Search NASA⌕ Search

SEARCH · Search NASA

Results for “ADHESIVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Interfacial adhesion: Theory and experiment

Adhesion, the binding of different materials at an interface, is of general interest to many branches of technology, e.g., microelectronics, tribology, manufacturing, construction, etc. However, there is a lack of fundamental understanding of such diverse interfaces. In addition, experimental techniques generally have practical objectives, such as the achievement of sufficient strength to sustain mechanical or thermal effects and/or have the proper electronic properties. In addition, the theoretical description of binding at interfaces is quite limited, and a proper data base for such theoretical analysis does not exist. This presentation will review both experimental and theoretical aspects of adhesion in nonpolymer materials. The objective will be to delineate the critical parameters needed, governing adhesion testing along with an outline of testing objectives. A distinction will be made between practical and fundamental objectives. Examples are given where interfacial bonding may govern experimental consideration. The present status of theory is presented along wiith recommendations for future progress and needs.

Ferrante, John↗

Initial adhesive screening of novel polyamide-imides and their copolymers

Continued interest by the research community in thermally stable, tough, high temperature adhesives has resulted in the investigation by Langley Research Center of two linear aromatic polyamide-imide (PAI) homopolymers and two linear aromatic PAI copolymers. The homopolymers were made with either 3,3'=DABA or 4,4'-DABA and BTDA. The two polymers were prepared with a monomer ratio of 0.75 DABP:0.25 DABA:1.00 BTDA. These aromatic PAIs possess high thermal stability because of intermolecular hydrogen bonding and chain stiffness. Lap shear strength (LSS) was the main criteria used to evaluate the polymers as adhesives. LSS of bonded Ti-6Al-4V was determined at room temperature (RT), 177, 204 and 232 C. The glass transition temperature and the type of bond failure were also determined. The best LSS values of the four adhesive systems investigated were obtained with the PAI copolymer identified in the report as LARC-TPI (25 percent 3,3'-DABA); however, it did not produce LSSs nearly as high as LARC-TPI. The poor flow properties observed appear to be due to a combination of high molecular weight and the increased interchain electronic interactions associated with the amide group.

Donald J Progar↗

Reducing adhesion and agglomeration within a cloud of combustible particles

The study of combustible particle clouds inside flame tubes is of fundamental scientific interest as well as a practical concern. Only the suspended concentration is important to the combustion process, so that assurances must be provided that a minimum of particles adheres to the tube wall. This paper demonstrates experimentally the ability to minimize adhesion and agglomeration of acoustically-mixed lycopodium particles within a 5-cm diameter lexan flame tube. The area density of particles (ADP) adhering to the wall of bare lexan tubes was measured at greater than 100 particles/sq mm. The nature of adhesion was found to be clearly electrostatic, with the ADP level aggravated by increased mixing time, vigor, and the concentration of particles. Increases in the conductivity of the air and the tube wall did not affect ADP levels substantially. However, the observed adhesion was reduced to less than 10 p/sq mm when the air was ionized by use of an alpha emitter mounted on the inner walls of the flame tube.

Ross, Howard D.↗

Evaluation of polyimide films as adhesives

A commercially available LARC-TPI film and an experimentally prepared film of LARC-TPI with 5 mol pct of 4,4-prime-oxydianiline (ODA), designated as LARC-TPI/ODA, were evaluated as thermoplastic adhesive films for bonding Ti-6Al-4V. Lap shear strength was used to evaluate the materials as adhesives. They were characterized after fracture by determining the glass transition temperature, T(g). The mode of failure is also reported. Thermal exposure at 240 C for 500 and 1000 h and a 72-h water-boil were conducted on lap shear specimens prepared with the two adhesive films. Lap shear tests were conducted at room temperature, 177 C, 204 C, and 232 C before and after exposures.

Progar, Donald J.↗

Effect of adhesive interleaving and discontinuous plies on failure of composite laminates subject to transverse normal loads

Results of a series of tests to determine the effects of adhesive interleaving and discontinuous plies (plies with end-to-end gaps) on the displacements, failure loads and failure modes of graphite-epoxy laminates subjected to transverse normal loads are presented. Adhesive interleaving can be used to contain local damage within a group of plies, i.e., to arrest crack propagation on the interlaminate level, and it can increase the amount of normal displacement the laminate can withstand before failure. However, the addition of adhesive interleaving to a laminate does not significantly increase its load carrying capability. A few discontinuous plies in a laminate can reduce the normal displacement and load at failure by 10 to 40 percent compared to a laminate with no discontinuous plies, but the presence of the ply discontinuities does not generally change the failure location or the failure mode of the laminate.

Jegley, Dawn C.↗

Simplified procedures for designing adhesively bonded composite joints

Procedures for the preliminary design of composite adhesive joints are described. Typical joints, their respective free body diagrams, and approximate equations for estimating the stresses in each of these typical joints are summarized. Equations are also presented to check the critical conditions of the joint such as minimum length, maximum adhesive shear stress, and peel-off stress. To illustrate the procedure, sample designs are described in step-by-step fashion for a butt joint with single doubler subjected to static loads, cyclic loads, and environmental effects. The results show that unsymmetric adhesive joints are inefficient and should be avoided, and hygrothermal environments and cyclic loads dramatically reduce the structural integrity of the joint and require several joint lengths compared with those for static load with no environmental effects.

