SEARCH · Search NASA

Results for “phase behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Investigating the failure behavior of cast Al-11Ce-0.4Mg alloys using in-situ scanning electron microscopy tensile testing

Within the last decade, research on Al-Ce-Mg alloys has reported promising results for use in cast part applications. In this paper, the failure behavior of cast Al-11Ce-0.4Mg (wt%) was investigated experimentally with focus on the effect the matrix and intermetallic phases have on the fracture propagation behavior at failure. For the first time, in-situ SEM tensile testing was used to study the failure behavior of cast Al-Ce alloys, reporting results for uniaxial, DIC, and single edge notch tensile tests. The results of the in-situ SEM tensile testing were compared with the materials characterization experiments, which included serial sectioning, EBSD, EDS, and fractography. Analysis of EBSD and EDS mapping of cast Al-11Ce-0.4Mg showed that the cast microstructure was a hypereutectic two phase Al-Ce alloy with grains encompassing large complex colonies of laminar eutectic Al 11 Ce 3 intermetallic. The uniaxial tensile results reported the effect casting defects have on the strength and ductility of the alloy, and DIC in-situ testing showed that the eutectic colonies plastically deform less than the matrix phase. In-situ SEM single edge notch tensile testing displayed how the strength of an individual phase affected the crack propagation direction in the alloy. The results of both the materials characterization and in-situ tensile testing experiments on the failure of this alloy revealed further directions for future alloy development that can improve both the strength and fracture toughness of Al-Ce-Mg alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Microstructural refinement of an Al-Ce-Mg alloy via Shear Assisted Processing and Extrusion

Al-Ce alloys have attracted recent interest because of their high thermal stability due to the low solubility of Ce in the Al matrix. The Al 11 Ce 3 eutectic phase gives excellent strain hardening behavior and moderate high-temperature strength in the as-cast state. However, its strengthening effect is limited by its coarse as-cast structure. Therefore, alternative manufacturing methods such as additive manufacturing or equal channel angular pressing have been applied to refine the Al 11 Ce 3 phase to good effect. However, these techniques are both expensive and time-consuming. Therefore, this study aims to use Shear Assisted Processing and Extrusion (ShAPE), an emerging solid phase processing technique that is more easily scalable than the previously mentioned methods. ShAPE can produce useful cross-sections of an Al-8Ce-4Mg alloy while refining the Al 11 Ce 3 phase to produce a higher strength material. It was found that a low temperature ShAPE process can improve the room temperature yield strength by ~60 % compared to a binary Al-4Mg alloy. Additionally, the high-temperature yield strength of the Al-Ce alloys increased by 20%, with a simultaneous 15% improvement in ductility compared to the binary Al-Mg alloy. Finally, these results highlight the potential for ShAPE as a processing technique for Al-Ce alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Wrought Aluminum-Cerium Alloys by Shear Assisted Processing and Extrusion

Al-Ce alloys have attracted recent interest because of their high thermal stability due to the very low solubility of Ce in the Al matrix. The Al 11 Ce 3 eutectic phase gives excellent strain hardening behavior and moderate high-temperature strength in the as-cast state. However, its strengthening effect is limited by its coarse as-cast structure. Therefore, alternative manufacturing methods such as additive manufacturing or equal channel angular pressing have been applied to refine the Al 11 Ce 3 phase to good effect. However, these techniques are both expensive and time-consuming. Therefore, this study aims to use Shear Assisted Processing and Extrusion (ShAPE), an emerging solid phase processing technique that is more easily scalable than the previously mentioned methods. ShAPE can produce useful cross-sections of an Al-8Ce-4Mg alloy while refining the Al 11 Ce 3 phase to produce a higher strength material. It was found that a low temperature ShAPE process can improve the room temperature yield strength by ~60% compared to a binary Al-4Mg alloy. Additionally, the high-temperature yield strength of the Al-Ce alloys increased by 20%, with a simultaneous 15% improvement in ductility compared to the binary Al-Mg alloy. These results highlight the potential for ShAPE as a processing technique for Al-Ce alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Defect cluster and nonequilibrium gas bubble associated growth in irradiated UMo fuels – a cluster dynamics and phase field model

