SEARCH · Search NASA

Results for “open loop”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

All sources NASA NTRS DOE OSTI

NASA NTRS1993

The middeck 0-gravity dynamics experiment

The Middeck 0-Gravity Dynamics Experiment (MODE), flown onboard the Shuttle STS-48 Mission, consists of three major elements: the Experiment Support Module, a dynamics test bed providing computer experiment control, analog signal conditioning, power conditioning, an operator interface consisting of a keypad and display, experiment electrical and thermal control, and archival data storage: the Fluid Test Article assembly, used to investigate the dynamics of fluid-structure interaction in 0-gravity; and the Structural Test Article for investigating the open-loop dynamics of structures in 0-gravity. Deployable, erectable, and rotary modules were assembled to form three one- and two-dimensional structures, in which variations in bracing wire and rotary joint preload could be introduced. Change in linear modal parameters as well as the change in nonlinear nature of the response is examined. Trends in modal parameters are presented as a function of force amplitude, joint preload, and ambient gravity. An experimental study of the lateral slosh behavior of contained fluids is also presented. A comparison of the measured earth and space results identifies and highlights the effects of gravity on the linear and nonlinear slosh behavior of these fluids.

Crawley, Edward F.↗

NASA NTRS1992

A structurally adaptive space crane concept for assembling space systems on orbit

A space crane concept is presented which is based on erectable truss hardware to achieve high stiffness and low mass booms and articulating-truss joints which can be assembled on orbit. The hardware is characterized by linear load-deflection response and is structurally predictable. The crane can be reconfigured into different geometries to meet future assembly requirements. Articulating-truss joint concepts with significantly different geometries are analyzed and found to have similar static and dynamic performance, which indicates that criteria other than structural and kinematic performance can be used to select a joint. Passive damping and an open-loop preshaped command input technique greatly enhance the structural damping in the space crane and may preclude the need for an active vibrations suppression system.

Dorsey, John T.↗

NASA NTRS1992

Sub-domain decomposition methods and computational controls for multibody dynamical systems

This paper presents a concurrent methodology to simulate the dynamics of flexible multibody systems with a large number of degrees of freedom. A general class of open-loop structures is treated and a redundant coordinate formulation is adopted. A range space method is used in which the constraint forces are calculated using a preconditioned conjugate gradient method. By using a preconditioner motivated by the regular ordering of the directed graph of the structures, it is shown that the method is order N in the total number of coordinates of the system. The overall formulation has the advantage that it permits fine parallelization and does not rely on system topology to induce concurrency. It can be efficiently implemented on the present generation of parallel computers with a large number of processors. Validation of the method is presented via numerical simulations of space structures incorporating large number of flexible degrees of freedom.

Menon, R. G.↗

NASA NTRS1992

Real Km-synthesis via generalized Popov multipliers

The authors refine their H-infinity control designs presented at the 1990 and 1991 American Control Conference by introducing a new real Km-synthesis technique involving the use of generalized Popov multipliers. This multiplier technique substantially reduces, and in some cases may even eliminate altogether, the conservativeness associated with traditional Km-synthesis solutions in which all uncertainties are treated as complex, even when they arise from real parameters such as the masses and spring constants in the benchmark problem. The design results demonstrate how this approach permits a very precise analysis of the intrinsic tradeoffs between robustness, performance, and control energy requirements. Also included is an open-loop H-infinity prefilter design that makes it possible to address the command response shaping issue. The design concept has been applied to the benchmark problem no. 4 and successfully removes the initial undesired transient and cuts down the percent overshoot.

Chiang, R. Y.↗

NASA NTRS1992

Achieving safe autonomous landings on Mars using vision-based approaches

Autonomous landing capabilities will be critical to the success of planetary exploration missions, and in particular to the exploration of Mars. Past studies have indicated that the probability of failure associated with open-loop landings is unacceptably high. Two approaches to achieving autonomous landings with higher probabilities of success are currently under analysis. If a landing site has been certified as hazard free, then navigational aids can be used to facilitate a precision landing. When only limited surface knowledge is available and landing areas cannot be certified as hazard free, then a hazard detection and avoidance approach can be used, in which the vehicle selects hazard free landing sites in real-time during its descent. Issues pertinent to both approaches, including sensors and algorithms, are presented. Preliminary results indicate that one promising approach to achieving high accuracy precision landing is to correlate optical images of the terrain acquired during the terminal descent phase with a reference image. For hazard detection scenarios, a sensor suite comprised of a passive intensity sensor and a laser ranging sensor appears promising as a means of achieving robust landings.

Pien, Homer↗

NASA NTRS1992

Vibration control of a manipulator tip on a flexible body

Vibration control of a rigid manipulator tip on a main flexible uniform beam is examined. It is proposed to add a compensator between the manipulator and the beam to rotate and extend/retrieve the manipulator during the control period. The 2D station-keeping maneuvers within the linear range without gravity and damping are considered. The compensatory open-loop control law, which depends on the amplitudes of the beam's flexible deformations at the connection joint, is synthesized using linear quadratic regulator techniques. After introducing the compensatory control into the system, system control is still stable, and the tip coordinates of the manipulator can be made to closely follow the rigid beam motion, which is assumed to be a desired motion.

