Search NASA⌕ Search

SEARCH · Search NASA

Results for “hardware testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Liquid Oxygen/Liquid Methane Propulsion and Cryogenic Advanced Development

Exploration Systems Architecture Study conducted by NASA in 2005 identified the liquid oxygen (LOx)/liquid methane (LCH4) propellant combination as a prime candidate for the Crew Exploration Vehicle Service Module propulsion and for later use for ascent stage propulsion of the lunar lander. Both the Crew Exploration Vehicle and Lunar Lander were part the Constellation architecture, which had the objective to provide global sustained lunar human exploration capability. From late 2005 through the end of 2010, NASA and industry matured advanced development designs for many components that could be employed in relatively high thrust, high delta velocity, pressure fed propulsion systems for these two applications. The major investments were in main engines, reaction control engines, and the devices needed for cryogenic fluid management such as screens, propellant management devices, thermodynamic vents, and mass gauges. Engine and thruster developments also included advanced high reliability low mass igniters. Extensive tests were successfully conducted for all of these elements. For the thrusters and engines, testing included sea level and altitude conditions. This advanced development provides a mature technology base for future liquid oxygen/liquid methane pressure fed space propulsion systems. This paper documents the design and test efforts along with resulting hardware and test results.

Klem, Mark D.↗

Long Term Displacement Data of Woven Fabric Webbings Under Constant Load for Inflatable Structures

Inflatable modules for space applications offer weight and launch volume savings relative to current metallic modules. Limited data exist on the creep behavior of the restraint layer of inflatable modules. Long-term displacement and strain data of two high strength woven fabric webbings, Kevlar and Vectran, under constant load is presented. The creep behavior of webbings is required by designers to help determine service life parameters of inflatable modules. Four groups of different webbings with different loads were defined for this study. Group 1 consisted of 4K Kevlar webbings loaded to 33% ultimate tensile strength and 6K Vectran webbings loaded to 27% ultimate tensile strength, group 2 consisted of 6K Kevlar webbings loaded to 40% and 43% ultimate tensile strength, and 6K Vectran webbings loaded to 50% ultimate tensile strength, group 3 consisted of 6K Kevlar webbings loaded to 52% ultimate tensile strength and 6K Vectran webbings loaded to 60% ultimate tensile strength, and group 4 consisted of 12.5K Kevlar webbings loaded to 22% ultimate tensile strength, and 12.5K Vectran webbings loaded to 22% ultimate tensile strength. The uniquely designed test facility, hardware, displacement measuring devices, and test data are presented. Test data indicate that immediately after loading all webbings stretch an inch or more, however as time increases displacement values significantly decrease to fall within a range of several hundredth of an inch over the remainder of test period. Webbings in group 1 exhibit near constant displacements and strains over a 17-month period. Data acquisition was suspended after the 17th month, however webbings continue to sustain load without any local webbing damage as of the 21st month of testing. Webbings in group 2 exhibit a combination of initial constant displacement and subsequent increases in displacement rates over a 16-month period. Webbings in group 3 exhibit steady increases in displacement rates leading to webbing failure over a 3-month period. Five of six webbings experienced local damage and subsequent failure in group 3. Data from group 4 indicates increasing webbing displacements over a 7-month period. All webbings in groups 1, 2, and 4 remain suspended without any local damage as of the writing of this paper. Variations in facility temperatures over test period seem to have had limited effect on long-term webbing displacement data.

Kenner, Winfred S.↗

High Density Vertiplex: Scalable Autonomous Operations Flight Test

The NASA High Density Vertiport project has completed a multi-aircraft flight test of a scalable autonomous vertiport prototype system. These tests included end to end system integration testing of hardware and software, operational procedure testing of defined roles and responsibilities within a vertiport environment, and human factors data collection. This paper provides an overview of the flight test setup , scenarios, and summary results.

