Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal protection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Galileo probe forebody entry thermal protection - Aerothermal environments and heat shielding requirements

Solutions are presented for the aerothermal heating environments and the material thermal response for the forebody heatshield on the candidate 242 kg Galileo probe entering the modeled nominal and cold-dense Jovian atmospheres. In the flowfield analysis, a finite difference procedure was employed to obtain benchmark predictions of pressure, radiation and convective heating rates (both laminar and turbulent) and the corresponding wall blowing obtained under the steady state approximation. The fluxes over the probe flank were found to be in a range where spallation is an important mass loss mechanism. The predicted heating rates were also used as boundary conditions for a charring materials ablation which was used to predict thermochemical based surface recession, mass loss and bondline temperatures. The contingency factor of 30% currently employed by NASA was found to be insufficient for entry into the cold-dense atmosphere.

Nicolet, W. E.↗
NASA NTRS2010

Ablation, Thermal Response, and Chemistry Program for Analysis of Thermal Protection Systems

In previous work, the authors documented the Multicomponent Ablation Thermochemistry (MAT) and Fully Implicit Ablation and Thermal response (FIAT) programs. In this work, key features from MAT and FIAT were combined to create the new Fully Implicit Ablation, Thermal response, and Chemistry (FIATC) program. FIATC is fully compatible with FIAT (version 2.5) but has expanded capabilities to compute the multispecies surface chemistry and ablation rate as part of the surface energy balance. This new methodology eliminates B' tables, provides blown species fractions as a function of time, and enables calculations that would otherwise be impractical (e.g. 4+ dimensional tables) such as pyrolysis and ablation with kinetic rates or unequal diffusion coefficients. Equations and solution procedures are presented, then representative calculations of equilibrium and finite-rate ablation in flight and ground-test environments are discussed.

Milos, Frank S.↗
NASA NTRS1979

SRB thermal protection systems materials test results in an arc-heated nitrogen environment

The external surface of the Solid Rocket Booster (SRB) will experience imposed thermal and shear environments due to aerodynamic heating and radiation heating during launch, staging and reentry. This report is concerned with the performance of the various TPS materials during the staging maneuver. During staging, the wash from the Space Shuttle Main Engine (SSME) exhust plumes impose severe, short duration, thermal environments on the SRB. Five different SRB TPS materials were tested in the 1 MW Arc Plasma Generator (APG) facility. The maximum simulated heating rate obtained in the APG facility was 248 Btu/sq ft./sec, however, the test duration was such that the total heat was more than simulated. Similarly, some local high shear stress levels of 0.04 psia were not simulated. Most of the SSME plume impingement area on the SRB experiences shear stress levels of 0.02 psia and lower. The shear stress levels on the test specimens were between 0.021 and 0.008 psia. The SSME plume stagnation conditions were also simulated.

Wojciechowski, C. J.↗
NASA NTRS2005

Thermal Protection of the Huygens Probe During Titan Entry: Last Questions

CASSINI-HUYGENS mission is a cooperation between NASA and ESA, dedicated to the exploration of the Saturnian system. In the framework of this mission, the entry of the HUYGENS probe in the atmosphere of TITAN will be of major scientific interest. One of the essential points of the HUYGENS mission is therefore the good behavior of the thermal shield designed to maintain the aerodynamic shape and to protect the probe from excessive heating during the atmospheric entry on TITAN. The design and the qualification of this thermal shield were carried out between 1992 and 1995 (development phase). Currently, the final definition of mission parameters is being completed. As the performance of the thermal shield is one of all the parameters considered at system level, it is therefore necessary to reassess the thermal response of the TPS, taking into account some updated information that was not yet available during the development phase. After some recall of the results of 1992 to 1995, the paper will present a status of the current work on TPS.

