cone at high relative incidence, where there were regimes of favorable and adverse pressure gradients and three-dimensional separation. Both the direction and magnitude of skin friction were then obtained on the cone surface.

Higuchi, H.↗

Quasi-one-dimensional compressible flow across face seals and narrow slots. 1: Analysis

An analysis is presented for compressible fluid flow across shaft face seals and narrow slots. The analysis includes fluid inertia, viscous friction, and entrance losses. Subsonic and choked flow conditions can be predicted and analyzed. The model is valid for both laminar and turbulent flows. Results agree with experiment and with solutions which are more limited in applicability. Results show that a parallel film can have a positive film stiffness under choked flow conditions.

Zuk, J.↗

SSME blade damper technology

Before 1975 turbine blade damper designs were based on experience and very simple mathematical models. Failure of the dampers to perform as expected showed the need to gain a better understanding of the physical mechanism of friction dampers. Over the last 10 years research on friction dampers for aeronautical propulsion systems has resulted in methods to optimize damper designs. The first-stage turbine blades on the Space Shuttle Main Engine (SSME) high-pressure oxygen pump have experienced cracking problems due to excessive vibration. A solution is to incorporate a well-designed friction dampers to attenuate blade vibration. The subject study, a cooperative effort between NASA Lewis and Carnegie-Mellon University, represents an application of recently developed friction damper technology to the SSME high-pressure oxygen turbopump. The major emphasis was the contractor's design known as the two-piece damper. Damping occurs at the frictional interface between the top half of the damper and the underside of the platforms of the adjacent blades. The lower half of the damper is an air seal to retard airflow in the volume between blade necks.

Kielb, Robert E.↗

Penetrator Coring Apparatus for Cometary Surfaces

Touch and go impact coring is an attractive technique for sampling cometary nuclei and asteroidal surface on account of the uncertain strength properties and low surface gravities of these objects. Initial coring experiments in low temperature (approx. 153K polycrystalline ice) and porous rock demonstrate that simultaneous with impact coring, measurements of both the penetration strength and constraints on the frictional properties of surface materials can be obtained upon core penetration and core sample extraction. The method of sampling an asteroid, to be deployed, on the now launched MUSES-C mission, employs a small gun device that fires into the asteroid and the resulted impact ejecta is collected for return to Earth. This technique is well suited for initial sampling in a very low gravity environment and deployment depends little on asteroid surface mechanical properties. Since both asteroids and comets are believed to have altered surface properties a simple sampling apparatus that preserves stratigraphic information, such as impact coring is an attractive alternate to impact ejecta collection.

Braun, David F.↗

Evaporation heat transfer and friction characteristics of R-134a flowing downward in a vertical corrugated tube

Differently from most previous studies, the heat transfer and friction characteristics of the pure refrigerant HFC-134a during evaporation inside a vertical corrugated tube are experimentally investigated. The double tube test sections are 0.5 m long with refrigerant flowing in the inner tube and heating water flowing in the annulus. The inner tubes are one smooth tube and two corrugated tubes, which are constructed from smooth copper tube of 8.7 mm inner diameter. The test runs are performed at evaporating temperatures of 10, 15, and 20 C, heat fluxes of 20, 25, and 30 kW/m{sup 2}, and mass fluxes of 200, 300, and 400 kg/m{sup 2} s. The quality of the refrigerant in the test section is calculated using the temperature and pressure obtained from the experiment. The pressure drop across the test section is measured directly by a differential pressure transducer. The effects of heat flux, mass flux, and evaporation temperature on the heat transfer coefficient and two-phase friction factor are also discussed. It is found that the percentage increases of the heat transfer coefficient and the two-phase friction factor of the corrugated tubes compared with those of the smooth tube are approximately 0-10% and 70-140%, respectively. (author)

42 ENGINEERING↗

"Coulombic Viscosity" In Granular Materials: Planetary and Astrophysical Implications