Chamis, C. C.↗

A comparison of pure mode I and mixed mode I-III cracking of an adhesive containing an open knit cloth carrier

Static and fatigue tests were carried out on two commercial modified epoxy film adhesives with a wide open knit polyester carrier in order to compare crack resistance in mode I and mixed mode I-III loading. The carrier cloth is found to have a significant influence on the cracking behavior of the adhesives. The open air net carrier used in this study separates from the adhesive in mode I cracking but shreds during mixed-mode crack extension. This decreases the opening mode toughness but increases the mixed-mode toughness as compared with results obtained earlier using a heavier knit carrier. The results suggest that the type of carrier may have a far larger influence on crack resistance than is generally recognized.

Ripling, E. J.↗

Interfacial adhesion - Theory and experiment

Adhesion, the binding of different materials at an interface, is of general interest to many branches of technology, e.g., microelectronics, tribology, manufacturing, construction, etc. However, there is a lack of fundamental understanding of such diverse interfaces. In addition, experimental techniques generally have practical objectives, such as the achievement of sufficient strength to sustain mechanical or thermal effects and/or have the proper electronic properties. In addition, the theoretical description of binding at interfaces is quite limited, and a proper data base for such theoretical analysis does not exist. This presentation will review both experimental and theoretical aspects of adhesion in nonpolymer materials. The objective will be to delineate the critical parameters needed, governing adhesion testing along with an outline of testing objectives. A distinction will be made between practical and fundamental objectives. Examples are given where interfacial bonding may govern experimental consideration. The present status of theory is presented along with recommendations for future progress and needs.

Ferrante, John↗

Initial evaluation of novel polyamide-imides and their copolymers as adhesives

Continued interest by the research community in thermally stable, tough, high temperature adhesives has resulted in the investigation by Langley Research Center of two linear aromatic polyamide-imide (PAI) homopolymers and two linear aromatic PAI copolymers. The homopolymers were made with either 3,3'=DABA or 4,4'-DABA and BTDA. The two polymers were prepared with a monomer ratio of 0.75 DABP:0.25 DABA:1.00 BTDA. These aromatic PAIs possess high thermal stability because of intermolecular hydrogen bonding and chain stiffness. Lap shear strength (LSS) was the main criteria used to evaluate the polymers as adhesives. LSS of bonded Ti-6Al-4V was determined at room temperature (RT), 177, 204 and 232 C. The glass transition temperature and the type of bond failure were also determined. The best LSS values of the four adhesive systems investigated were obtained with the PAI copolymer identified in the report as LARC-TPI (25 percent 3,3'-DABA); however, it did not produce LSSs nearly as high as LARC-TPI. The poor flow properties observed appear to be due to a combination of high molecular weight and the increased interchain electronic interactions associated with the amide group.

Progar, Donald J.↗

Instrumented adhesion tests on plasma sprayed thermal barrier coatings

The failure mechanisms of plasma-sprayed two-layer coatings consisting of an NiCrAlY or NiCrAlZr bond coat with an yttria-stabilized zirconia overlay are presently examined by tensile adhesion tests. It has been found that adhesive failure within the bond coat exhibits greater failure strain than the cohesive failure of the ceramic overlay, supporting the view of the intermediate coatings being highly compliant. The absolute extension exhibited by failures occurring only through the ceramic coating is greater than that of adhesive failure, since the ceramic coating is much thicker than the bond coat.

Berndt, Christopher C.↗

Fast-Acting Rubber-To-Coated-Aluminum Adhesive

Cyanoacrylate adhesive used to join rubber to coated aluminum easier to apply and more effective. One-part material applied in single coat to aluminum treated previously with epoxy primer and top coat. Parts mated as soon as adhesive applied; no drying necessary. Sets in 5 minutes. Optionally, accelerator brushed onto aluminum to reduce setting time to 30 seconds. Clamping parts together unnecessary. Adhesive comes in four formulations, all based on ethyl cyanoacrylate with various amounts of ethylene copolymer rubber, poly(methyl methacrylate), silicon dioxide, hydroquinone, and phthalic anhydride.

Comer, Dawn A.↗

The looped adhesive strip: An example of coplanar delamination interaction

The phenomenon of peeling and debonding of thin layers is a subject of interest to those concerned with adhesives, thin films, and layered materials. In recent years much attention has been focused on such problems as a result of increased interest and application of advanced composites and thin film coatings. A related problem which is of interest for its own sake but also represents a simple example of a tangled adhesive strip and of coplanar delamination interaction, is the problem of a looped adhesive strip. This is the subject of the present study. Researchers consider here the problem of an elastic strip which possesses an adherend on (at least) one of its surfaces. If the strip is deformed so that two portions of such a surface are brought into contact, a position of the strip becomes bonded and a loop is formed. Researchers are interested in determining the equilibrium configuration of such a strip and investigating the behavior of the strip when its edges are pulled apart. The problem is approached as a moving interior boundary problem in the calculus of variations with the strip modeled as an inextensible elastica and the bond strength characterized by its surface energy. A Griffith type energy criterion is employed for debonding, and solutions corresponding to the problem of interest obtained. The solution obtained will be seen to predict the interesting phenomenon of bond point propagation, as well as the more standard peeling type behavior. Numerical results demonstrating the phenomena of interest are presented as well and will be seen to reveal both stable and unstable propagation of the boundaries of the bonded portion of the strip, depending upon the loading conditions.