Bouilly, Jean-Marc↗
NASA NTRS1997

Evaluation of Thermal Control Coatings for Flexible Ceramic Thermal Protection Systems

This report summarizes the evaluation and testing of high emissivity protective coatings applied to flexible insulations for the Reusable Launch Vehicle technology program. Ceramic coatings were evaluated for their thermal properties, durability, and potential for reuse. One of the major goals was to determine the mechanism by which these coated blanket surfaces become brittle and try to modify the coatings to reduce or eliminate embrittlement. Coatings were prepared from colloidal silica with a small percentage of either SiC or SiB6 as the emissivity agent. These coatings are referred to as gray C-9 and protective ceramic coating (PCC), respectively. The colloidal solutions were either brushed or sprayed onto advanced flexible reusable surface insulation blankets. The blankets were instrumented with thermocouples and exposed to reentry heating conditions in the Ames Aeroheating Arc Jet Facility. Post-test samples were then characterized through impact testing, emissivity measurements, chemical analysis, and observation of changes in surface morphology. The results show that both coatings performed well in arc jet tests with backface temperatures slightly lower for the PCC coating than with gray C-9. Impact testing showed that the least extensive surface destruction was experienced on blankets with lower areal density coatings.

Kourtides, Demetrius↗
NASA NTRSDate not supplied

Analysis of Pyrolysis Products from Ablative Thermal Protection Systems

NASA’s state-of-the-art ablative materials are composed of a three-dimensional network of carbon fibers impregnated with polymers that dissipate thermal energy through pyrolysis. A fundamental understanding of the decomposition mechanisms and pyrolysis product distributions of various classes of polymers is instrumental in the design of new ablative materials. Furthermore, innovative experiments are essential to the continuous modernization of material response models by providing high-fidelity data. Thus, an apparatus has been designed to measure pyrolysis products from polymers and composite materials by implementing in-situ mass spectrometric techniques. Initial results from experiments performed on siloxane resins and a common phenolic resin will be discussed. Both classes of polymers exhibit heating-rate-dependent decomposition mechanisms. At the onset of heating, phenolic polymers decompose through competitive reactions to form gaseous products and a carbonaceous char. Gas phase products of phenolic resins are typically composed of molecular hydrogen, water, and aromatic hydrocarbons. Pyrolysis products from siloxane polymers include molecular hydrogen, small molecules, and cyclic oligomers from the polymer backbone.

Pyrolysis↗
NASA NTRS1975

Large modular graphite radiant heaters for testing space shuttle thermal protection systems

A graphite radiant heating array, capable of heating a 5-ft span of shuttle wing leading edge or a 4 x 8 ft flat panel through an entry thermal profile up to 3200 G, has been designed and built by McDonnell Douglas Corporation for NASA-Johnson Space Center. The unique, interchangeable, self-contained heather modules and their versatile support structure/coolant manifold are discussed along with the extensive thermal analysis that accompanied the design effort. A complete description of the geometric capabilities of the array, as well as the design details of the individual modules, is presented. The complete performance envelope of the array is discussed, including maximum temperature and gradients, heating uniformity, and the required utilities and support equipment.

Cox, B. G.↗
NASA NTRS1989

Composite multilayer insulations for thermal protection of aerospace vehicles

Composite flexible multilayer insulation systems (MLI), consisting of alternating layers of metal foil and scrim cloth or insulation quilted together using ceramic thread, were evaluated for thermal performance and compared with a silica fibrous (baseline) insulation system. The systems studied included: (1) alternating layers of aluminoborosilicate (ABS) scrim cloth and stainless steel foil, with silica, ABS, or alumina insulation; (2) alternating layers of scrim cloth and aluminum foil, with silica or ABS insulation; (3) alternating layers of alumininum foil and silica or ABS insulation; and (4) alternating layers of aluminum-coated polyimide placed on the bottom of the silica insulation. The MLIs containing aluminum were the most efficient, measuring as little as half the backface temperature increase of the baseline system.

Kourtides, D. A.↗
NASA NTRS1989

Composite multilayer insulations for thermal protection of aerospace vehicles

Composite flexible multilayer insulation systems (MLI), consisting of alternating layers of metal foil and scrim cloth or insulation quilted together using ceramic thread, were evaluated for thermal performance and compared with a silica fibrous (baseline) insulation system. The systems studied included: (1) alternating layers of aluminoborosilicate (ABS) scrim cloth and stainless steel foil, with silica, ABS, or alumina insulation; (2) alternating layers of scrim cloth and aluminum foil, with silica or ABS insulation; (3) alternating layers of aluminum foil and silica or ABS insulation; and (4) alternating layers of aluminum-coated polyimide placed on the bottom of the silica insulation. The MLIs containing aluminum were the most efficient, measuring as little as half the backface temperature increase of the baseline system.

