Results for “sample integrity” — Page 34

DOE OSTI2020

Community-Driven Metadata Standards for Agricultural Microbiome Research

Accelerating the pace of microbiome science to enhance crop productivity and agroecosystem health will require transdisciplinary studies, comparisons among datasets, and synthetic analyses of research from diverse crop management contexts. However, despite the widespread availability of crop-associated microbiome data, variation in field sampling and laboratory processing methodologies, as well as metadata collection and reporting, significantly constrains the potential for integrative and comparative analyses. Here we discuss the need for agriculture-specific metadata standards for microbiome research, and propose a list of “required” and “desirable” metadata categories and ontologies essential to be included in a future minimum information metadata standards checklist for describing agricultural microbiome studies. We begin by briefly reviewing existing metadata standards relevant to agricultural microbiome research, and describe ongoing efforts to enhance the potential for integration of data across research studies. Our goal is not to delineate a fixed list of metadata requirements. Instead, we hope to advance the field by providing a starting point for discussion, and inspire researchers to adopt standardized procedures for collecting and reporting consistent and well-annotated metadata for agricultural microbiome research.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2026

Observation of Long-Range Collective Flow in O + O and Ne + Ne Collisions and Implications for Nuclear Structure Studies

The long-range collective flow of particles produced in oxygen-oxygen ( O + O ) and neon-neon ( Ne + Ne ) collisions is measured with the CMS detector at the CERN LHC. The data samples were collected at a center-of-mass energy per nucleon pair of 5.36 TeV, with integrated luminosities of 7 nb - 1 and 0.8 nb - 1 for O + O and Ne + Ne collisions, respectively. Two- and four-particle azimuthal correlations are measured over nearly five units of pseudorapidity. Significant elliptic ( v 2 ) and triangular ( v 3 ) flow harmonics are observed in both systems. The ratios of v n coefficients between Ne + Ne and O + O collisions suggest sensitivity to the intrinsic nuclear structure of the respective Ne and O ions. Hydrodynamic models with ab initio nuclear structure inputs qualitatively reproduce the collision-overlap dependence of both the v n values and the Ne + Ne to O + O ratios. These measurements provide new constraints when modeling the interplay of nuclear structure and collective dynamics in collisions of O 16 and Ne 20 ions, respectively.

Hayrapetyan, Aram [Yerevan Phys. Inst.]↗

DOE OSTI2023

Measurement of lepton mass squared moments in B → X c ℓ ν ¯ ℓ decays with the Belle II experiment

We present measurements of the first to fourth moments of the lepton mass squared $q$ 2 of $B$ → $X_cℓ\overline{ν}_ℓ$ decays for $ℓ = e, μ$ and with $X_c$ a hadronic system containing a charm quark. These results use a sample of electron-positron collisions at the $Υ$($4S$) resonance corresponding to 62.8 fb -1 of integrated luminosity and collected by the Belle II 2 experiment in 2019 and 2020. To identify the $X_c$ system and reconstruct $q$ 2 , one of the $B$ mesons from an $Υ$($4S$) → $B\overline{B}$ decay is fully reconstructed in a hadronic decay mode using a multivariate $B$ tagging algorithm. We report raw and central moments for $q$ 2 > 1.5 $GeV$ 2 =$c$ 4 up to $q$ 2 > 8.5 $GeV$ 2 =$c$ 4 , probing up to 77% of the accessible $B$ → $X_cℓ\overline{ν}_ℓ$ phase space. This is the first measurement of moments in the experimentally challenging range of [1.5; 2.5] $GeV$ 2 =$c$ 4 . The results can be used for a new determination of |$V_{cb}$| using inclusive $B$ → $X_cℓ\overline{ν}_ℓ$ decays.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2020

Energy Storage Sizing and Operation of an Integrated Utility-Scale PV+ESS Power Plant

Integration of an energy storage system (ESS) into a large-scale grid-connected photovoltaic (PV) power plant is highly desirable to improve performance of the system and overcome the stochastic nature of PV power generation. Algorithms to size ESS within an integrated PV and ESS ( PV+ESS) power plant, conventionally, require a large number of high-resolution samples of PV generation. These algorithms are computationally expensive. In this paper, a two-day optimization algorithm that utilizes n-step constant power output dispatch every day from the PV+ESS power plant is proposed to size the ESS. Additionally, an n-step power dispatch every day through the one-year timeframe based optimization of the size of ESS is also performed. The proposed methods are computationally cheaper and provide acceptable accuracy with respect to the conventional sizing methods. The economics identified from the proposed methods are compared with the typical day-ahead hourly dispatch-based power production from the PV+ESS power plant. This comparison has shown similar economic performance showcasing the accuracy of the proposed methods in sizing the ESS. It also shows the potential for operating PV+ESS power plant in n-step constant power generation mode.

