Search NASA⌕ Search

SEARCH · Search NASA

Results for “stack sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Ranking of Chemicals Measured in Emissions from R&D Facilities

The Pacific Northwest National Laboratory (PNNL) operates a number of multidisciplinary laboratory research facilities for the U. S. Department of Energy and has sampled air chemical emissions from some of these facilities since 1998. The primary purpose of this sampling is to obtain data to compare estimated release fractions to those used for emissions estimates, verifying that methods used to determine compliance with air regulations and permits conservatively predict actual emissions. Sampling also identifies and quantifies emissions of air toxics to compare with compliance limits established by regulatory agencies. Hundreds of samples have been taken from four different buildings (325, 329, 331, and EMSL) over a 10-year time period. Results from initial sampling campaigns were evaluated and reported by Woodruff, Benar, and McCarthy (2000) who summarized the compliance approach used by PNNL and described sampling and analytical measurements for the first sampling campaigns. Conclusions reported in this paper were that none of the measurements of the target compounds exceeded an acceptable source impact level (ASIL) (Washington Administrative Code, Chapter 173-460) even using significant overestimation factors, and that an average release fraction calculated from the data provided reasonable validation of the factor used in compliance assessments. Subsequent analysis compared chemical signatures from the buildings (Ballinger, Duchsherer, and Metoyer 2008). Results from this analysis showed that stack emissions from three of the four buildings had relatively similar chemical signatures but the fourth building differed from the other three significantly using the developed metric. This paper presents additional analyses of the measured air chemical emissions to 1) rank the chemical compounds that present the greatest risk to a potential downstream receptor and 2) determine whether the sampling parameters and detection limits provided sufficient resolution to verify compliance at potential receptor locations. The ranking method includes chemical-specific parameters such as measured concentrations, detection limits, and regulatory limits plus building-specific parameters such as location, stack flow-rate, and distance to receptors.

54 ENVIRONMENTAL SCIENCES↗

Use of in-situ TEM to characterize the deformation-induced martensitic transformation in 304 stainless steel at cryogenic temperature

Highlights: • Unique experimental visualization of DIM transformation in 304SS in-situ in a TEM at cryogenic temperatures. • Three cases of DIM were captured in situ showing how stress and temperature are both effective on the transformation. • (i) formation of ε- martensite through overlapping/bundling of SFs (γ →SFs →ε), • (ii) direct (γ→ α’) transformation with interface migration upon pulling the sample at constant temperature, • (iii) direct γ→ α’ transformation upon cooling, without further pulling the sample. - Abstract: Tensile tests are conducted in-situ in a TEM at cryogenic temperatures (from − 100 °C to 0 °C) using a cooling TEM straining-stage with the goal of capturing the growth of the martensitic phase as it develops under stress in the material. The in-situ technique is used to explore the mechanism of deformation induced martensitic transformation in 304 and 304L austenitic stainless steels. The formation of stacking faults is captured, as well as the subsequent formation of ε-martensite, confirming the role played by Stacking faults (SFs) as intermediate step during the transformation from γ-austenite to ε-martensite. In addition, direct transformation from γ-austenite to α′-martensite is captured (i) upon straining at a fixed temperature and (ii) upon cooling after pulling on the sample, indicating how straining and temperature are both effective on the transformation.

36 MATERIALS SCIENCE↗

Photoluminescence study of p-type vs. n-type Ag-doped ZnO films

Silver doped ZnO films have been grown on sapphire (0001) substrates by pulsed laser deposition. Hall measurements indicate that p-type conductivity is realized for the films deposited at 500 °C and 750 °C. Transmission electron microscopy images show more obvious and higher density of stacking faults (SFs) present in the p-type ZnO films as compared to the n-type films. Top view and cross sectional photoluminescence of the n- and p-type samples revealed free excitonic emission from both films. A peak at 3.314 eV, attributed to SF emission, has been observed only for the n-type sample, while a weak neutral acceptor peak observed at 3.359 eV in the p-type film. The SF emission in the n-type sample suggests localization of acceptor impurities nearby the SFs, while lack of SF emission for the p-type sample indicates the activation of the Ag acceptors in ZnO.