The term "Coulombic viscosity" is introduced here to define an empirically observed phenomenon from experiments conducted in both microgravity, and in ground-based 1-g conditions. In the latter case, a sand attrition device was employed to test the longevity of aeolian materials by creating two intersecting grain-circulation paths or cells that would lead to most of the grain energy being expended on grain-to-grain collisions (simulating dune systems). In the areas in the device where gravitationally-driven grain-slurries recycled the sand, the slurries moved with a boundary-layer impeded motion down the chamber walls. Excessive electrostatic charging of the grains during these experiments was prevented by the use of an a.c. corona (created by a Tesla coil) through which the grains passed on every cycle. This created both positive and negative ions which neutralized the triboelectrically-generated grain charges. When the corona was switched on, the velocity of the wall-attached slurries increased by a factor of two as approximately determined by direct observation. What appeared to be a freely-flowing slurry of grains impeded only by intergranular mechanical friction, had obviously been significantly retarded in its motion by electrostatic forces between the grains; with the charging reduced, the grains were able to move past one another without a flow "viscosity" imposed by the Coulombic intergranular forces. A similar phenomenon was observed during microgravity experiments aboard Space Shuttle in USML-1 & USML-2 spacelabs where freely-suspended clouds of sand were being investigated for their potential to for-m aggregates. In this environment, the grains were also charged electrostatically (by natural processes prior to flight), but were free from the intervention of gravity in their interactions. The grains were dispersed into dense clouds by bursts of air turbulence and allowed to form aggregates as the ballistic and turbulent motions damped out. During this very brief (30-60 sec) damping period, motion of the grains was observed to be retarded by the electrostatic interactions. The fact that the grains almost instantly formed aggregates was evidence that their ballistic motions had been constrained and redirected by the dipole-dipole interactions that led to filamentary aggregate development. Undoubtedly, the "Coulombic viscosity" of the cloud assisted in damping grain motion so rapidly. The electrostatically-induced grain-cloud viscosity or drag exerted on grain motion, is a complex function of three major parameters: charge magnitude, charge sign, and mean intergranular distance. The above experiments illustrate one particular type of granular behavior. The discussion here will therefore be restricted to drag relationships: (a) between grains that are naturally charged triboelectrically and thus exhibit dipole-dipole attractions between one another even if there are slight net charges present (which can be overwhelmed by dipole coupling at short distances), and (b) between grains that are densely spaced where the intergranular distance varies between zero and some value (usually tens or hundreds of grain diameters) that permits each grain to detect the dipole moment of another grain -- the distance is not so great that other grains appears as neutral electrical "singularities. I. Aeolian transport: During motion of grains in a saltation cloud (on Earth, Mars, or Venus), triboelectric charging must occur as a result of multiple grain contacts, and by friction with the entraining air. A situation might develop that is similar to the one described above in the attrition device: grain motion becoming significantly retarded (reduced flux) as grains find it increasingly difficult to either separate from the surface, or to pass one another without Coulombic retarding forces. A "Coulombic drag" will exist at flux initiation and increase with time to work in direct opposition to the aerodynamic drag that drives the grain motion. It is predicted that this will lead to an increase with time of both the aerodynamic and bed-dilatancy thresholds (3). Because of Paschen discharge effects in the martian atmosphere, the electrostatic charging in a saltation cloud may be partially abated, but this will lead to greater grain mobility, more charging, and thus to a charge-discharge steady state mediated by mechanical interactions. II. Dry colluvial systems: Sand avalanches on dunes, dry debris flows, talus flows, avalanches, and pyroclastic surges are examples of gravity-driven, dense granular flows where rock/grain fragmentation and grain-to-grain interactions cause triboelectrification (sometimes augmented by other electrical charging processes), and where the grain densities of the systems are such that strong dipole-dipole interactions between grains might be expected to be present. Because it is expected that the Coulombic forces between grains will cause a sluggishness or enhanced granular-flow viscosity, the motion of a grain mass will be retarded or damped so that this will assist, ultimately, in terminating the flow. The greatest Coulombic viscosity will be created in the most highly charged systems, which will also be the most energetic. Thus, grain flows have some tendency to be self-limiting by internal energy partitioning; gravitational potential is converted to Coulombic potential, which manifests itself as a drag force between the grains. III. Volcanic eruption plumes and impact ejecta curtains: The violence of these systems leads to powerful electrical charging of particulates. Lightning storms emanating from volcanic plumes are a testimony to the levels of charging. As pyroclastic grains interact forcefully and frequently within eruption plumes, it is reasonable to predict that the internal turbulent motions of the plume will be significantly damped by the Coulombic viscosity exerted by grain charges. Additional information is contained in the original.