AAM↗

Automatic Parameter Tuning for the Morpheus Vehicle Using Particle Swarm Optimization

A high fidelity simulation using a PC based Trick framework has been developed for Johnson Space Center's Morpheus test bed flight vehicle. There is an iterative development loop of refining and testing the hardware, refining the software, comparing the software simulation to hardware performance and adjusting either or both the hardware and the simulation to extract the best performance from the hardware as well as the most realistic representation of the hardware from the software. A Particle Swarm Optimization (PSO) based technique has been developed that increases speed and accuracy of the iterative development cycle. Parameters in software can be automatically tuned to make the simulation match real world subsystem data from test flights. Special considerations for scale, linearity, discontinuities, can be all but ignored with this technique, allowing fast turnaround both for simulation tune up to match hardware changes as well as during the test and validation phase to help identify hardware issues. Software models with insufficient control authority to match hardware test data can be immediately identified and using this technique requires very little to no specialized knowledge of optimization, freeing model developers to concentrate on spacecraft engineering. Integration of the PSO into the Morpheus development cycle will be discussed as well as a case study highlighting the tool's effectiveness.

Birge, B.↗

SUbsonic Single Aft eNgine (SUSAN) Power/Propulsion System Hardware-in-the-Loop Test Results

Electrified Aircraft Propulsion (EAP) technology offers a promising path forward for reducing greenhouse gas emissions and other negative environmental effects from the commercial aviation sector. EAP systems can reduce fuel burn and improve performance over state-of the-art designs, however the increased complexity and highly coupled nature of these systems present challenges that require new control approaches. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a concept aircraft developed by NASA as a reference design for a commercial transport aircraft with a highly integrated hybrid-electric powertrain. This paper summarizes the results of a Hardware-in-the-Loop (HIL) test of a control architecture developed for the SUSAN power/propulsion system (PPS). The test was performed in the Hybrid Propulsion Emulation Rig (HyPER) facility at the NASA Glenn Research Center (GRC) and involved a real-time reference model of the SUSAN PPS and control system running with a sub-scale electro-mechanical system replacing one of the PPS subsystems. A side-by-side comparison of the simulated and real systems in the HIL test results shows that the control architecture functions well in both the simulation and the real-time HIL environment. In both cases the controller is able to simultaneously deliver the required thrust response and balance power levels between the electrical and turbomachinery subsystems.

Jonah J Sachs-Wetstone↗

SUbsonic Single Aft eNgine (SUSAN) Power/Propulsion System Hardware-in-the-Loop Test Results

Electrified Aircraft Propulsion (EAP) technology offers a promising path forward for reducing greenhouse gas emissions and other negative environmental effects from the commercial aviation sector. EAP systems can reduce fuel burn and improve performance over state-of the-art designs, however the increased complexity and highly coupled nature of these systems present challenges that require new control approaches. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a concept aircraft developed by NASA as a reference design for a commercial transport aircraft with a highly integrated hybrid-electric powertrain. This paper summarizes the results of a Hardware-in-the-Loop (HIL) test of a control architecture developed for the SUSAN power/propulsion system (PPS). The test was performed in the Hybrid Propulsion Emulation Rig (HyPER) facility at the NASA Glenn Research Center (GRC) and involved a real-time reference model of the SUSAN PPS and control system running with a sub-scale electro-mechanical system replacing one of the PPS subsystems. A side-by-side comparison of the simulated and real systems in the HIL test results shows that the control architecture functions well in both the simulation and the real-time HIL environment. In both cases the controller is able to simultaneously deliver the required thrust response and balance power levels between the electrical and turbomachinery subsystems.

EAP↗

Security-Enhanced Autonomous Network Management

Ensuring reliable communication in next-generation space networks requires a novel network management system to support greater levels of autonomy and greater awareness of the environment and assets. Intelligent Automation, Inc., has developed a security-enhanced autonomous network management (SEANM) approach for space networks through cross-layer negotiation and network monitoring, analysis, and adaptation. The underlying technology is bundle-based delay/disruption-tolerant networking (DTN). The SEANM scheme allows a system to adaptively reconfigure its network elements based on awareness of network conditions, policies, and mission requirements. Although SEANM is generically applicable to any radio network, for validation purposes it has been prototyped and evaluated on two specific networks: a commercial off-the-shelf hardware test-bed using Institute of Electrical Engineers (IEEE) 802.11 Wi-Fi devices and a military hardware test-bed using AN/PRC-154 Rifleman Radio platforms. Testing has demonstrated that SEANM provides autonomous network management resulting in reliable communications in delay/disruptive-prone environments.