Kourtides, Demetrius A.↗
NASA NTRS1997

Inorganic Water Repellent Coatings for Thermal Protection Insulation on an Aerospace Vehicle

The objective of this research was two-fold: first, to identify and test inorganic water-repellent materials that would be hydrophobic even after thermal cycling to temperatures above 600 C and, second, to develop a model that would link hydrophobicity of a material to the chemical properties of its constituent atoms. Four different materials were selected for detailed experimental study, namely, boron nitride, talc, molybdenite, and pyrophyllite, all of which have a layered structure made up of ionic/covalent bonds within the layers but with van der Waals bonds between the layers. The materials tested could be considered hydrophobic for a nonporous surface but none of the observed contact angles exceeded the necessary 90 degrees required for water repellency of porous materials. Boron nitride and talc were observed to retain their water-repellency when heated in air to temperatures that did not exceed 800 C, and molybdenite was found to be retain its hydrophobicity when heated to temperatures up to 600 C. For these three materials, oxidation and decomposition were identified to be the main cause for the breakdown of water repellency after repeated thermal cycling. Pyrophyllite shows the maximum promise as a potential water-repellent inorganic material, which, when treated initially at 900 C, retained its shape and remained hydrophobic for two thermal cycles where the maximum retreatment temperature is 900 C. A model was developed for predicting materials that might exhibit hydrophobicity by linking two chemical properties, namely, that the constituent ions of the compound belong to the soft acid-base category and that the fractional ionic character of the bonds be less than about 20 percent.

Fuerstenau, D. W.↗
NASA NTRS1997

Inorganic Water Repellent Coatings for Thermal Protection Insulation on an Aerospace Vehicle

The objective of this research was two-fold: first, to identify and test inorganic water-repellent materials that would be hydrophobic even after thermal cycling to temperatures above 600 C and, second, to develop a model that would link hydrophobicity of a material to the chemical properties of its constituent atoms. Four different materials were selected for detailed experimental study, namely, boron nitride, talc, molybdenite, and pyrophyllite, all of which have a layered structure made up of ionic/covalent bonds within the layers but with van der Waals bonds between the layers. The materials tested could be considered hydrophobic for a nonporous surface but none of the observed contact angles exceeded the necessary 90 degrees required for water repellency of porous materials. Boron nitride and talc were observed to retain their water-repellency when heated in air to temperatures that did not exceed 800 C, and molybdenite was found to be retain its hydrophobicity when heated to temperatures up to 600 C. For these three materials, oxidation and decomposition were identified to be the main cause for the breakdown of water repellency after repeated thermal cycling. Pyrophyllite shows the maximum promise as a potential water-repellent inorganic material, which, when treated initially at 900 C, retained its shape and remained hydrophobic for two thermal cycles where the maximum retreatment temperature is 900 C. A model was developed for predicting materials that might exhibit hydrophobicity by linking two chemical properties, namely, that the constituent ions of the compound belong to the soft acid-base category and that the fractional ionic character of the bonds be less than about 20 percent.

Fuerstenau, D. W.↗
DOE OSTI2022

Influence of Thermal Treatment on Preceramic Polymer Grafted Nanoparticle Network Formation: Implications for Thermal Protection Systems and Aerospace Propulsion Components