Irradiation examination shows that gas bubble swelling kinetics is much faster after irradiation-induced recrystallization than that prior recrystallization in UMo fuels. It implies that gas bubbles in coarse grains and small recrystallized grains have different growth behavior. In this work, a phase-field model of gas bubble evolution integrating microstructure dependent cluster dynamics has been developed, for the first time, to study the gas bubble swelling behavior in the recrystallization zone of UMo fuels. Generation, diffusion, reaction, sink, emission and clustering of vacancies and interstitials are described by the cluster dynamics model while a phase-field model is used to describe the evolution of non-equilibrium gas bubbles including nucleation and growth. With the coupled model, the effect of defect generation rate, clustering rate, interstitial emission and sink rates on grain boundaries on the gas bubble evolution are systematically simulated. A set of model parameters (defect generation rate, clustering rate, interstitial emission and sink rates) is determined by comparing measured and simulated gas bubble swelling kinetics. The results demonstrate that interstitial clustering is one of the important physical mechanisms which results in a fast gas bubble swelling kinetics in the recrystallization zone. The developed model can also be extended to study the associated growth of defect and second phase precipitates often observed in irradiated materials.

Hu, Shenyang↗

DOE OSTI2023

MST-8 Colloquium: The Effect of Microstructure on the Spall Strength and Damage of 1045 Steel [Slides]

Three different microstructures of the same steel alloy were investigated to study the influence of microstructure on spall strength and damage. Microstructure influences spall behavior within the explored dynamic regime. Second phase morphology, interphase interface characteristics, and grain boundary character shown to influence spall behavior. Continued understanding of microstructure’s influence on spall and damage needed for targeted material design.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Model-based Co-Simulation of Heat Pump Water Heater with Phase Change Materials Thermal Energy Storage

The study analysis the behavior of a new developed heat pump water heater technology which integrates a phase change materials storage with a standard heat pump water heater to maximize the performance parameters of the Unified Energy Factor (UEF) and First Hour Rating (FHR). A model-based control development co-simulation platform is developed to include equipment models, such as heat pump, standard water tank, phase change materials storage tank, and integrate them with control model to support controls design, analysis, verification, and validation. Simulation results are compared with lab test results to validate the accuracy of developed co-simulation platform

Sun, Jian↗

DOE OSTI2024

Pressure-induced metallization and loss of surface magnetism in FeSi

Single-crystalline FeSi samples with a conducting surface state were studied under high pressure and magnetic field by means of electrical resistance measurements to explore how the bulk semiconducting state and the surface state are tuned by the application of pressure. Here, we found that the energy gap associated with the semiconducting bulk phase begins to close abruptly at a critical pressure of ~10 GPa and the bulk material becomes metallic with no obvious sign of any emergent phases or non-Fermi liquid behavior in temperature dependent electrical resistance in the neighborhood of the critical pressure above 3 K. Moreover, the metallic phase appears to remain at near-ambient pressure upon release of the pressure. Interestingly, the hysteresis in the electrical resistance vs magnetic field curve associated with the magnetically ordered conducting surface state decreases with pressure and vanishes at the critical pressure, while the slope of the electrical resistance vs magnetic field curve, which has a negative value for pressure below the critical pressure, decreases in magnitude with pressure and changes sign at the critical pressure. Thus the conducting surface state and the corresponding two-dimensional magnetic order collapse at the critical pressure where the energy gap of the bulk material starts to close abruptly, revealing the connection between the conducting surface state and the semiconducting bulk state in FeSi.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Hardenability and microstructural evolution of a precipitation strengthened Ni 50 Ti 21 Hf 25 Al 4 alloy

NiTi-based quaternary alloys are used in a variety of mechanical components, such as bearings, actuators, and dampers, owing to their good hardenability, wear resistance, and corrosion resistance. Additionally, one of the most notable characteristics of NiTi-based alloys is their shape memory effect and pseudoelastic properties. Connecting the macroscopic processing parameters employed in the design of new intermetallic alloys to the nanoscale structural characteristics dictating their behavior is crucial for improving their mechanical properties and expanding the spectrum of potential applications. Here, in this work, an arc melted Ni 50 Ti 21 Hf 25 Al 4 (at%) alloy was solution treated at 1050 °C followed by quenching and aging at 600 °C to investigate the effect of aging time on the microstructure and mechanical properties. Two types of nano-sized precipitates were observed and determined as face-centered orthorhombic H-phase (TiHf)Ni and L2 1 Heusler precipitates Ni 2 TiAl. The morphology and orientation of the H-phase were investigated using scanning and transmission electron microscopy (SEM and TEM), elucidating the coarsening kinetics and strengthening contribution of that phase to the intermetallic mechanical behavior. Following coarsening, the presence of Heusler nanoprecipitates was detected under overaged conditions through TEM imaging and nanobeam electron diffraction patterns. A peak hardness condition of 756 HV was achieved after 70 h of aging, indicating that the co-precipitation of H-phase and Heusler precipitates through a well-designed aging treatment can lead to optimal mechanical performance, thus elevating the alloy’s potential as a viable material for industrial applications.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Electrical and structural properties of binary Ga–Sb phase change memory alloys