Zeng, Hui↗

History and Benefits of Engine Level Testing Throughout the Space Shuttle Main Engine Program

Rocket engine testing is important throughout a program s life and is essential to the overall success of the program. Space Shuttle Main Engine (SSME) testing can be divided into three phases: development, certification, and operational. Development tests are conducted on the basic design and are used to develop safe start and shutdown transients and to demonstrate mainstage operation. This phase helps form the foundation of the program, demands navigation of a very steep learning curve, and yields results that shape the final engine design. Certification testing involves multiple engine samples and more aggressive test profiles that explore the boundaries of the engine to vehicle interface requirements. The hardware being tested may have evolved slightly from that in the development phase. Operational testing is conducted with mature hardware and includes acceptance testing of flight assets, resolving anomalies that occur in flight, continuing to expand the performance envelope, and implementing design upgrades. This paper will examine these phases of testing and their importance to the SSME program. Examples of tests conducted in each phase will also be presented.

VanHooser, Katherine↗

Vapor Compression Distillation Subsystem (VCDS) component enhancement, testing and expert fault diagnostics development, volume 1

Vapor compression distillation technology for phase change recovery of potable water from wastewater has evolved as a technically mature approach for use aboard the Space Station. A program to parametrically test an advanced preprototype Vapor Compression Distillation Subsystem (VCDS) was completed during 1985 and 1986. In parallel with parametric testing, a hardware improvement program was initiated to test the feasibility of incorporating several key improvements into the advanced preprototype VCDS following initial parametric tests. Specific areas of improvement included long-life, self-lubricated bearings, a lightweight, highly-efficient compressor, and a long-life magnetic drive. With the exception of the self-lubricated bearings, these improvements are incorporated. The advanced preprototype VCDS was designed to reclaim 95 percent of the available wastewater at a nominal water recovery rate of 1.36 kg/h achieved at a solids concentration of 2.3 percent and 308 K condenser temperature. While this performance was maintained for the initial testing, a 300 percent improvement in water production rate with a corresponding lower specific energy was achieved following incorporation of the improvements. Testing involved the characterization of key VCDS performance factors as a function of recycle loop solids concentration, distillation unit temperature and fluids pump speed. The objective of this effort was to expand the VCDS data base to enable defining optimum performance characteristics for flight hardware development.

Kovach, L. S.↗

Similarity constraints in testing of cooled engine parts

A study is made of the effect of testing cooled parts of current and advanced gas turbine engines at the reduced temperature and pressure conditions which maintain similarity with the engine environment. Some of the problems facing the experimentalist in evaluating heat transfer and aerodynamic performance when hardware is tested at conditions other than the actual engine environment are considered. Low temperature and pressure test environments can simulate the performance of actual size prototype engine hardware within the tolerance of experimental accuracy if appropriate similarity conditions are satisfied. Failure to adhere to these similarity constraints because of test facility limitations or other reasons, can result in a number of serious errors in projecting the performance of test hardware to engine conditions.

