Search NASA⌕ Search

SEARCH · Search NASA

Results for “variable order”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Electrocatalytic Hydrogen Production by a Nickel Complex Containing a Tetradentate Phosphine Ligand

A nickel complex has been synthesized that contains the P4N2 ligand, a tetradendate phosphine ligand with two pendant amines in the ligand backbone. The rigidly square planar Ni(P4N2)2+ complex is an active electrocatalyst for reduction of protons to hydrogen. Using N,N-dimethylformamidium as the acid in wet acetonitrile solution, Ni(P4N2)2+ displays a turnover frequency of 1.6 × 106 s–1, which is among the fastest rates reported for any molecular electrocatalyst. This high catalytic rate comes at the cost of a 1200 mV overpotential at the catalytic half wave potential. The Ni(II) state of the catalyst was found to be stable under strongly acidic conditions, with only trace decomposition observed over two weeks in the presence of 0.1 M trifluoromethanesulfonic acid. The catalyst was less stable in the Ni(0) state due to the inability of the rigid P4N2 ligand to adopt a tetrahedral geometry. Using variable scan rate cyclic voltammetry, a first order rate constant of ~1 s–1 was measured for dissociation of a phosphine from Ni(0), which is proposed to be a key step for determining the lifetime of the catalyst during electrolysis. This research was supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the U.S. Department of Energy (DOE), Office of Science, Office of Basic Energy Sciences. Pacific Northwest National Laboratory is operated by Battelle for DOE.

Klug, Christina↗
DOE OSTI2018

Standardized protocols and procedures can precisely and accurately quantify non-structural carbohydrates

Non-structural carbohydrates (NSCs), the stored products of photosynthesis, building blocks for growth, and fuel for respiration, are central to plant metabolism, but their measurement is challenging. Differences in methods and procedures among laboratories can cause results to vary widely, limiting our ability to integrate and generalize patterns in plant C balance among studies. A recent assessment found that NSC concentrations measured for a common set of samples can vary by an order of magnitude, but sources for this variability were unclear. We measured a common set of nine plant material types, and two synthetic samples with known NSC concentrations, using a common protocol for sugar extraction and starch digestion, and three different sugar quantification methods (ion chromatography, enzyme, acid) in six laboratories. We also tested how sample handling, extraction solvent, and centralizing parts of the procedure in one laboratory affected results. NSC concentrations measured for synthetic samples were within about 11.5% of known values for all three methods. However, differences among quantification methods were the largest source of variation in NSC measurements for natural plant samples because the three methods quantify different NSCs. The enzyme method quantified only glucose, fructose, and sucrose, with ion chromatography we additionally quantified galactose, while the acid method quantified a large range of mono- and oligosaccharides. For some natural samples, acid method quantification doubled sugar relative to the other methods, demonstrating that trees allocate C to a range of sugar molecules. Sample handling had little effect on measurements, while ethanol sugar extraction improved accuracy over water extraction. Our results demonstrate that reasonable accuracy of NSC measurements can be achieved when different methods are used, as long as protocols are robust and standardized. Thus, we provide detailed protocols for the extraction, digestion and quantification of NSCs in plant samples, which should improve the comparability of NSC measurements among laboratories.

Landhäusser, Simon M.↗
DOE OSTI2024

Chemomechanics in alloy phase stability

We describe a first-principles statistical mechanics method to calculate the free energies of crystalline alloys that depend on temperature, composition, and strain. The approach relies on an extension of the alloy cluster expansion to include an explicit dependence on homogeneous strain in addition to site occupation variables that track the degree of chemical ordering. The method is applied to the Si-Ge binary alloy and is used to calculate free energies that describe phase stability under arbitrary epitaxial constraints. We find that while the incoherent phase diagram (in which coexisting phases are not affected by coherency constraints) hosts a miscibility gap, coherent phase equilibrium predicts ordering and negative enthalpies of mixing. Instead of chemical instability, the chemomechanical free energy exhibits instabilities along directions that couple the composition of the alloy with a volumetric strain order parameter. Furthermore, this has fundamental implications for phase field models of spinodal decomposition as it indicates the importance of gradient energy coefficients that couple gradients in composition with gradients in strain.