Preceramic polymer grafted nanoparticles (PCP GNPs) offer potential advantages in the production of polymer-derived ceramic composites compared to neat preceramic polymers (PCPs), such as reduced thermal shrinkage and increased char yield. In comparison to traditional composites (particles + free polymer), PCPs avoid issues of compatibility, agglomeration, and phase separation during processing and provide routes to control nanoparticle arrangement. Prior literature has established that the conversion efficiency of PCPs and PCP GNPs to ceramics and ceramic composites is linked to the thermal pretreatment of these precursor polymers (e.g., curing). In this paper, we investigate the material transformations that occur when exposing PCP GNPs to a low-temperature thermal treatment (≤250 °C) prior to pyrolysis. The PCP GNPs explored in this study possessed silica nanoparticle cores but were distinct in their PCP coronas, having poly(1,1-dimethylpropylsilane) (allyl-GNP)- or poly(1,1-dimethylbenzylethylsilane) (styryl-GNP)-grafted polymers. After undergoing low-temperature thermal treatment, these PCP GNPs exhibited increased char yield at 800 °C; however, unlike commercial PCPs (e.g., allylhydridopolycarbosilane (SMP-10)), obvious cross-linkable sites are not present in the PCP corona structure. Differential scanning calorimetry, oscillatory rheology, and X-ray photon correlation spectroscopy were utilized to elucidate the thermally induced material changes in the allyl- and styryl-GNPs. Thermally induced changes to the structure and behavior of the PCP GNPs were determined to be linked to the chemical structure of the grafted polycarbosilane chains. Styryl-GNPs experienced a curing event between 180 and 250 °C, effecting the formation of a network, which contributed to char yield improvement (at 800 °C). The nanoscale dynamics of this material also shows a transition from diffuse behavior to ballistic behavior because of the cross-linking event. Conversely, the allyl-GNPs did not exhibit a curing event under heat treatment but did show an increase in thermally induced physical cross-linking. The allyl-GNP physical network is stronger after the first cycle of thermal treatment, and it is considered that this contributed to the improvement in char yield post thermal treatment. The advancements in the understanding of the cross-linking behavior of these hybrid materials are expected to advance the application of these materials to turbine engine, advanced friction, and heat-shielding components.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Fabrication of prepackaged superalloy honeycomb Thermal Protection System (TPS) panels

High temperature materials were surveyed, and Inconel 617 and titanium were selected for application to a honeycomb TPS configuration designed to withstand 2000 F. The configuration was analyzed both thermally and structurally. Component and full-sized panels were fabricated and tested to obtain data for comparison with analysis. Results verified the panel design. Twenty five panels were delivered to NASA Langley Research Center for additional evaluation.

Blair, W.↗
NASA NTRS1974

Analytical modeling of intumescent coating thermal protection system in a JP-5 fuel fire environment

The thermochemical response of Coating 313 when exposed to a fuel fire environment was studied to provide a tool for predicting the reaction time. The existing Aerotherm Charring Material Thermal Response and Ablation (CMA) computer program was modified to treat swelling materials. The modified code is now designated Aerotherm Transient Response of Intumescing Materials (TRIM) code. In addition, thermophysical property data for Coating 313 were analyzed and reduced for use in the TRIM code. An input data sensitivity study was performed, and performance tests of Coating 313/steel substrate models were carried out. The end product is a reliable computational model, the TRIM code, which was thoroughly validated for Coating 313. The tasks reported include: generation of input data, development of swell model and implementation in TRIM code, sensitivity study, acquisition of experimental data, comparisons of predictions with data, and predictions with intermediate insulation.

Clark, K. J.↗
NASA NTRS1985

Space Shuttle Main Engine nozzle thermal protection system

Two of the three Space Shuttle Main Engine (SSME) nozzles are exposed to significant reentry aeroheating loads. To ensure reusability of the Nozzle Assembly, the nozzle primary structure must not exceed specific temperature limits. Due to the thermal, pressure, and dynamic flexing of the nozzle during a mission cycle, an appropriate insulating system must have significant flexibility. Recent missions have demonstrated nozzle reentry aeroheating rates and heat loads much higher than predictions, higher than the capability of the original insulating system. A new insulating system has been developed using similar materials in an aerodynamically 'smooth' shape to both reduce the incoming heating and increase radiation cooling.

Nordlund, R. M.↗
NASA NTRS1979

Development and evaluation of an ablative closeout material for solid rocket booster thermal protection system

A trowellable closeout/repair material designated as MTA-2 was developed and evaluated for use on the Solid Rocket Booster. This material is composed of an epoxy-polysulfide binder and is highly filled with phenolic microballoons for density control and ablative performance. Mechanical property testing and thermal testing were performed in a wind tunnel to simulate the combined Solid Rocket Booster trajectory aeroshear and heating environments. The material is characterized by excellent thermal performance and was used extensively on the Space Shuttle STS-1 and STS-2 flight hardware.

Patterson, W. J.↗