Colladay, R. S.↗

Face Gear Technology for Aerospace Power Transmission Progresses

The use of face gears in an advanced rotorcraft transmission design was first proposed by the McDonnell Douglas Helicopter Company during their contracted effort with the U.S. Army under the Advanced Rotorcraft Transmission (ART) program. Face gears would be used to turn the corner between the horizontal gas turbine engine and the vertical output rotor shaft--a function currently done by spiral bevel gears. This novel gearing arrangement would substantially lower the drive system weight partly because a face gear mesh would be used to split the input power between two output gears. However, the use of face gears and their ability to operate successfully at the speeds and loads required for an aerospace environment was unknown. Therefore a proof-of-concept phase with an existing test stand at the NASA Lewis Research Center was pursued. Hardware was designed that could be tested in Lewis' Spiral Bevel Gear Test Rig. The initial testing indicated that the face gear mesh was a feasible design that could be used at high speeds and load. Surface pitting fatigue was the typical failure mode, and that could lead to tooth fracture. An interim project was conducted to see if slight modifications to the gear tooth geometry or an alternative heat treating process could overcome the surface fatigue problems. From the initial and interim tests, it was apparent that for the surface fatigue problems to be overcome the manufacturing process used for this component would have to be developed to the level used for spiral bevel gears. The current state of the art for face gear manufacturing required using less than optimal gear materials and manufacturing techniques because the surface of the tooth form does not receive final finishing after heat treatment as it does for spiral bevel gears. This resulted in less than desirable surface hardness and manufacturing tolerances. An Advanced Research and Projects Agency (ARPA) Technology Reinvestment Project has been funded to investigate the effects of manufacturing process improvements on the operating characteristics of face gears. The program is being conducted with McDonnell Douglas Helicopter Co., Lucas Western Inc., the University of Illinois at Chicago, and a NASA/U.S. Army team. The goal of the project is develop the grinding process, experimentally verify the improvement in face gear fatigue life, and conduct a full-scale helicopter transmission test. The theory and methodology to grind face gears has been completed, and manufacture of the test hardware is ongoing. Experimental verification on test hardware is scheduled to begin in fiscal 1996.

Source record↗

Space-Hardware Design for Long Life With High Reliability

In 1991, the Cassini Project, NASA's planetary project to place a spacecraft in orbit about Saturn, funded a study at the Jet Propulsion Laboratory (JPL) to identify rules for design and test of hardware required to function reliably in space for very long lifetimes. Twenty-nine subjects were considered comprising 130 specific rules related to long-life issues such as accelerated life testing, cycling of mechanical devices, selection and application of parts, semiconductor junction temperatures, and worst-case analysis for long life. The study was subsequently published as a JPL document. One major conclusion of the workshop was that unattended space missions extending out to 25 years or more are feasible.

design↗

Advancements in Lunar Dust Mitigation and Leveraging the Contamination Control Community

Lunar Dust Contamination: As we get closer to putting landers, rovers, payloads, and astronauts on the Moon, dust mitigation is becoming more critical than ever. To address the many challenges of dust mitigation on the surface, engineers and scientists are looking at various technologies that may have relevance for the contamination control community. This includes active, passive, architectural, and operational solutions. There have been advances in coatings for dust mitigation at NASA and through commercial partnerships (see Wiesner, Wohl, et al). There have been advancements to previous solutions as well as novel solutions to address dust mitigation on the surface and on-orbit. There have been several efforts to better understand the effectiveness of various terrestrial and dust mitigation solutions with much of this data published in recent years. In the area of dust mitigation, dust contamination or infiltration refers to the impingement or contact of planetary dust with items not normally dusty and whose operation may therefore be compromised. Recent Advancements in Dust Mitigation: Dust mitigation strategies are becoming more common for hardware heading to the Moon, with most major programs implementing lunar dust contamination requirements for human health and equipment. In the last couple of years, NASA has created more guidance to assist hardware developers with dust mitigation. This includes NASA-STD-1008 (Classifications and Requirements for Testing Systems and Hardware to be Exposed to Dust in Planetary) and NASA TP 20220018746 (Lunar Dust Mitigation Guide and Reference). Several projects are testing hardware in relevant dusty environments to understand their tolerance to lunar dust. There has been a significant increase in the amount of testing with lunar simulants, with the NASA Simulant Advisory Committee serving a resource for NASA and our partners. There are new solutions for detecting and monitoring the dust internally and externally. Learning from the contamination control community: In addition to sharing potentially relevant solutions at the workshop, the dust mitigation community is also interested in learning from the contamination control community on ways to address lunar dust. For instance, a major aspect of managing the dust is monitoring and detection. This is critical for understanding when maintenance is needed and to inform future missions. Another challenge of working with lunar dust is quantifying and characterizing the smallest of particles. There are also challenges in modeling lunar dust and its behavior. The dust mitigation community can also leverage lessons learned from the planetary protection community.