Materials Science↗
DOE OSTI2019

Separations of Variables and Analytic Contractions on Two-Dimensional Hyperboloids

In this review we present recent results in the field of analytical contraction of Lie algebra in two-dimensional hyperbolic space. A complete geometric description for all possible orthogonal and nonorthogonal (related to the first order symmetries) systems of coordinates, which allow separation of variables of two-dimensional Laplace–Beltrami or Helmholtz equation on the two-sheeted (upper sheet) H{sub 2} and the one-sheeted H-tilde {sub 2} hyperboloids is given. The limiting transition between non subgroup (mostly parametric) and subgroup systems is conducted. The analytic contractions between various systems of coordinates in two hyperbolic spaces and Euclidean E{sub 2} and Minkowski E{sub 1,1} spaces are presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Spatial and Temporal Variability of Vertical Velocity under Shallow Cumulus

Vertical velocity distribution below cloud is one of the key determinants of cloud life cycle, but observations of this variable are extremely sparse in space. Doppler lidar retrievals and large-eddy simulations at the U.S. Department of Energy’s Atmospheric Radiation Measurement User Facility Southern Great Plains site are used to determine whether vertical velocity statistics from temporally dense profiles at a single location can be substituted for spatial vertical velocity statistics. We show that even a small number (five) of widely distributed [ O (1°) latitude/longitude spacing] lidars is sufficient sampling to reconstruct domainwide spatial vertical velocity variance, but not higher moments of the vertical velocity distribution. Spatial and temporal vertical velocity variances in the Doppler lidar observations are nearly interchangeable as long as the spatial variance is temporally averaged and the temporal variance is averaged across lidars. This is true even though the dominant spatial scales of vertical velocity variability are ≲ 3 km, more than an order of magnitude smaller than the spacing between the lidars. Further, in the limit where the temporal variance does not vary across a spatial domain (e.g., if the meteorological and surface forcing of the atmospheric turbulence is homogeneous across the domain) and the domain-mean vertical velocity is zero, the commonly available retrieval of temporal vertical velocity variance at one site is equivalent to the spatial variance over the domain. We use an updraft parcel model to show that substituting temporal for spatial vertical velocity statistics will have a relatively minor effect on cloud droplet number concentrations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Development of a dynamical model and energy analysis for wheel loader

The objective of this paper is to develop a fully integrated model for the wheel loader, including the subsystem dynamics of the engine, drivetrain, working circuit, steering circuit, and vehicle. It leads to a high-order strongly nonlinear system, and all state variables are coupled together to form a Multi-Input and Multi-Output (MIMO) system. A control architecture is proposed to decouple the MIMO system into several Single-Input and Single-Output (SISO) systems. Here, a tracking problem has been formulated to validate this fully integrated model with the field test data. The accuracy of the model is verified by the 2.3% difference between the measured and simulated fuel consumption. Meanwhile, an energy distribution analysis is conducted to reveal the energy consumption and energy loss of each portion of the wheel loader. Such a model can be used to plan the working pattern, guide the driving habits of human operators, or refine the underlying architecture, leading to the ultimate goal of reducing total fuel consumption and improving productivity.

42 ENGINEERING↗
DOE OSTI2019

Robust, automated sleep scoring by a compact neural network with distributional shift correction

Studying the biology of sleep requires the accurate assessment of the state of experimental subjects, and manual analysis of relevant data is a major bottleneck. Recently, deep learning applied to electroencephalogram and electromyogram data has shown great promise as a sleep scoring method, approaching the limits of inter-rater reliability. As with any machine learning algorithm, the inputs to a sleep scoring classifier are typically standardized in order to remove distributional shift caused by variability in the signal collection process. However, in scientific data, experimental manipulations introduce variability that should not be removed. For example, in sleep scoring, the fraction of time spent in each arousal state can vary between control and experimental subjects. We introduce a standardization method, mixture z-scoring, that preserves this crucial form of distributional shift. Using both a simulated experiment and mouse in vivo data, we demonstrate that a common standardization method used by state-of-the-art sleep scoring algorithms introduces systematic bias, but that mixture z-scoring does not. We present a free, open-source user interface that uses a compact neural network and mixture z-scoring to allow for rapid sleep scoring with accuracy that compares well to contemporary methods. This work provides a set of computational tools for the robust automation of sleep scoring.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Modifications to Solar Titan-130 Combustion Systems for Efficient, High Turndown Operation