Material properties of Ga–Sb binary alloy thin films deposited under ultra-high vacuum conditions were studied for analog phase change memory (PCM) applications. Crystallization of this alloy was shown to occur in the temperature range of 180–264 °C, with activation energy >2.5 eV depending on the composition. X-ray diffraction (XRD) studies showed phase separation upon crystallization into two phases, Ga-doped A7 antimony and cubic zinc-blende GaSb. Synchrotron in situ XRD analysis revealed that crystallization into the A7 phase is accompanied by Ga out-diffusion from the grains. X-ray absorption fine structure studies of the local structure of these alloys demonstrated a bond length decrease with a stable coordination number of 4 upon amorphous-to-crystalline phase transformation. Mushroom cell structures built with Ga–Sb alloys on ø110 nm TiN heater show a phase change material resistance switching behavior with resistance ratio >100 under electrical pulse measurements. TEM and Energy Dispersive Spectroscopy (EDS) studies of the Ga–Sb cells after ∼100 switching cycles revealed that partial SET or intermediate resistance states are attained by the variation of the grain size of the material as well as the Ga content in the A7 phase. A mechanism for a reversible composition control is proposed for analog cell performance. These results indicate that Te-free Ga–Sb binary alloys are potential candidates for analog PCM applications.

Ume, Rubab (ORCID:0000000324766900)↗

DOE OSTI2023

Post-irradiation examination of low burnup U 3 Si 5 and UN-U 3 Si 5 composite fuels

Here this work presents post-irradiation examination data on UN-U 3 Si 5 and U 3 Si 5 fuels at low burnup (i.e., <10–15 GWd/tHM) with Kanthal AF® cladding. The results suggest good irradiation performance for both the silicide and nitride-silicide composite pellets. Optical microscopy revealed that the pellet-cladding gap is still open, and limited axial cracking was observed only in UN-U 3 Si 5 pellets. Microcracking was isolated to the U 3 Si 5 phase in all cases and was observed in pre-irradiation and depleted pellets, indicating that it was not irradiation induced. The fission gas release was minimal for the calculated fission density achieved (2.6 – 3.15 × 10 20 fiss/cm 3 ). No fission gas bubbles were observed in the optical metallography. These results suggest acceptable swelling and fission gas behavior for both the single phase and composite compositions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Using methodical compositional tuning to optimize Co x Tb 1− x structural and magnetic properties

The Co-rich end of the Co–Tb binary phase diagram (Co x Tb 1−x , x = 0.66–0.82) has been investigated to understand the phases which form in the bulk and how they interact to yield magnetic behavior which has been reported to be ideal for use in spintronic devices. Here, this work shows that the phases and phase fractions present across this composition range follow those predicted by the binary phase diagram, and all compounds in this composition range are multiphase. Magnetic measurements show similar behavior in this composition range to related thin film work, and we attribute the observed behavior to the respective binary phases present in each compound. Ideal magnetic behavior of minimized magnetic saturation and maximized coercivity is observed in the range of x= 0.78 − 0.80 related to the majority phase Co 7 Tb 2 in these two compounds. High pressure magnetic measurements show magnetic saturation and coercivity at 300 K change little with respect to external pressure. The extension of the synthesis of these binaries into the bulk allows for specific binary phases to be targeted and analyzed for consideration in future devices.