Xu, J.↗

NASA NTRS1993

Sensitivity analysis of Lyapunov and Riccati equations with application to controls-structures integrated design

Controls-structure integrated design is a complicated multidisciplinary design optimization problem which involves the state equations pertaining to open-loop eigenvalues and control laws. In order to alleviate the intensity of the computation, this study uses the adjoint variable method to derive sensitivity equations for the eigenvalue, Liapunov, and Riccati equations. These individual sensitivity equations are then combined together to form the multidisciplinary sensitivity equations for the control structure integrated design problems. A set of linear sensitivity equations, proportional in number to the number of performance functions involved in the optimization process, are solved. This proposed approach may provide a great saving in computer resources. The validity of the newly developed sensitivity equations is verified by numerical examples.

Hou, Gene↗

NASA NTRS1991

Sequential design of linear quadratic state regulators with prescribed eigenvalues and specified relative stability

This paper considers the problem of optimal regulator design of linear multivariable systems with prescribed pole locations and/or poles corresponding to specified relative stability. A sequential method based on the frequency-domain optimality condition is proposed for achieving the desired pole assignment and determination of the corresponding quadratic performance index. This design method enables the retention of some stable open-loop poles and the associated eigenvectors in the closed-loop system. An illustrative example is provided to demonstrate the effectiveness of the proposed method.

Ganesan, Sekar↗

NASA NTRS1993

Robust time-optimal control of uncertain structural dynamic systems

A time-optimal open-loop control problem of flexible spacecraft in the presence of modeling uncertainty has been investigated. The results indicate that the proposed approach significantly reduces the residual structural vibrations caused by modeling uncertainty. The results also indicate the importance of proper jet placement for practical tradeoffs among the maneuvering time, fuel consumption, and performance robustness.

Wie, Bong↗

NASA NTRS1993

On the estimation algorithm for adaptive performance optimization of turbofan engines

The performance seeking control (PSC) algorithm is designed to continuously optimize the performance of propulsion systems. The PSC algorithm uses a nominal propulsion system model and estimates, in flight, the engine deviation parameters (EDPs) characterizing the engine deviations with respect to nominal conditions. In practice, because of measurement biases and/or model uncertainties, the estimated EDPs may not reflect the engine's actual off-nominal condition. This factor has a direct impact on the PSC scheme exacerbated by the open-loop character of the algorithm. In this paper, the effects produced by unknown measurement biases over the estimation algorithm are evaluated. This evaluation allows for identification of the most critical measurements for application of the PSC algorithm to an F100 engine. An equivalence relation between the biases and EDPs stems from the analysis; therefore, it is undecided whether the estimated EDPs represent the actual engine deviation or whether they simply reflect the measurement biases. A new algorithm, based on the engine's (steady-state) optimization model, is proposed and tested with flight data. When compared with previous Kalman filter schemes, based on local engine dynamic models, the new algorithm is easier to design and tune and it reduces the computational burden of the onboard computer.

Espana, Martin D.↗

NASA NTRS1993

Near minimum-time maneuvers of large space structures using parameter optimization

Near minimum-time attitude maneuvers for large, inherently-flexible space structures with finite fuel supplies are investigated. The open loop maneuver is determined with the Sequential Quadratic Programming (SQP) algorithm, which optimizes a bang-off-bang control parameter set for the given maneuver. Torque smoothing is used to prevent discontinuities in the control which would excite the flexible structure. Additional system dynamics such as thruster inefficiency, spring forces and pressure leaks are identified from preliminary experiments on the ASTREX test article.

Carter, M. T.↗

NASA NTRS1993

Robust fuel- and time-optimal control of uncertain flexible space structures

The problem of computing open-loop, fuel- and time-optimal control inputs for flexible space structures in the face of modeling uncertainty is investigated. Robustified, fuel- and time-optimal pulse sequences are obtained by solving a constrained optimization problem subject to robustness constraints. It is shown that 'bang-off-bang' pulse sequences with a finite number of switchings provide a practical tradeoff among the maneuvering time, fuel consumption, and performance robustness of uncertain flexible space structures.

Wie, Bong↗

NASA NTRS1993

Simulation motion effect on single axis compensatory tracking

An experiment that examined how changes in a motion platform drive filter affect pilot-vehicle performance and opinion was conducted on the NASA Ames Vertical Motion Simulator. Pilots controlled a simplified helicopter model in the vertical or the directional axis and tracked a randomly moving target aircraft in the presence of a random disturbance. With both tasks, variations from full motion to fixed-base conditions were made in the high-pass drive filter gain and natural frequency. The results indicate that vertical motion did not affect the open-loop pilot-vehicle target-tracking crossover frequency, but target-tracking phase margins improved with increased filter gain or decreased natural frequency. Vertical disturbance-rejection crossover frequency increased with decreasing filter natural frequency, while disturbance rejection phase margins improved with increasing filter gain. Vertical tracking errors increased significantly when all vertical motion was removed. No significant differences were measured among the directional configurations, which indicates that pure yaw motion cues may not be as important as previously thought in flight simulation.