36 MATERIALS SCIENCE↗

Miniature Cryogenic Valves for a Titan Lake Sampling System

The Cassini mission has revealed Titan to be one of the most Earthlike worlds in the Solar System complete with many of the same surface features including lakes, river channels, basins, and dunes. But unlike Earth, the materials and fluids on Titan are composed of cryogenic organic compounds with lakes of liquid methane and ethane. One of the potential mission concepts to explore Titan is to land a floating platform on one of the Titan Lakes and determine the local lake chemistry. In order to accomplish this within the expected mass volume and power budgets there is a need to pursue the development for a low power lightweight cryogenic valves which can be used along with vacuum lines to sample lake liquid and to distribute to various instruments aboard the Lander. To meet this need we have initiated the development of low power cryogenic valves and actuators based on a single crystal piezoelectric flextensional stacks produced by TRS Ceramics Inc. Since the origin of such high electromechanical properties of Relaxor-PT single crystals is due to the polarization rotation effect, (i.e., intrinsic contributions), the strain per volt decrease at cryogenic temperatures is much lower than in standard Lead Zirconate Titanate (PZT) ceramics. This makes them promising candidates for cryogenic actuators with regards to the stroke for a given voltage. This paper will present our Titan Lake Sampling and Sample Handling system design and the development of small cryogenic piezoelectric valves developed to meet the system specifications.

Piezoelectric Devices↗

RAPID DETERMINATION OF ACTINIDES IN URINE BY INDUCTIVELY-COUPLED PLASMA MASS SPECTROMETRY AND ALPHA SPECTROMETRY: A HYBRID APPROACH

A new rapid separation method that allows separation and preconcentration of actinides in urine samples was developed for the measurement of longer lived actinides by inductively coupled plasma mass spectrometry (ICP-MS) and short-lived actinides by alpha spectrometry; a hybrid approach. This method uses stacked extraction chromatography cartridges and vacuum box technology to facilitate rapid separations. Preconcentration, if required, is performed using a streamlined calcium phosphate precipitation. Similar technology has been applied to separate actinides prior to measurement by alpha spectrometry, but this new method has been developed with elution reagents now compatible with ICP-MS as well. Purified solutions are split between ICP-MS and alpha spectrometry so that long- and short-lived actinide isotopes can be measured successfully. The method allows for simultaneous extraction of 24 samples (including QC samples) in less than 3 h. Simultaneous sample preparation can offer significant time savings over sequential sample preparation. For example, sequential sample preparation of 24 samples taking just 15 min each requires 6 h to complete. The simplicity and speed of this new method makes it attractive for radiological emergency response. If preconcentration is applied, the method is applicable to larger sample aliquots for occupational exposures as well. The chemical recoveries are typically greater than 90%, in contrast to other reported methods using flow injection separation techniques for urine samples where plutonium yields were 70-80%. This method allows measurement of both long-lived and short-lived actinide isotopes. 239Pu, 242Pu, 237Np, 243Am, 234U, 235U and 238U were measured by ICP-MS, while 236Pu, 238Pu, 239Pu, 241Am, 243Am and 244Cm were measured by alpha spectrometry. The method can also be adapted so that the separation of uranium isotopes for assay is not required, if uranium assay by direct dilution of the urine sample is preferred instead. Multiple vacuum box locations may be set-up to supply several ICP-MS units with purified sample fractions such that a high sample throughput may be achieved, while still allowing for rapid measurement of short-lived actinides by alpha spectrometry.

74 ATOMIC AND MOLECULAR PHYSICS↗

Astrobiological Potential of Rocks Acquired By the Perseverance Rover in Jezero Crater, Mars

The scientific community has prioritized the return of Martian rock samples with known geologic context for more than a decade (Beatty et al., 2019). Thus, the main objectives of the Perseverance rover mission on Mars include identifying past habitable environments, collecting rocks that are likely to preserve biosignaturesand using the rover’s instruments to look for potential biosignatures in these rocks (Farley et al., 2020). Here, we present an overview of the bedrock samples collected bythe Perseverance rover in Jezero crater to date and discuss the potential of the sampled materials to address astrobiological questions upon sample return to Earth.