The project team of Southwest Research Institute® (SwRI®), Solar Turbines Incorporated (Solar), the Electric Power Research Institute (EPRI), the University of California, Irvine (UCI), and the Georgia Institute of Technology (Georgia Tech) investigated methods to allow higher efficiency part-load operation of a Solar Titan 130 gas turbine. The objective was to develop a low-emission combustion system capable of sustaining combustion and avoiding lean blowout during high turndown operation, which would allow the gas turbine to operate as efficiently as possible at part load. Currently, electric utility markets are beginning to experience substantial increases in renewable energy generation. Some of these renewable energy sources have highly variable output in an uncontrolled manner. In order to maintain grid stability, there is a need for power plants to ramp up power to the grid rapidly to make up for drops in renewable generation. This is often termed spinning reserve, but the size of this reserve may need to increase as renewable penetration into the electric utility market increases. Small combined heat and power (CHP) power plants provide a promising option for meeting this spinning reserve requirement. In order to operate in spinning reserve while still meeting the heat requirements for the CHP, the gas turbine needs to operate efficiently at very low loads. Efficient, high turndown operations in this engine are limited by the lean flammability limit of the premixed combustion system. This project sought enhance the lean operability range of the Titan 130 combustor. First, the project team participated in a brainstorming activity and ultimately selected two concepts to explore: fuel augmentation with hydrogen (H2) to improve the stability at lean operating conditions and modifications to the fuel nozzle to improve the emissions performance at lean operating conditions. Analytical and laboratory investigations were accomplished by UCI to investigate the efficacy of H2 addition at improving lean blow out (LBO) limits and the resulting emissions. These investigations used a variety of chemical reactor network (CRN) and CFD models, validated against laboratory data, to model the impact of H 2 and inform the experimental efforts accomplished by SwRI and Solar. Ultimately, both the CRN and CFD models yielded generally good agreement with the experimental data below a particular temperature threshold. Atmospheric tests of a full-scale T130 annular combustor were performed at SwRI facilities in San Antonio, Texas, to investigate the use of H 2 addition. For these tests, the T130 combustion system remained largely unchanged; minor modifications were performed to the fuel ducting to allow for the safe use of H 2 . The test ultimately demonstrated that the addition of H 2 to the fuel mixture significantly increased the AFR ratio at which the combustor could operate. This improvement to the LBO limit should allow for less use of compressor bleed and less throttling needed by the inlet guide vanes (IGV). This in turn could result in more efficient operation of the gas turbine at lower load points. The second modification explored in this work was a direct modification to the T130 injector. The project team hypothesized that modifications to the pilot of the T130 injector could provide lower emissions at high turn-down operations. These modifications were manufactured and explored by the team at Solar. High pressure rig tests, originally slated to occur at SwRI, were ultimately accomplished by Solar to maintain overall project budget and mitigate cost growth attributable to supply chain issues and inflation. The pressurized rig tests ultimately showed that the SwRI Project No. 18.24153 - DE-EE0008415 Page 2 Final Technical Report January 24, 2024 modifications did not significantly alter the performance of the combustion system at the high turn-down conditions; both the modified injectors and the baseline configuration exhibited elevated emissions comparted to the full-load operating condition. A final set of studies performed by EPRI investigated the benefit-cost of flexible CHP as well as a grid interconnection study for the California Independent System Operator (CAISO) grid. These studies considered: traditional CHP with no spinning reserve available for on-demand grid support, 50% flexible CHP where 50% of the machine’s capacity is consumed by on-site baseload operations while providing an additional 50% capacity for on-demand grid support, and 70% flexible CHP where 70% of capacity is consumed on-site by baseload operations and 30% is available for on-demand grid support. In all cases, the analyses showed a benefit-to-cost ratio greater than unity implying a positive net present value for all configurations. However, the traditional CHP showed the most economic benefit. These results are sensitive to several factors, many of which are not fully known and may vary over time. Thus site owners must be convinced that taking up the increased costs and risks from flexible CHP would be worth implementing. As the grid in California and across the country transition to incorporate larger renewable energy generation, flexible CHP can provide much needed operating reserves and dispatchability. Alternative fuel options, such as hydrogen blending and biofuels, may also lower carbon intensities of CHP. Flexible CHP should be examined in the evolving market to understand innovative business models, changes market rules and services, and new technologies.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2019

Updates on Nucleon Form Factors from Clover-on-HISQ Lattice Formulation

Updates on results for the electric, magnetic and axial vector form factors are presented. The data analyzed cover high statistics measurements on 11 ensembles generated with 2+1+1 flavors of HISQ fermions by the MILC collaboration. The data cover the range 0.05 fm < a < 0.15 fm in lattice spacing, 135 MeV < M π < 320 MeV in the pion mass and 3.3 < M π L < 5.5 in the lattice size. Fits to control excited-state contamination use up to 3-states in the spectral decomposition of the 3-point functions. The simultaneous chiral-continuum-finite-volume fits include leading order corrections in each of the three variables.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Virtual element approximations of the time-fractional nonlinear convection-diffusion equation on polygonal meshes