Schroeder, Jeffery A.↗

NASA NTRS1992

Low power, highly linear output buffer

A class AB CMOS output buffer has been designed for use on an IR focal plane array. Given the requirements for power dissipation and load capacitance a class A output, such as a source follower, would be unsuitable. The approach taken uses a class AB amplifier configured as a charge integrator. Thus it converts a charge packet in the focal plane multiplexer to a voltage which is then the output of the focal plane. With a quiescent current of 18 micro-a and a load capacitance of 100 pf, the amplifier has an open loop unity gain bandwidth of 900 khz. Integral nonlinearity is better than .03 percent over 5.5 volts when run with VDD-VSS = 6v.

Foley, D.↗

NASA NTRS1991

A time domain inverse dynamic method for the end point tracking control of a flexible manipulator

The inverse dynamic equation of a flexible manipulator was solved in the time domain. By dividing the inverse system equation into the causal part and the anticausal part, we calculated the torque and the trajectories of all state variables for a given end point trajectory. The interpretation of this method in the frequency domain was explained in detail using the two-sided Laplace transform and the convolution integral. The open loop control of the inverse dynamic method shows an excellent result in simulation. For real applications, a practical control strategy is proposed by adding a feedback tracking control loop to the inverse dynamic feedforward control, and its good experimental performance is presented.

Kwon, Dong-Soo↗

NASA NTRS1988

An adaptive identification and control scheme for large space structures

A unified identification and control scheme capable of achieving space at form performance objectives under nominal or failure conditions is described. Preliminary results are also presented, showing that the methodology offers much promise for effective robust control of large space structures. The control method is a multivariable, adaptive, output predictive controller called Model Predictive Control (MPC). MPC uses a state space model and input reference trajectories of set or tracking points to adaptively generate optimum commands. For a fixed model, MPC processes commands with great efficiency, and is also highly robust. A key feature of MPC is its ability to control either nonminimum phase or open loop unstable systems. As an output controller, MPC does not explicitly require full state feedback, as do most multivariable (e.g., Linear Quadratic) methods. Its features are very useful in LSS operations, as they allow non-collocated actuators and sensors. The identification scheme is based on canonical variate analysis (CVA) of input and output data. The CVA technique is particularly suited for the measurement and identification of structural dynamic processes - that is, unsteady transient or dynamically interacting processes such as between aerodynamics and structural deformation - from short, noisy data. CVA is structured so that the identification can be done in real or near real time, using computationally stable algorithms. Modeling LSS dynamics in 1-g laboratories has always been a major impediment not only to understanding their behavior in orbit, but also to controlling it. In cases where the theoretical model is not confirmed, current methods provide few clues concerning additional dynamical relationships that are not included in the theoretical models. CVA needs no a priori model data, or structure; all statistically significant dynamical states are determined using natural, entropy-based methods. Heretofore, a major limitation in applying adaptive controllers to LSS problems has been the requirement for accurate models. We feel that MPC coupled with the CVA identification scheme will resolve this limitation. The results are based on research performed under an SBIR grant, administered by the Air Force Office of Scientific Research.

Carroll, J. V.↗

NASA NTRS1990

A multidisciplinary approach to optimization of controlled space structures

A fundamental problem facing controls-structures analysts is a means of determining the trade-offs between structural design parameters and control design parameters in meeting some particular performance criteria. Developing a general optimization-based design methodology integrating the disciplines of structural dynamics and controls is a logical approach. The objective of this study is to develop such a method. Classical design methodology involves three phases. The first is structural optimization, wherein structural member sizes are varied to minimize structural mass, subject to open-loop frequency constraints. The next phase integrates control and structure design with control gains as additional design variables. The final phase is analysis of the 'optimal' integrated design phase considering 'real' actuators and 'standard' member sizes. The control gains could be further optimized for fixed structure, and actuator saturation constraints could be imposed. However, such an approach does not take full advantage of opportunities to tailor the structure and control system design as one system.

Woodard, Stanley E.↗

NASA NTRS1993

Stress stiffening and approximate equations in flexible multibody dynamics

A useful model for open chains of flexible bodies undergoing large rigid body motions, but small elastic deformations, is one in which the equations of motion are linearized in the small elastic deformations and deformation rates. For slow rigid body motions, the correctly linearized, or consistent, set of equations can be compared to prematurely linearized, or inconsistent, equations and to 'oversimplified,' or ruthless, equations through the use of open loop dynamic simulations. It has been shown that the inconsistent model should never be used, while the ruthless model should be used whenever possible. The consistent and inconsistent models differ by stress stiffening terms. These are due to zeroth-order stresses effecting virtual work via nonlinear strain-displacement terms. In this paper we examine in detail the nature of these stress stiffening terms and conclude that they are significant only when the associated zeroth-order stresses approach 'buckling' stresses. Finally it is emphasized that when the stress stiffening terms are negligible the ruthlessly linearized equations should be used.

Padilla, Carlos E.↗