Mars 2020↗

Experimental study of three-dimensional CO 2 -water drainage and fracture-matrix interactions in fractured porous media

Estimation of CO 2 storage capacity in fractured porous reservoirs requires a better understanding of the CO 2 -water flow fundamentals in fracture-matrix systems. There are few core-flood experiments on three-dimensional CO 2 -water drainage in a fracture-matrix system, yet none have examined the impacts of the capillary continuity of fractures and fracture-matrix interactions. In this study, twelve drainage experiments were conducted in four fracture-matrix columns, each comprising a vertical stack of a cylindrical rock core, a filter paper serving as an analogue to a horizontal fracture, and a ceramic plate. Here, the core sample was surrounded by open space at the top and circumferential sides to model fractures, allowing for 3-D CO 2 -water drainage in the rock core and displaced water draining across the horizontal fracture. X-ray computed tomography was conducted to visualize the dynamic invasion/drainage processes in four rock core samples showing contrasts in anisotropy, permeability, and heterogeneity. Experimental results show (1) the equilibrium CO 2 saturations in the rock matrix vary from 0.10 to 0.60 at controlled capillary pressures up to 200 kPa, (2) the CO 2 saturations in the matrix increase with water saturation in the horizontal fracture resulting in better capillary continuity for water to drain across the fracture, and (3) the fracture water saturation can be enhanced by the non-uniform fracture capillary pressure and countercurrent flow of CO 2 and water across the fracture-matrix interface. In the case of high fracture water saturation, matrix CO 2 saturation largely depends on matrix anisotropy and heterogeneity. The core-scale experimental results contribute to understand the fracture-matrix interactions and CO 2 storage efficiency in fractured porous media.

54 ENVIRONMENTAL SCIENCES↗

No correlation of the Lyman continuum escape fraction with spectral hardness

The properties that govern the production and escape of hydrogen-ionizing photons (Lyman continuum, LyC; with energies > 13.6 eV) in star-forming galaxies are still poorly understood, but they are key to identifying and characterizing the sources that reionized the Universe. Here we empirically explore the relation between the hardness of ionizing radiation and the LyC leakage in a large sample of low- z star-forming galaxies from the recent Hubble Space Telescope Low- z Lyman Continuum Survey. Using Sloan Digital Sky Survey stacks and deep X-shooter observations, we investigate the hardness of the ionizing spectra ( Q He + / Q H ) between 54.4 eV (He + ) and 13.6 eV (H) from the optical recombination lines He II 4686 Å and Hβ 4861 Å for galaxies with LyC escape fractions spanning a wide range, f esc (LyC) ≃ 0–90%. We find that the observed intensity of He II/Hβ is primarily driven by variations in the metallicity, but is not correlated with LyC leakage. Both very strong (< f esc (LyC)> ≃ 0.5) and nonleakers (< f esc (LyC)> ≃ 0) present similar observed intensities of He II and Hβ at comparable metallicity, between ≃0.01 and ≃0.02 for 12 + log(O/H)> 8.0 and < 8.0, respectively. Our results demonstrate that Q He + / Q H does not correlate with f esc (LyC), which implies that strong LyC emitters do not show harder ionizing spectra than nonleakers at similar metallicity.

79 ASTRONOMY AND ASTROPHYSICS↗

Mapping Impervious Surface Expansion using Medium-resolution Satellite Image Time Series: A Case Study in the Yangtze River Delta, China