We extend the Virtual Element Method to a two-dimensional unsteady nonlinear convection-diffusion equation characterized by a fractional-order derivative with respect to the time variable. Our methodology is based on three fundamental technical components: a fractional version of the Grunwald-Letnikov approximation, discrete maximal regularity, and the regularity theory associated with non-linearity. We prove the method's well-posedness, i.e., the approximate solution's existence and uniqueness to the time-fractional convection-diffusion equation with a Lipschitz nonlinear source term. The fully discrete scheme inherently maintains stability and consistency by leveraging the discrete maximal regularity and the energy projection operator. The convergence in the L 2 -norm and H 1 -norm to various mesh configurations is validated by numerical results, underlining the practical effectiveness of the proposed method.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1967

A conceptual, parallel operating data compression processor

Data compressor processor concept envisions a simplified system for telemetry communications. It is simultaneously a zero-order processor and a floating aperture, a variable aperture, and a binary integer aperture with a decoded buffet fullness counter.

Anderson, T. O.↗
NASA NTRS1972

Analytic partial derivatives for estimating low-thrust parameters.

Analytic partial derivatives for estimating orbital low-thrust parameters via differential correction are developed and compared with two different numerical methods. The formulation is independent of the particular thrust model used and is applicable to all physically possible elliptic orbits. The starting point for the development is the set of variational equations of the elliptic orbital elements in the form due to Lagrange. The first time derivatives of the elements are transformed to derivatives with respect to the space variable, true anomaly, and integrated to first order in closed form in a straightforward general perturbations approach, with one exception: particular attention is given to the mean anomaly as influenced by thrust perturbations in the semimajor axis so that the complete first-order effect is included. The partials of the elements are then taken with respect to any given thrust parameter. Two comparisons are made with numerical methods for computing these thrust partials: numerical quotients and numerical integration of the variational equations for thrust.

Cunningham, G. W.↗
NASA NTRS1973

Detection of fatigue cracks by nondestructive testing methods

The effectiveness was assessed of various NDT methods to detect small tight cracks by randomly introducing fatigue cracks into aluminum sheets. The study included optimizing NDT methods calibrating NDT equipment with fatigue cracked standards, and evaluating a number of cracked specimens by the optimized NDT methods. The evaluations were conducted by highly trained personnel, provided with detailed procedures, in order to minimize the effects of human variability. These personnel performed the NDT on the test specimens without knowledge of the flaw locations and reported on the flaws detected. The performance of these tests was measured by comparing the flaws detected against the flaws present. The principal NDT methods utilized were radiographic, ultrasonic, penetrant, and eddy current. Holographic interferometry, acoustic emission monitoring, and replication methods were also applied on a reduced number of specimens. Generally, the best performance was shown by eddy current, ultrasonic, penetrant and holographic tests. Etching provided no measurable improvement, while proof loading improved flaw detectability. Data are shown that quantify the performances of the NDT methods applied.

Anderson, R. T.↗
NASA NTRS1973

A variation of the Davis-Smith method for in-flight determination of spacecraft magnetic fields.

A variation of a procedure developed by Davis and Smith (1968) is presented for the in-flight determination of spacecraft magnetic fields. Both methods take statistical advantage of the observation that fluctuations in the interplanetary magnetic field over short periods of time are primarily changes in direction rather than in magnitude. During typical solar wind conditions between 0.8 and 1.0 AU, a statistical analysis of 2-3 days of continuous interplanetary field measurements yields an estimate of a constant spacecraft field with an uncertainty of plus or minus 0.25 gamma in the direction radial to the sun and plus or minus 15 gammas in the directions transverse to the radial. The method is also of use in estimating variable spacecraft fields with gradients of the order of 0.1 gamma/day and less and in other special circumstances.

Belcher, J. W.↗
NASA NTRS1973

Asymptotic solution to the tangential low thrust energy increase trajectory

A approximate analytic solution to the low thrust constant acceleration energy increase trajectory using a tangential steering program is presented. The solution is based on a two-variable asymptotic expansion of the equations of motion formulated in regularized variables. The high accuracy of the second order solution derived is demonstrated by comparing it with numerically integrated trajectories.

Schwenzfeger, K. J.↗
NASA NTRS1978

A note on the averaging method

A simple problem of a two-body system perturbed by the disturbing function epsilon/r-squared is considered to show that the time-averaged equations of the true and mean anomaly are not necessarily equal. Secular effects due to perturbations in the mean and true anomalies are different not only in value but also in sign. A more general case where the disturbing function is periodic with respect to the mean anomaly is also considered. Here a discrepancy in the time-averaged solutions is due to the fact that the mean anomaly is an action-angle variable conjugate to the action variable L, while the true anomaly is not. When the action-angle variables are chosen as dependent variables, the Hamiltonian is a function only of action variables. One must first derive first-order solutions, substitute them into the right-hand side of the equations of motion, and then take time averages.

Kinoshita, H.↗