Xia, Qian↗

DOE OSTI2023

Assessment of Bulk Oxygen Capacity and Transient Redox Behavior of Foamed Lanthanum Strontium Manganese Perovskites

Synthesis of solar thermochemical hydrogen (STCH) production redox materials with engineered structures, for example, replica foams, can enable efficient heat and mass transport and are critical for scaled-up systems. Prior work has motivated the use of lanthanum strontium manganese (LSM)-type perovskites as foamed STCH materials, but the effect of their morphology on bulk and kinetic behavior has not been reported. In this work, replica and direct foamed samples of La 0.65 Sr 0.35 MnO 3-δ (LSM35) were fabricated and compared to synthesized powders and dense monoliths, and similarly synthesized CeO 2-δ (ceria) foams, regarding their specific reaction rates and bulk oxygen capacity/H 2 yields. Changes in oxygen capacity (Δδ) and reaction rates were measured between 1200 °C and 1400 °C by using fixed ratios of steam and hydrogen during both reduction and oxidation steps, allowing for analysis under practical high conversion conditions. Results suggest bulk behavior and reaction rates of the foamed LSM materials are comparable to their powder analogues. Differences in reaction rates were observed only when replica foamed samples were subjected to rapid laser heating (emulating conditions expected in solar furnaces), which is expected but has not been demonstrated at such a small scale. Here, foamed samples were further subjected to 50 redox cycles at 1400 °C to evaluate their stability. Results show no statistically significant decrease in hydrogen production for any of the foamed samples, but the direct foamed samples became brittle with time. Together, these results demonstrate the viability of replica foamed LSM perovskites for integration in scaled-up STCH systems.

08 HYDROGEN↗

DOE OSTI2026

Unraveling design principles of protein landscapes in photosynthetic membranes in plant chloroplasts

The supramolecular organization of proteins within photosynthetic membranes is crucial for energy conversion in plants. Here, we introduce an analytical and computational pipeline that integrates high-resolution cryo–scanning electron microscopy, biochemical quantification, advanced Monte Carlo computer simulations, and statistical methods to elucidate the elusive protein landscapes of grana membranes in intact Arabidopsis leaves. Our integrated analysis challenges the prevailing view that particles on the exoplasmic fracture faces in freeze-fracture samples represent photosystem II exclusively. Instead, these particles also include cytochrome b 6 f complexes. Furthermore, our steric clash analysis demonstrates that stacked membranes contain a mixture of larger PSII supercomplexes (C 2 S 2 M 2 and C 2 S 2 ) in addition to a smaller complex (C 2 ). This suggests that in vivo PSII supercomplexes exist in an equilibrium distribution of differing sizes. Furthermore, we discovered that, although size exclusion effects govern the global protein arrangement, local packing exhibits orientational order indicative of lateral attractive protein-protein interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Improved measurement of the strong-phase difference $\delta _D^{K\pi }$ in quantum-correlated $D{\overline{D}}$ decays