Cities have been expanding rapidly worldwide, especially over the past few decades. Mapping the dynamic expansion of impervious surface in both space and time is essential for an improved understanding of the urbanization process, land-cover and land-use change, and their impacts on the environment. Landsat and other medium-resolution satellites provide the necessary spatial details and temporal frequency for mapping impervious surface expansion over the past four decades. Since the US Geological Survey opened the historical record of the Landsat image archive for free access in 2008, the decades-old bottleneck of data limitation has gone. Remote-sensing scientists are now rich with data, and the challenge is how to make best use of this precious resource. In this article, we develop an efficient algorithm to map the continuous expansion of impervious surface using a time series of four decades of medium-resolution satellite images. The algorithm is based on a supervised classification of the time-series image stack using a decision tree. Each imerpervious class represents urbanization starting in a different image. The algorithm also allows us to remove inconsistent training samples because impervious expansion is not reversible during the study period. The objective is to extract a time series of complete and consistent impervious surface maps from a corresponding times series of images collected from multiple sensors, and with a minimal amount of image preprocessing effort. The approach was tested in the lower Yangtze River Delta region, one of the fastest urban growth areas in China. Results from nearly four decades of medium-resolution satellite data from the Landsat Multispectral Scanner (MSS), Thematic Mapper (TM), Enhanced Thematic Mapper plus (ETM+) and China-Brazil Earth Resources Satellite (CBERS) show a consistent urbanization process that is consistent with economic development plans and policies. The time-series impervious spatial extent maps derived from this study agree well with an existing urban extent polygon data set that was previously developed independently. The overall mapping accuracy was estimated at about 92.5% with 3% commission error and 12% omission error for the impervious type from all images regardless of image quality and initial spatial resolution.

Gao, Feng↗

Controlling the oriented growth of Ti{sub 2}SnC grains with carbon fiber as a reactive template in the Ti-Sn-C system

Carbon short fibers with a length of {approx}3 mm used as a reactive template were mixed with Ti and Sn powders. The mixture was pressurelessly sintered at 1200 deg. C for 2 h in a vacuum atmosphere. The microstructure shows that Ti{sub 2}SnC grains with a plate-like shape grow along a preferred direction, forming a 'string' structure in which Ti{sub 2}SnC platelets pack themselves closely with a top-bottom-top-bottom sequence. With increasing the length of the C fibers, the length of the 'string' structures increases. A large amount of long and aligned 'string' structures have formed after sintering the samples prepared by infiltration of the carbon short fibers with a length of {approx}50 mm in a Ti-Sn slurry and then stacking and cold pressing. X-ray diffraction and scanning electron microscopy, respectively were used to analyze and observe the phase composition and microstructure.

36 MATERIALS SCIENCE↗

Interaction of coal-derived synthesis gas impurities with solid oxide fuel cell metallic components

Chromium-containing iron-based alloys Crofer22 APU and SS 441 and nickel-based alloy Inconel600, all commonly used in a solid oxide fuel cell (SOFC) stack as interconnect materials, heat exchanger and gas feeding pipes, were exposed at 700-850oC to a synthetic coal gas containing ≤2 ppm phosphine, arsine, sulfur and antimony. Samples were characterized by SEM/EDS and XRD to monitor the secondary phase formation. Exposure of ferritic stainless steels to P led to the formation of surface Cr-Mn-P-O and Fe-P-O compounds and increased temperatures accelerated the rate of interactions. Fewer interactions were observed after exposures to As and Sb. No sulfur containing compounds were found. Nickel-based alloy exhibited much stronger interactions with As and P in comparison with ferritic steels and the arsenic interactions were particularly strong. The difference between the iron- and nickel-based alloys is explained by the different chemistry and morphology of the scales grown on the alloy surfaces in coal gas. While P and As interactions with the metallic parts in the SOFC are likely to mitigate the nickel/zirconia anode poisoning, the other degradation mechanisms should be taken into consideration to avoid potential stack failures. Manganese spinels were found to be effective as phosphorus getters and could be used in coal gas cleanup.