Crystal structure↗

DOE OSTI2021

Spatially-resolved lithiation dynamics from operando X-ray diffraction and electrochemical modeling of lithium-ion cells

In this study, energy dispersive X-ray diffraction is used to profile the time evolution of ordered Li x C 6 phases in solid electrodes of lithium-ion cells charged at rates between 0.2 and 4.7C (where 1C corresponds to full discharge in 1 h). The methods for quantifying lithium concentration in these phases from the acquired diffraction patterns are described. Compact expressions for time-dependent concentration gradients in the solid electrodes using orthogonal polynomial expansions are presented. Experimentally, these gradients persisted in lithiated graphite electrodes even after the cells rested at open-circuit for over 9 h. A multiphase electrochemical model of graphite intercalation captured many of the observed behaviors, including the progression of phase transitions and the persistent gradients at zero current. However, the magnitude of concentration gradients in both the oxide cathode and graphite anode is underestimated by the model, even at moderate currents.

25 ENERGY STORAGE↗

DOE OSTI2026

Balancing moisture and oxygen can match the crystallization dynamics of inert halide perovskite processing

Understanding crystallization in ambient environments is essential for scaling the fabrication of halide perovskite solar cells. Antisolvent-free perovskite deposition offers improved compatibility with high-throughput processing but introduces distinct crystallization dynamics relative to the more ubiquitous use of antisolvents in lab-scale perovskite fabrication. These dynamics are driven by interactions between solutes, solvent and the deposition environment. Using in situ wide-angle X-ray scattering during spin-coating and annealing, we demonstrate how relative humidity (RH) and oxygen, can be tuned to drive polytype evolution during ambient crystallization of formamidinium lead iodide to match that of inert synthesis and achieve comparable film and device quality. In an inert (N 2 ) environment, we find that perovskite films follow a well-established 2H → 3C phase transformation with a short period of coexistence of the 4H and 6H phase during heating. During crystallization in dry air (RH 0%), the added presence of oxygen leads to the dominance of 4H intermediate for an extended duration, establishing a 2H → 4H → 3C pathway. Introducing low humidity (RH 10%) suppresses the 4H phase to a short-lived intermediate above 100 °C, facilitating a more direct transition to the desired 3C phase and almost replicating the crystallization behavior observed under inert conditions. Interestingly, films crystallized under RH 10% show a lower onset temperature for the perovskite 3C phase than under N 2 . At higher humidity (RH 40%), the strong interaction of oxygen and moisture with iodoplumbates appears to stabilize higher order polytypes (4H and 6H). Devices fabricated under RH 10% achieve higher efficiency and enhanced stability compared to those produced under inert atmosphere. These findings provide mechanistic insight into crystallization pathways in different environments and provide a framework to transfer processes from inert to ambient conditions. The results highlight the critical role of controlled humidity in tuning antisolvent-free perovskite crystallization for scalable processing.

Hossain, Maimur [Univ. of California, San Diego, C↗

DOE OSTI2022

Anomalous phase separation in a correlated electron system: Machine-learning–enabled large-scale kinetic Monte Carlo simulations

Significance Phase separation is crucial to the functionalities of many correlated electron materials with notable examples including colossal magnetoresistance in manganites and high- T c superconductivity in cuprates. However, the nonequilibrium phase-separation dynamics in such systems are poorly understood theoretically, partly because the required multiscale modeling is computationally very demanding. With the aid of machine-learning methods, we have achieved large-scale dynamical simulations in a representative correlated electron system. We observe an unusual relaxation process that is beyond the framework of classical phase-ordering theories. We also uncover a correlation-induced freezing behavior, which could be a generic feature of phase separation in correlated electron systems.

Zhang, Sheng↗

DOE OSTI2022

Chemical control of polarization in thin strained films of a multiaxial ferroelectric: Phase diagrams and polarization rotation

The emergent behaviors in thin films of a multiaxial ferroelectric (FE) due to electrochemical coupling between the rotating polarization and surface ions are explored within the framework of the 2–4 Landau-Ginzburg-Devonshire (LGD) thermodynamic potential combined with the Stephenson-Highland (SH) approach. The combined LGD-SH approach allows us to describe the electrochemical switching and rotation of a polarization vector in a multiaxial ferroelectric film covered by surface ions with a charge density defined by the oxygen pressure. In this work, we calculate phase diagrams, analyze the dependence of polarization components on the applied voltage, and discuss the peculiarities of quasistatic ferroelectric, dielectric, and piezoelectric hysteresis loops in thin strained multiaxial ferroelectric films. The nonlinear surface screening by oxygen ions makes the diagrams very different from the known diagrams of, e.g., strained BaTiO 3 films. Quite unexpectedly, we predict the appearance of ferroelectric reentrant phases. The obtained results point to the possibility to control the appearance and features of ferroelectric, dielectric, and piezoelectric hysteresis in multiaxial FE films covered with surface ions by varying their concentration via the partial oxygen pressure. The LGD-SH description of a multiaxial FE film can be further implemented within the Bayesian optimization framework, paving the way toward predictive materials optimization.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Alkali cation stabilization of defects in 2D MXenes at ambient and elevated temperatures