Marshall, J. R.↗

Dynamic behavior of the mercury damper

The dynamic behavior of the mercury nutation damper is investigated. Particular attention is paid to the eccentric annular mercury configuration, which is the final continuous ring phase that occurs in the operation of all mercury dampers. In this phase, damping is poorest, and the system is closely linear. During the investigation, the hydrodynamic problem is treated as three dimensional, and extensive use is made of a variational principle of least-viscous frictional power loss. A variational principle of least-constraint is also used to advantage. Formulas for calculating the behavior of the mercury damper are obtained. Some confirmatory experiments were performed with transparent ring channels on a laboratory gyroscope. Selected movie frames taken during wobble damping are shown along with the results of film measurements.

Crout, P. D.↗

Comparison of Several Different Sputtered Molybdenum Disulfide Coatings for Use in Space Applications

Tribology experiments on different types of sputtered molybdenum disulfide (MoS2) coatings (obtained from different vendors) using accelerated testing techniques were conducted. The purpose was to determine which would be the best coating for use with auxiliary journal bearings for spacecraft energy storage flywheels. Experiments were conducted in moist air (50% relative humidity) and in dry air (<100 PPM water vapor content) on a Pin-on-Disk Tribometer to determine how well the coatings would perform in air. Experiments were also conducted on a Block-on-Ring Tribometer in dry nitrogen (<100 PPM water vapor) to simulate how well the coatings would perform in vacuum. Friction, counterface wear, coating wear, endurance life and surface morphology were investigated.

Fusaro, Robert L.↗

Electrostatic Regolith Interaction Experiment (ERIE) Electrometer Initial Flight Results

The Electrostatic Regolith Interaction Experiment (ERIE) is a suborbital flight payload studying electrostatically charged dust particle dynamics under microgravity, jointly developed by University of Central Florida (UCF) and NASA Kennedy Space Center (KSC). ERIE combines components from two systems, the COLLisions Into Dust Experiment (COLLIDE) from UCF and the Wheel Electrostatic Spectrometer (WES) from NASA KSC, to advance understanding of charged grain behavior on low gravity bodies such as the Moon and asteroids. ERIE slides a door containing an electrometer system monitoring various insulating disks across the surface of a regolith simulant bed. The experiment is activated when the payload enters the microgravity potion of the flight. The grains in the simulant bed tribocharge via agitation during launch as well as through frictional interactions with the door and its protruding insulators. As the retention door retracts, particles are allowed to loft into an open volume, achieving motion due to electrostatic repulsion. The electrometer system measures the charge transfer between the granular material and the insulators. As the charged grains exit the bed, they travel through an applied electric field and a camera observes the kinematics of the individual grains whose trajectories are determined by their net charges. The design of the ERIE electrometer instrument and initial results from the first flight was presented at the 2021 AGU Fall Meeting under P55E-2002. Shortly after microgravity was achieved and the retaining door began to open, the rate of charge acquisition measured by the electrometer increased, indicating the insulators were accumulating triboelectric charge. Charged grains were observed in the video data to traverse across the external electric field and become deflected from a linear path due to their charges. Pairs of grains were also observed to orbit one another as expected from two oppositely charged bodies in proximity to one another. Improvements to the design of the instrument and preliminary results obtained from the second flight scheduled for Q3 2022 will be presented at this meeting.