01 COAL, LIGNITE, AND PEAT↗

Development and Experimental Evaluation of Passive Fuel Cell Thermal Control

To provide uniform cooling for a fuel cell stack, a cooling plate concept was evaluated. This concept utilized thin cooling plates to extract heat from the interior of a fuel cell stack and move this heat to a cooling manifold where it can be transferred to an external cooling fluid. The advantages of this cooling approach include a reduced number of ancillary components and the ability to directly utilize an external cooling fluid loop for cooling the fuel cell stack. A number of different types of cooling plates and manifolds were developed. The cooling plates consisted of two main types; a plate based on thermopyrolytic graphite (TPG) and a planar (or flat plate) heat pipe. The plates, along with solid metal control samples, were tested for both thermal and electrical conductivity. To transfer heat from the cooling plates to the cooling fluid, a number of manifold designs utilizing various materials were devised, constructed, and tested. A key aspect of the manifold was that it had to be electrically nonconductive so it would not short out the fuel cell stack during operation. Different manifold and cooling plate configurations were tested in a vacuum chamber to minimize convective heat losses. Cooling plates were placed in the grooves within the manifolds and heated with surface-mounted electric pad heaters. The plate temperature and its thermal distribution were recorded for all tested combinations of manifold cooling flow rates and heater power loads. This testing simulated the performance of the cooling plates and manifold within an operational fuel cell stack. Different types of control valves and control schemes were tested and evaluated based on their ability to maintain a constant temperature of the cooling plates. The control valves regulated the cooling fluid flow through the manifold, thereby controlling the heat flow to the cooling fluid. Through this work, a cooling plate and manifold system was developed that could maintain the cooling plates within a minimal temperature band with negligible thermal gradients over power profiles that would be experienced within an operating fuel cell stack.

Fuel Cells↗

Dark Energy Survey Year 3 results: Measurement of the baryon acoustic oscillations with three-dimensional clustering

The three-dimensional correlation function offers an effective way to summarize the correlation of the large-scale structure even for imaging galaxy surveys. We have applied the projected three-dimensional correlation function, ξ p to measure the baryonic acoustic oscillations (BAO) scale on the first-three years Dark Energy Survey data. The sample consists of about 7 million galaxies in the redshift range 0.6< z p < 1.1 over a footprint of 4108 deg 2 . Our theory modeling includes the impact of realistic true redshift distributions beyond Gaussian photo-z approximation. ξ p is obtained by projecting the three-dimensional correlation to the transverse direction. To increase the signal-to-noise of the measurements, we have considered a Gaussian stacking window function in place of the commonly used top-hat. ξ p is sensitive to D M (z eff )/r s , the ratio between the comoving angular diameter distance and the sound horizon. Using the full sample, D M (z eff )/r s is constrained to be19.00 ± 0.67 (top-hat) and 19.15 ± 0.58 (Gaussian) at z eff = 0.835. The constraint is weaker than the angular correlation w constraint 18.84 ± 0.50), and we trace this to the fact that the BAO signals are heterogeneous across redshift. While ξ p responds to the heterogeneous signals by enlarging the error bar, w can still give a tight bound on D M s in this case. When a homogeneous BAO-signal subsample in the range 0.7 < z p <1.0 (z eff = 0.845) is considered, ξp yields 19.80 ± 0.67 (top-hat) and 19.84 ± 0.53 (Gaussian). The latter is mildly stronger than the w constraint (19.86 ± 0.55). We find that the ξ p results are more sensitive to photo-z because ξ p keeps the three-dimensional clustering information causing it to be more prone to photo-z noise. The Gaussian window gives more robust results than the top-hat as the former is designed to suppress the low signal modes. ξ p and the angular statistics such as w have their own pros and cons, and they serve an important crosscheck with each other.

79 ASTRONOMY AND ASTROPHYSICS↗

RAPID DETERMINATION OF 237 NP AND PU ISOTOPES IN WATER BY INDUCTIVELY COUPLED PLASMA MASS SPECTROMETRY AND ALPHA SPECTROMETRY

A new method that allows rapid preconcentration and separation of plutonium and neptunium in water samples was developed for the measurement of {sup 237}Np and Pu isotopes by inductively-coupled plasma mass spectrometry (ICP-MS) and alpha spectrometry; a hybrid approach. {sup 238}U can interfere with {sup 239}Pu measurement by ICP-MS as {sup 238}UH{sup +} mass overlap and {sup 237}Np via peak tailing. The method provide enhanced removal of uranium by separating Pu and Np initially on TEVA Resin, then moving Pu to DGA resin for additional removal of uranium. The decontamination factor for uranium from Pu is almost 100,000 and the decontamination factor for U from Np is greater than 10,000. This method uses stacked extraction chromatography cartridges and vacuum box technology to facilitate rapid separations. Preconcentration is performed using a streamlined calcium phosphate precipitation method. Purified solutions are split between ICP-MS and alpha spectrometry so that long and short-lived Pu isotopes can be measured successfully. The method allows for simultaneous extraction of 20 samples (including QC samples) in 4 to 6 hours, and can also be used for emergency response. {sup 239}Pu, {sup 242}Pu and {sup 237}Np were measured by ICP-MS, while {sup 236}Pu, {sup 238}Pu, and {sup 239}Pu were measured by alpha spectrometry.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Influence of Structural Defects on Biomineralized ZnS Nanoparticle Dissolution: An In-Situ Electron Microscopy Study