dust mitagation↗

Use of Heritage Hardware on MPCV Exploration Flight Test One

Due to an aggressive schedule for the first orbital test flight of an unmanned Orion capsule, known as Exploration Flight Test One (EFT1), combined with severe programmatic funding constraints, an effort was made to identify heritage hardware, i.e., already existing, flight-certified components from previous manned space programs, which might be available for use on EFT1. With the end of the Space Shuttle Program, no current means exists to launch Multi Purpose Logistics Modules (MPLMs) to the International Space Station (ISS), and so the inventory of many flight-certified Shuttle and MPLM components are available for other purposes. Two of these items are the Shuttle Ground Support Equipment Heat Exchanger (GSE Hx) and the MPLM cabin Positive Pressure Relief Assembly (PPRA). In preparation for the utilization of these components by the Orion Program, analyses and testing of the hardware were performed. The PPRA had to be analyzed to determine its susceptibility to pyrotechnic shock, and vibration testing had to be performed, since those environments are predicted to be significantly more severe during an Orion mission than those the hardware was originally designed to accommodate. The GSE Hx had to be tested for performance with the Orion thermal working fluids, which are different from those used by the Space Shuttle. This paper summarizes the certification of the use of heritage hardware for EFT1.

Rains, George Edward↗

Application of a microprocessor to a spacecraft attitude control

The attitude control system (ACS) microprocessor development work spanned three main design areas: hardware and instruction set, ACS firmware, and hardware firmware verification testing. The processor hardware utilizes two parallel 4 bit microprocessors. The firmware includes data processing for five sensors, four attitude control laws, and telemetry and commands.

Brady, D. H.↗

Tethered Satellite System Contingency Investigation Board

The Tethered Satellite System (TSS-1) was launched aboard the Space Shuttle Atlantis (STS-46) on July 31, 1992. During the attempted on-orbit operations, the Tethered Satellite System failed to deploy successfully beyond 256 meters. The satellite was retrieved successfully and was returned on August 6, 1992. The National Aeronautics and Space Administration (NASA) Associate Administrator for Space Flight formed the Tethered Satellite System (TSS-1) Contingency Investigation Board on August 12, 1992. The TSS-1 Contingency Investigation Board was asked to review the anomalies which occurred, to determine the probable cause, and to recommend corrective measures to prevent recurrence. The board was supported by the TSS Systems Working group as identified in MSFC-TSS-11-90, 'Tethered Satellite System (TSS) Contingency Plan'. The board identified five anomalies for investigation: initial failure to retract the U2 umbilical; initial failure to flyaway; unplanned tether deployment stop at 179 meters; unplanned tether deployment stop at 256 meters; and failure to move tether in either direction at 224 meters. Initial observations of the returned flight hardware revealed evidence of mechanical interference by a bolt with the level wind mechanism travel as well as a helical shaped wrap of tether which indicated that the tether had been unwound from the reel beyond the travel by the level wind mechanism. Examination of the detailed mission events from flight data and mission logs related to the initial failure to flyaway and the failure to move in either direction at 224 meters, together with known preflight concerns regarding slack tether, focused the assessment of these anomalies on the upper tether control mechanism. After the second meeting, the board requested the working group to complete and validate a detailed integrated mission sequence to focus the fault tree analysis on a stuck U2 umbilical, level wind mechanical interference, and slack tether in upper tether control mechanism and to prepare a detailed plan for hardware inspection, test, and analysis including any appropriate hardware disassembly.

Source record↗

A Method for Implementing Force-Limited Vibration Control

NASA/GSFC has implemented force-limited vibration control on a controller which can only accept one profile. The method uses a personal computer based digital signal processing board to convert force and/or moment signals into what appears to he an acceleration signal to the controller. This technique allows test centers with older controllers to use the latest force-limited control techniques for random vibration testing. The paper describes the method, hardware, and test procedures used. An example from a test performed at NASA/GSFC is used as a guide.

Worth, Daniel B.↗