Electrostatics↗

Electrostatic Regolith Interaction Experiment (ERIE) Electrometer Initial Flight Results

The Electrostatic Regolith Interaction Experiment (ERIE) is a suborbital flight payload studying electrostatically charged dust particle dynamics under microgravity, jointly developed by University of Central Florida (UCF) and NASA Kennedy Space Center (KSC). ERIE combines components from two systems, the COLLisions Into Dust Experiment (COLLIDE) from UCF and the Wheel Electrostatic Spectrometer (WES) from NASA KSC, to advance understanding of charged grain behavior on low gravity bodies such as the Moon and asteroids. ERIE slides a door containing an electrometer system monitoring various insulating disks across the surface of a regolith simulant bed. The experiment is activated when the payload enters the microgravity potion of the flight. The grains in the simulant bed tribocharge via agitation during launch as well as through frictional interactions with the door and its protruding insulators. As the retention door retracts, particles are allowed to loft into an open volume, achieving motion due to electrostatic repulsion. The electrometer system measures the charge transfer between the granular material and the insulators. As the charged grains exit the bed, they travel through an applied electric field and a camera observes the kinematics of the individual grains whose trajectories are determined by their net charges. The design of the ERIE electrometer instrument and initial results from the first flight was presented at the 2021 AGU Fall Meeting under P55E-2002. Shortly after microgravity was achieved and the retaining door began to open, the rate of charge acquisition measured by the electrometer increased, indicating the insulators were accumulating triboelectric charge. Charged grains were observed in the video data to traverse across the external electric field and become deflected from a linear path due to their charges. Pairs of grains were also observed to orbit one another as expected from two oppositely charged bodies in proximity to one another. Improvements to the design of the instrument and preliminary results obtained from the second flight scheduled for Q3 2022 will be presented at this meeting.

Electrostatics↗

Mixed Reality Training and Workspace Integration

Mixed reality technology is being used across Idaho National Laboratory (INL) to enhance training and workforce development. Projects involving mixed reality such as lockout/tagout , the Industrial Control System Laboratory , and a Department of Defense microreactor demonstration have benefited from these innovative approaches. Several key concerns exist with integrating this new technology, including ease of use, ease of setup, and maintenance through the lifecycle. These aspects need to be properly addressed to ensure that this technology remains attractive and useful to operations teams as well as engineers and researchers at INL. Primarily, this requires buy-in from information technology management, designing software/hardware-agnostic tools, and reducing friction with technology integration. To be successful, regular operational use of this new and unfamiliar technology will require straightforward user interfaces, simple setup processes, and feature-rich experiences that reduce the time needed to benefit from the technology. INL is improving its toolset to allow for a streamlined deployment and use of mixed reality technologies that are directly available to researchers and engineers.

99 GENERAL AND MISCELLANEOUS↗

Correlated two-particle diffusion in dense colloidal suspensions at early times: Theory and comparison to experiment

The spatially resolved diffusive dynamic cross correlations of a pair of colloids in dense quasi-two-dimensional monolayers of identical particles are studied experimentally and theoretically at early times where motion is Fickian. In very dense systems where strong oscillatory equilibrium packing correlations are present, we find an exponential decay of the dynamic cross correlations on small and intermediate length scales. At large separations where structure becomes random, an apparent power law decay with an exponent of approximately –2.2 is observed. For a moderately dense suspension where local structural correlations are essentially absent, this same apparent power law decay is observed over all probed interparticle separations. A microscopic nonhydrodynamic theory is constructed for the dynamic cross correlations which is based on interparticle frictional effects and effective structural forces. Hydrodynamics enters only via setting the very short-time single-particle self-diffusion constant. No-adjustable-parameter quantitative predictions of the theory for the dynamic cross correlations are in good agreement with experiment over all length scales. The origin of the long-range apparent power law is the influence of the constraint of fixed interparticle separation on the amplitude of the mean square force exerted on the two tagged particles by the surrounding fluid. The theory is extended to study high-packing-fraction 3D hard sphere fluids. Here, the same pattern of an oscillatory exponential form of the dynamic cross correlation function is predicted in the structural regime, but the long-range tail decays faster than in monolayers with an exponent of –3.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Mechanism of lubrication by tricresylphosphate (TCP)