The dissolution of metal sulfides, such as ZnS, plays an important role in the fate of metal contaminants in the environment. Here we have examined the dissolution behavior of ZnS nanoparticles synthesized via several abiotic and biological pathways. Specifically, the biogenic ZnS nanoparticles were produced by an anaerobic, metal-reducing bacterium Thermoanaerobacter sp. X513 in a Zn-amended, thiosulfate-containing growth medium, whereas the abiogenic ZnS nanoparticles were produced by mixing an aqueous Zn solution with either H 2 S-rich gas or Na 2 S solution. For biogenic synthesis, we prepared two types of samples, in the presence or absence of trace silver (Ag). The size distribution, crystal structure, aggregation behavior, and internal defects of the synthesized ZnS nanoparticles were primarily examined using high-resolution transmission electron microscopy coupled with X-ray energy dispersive spectroscopy. The characterization results show that both the biogenic and abiogenic samples were dominantly composed of sphalerite. In the absence of Ag, the biogenic ZnS nanoparticles were significantly larger (i.e., ~10 nm) than the abiogenic ones (i.e., ~3–5 nm) and contained structural defects (e.g., twins and stacking faults). The presence of trace Ag showed a restraining effect on the particle size of the biogenic ZnS, resulting in quantum-dot-sized nanoparticles (i.e., ~3 nm). In situ dissolution experiments for the synthesized ZnS were conducted with a liquid-cell coupled to a transmission electron microscope (LCTEM), and the primary factors (i.e., the presence or absence structural defects) were evaluated for their effects on the dissolution behavior using the biogenic and abiogenic ZnS nanoparticle samples with the largest average particle size. Analysis of the dissolution results (i.e., change in particle radius with time) using the Kelvin equation shows that the defect-bearing biogenic ZnS nanoparticles (γ = 0.799 J/m 2 ) have a significantly higher surface energy than the abiogenic ZnS nanoparticles (γ = 0.277 J/m 2 ), suggesting that larger defect-bearing ZnS nanoparticles may be more reactive than the smaller quantum-dot-sized ZnS nanoparticles. These findings provide new insight into the factors that govern the dissolution of metal sulfide nanoparticles in relevant natural and engineered scenarios, and have implication for tracking the fate of zinc at contaminated sites. Moreover, our study exemplified the use of an in situ method (i.e., LCTEM) to investigate nanoparticle behavior (e.g., dissolution) in aqueous solutions.

54 ENVIRONMENTAL SCIENCES↗

Redshift evolution of the H I detection rate in radio-loud active galactic nuclei

We present a search for associated H I 21 cm absorption in a sample of 29 radio-loud active galactic nuclei (AGNs) at 0.7 < z < 1, carried out with the upgraded Giant Metrewave Radio Telescope. We detect H I 21 cm absorption against none of our target AGNs, obtaining 3σ upper limits to the optical depth of ≲1% per 50 km s –1 channel. The radio luminosity of our sources is lower than that of most AGNs searched for H I 21 cm absorption at similar redshifts in the literature, and, for all targets except two, the UV luminosity is below the threshold 10 23 W Hz –1 , above which the H I in the AGN environment has been suggested to be completely ionised. We stacked the H I 21 cm spectra to obtain a more stringent limit of ≈0.17% per 50 km s –1 channel on the average H I 21 cm optical depth of the sample. Furthermore, the sample is dominated by extended radio sources, 24 of which are extended on scales of tens of kiloparsecs. Including similar extended sources at 0.7 < z < 1.0 from the literature, and comparing with a low-z sample of extended radio sources, we find statistically significant (≈3σ) evidence that the strength of H I 21 cm absorption towards extended radio sources is weaker at 0.7 < z < 1.0 than at z < 0.25, with a lower detection rate of H I 21 cm absorption at 0.7 < z < 1.0. Redshift evolution in the physical conditions of H I is the likely cause of the weaker associated H I 21 cm absorption at high redshifts, due to either a low H I column density or a high spin temperature in high-z AGN environments.