The decay D → K - π + is studied in a sample of quantum-correlated D$\overline{D}$ pairs, based on a data set corresponding to an integrated luminosity of 2.93 fb -1 collected at the ψ(3770) resonance by the BESIII experiment. The asymmetry between CP-odd and CP-even eigenstate decays into K - π + is determined to be A Kπ = 0.132 ± 0.011 ± 0.007, where the first uncertainty is statistical and the second is systematic. This measurement is an update of an earlier study exploiting additional tagging modes, including several decay modes involving a $K^{0}_{L}$ meson. The branching fractions of the $K^{0}_{L}$ modes are determined as input to the analysis in a manner that is independent of any strong phase uncertainty. Using the predominantly CP-even tag D → π + π - π 0 and the ensemble of CP-odd eigenstate tags, the observable $A^{πππ^0}_{Kπ}$ is measured to be 0.130 ± 0.012 ± 0.008. The two asymmetries are sensitive to $r^{Kπ}_{D}$ cos $δ^{Kπ}_{D}$ where $r^{Kπ}_{D}$ and $δ^{Kπ}_{D}$ are the ratio of amplitudes and phase difference, respectively, between the doubly Cabibbo-suppressed and Cabibbo-favoured decays. In addition, events containing D → K - π + tagged by D → $K^{0}_{S,L}$π + π - are studied in bins of phase space of the three-body decays. This analysis has sensitivity to both $r^{Kπ}_{D}$ cos $δ^{Kπ}_{D}$ and $r^{Kπ}_{D}$, sin $δ^{Kπ}_{D}$. A fit to A Kπ , $A^{πππ^0}_{Kπ}$ and the phase-space distribution of the D → $K^{0}_{S,L}$π + π - tags yields $δ^{Kπ}_{D}$ = ($187.6^{+8.9+5.4}_{-9.7-6.4}$)°, where external constraints are applied for $r^{Kπ}_{D}$ and other relevant parameters. This is the most precise measurement of $δ^{Kπ}_{D}$ in quantum-correlated D$\overline{D}$ decays.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2024

Demonstration of neutron identification in neutrino interactions in the MicroBooNE liquid argon time projection chamber

A significant challenge in measurements of neutrino oscillations is reconstructing the incoming neutrino energies. While modern fully-active tracking calorimeters such as liquid argon time projection chambers in principle allow the measurement of all final state particles above some detection threshold, undetected neutrons remain a considerable source of missing energy with little to no data constraining their production rates and kinematics. We present the first demonstration of tagging neutrino-induced neutrons in liquid argon time projection chambers using secondary protons emitted from neutron-argon interactions in the MicroBooNE detector. We describe the method developed to identify neutrino-induced neutrons and demonstrate its performance using neutrons produced in muon-neutrino charged current interactions. The method is validated using a small subset of MicroBooNE’s total dataset. The selection yields a sample with 60% of selected tracks corresponding to neutron-induced secondary protons. At this purity, the integrated efficiency is 8.4% for neutrons that produce a detectable proton.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2020

Characterization and Analysis of the Energy-Reporting Accuracy of Connected Devices

Emerging energy-efficient building systems increasingly exhibit greater functionality, often requiring multiple operating modes (e.g. white-tunability for lighting products and data traffic for devices with networked, integrated sensors). This increased functionality makes energy consumption estimates more complex. Given that these functions consume energy, the energy performance of such building systems is dependent on what operating modes they use and how much time they spend in each mode. Devices and systems that can report their own energy consumption mitigate this energy-performance uncertainty. This study explores the energy-reporting accuracy of market-available connected electrical outlets. The study considers two residential-market products (five units each, one outlet per unit) and three commercial-market products (two units each, 18 to 24 outlets per unit) with the ability to report power drawn and/or energy consumed by devices connected to their receptacles. The products were purchased through typical market channels. Pacific Northwest National Laboratory (PNNL) conducted testing in December 2018 at its Connected Lighting Test Bed (CLTB), using a custom-developed test setup and method adapted from industry standards. The setup collected energy-consumption data reported by the outlet devices under test (DUTs) at one-minute intervals and compared that data with measurements taken by a reference meter over a range of test conditions. The residential products reported power draw but not interval or cumulative energy consumption. The commercial products reported both power draw and cumulative energy consumption. Relative reporting error (RRE) was calculated for all measurements, and analysis of the results revealed variations across devices and test conditions. The total number of measurements (50 for each residential product, 60 for each commercial product) offers an appreciable comparison of performance at the make/model level. The average RRE of the residential products derived from reported power draw was -0.02% and -1.20%. The average RRE for two of the three the commercial products derived from reported power draw was worse than those of the residential products (-2.40%, -2.72%, -0.36%). The internal integration of power over time, used to calculate cumulative energy consumption, typically occurs at current and voltage sampling rates much higher than once per minute. This suggests that the average commercial-product RRE derived from reported energy consumption should be very consistent and better than performance based on reported power draw. However, the RRE derived from reported energy consumption varied significantly across the three makes of commercial-market products and was uniformly less accurate than performance based on reported power draw. Subsequent analysis identified a number of root causes for this decrease in performance, most of which were related to reporting resolution. The goals of this study are to generate awareness of building systems capable of reporting their own energy consumption, further interest in the value of energy data for a variety of uses, draw attention to how the accuracy of reported metrics can be characterized, and quantify the performance variation found in marketavailable products. The results of this study and subsequent related work may be relevant to stakeholders in industry-specification and standards-development organizations. The methods this study employs could inform test and measurement procedures and performance classifications for connected outlets, lighting products, and other building systems capable of reporting their own energy consumption. The study concludes with stakeholder recommendations, including the following: • Energy-reporting device and system manufacturers developing products that report energy consumption should characterize the accuracy of reported metrics using a reference meter calibrated by an independent laboratory that was accredited by an ILAC MRA signatory (and whose scope of accreditation explicitly covers energy measurement), and should include this information on product data sheets. • Standards and specification development organizations should develop application-specific performance classifications that end users can understand and relate to their energy-data use needs (e.g., 2% accuracy class for utility streetlight energy billing needs, or 10% accuracy class for ESCO performance verification needs). • Current or potential owners, operators, and specifiers of energy-reporting building systems should rigorously analyze the dependency of current and planned energy-data use cases on accuracy, noting in particular the dependence (or lack thereof) on relative vs. absolute accuracy, and on trueness vs. precision (i.e., repeatability), and should communicate use-case needs to industry standards and specification organizations.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