The coefficient of friction was measured as a function of temperature on a pin-on-disk tribometer. Pins and disks of 440C and 52100 steels were lubricated with tricresylphosphate (TCP), 3.45 percent TCP in squalene, and pure squalene. The M-50 pins and disks were lubricated with 3.45 percent TCP in squalene and pure squalene. Experiments were conducted under limited lubrication conditions in dry ( 100 ppm H2O) air and dry ( pp H2O) nitrogen at 50 rpm (equivalent to a sliding velocity of 13 cm sec) and a constant load of 9.8 N (1 kg). Characteristic temperatures T sub r were identified for TCP on 52100 steel and for squalene on M-50 and 52100 steels, where the friction decreased because of a chemical reaction between the lubricant and the metal surface. The behavior of squalene obscured the influence of 3.45 percent TCP solute on the friction of the system. Wear volume measurements demonstrated that wear was lowest at temperatures just above T sub r. Comparing the behavior of TCP on M-50, 440C, and 52100 steels revealed that the TCP either reacted to give T sub r behavior or produced initial failure in the temperature range 223 + or - 5 C.

Faut, O. D.↗

Is Diffusion Anomalous in Two-Dimensional Yukawa Liquids?

There have recently been many predictions of 'superdiffusion' in two-dimensional strongly coupled Yukawa systems, both by computer simulations and in dusty plasma experiments, with substantially varying diffusion exponents. Here we show that the results crucially depend on the strength of dissipation and the time instant of the measurement. For sufficiently large friction even subdiffusion is possible. However, there are strong indications that, in the long-time limit, anomalous diffusion vanishes and the system returns to normal diffusion, for dissipative as well as for frictionless systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cladding Profilometry Analysis of Experimental Breeder Reactor-II Metallic Fuel Pins with HT9, D9, and SS316 Cladding

BISON finite element method fuel performance simulations were conducted using an existing automated process that couples the Fuels Irradiation & Physics Database (FIPD) and the Integral Fast Reactor Materials Information System database by writing input files and comparing the BISON output to post-irradiation fuel pin profilometry measurements contained within the databases. The importance of this work is to demonstrate the ability to benchmark fuel performance metallic fuel models within BISON using Experimental Breeder Reactor-II fuel pin data for a number of similar pins, while building off previous modeling efforts. Changes to the generic BISON input file include implementing pin specific axial power and flux profiles, pin specific fluences, frictional contact, and irradiation-induced volumetric swelling models for cladding. A statistical analysis of irradiation-induced volumetric swelling models for HT9, D9, and SS316 was performed for experiments X421/X421A, X441/X441A, and X486. Between these three experiments, there were 174 post-irradiation examination (PIE) profilometries used for validating the swelling models presented using a standard error of the estimate (SEE) method. Implementation of the volumetric swelling models for D9 and SS316 claddings was found to have a significant impact on the BISON profilometry simulated, where HT9 clad pins had an insignificant change due to low fluence values. BISON profilometry simulated for HT9, D9, and SS316 fuel pins agreed with PIE profilometry measurements, with assembly SEE values being 4.4 × 10−3 for X421A, 2.0 × 10−3 for X441A, and 2.8 × 10−3 for X486. D9 clad pins in X421/X421A had the highest SEE values, which is due to the BISON simulated profilometry being shifted axially. While this work accomplished its purpose to demonstrate the modeling of multiple fuel pins from the databases to help validate models, the results suggest that the continued development of metallic fuel models is necessary for qualifying new metallic fuel systems to better capture some physical performance phenomena, such as the hot pressing of U-Pu-Zr and the fuel cladding chemical interaction.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Re-examination of compliant wall experiments in air with water substrates

A possible alternative explanation is proposed for compliant wall drag reductions measured in previous investigations. Standing waves were observed to form on the surfaces of compliant wall models in air with water substrates as the freestream velocity was increased from 15 to 30 m/s. These waves resembled sine waves with half of the wave protruding over the upstream portion of the model and the other half being recessed over the downstream end of the model. These data coupled with results of recent drag reduction experiments suggest that standing waves could have caused a shift in the model center of gravity creating a bending moment that was interpreted as a reduction in the skin friction drag.

Hefner, J. N.↗