Transition metal carbides have been adopted in energy storage, conversion, and extreme environment applications. Advancements in their 2D counterparts, known as MXenes, enable the design of unique structures at the ~1 nm thickness scale. Alkali cations have been essential in MXenes manufacturing processing, storage, and applications, however, exact interactions of these cations with MXenes are not fully understood. In this study, using Ti 3 C 2 T x , Mo 2 TiC 2 T x , and Mo 2 Ti 2 C 3 T x MXenes, we present how transition metal vacancy sites are occupied by alkali cations, and their effect on MXene structure stabilization to control MXene’s phase transition. We examine this behavior using in situ high-temperature x-ray diffraction and scanning transmission electron microscopy, ex situ techniques such as atomic-layer resolution secondary ion mass spectrometry, and density functional theory simulations. In MXenes, this represents an advance in fundamentals of cation interactions on their 2D basal planes for MXenes stabilization and applications. Broadly, this study demonstrates a potential new tool for ideal phase-property relationships of ceramics at the atomic scale.

42 ENGINEERING↗

DOE OSTI2023

Mechanical properties of an Al 10 Nb 20 Ta 15 Ti 30 V 5 Zr 20 A2/B2 refractory superalloy and its constituent phases

Refractory superalloys (RSAs) are a new class of high-temperature structural materials consisting of a nanometer-sized mixture of two coherent A2 (disordered BCC) and B2 (ordered) phases. While these RSAs typically exhibit superior mechanical properties at elevated temperatures, they suffer from limited plasticity at lower temperatures, often attributed to the continuous ordered B2 matrix in these two-phase alloys. To knowledgably control the microstructure and mechanical properties of these alloys, the properties of the constitutive phases in RSAs should be known. Currently this information is absent. Here, in the present work, the microstructure and mechanical properties (at 20–1200 °C) of a candidate Al 0.5 NbTa 0.8 Ti 1.5 V 0.2 Zr RSA and two single-phase alloys, which compositions correspond to the compositions of the A2 and B2 phases in the selected RSA, are reported. Interestingly, and quite unexpectedly, the intrinsic mechanical behavior of the constituent A2 and B2 phases, deciphered for the first time in the present study, revealed that they are softer and substantially more ductile than the parent two-phase RSA. Furthermore, the ordered B2 phase exhibits a deformation twinning mechanism leading to twinning induced plasticity (TWIP) coupled with a low APB energy and activity of 1/2<111> dislocations. These mechanisms are thought to be responsible for the high plasticity of the ordered B2 phase. The results presented here question the current assumption that the ordered B2 phase in these RSAs has limited plasticity and strongly indicate that the nature of the B2/A2 interface boundaries and coherency strengthening play an important role in controlling the mechanical properties of the two-phase RSA.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Impact of size and thermal gradient on supercooling of phase change materials for thermal energy storage

Phase change material based thermal energy storage has many current and potential applications in the heating and cooling of buildings, battery and electronics thermal management, thermal textiles, and dry cooling of power plants. However, connecting lab scale thermal data obtained with differential scanning calorimetry (DSC) to the performance of large-scale practical systems has been a major challenge primarily due to the dependence of supercooling on the size and temperature gradient of the system. Here we show how a phase change material’s supercooling behavior can be characterized experimentally using common lab scale thermal analysis techniques. We then develop a statistics based theoretical model that uses the lab-scale data on small samples to quantitatively predict the supercooling performance for a general thermal energy storage application of any size, including also allowing for the possibility of temperature gradients. Finally, we validate the modeling methodology by comparing to experimental results for solid-solid phase change in neopentyl glycol, which shows how the model successfully predicts the changes in supercooling temperature across a large range of cooling rates (2 orders of magnitude) and volumes (3 orders of magnitude). By accounting for thermal gradients, the model avoids ~2x error incurred by lumped approximations.

36 MATERIALS SCIENCE↗