Characterization and Analysis of the Energy-Reporting Accuracy of Connected Devices

Emerging energy-efficient building systems increasingly exhibit greater functionality, often requiring multiple operating modes (e.g. white-tunability for lighting products and data traffic for devices with networked, integrated sensors). This increased functionality makes energy consumption estimates more complex. Given that these functions consume energy, the energy performance of such building systems is dependent on what operating modes they use and how much time they spend in each mode. Devices and systems that can report their own energy consumption mitigate this energy-performance uncertainty. This study explores the energy-reporting accuracy of market-available connected electrical outlets. The study considers two residential-market products (five units each, one outlet per unit) and three commercial-market products (two units each, 18 to 24 outlets per unit) with the ability to report power drawn and/or energy consumed by devices connected to their receptacles. The products were purchased through typical market channels. Pacific Northwest National Laboratory (PNNL) conducted testing in December 2018 at its Connected Lighting Test Bed (CLTB), using a custom-developed test setup and method adapted from industry standards. The setup collected energy-consumption data reported by the outlet devices under test (DUTs) at one-minute intervals and compared that data with measurements taken by a reference meter over a range of test conditions. The residential products reported power draw but not interval or cumulative energy consumption. The commercial products reported both power draw and cumulative energy consumption. Relative reporting error (RRE) was calculated for all measurements, and analysis of the results revealed variations across devices and test conditions. The total number of measurements (50 for each residential product, 60 for each commercial product) offers an appreciable comparison of performance at the make/model level. The average RRE of the residential products derived from reported power draw was -0.02% and -1.20%. The average RRE for two of the three the commercial products derived from reported power draw was worse than those of the residential products (-2.40%, -2.72%, -0.36%). The internal integration of power over time, used to calculate cumulative energy consumption, typically occurs at current and voltage sampling rates much higher than once per minute. This suggests that the average commercial-product RRE derived from reported energy consumption should be very consistent and better than performance based on reported power draw. However, the RRE derived from reported energy consumption varied significantly across the three makes of commercial-market products and was uniformly less accurate than performance based on reported power draw. Subsequent analysis identified a number of root causes for this decrease in performance, most of which were related to reporting resolution. The goals of this study are to generate awareness of building systems capable of reporting their own energy consumption, further interest in the value of energy data for a variety of uses, draw attention to how the accuracy of reported metrics can be characterized, and quantify the performance variation found in marketavailable products. The results of this study and subsequent related work may be relevant to stakeholders in industry-specification and standards-development organizations. The methods this study employs could inform test and measurement procedures and performance classifications for connected outlets, lighting products, and other building systems capable of reporting their own energy consumption. The study concludes with stakeholder recommendations, including the following: • Energy-reporting device and system manufacturers developing products that report energy consumption should characterize the accuracy of reported metrics using a reference meter calibrated by an independent laboratory that was accredited by an ILAC MRA signatory (and whose scope of accreditation explicitly covers energy measurement), and should include this information on product data sheets. • Standards and specification development organizations should develop application-specific performance classifications that end users can understand and relate to their energy-data use needs (e.g., 2% accuracy class for utility streetlight energy billing needs, or 10% accuracy class for ESCO performance verification needs). • Current or potential owners, operators, and specifiers of energy-reporting building systems should rigorously analyze the dependency of current and planned energy-data use cases on accuracy, noting in particular the dependence (or lack thereof) on relative vs. absolute accuracy, and on trueness vs. precision (i.e., repeatability), and should communicate use-case needs to industry standards and specification organizations.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