79 ASTRONOMY AND ASTROPHYSICS↗

Thermochemical and kinetic aspects of the sulfurization of Cu-Sb and Cu-Bi thin films

CuSbS{sub 2} and Cu{sub 3}BiS{sub 3} are being investigated as part of a search for new absorber materials for photovoltaic devices. Thin films of these chalcogenides were produced by conversion of stacked and co-electroplated metal precursor layers in the presence of elemental sulfur vapour. Ex-situ XRD and SEM/EDS analyses of the processed samples were employed to study the reaction sequence with the aim of achieving compact layer morphologies. A new 'Time-Temperature-Reaction' (TTR) diagram and modified Pilling-Bedworth coefficients have been introduced for the description and interpretation of the reaction kinetics. For equal processing times, the minimum temperature required for CuSbS{sub 2} to appear is substantially lower than for Cu{sub 3}BiS{sub 3}, suggesting that interdiffusion across the interfaces between the binary sulfides is a key step in the formation of the ternary compounds. The effects of the heating rate and sulfur partial pressure on the phase evolution as well as the potential losses of Sb and Bi during the processes have been investigated experimentally and the results related to the equilibrium pressure diagrams obtained via thermochemical computation. - Graphical Abstract: Example of 3D plot showing the equilibrium pressure surfaces of species potentially escaping from chalcogenide films as a function of temperature and sulfur partial pressure. Bi{sub (g)}, Bi{sub 2(g)}, and BiS{sub (g)} are the gaseous species in equilibrium with solid Bi{sub 2}S{sub 3(s)} considered in this specific example. The pressure threshold plane corresponds to the pressure limit above which the elemental losses from 1 {mu}m thick films exceeds 10% of the original content per cm{sup 2} area of film and dm{sup 3} capacity of sulfurization furnace under static atmosphere conditions. The sulfurization temperature/sulfur partial pressure boundaries required to minimise the elemental losses below a given value can be easily read from the 2D projection of the intersection curves into the T-p{sub S2} plane. Highlights: Black-Right-Pointing-Triangle Sulfurization of Sb-Cu and Bi-Cu metal precursors for thin film PV applications. Black-Right-Pointing-Triangle Kinetics shows the rate determining step to be the interdiffusion of binary sulfides. Black-Right-Pointing-Triangle Phase evolution is consistent with Pilling-Bedworth coefficients of Cu, Sb and Bi. Black-Right-Pointing-Triangle Elemental losses can be minimised via the use of equilibrium pressure diagrams.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-temperature oxidation of transient-liquid phase bonded Ni-based alloys in 1 bar and 250 bar carbon dioxide

Compact microchannel heat exchanger designs for supercritical CO 2 power cycles are valued for equipment size reduction and increased heat transfer. They can be fabricated via transient-liquid phase (TLP) bonding, which utilizes a lower melting point interlayer for bonding facilitation of etched thin plates. Haynes 230 and 282 TLP bonded stacks were exposed to high-purity CO 2 at 1 bar/700 °C to 4000 h and 250 bar/720 °C (supercritical) to 1500 h. All samples obeyed parabolic kinetics after an oxide buildup stage of 500-1000 h. Mass gains were similar for the base and TLP bonded alloys, and oxide thicknesses and scales did not significantly differ around the TLP bond regions. Furthermore, there were some slight oxide compositional differences for the H282 TLP samples at 250 bar. There was a slight pressure effect on mass gain, as samples exposed at the higher pressure experienced higher initial mass gains, but then slower continued oxide growth.

36 MATERIALS SCIENCE↗