Planning Amidst Uncertainty: Identifying Core CCS Infrastructure Robust to Storage Uncertainty

Carbon Capture and Storage (CCS) is a critical technology for reducing anthropogenic CO2 emissions, but its large-scale deployment is complicated by uncertainties in geological storage performance. These uncertainties pose significant financial and operational risks, as underperforming storage sites can lead to costly infrastructure modifications, inefficient pipeline routing, and economic shortfalls. To address this challenge, we propose a novel optimization workflow that is based on mixed-integer linear programming and explicitly integrates probabilistic modeling of storage uncertainty into CCS infrastructure design. This workflow generates multiple infrastructure scenarios by sampling storage capacity distributions, optimally solving each scenario using a mixed-integer linear programming model, and aggregating results into a heatmap to identify core infrastructure components that have a low likelihood of underperforming. A risk index parameter is introduced to balance trade-offs between cost, CO2 processing capacity, and risk of underperformance, allowing stakeholders to quantify and mitigate uncertainty in CCS planning. Applying this workflow to a CCS dataset from the US Department of Energy’s Carbon Utilization and Storage Partnership project reveals key insights into infrastructure resilience. Reducing the risk index from 15% to 0% is observed to lead to an 83.7% reduction in CO2 processing capacity and a 77.1% decrease in project profit, quantifying the trade-off between risk tolerance and project performance. Furthermore, our results highlight critical breakpoints, where small adjustments in the risk index produce disproportionate shifts in infrastructure performance, providing actionable guidance for decision-makers. Unlike prior approaches that aimed to cheaply repair underperforming infrastructure, our workflow constructs robust CCS networks from the ground up, ensuring cost-effective infrastructure under storage uncertainty. These findings demonstrate the practical relevance of incorporating uncertainty-aware optimization into CCS planning, equipping decision-makers with a tool to make informed project planning decisions.

Olson, Daniel↗

DOE OSTI2022

Different Formation Scenarios for Counterrotating Stellar Disks in Nearby Galaxies

Using the integral field unit data from the Mapping Nearby Galaxies at Apache Point Observatory survey, we select a sample of 101 galaxies with counterrotating stellar disks and regularly rotating ionized gas disks. We classify the 101 galaxies into four types based on the features of their stellar velocity fields. The relative fractions and stellar population age radial gradients of the four types are different in the blue cloud, green valley, and red sequence populations. We suggest different formation scenarios for counterrotating stellar disks; the key factors in the formation of counterrotating stellar disks include (1) the abundance of preexisting gas in the progenitor and (2) the efficiency in angular momentum consumption.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2021

Microfracture-pore structure characterization and water-rock interaction in three lithofacies of the Lower Eagle Ford Formation

The microfracture-pore structures and water-rock interactions of eight samples of three typical lithofacies (three limestone, three wackestone, and two mudstone) from the Lower Eagle Ford Formation have been investigated using an integrated methodology. The methods used were X-ray diffraction (XRD), total organic carbon (TOC) content, pyrolysis, thin-section petrography, scanning electron microscopy (SEM), mercury intrusion porosimetry (MIP), spontaneous water imbibition, and water vapor & nitrogen physisorption. Petrophysical properties such as organic richness, maturity, mineral composition, types and patterns of microfractures and pores, porosity, pore-throat size distribution, pore size distribution, pore connectivity, water adsorption and desorption behavior were determined from these methods, and the results compared among the three lithofacies. For example, the three limestone EAS samples and three wackestone DM samples show a low porosity range from 2.02–3.35%, whereas the two mudstone VRU samples exhibit a much large average porosity of 11.7% by MIP results. Nitrogen physisorption results show that pore size distributions have a good similarity in N2 adsorption volume for the samples with similar lithology. Microfractures are morphologically divided into seven types, with their definitions & pictorial examples presented and possible formation mechanisms proposed. In addition, the water vapor physisorption behavior and their controlling factors are discussed. Here, the water adsorption capacity shows a positive relationship (R 2 = 0.90) with clay content and a negative relationship (R 2 = 0.99) with carbonate content. In general, this integrated study of microfracture-pore structure characterization and water-rock interaction provides some insights of water vapor adsorption behavior in different lithofacies and whether microfractures could be an important pathway for fluid flow.

58 GEOSCIENCES↗

DOE OSTI2024

Methods for Quantitative Thermal Analysis of Lithium Solid-State and Beyond Battery Safety

The use of differential scanning calorimetry (DSC) to measure the thermal behavior of individual components and electrolyte/electrode combinations is common. However, here we focus on DSC tests on an anode, cathode, and electrolyte (ACE) component combination over a temperature range that includes many of the phase transitions and key reactions (i.e., to 500 °C) that contribute to thermal runaway. This method can help quantify the complex reaction network in a full cell, thereby informing potential safety issues. Here, we used DSC heat flow data from a solid-state Li 0.43 CoO 2 +C+PVDF | LLZO | Li metal ACE sample and its components to quantify key factors affecting results. We focused on three areas: (1) ACE sample preparation and assembly in DSC pans, (2) DSC measurement parameters, and (3) heat flow analysis. Key points include the choice of component ratios (e.g., commercially relevant N:P capacity ratio), the importance of conductive carbon and binder, type of pan used, DSC ramp rate, and integration method used when dealing with broad and overlapping exothermic peaks. This work deepens the scientific basis and best practices for obtaining heat flow data from ACE samples for early-stage evaluation of solid-state and beyond battery safety.

25 ENERGY STORAGE↗

DOE OSTI2020

Progress on Advancing the Robotic Air-slot Volumetric Inspection System (RAVIS) for Hanford Under-tank Inspection - 20519

The 27 in-service double-shell tank (DST) systems at Hanford provide interim storage for nearly 56 million gallons of nuclear and hazardous chemical legacy waste. The safe and reliable storage of the waste is critical to the site's extended cleanup mission. While in service, the leak integrity of the DSTs must be demonstrated to satisfy the Washington Administrative Code, inform decisions on tank management, and gauge fitness for continued service beyond originally intended design lives. The carbon steel plates and welds that comprise DST primary tank sidewalls and lower knuckles are routinely 'sampled' for volumetric non-destructive testing using ultrasonic inspection technology to determine whether corrosion pitting, cracking, or general corrosion are occurring that could compromise tank leak integrity. However, the carbon steel plates and welds that comprise the bottoms of primary tanks have not been thoroughly inspected since the DSTs were constructed (i.e., since 1968-1986) due to limited physical access to the exterior tank bottoms. The Robotic Air-slot Volumetric Inspection System, or 'RAVIS,' is being engineered to overcome the challenge of tank bottom in-service inspection. The system will be deployed under primary tanks within the small cooling channels/air-slots in the refractory pads upon which the tanks rest and will use ultrasonic guided wave inspection technology to volumetrically inspect physically inaccessible regions that make up ∼90% of a tank bottom, as well as regions that are physically accessible from the air-slots but comprise only ∼10% of a tank bottom. This paper describes the air-slot sensor and robotic deployment system and focuses on the testing approach and methods that are being applied to support (1) design feedback and performance acceptance (requirement verification) and (2) performance repeatability/reliability assessments (qualification) to ensure the RAVIS is prepared for successful inservice inspections of primary tank bottoms. Test progress made against the test plan, the results of 2019 testing, and the future outlook are included. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Characterization and integration of the singular test integrals in the method-of-moments implementation of the electric-field integral equation

In this paper, we characterize the logarithmic singularities arising in the method of moments from the Green’s function in integrals over the test domain, and we use two approaches for designing geometrically symmetric quadrature rules to integrate these singular integrands. These rules exhibit better convergence properties than quadrature rules for polynomials and, in general, lead to better accuracy with a lower number of quadrature points. In this work, we demonstrate their effectiveness for several examples encountered in both the scalar and vector potentials of the electric-field integral equation (singular, near-singular, and far interactions) as compared to the commonly employed polynomial scheme and the double Ma–Rokhlin–Wandzura (DMRW) rules, whose sample points are located asymmetrically within triangles.

42 ENGINEERING↗

DOE OSTI2026

Synthetic data-driven deep learning for label-free autonomous atomic force microscopy

Atomic force microscopy (AFM) is a widely used tool for nanoscale characterization across materials science, energy research, and biology. However, its adoption in high-throughput materials discovery and statistically driven studies remains limited by a strong dependence on expert operator input and by the scarcity of annotated experimental AFM datasets needed to enable data-driven automation. Here, we introduce SimuScan, a synthetic-data–driven framework that enables reliable AFM feature identification, segmentation, and targeted imaging without requiring large manually labeled experimental datasets. SimuScan generates tunable, high-fidelity synthetic AFM images of defined morphologies while incorporating realistic experimental artifacts, including tip–sample convolution, noise, flattening distortions, and surface debris. These datasets are shown to support scalable, label-free training of modern deep learning models for AFM analysis. When integrated into data-driven AFM workflows, SimuScan-trained models can locate and analyze nanoscale structures across large datasets and guide targeted follow-up imaging. We validate this approach on nanostructured surfaces, DNA assemblies, and bacterial cells, demonstrating robust generalization across diverse sample types with minimal operator intervention. More broadly, this work establishes a general strategy for generating explicitly conditioned, task-relevant synthetic data to improve the reliability of downstream models in autonomous microscopy.

Millan-Solsona, Ruben [Oak Ridge National Laborato↗

DOE OSTI2022

Substructure in the stellar halo near the Sun: I. Data-driven clustering in integrals-of-motion space

Context. Merger debris is expected to populate the stellar haloes of galaxies. In the case of the Milky Way, this debris should be apparent as clumps in a space defined by the orbital integrals of motion of the stars. Aims. Our aim is to develop a data-driven and statistics-based method for finding these clumps in integrals-of-motion space for nearby halo stars and to evaluate their significance robustly. Methods. We used data from Gaia EDR3, extended with radial velocities from ground-based spectroscopic surveys, to construct a sample of halo stars within 2.5 kpc from the Sun. We applied a hierarchical clustering method that makes exhaustive use of the single linkage algorithm in three-dimensional space defined by the commonly used integrals of motion energy E, together with two components of the angular momentum, L z and L ⊥ . To evaluate the statistical significance of the clusters, we compared the density within an ellipsoidal region centred on the cluster to that of random sets with similar global dynamical properties. By selecting the signal at the location of their maximum statistical significance in the hierarchical tree, we extracted a set of significant unique clusters. By describing these clusters with ellipsoids, we estimated the proximity of a star to the cluster centre using the Mahalanobis distance. Additionally, we applied the HDBSCAN clustering algorithm in velocity space to each cluster to extract subgroups representing debris with different orbital phases. Results. Our procedure identifies 67 highly significant clusters (> 3σ), containing 12% of the sources in our halo set, and 232 subgroups or individual streams in velocity space. In total, 13.8% of the stars in our data set can be confidently associated with a significant cluster based on their Mahalanobis distance. Inspection of the hierarchical tree describing our data set reveals a complex web of relations between the significant clusters, suggesting that they can be tentatively grouped into at least six main large structures, many of which can be associated with previously identified halo substructures, and a number of independent substructures. This preliminary conclusion is further explored in a companion paper, in which we also characterise the substructures in terms of their stellar populations. Conclusions. Our method allows us to systematically detect kinematic substructures in the Galactic stellar halo with a data-driven and interpretable algorithm. The list of the clusters and the associated star catalogue are provided in two tables available at the CDS.

79 ASTRONOMY AND ASTROPHYSICS↗