Bottega, W. J.↗

NDE of adhesive bonds and bondlines; Proceedings of the 1989 ASNT Fall Conference, Valley Forge, PA, Oct. 9-13, 1989

The conference presents papers on the Solid Propulsion Integrity Program, the NDE methodology of adhesive bond strength determination, and an interface layer model for ultrasonic inspection of adhesive bonds. Also considered are pulse/echo ultrasonic methods for inspecting bondlines, ultrasonic detection of kissing bonds in adhesive joints, and the NDE needs and requirements for SRM bondline inspection. Thermographic stress analysis of bonded joints is discussed as well as the filmless and real-time applications of holography.

Source record↗

Simplified procedures for designing adhesively bonded composite joints

Procedures for the preliminary design for composite adhesive joints are described. Typical joints, their respective free body diagrams, and approximate equations for estimating the stresses in each of these typical joints are summarized. Equations are also presented to check the critical conditions of the joint such as minimum length, maximum adhesive shear stress, and peel-off stress. To illustrate the procedure, sample designs are described in step-by-step fashion for a butt joint with single doubler subjected to static loads, cyclic loads, and environmental effects. The results show that unsymmetric adhesive joints are inefficient and should be avoided, and hygrothermal environments and cyclic loads dramatically reduce the structural integrity of the joint and require several joint lengths compared with those for static load with no environmental effects.

Chamis, C. C.↗

Fundamental considerations in adhesion, friction and wear for ceramic-metal contacts

Fundamental studies of friction, wear and adhesion of ceramics in contact with metals are evaluated. It is shown that friction and adhesion are strongly dependent on the ductility of the metals. The surface energy, friction, adhesion and hardness of a metal are related to its Young's modulus and shear modulus, which have a marked dependence on the electron configuration of the metal. Generally, the greater the sheer modulus, the less metal transfer there is to the ceramic.

Miyoshi, Kazuhisa↗

Evaluation of Surlyn 8920 as PHE Visor Material and Evaluations of New Adhesives for Improving Bonding Between Teflon and Stainless Steel at Cryogenic Temperature

Two studies are presented, and in the first study, Surlyn 8920 (an ionic and amorphous low density polyethylene made by Dupont) was evaluated as a possible replacement of Plexyglass G as PHE visor material. Four formulations of the polymer were made by adding different amounts of UV stabilizer, energy quencher, and antioxident in a Brabender Plasticorder. The formulated polymers were molded in the form of sheets in a compression molder. Cut samples from the molded sheets were exposed in a weatherometer and tested on Instron Tensile Tester for strength and elongation. Specially molded samples of the formulated polymers were subjected to Charpy Impact Tests. In the second study, preliminary evaluations of adhesives for improvement of bonding between Teflon and stainless steel (SS) were performed. Kapton, a high temperature polyimide made by Dupont, and a rubber based adhesive made by Potter Paint Co., were evaluated against industrial quality epoxy, the current material used to bond Teflon and SS. The degreased surfaces of the SS discs were etched mechanically, with a few of these etched chemically. The surfaces of the SS discs were etched mechanically, with a few of these etched chemically. Bonding strengths were evaluated using lap shear tests on the Instron Tensile Tester for the samples bonded by Kapton and industrial quality epoxy. Bond strengths were also evaluated using a pull test on the Instron for the samples bonded by Potter adhesive (CWL-152) and industrial quality epoxy. Based on limited lap shear data, Kapton gave bond strength favorable compared to that of industrial epoxy. Based on limited pull test data, Kapton bonded and CWL-152 bonded samples showed poor strength compared to epoxy bonded sample.

Ray, Asit K.↗

Adhesive Contact Sweeper

Adhesive contact sweeper removes hair and particles vacuum cleaner leaves behind, without stirring up dust. Also cleans loose rugs. Sweeper holds commercially available spools of inverted adhesive tape. Suitable for use in environments in which air kept free of dust; optics laboratories, computer rooms, and areas inhabited by people allergic to dust. For carpets, best used in tandem with vacuum cleaner; first pass with vacuum cleaner removes coarse particles, and second pass with sweeper extracts fine particles. This practice extends useful life of adhesive spools.

Patterson, Jonathan D.↗

Active adhesion concepts for in-orbit structural construction

The in-orbit assembly of structural elements is presently addressed by means of a continuum-based theory of active-adhesion contact/impact which assumes the manufacturability of active adhesion elements by piezoelectric (and similarly behaving) materials. Block bonding characteristics can furnish an effective alternative to optimal control-based, impact surge force-mitigation strategies, especially in the numerous nonsmooth control problems that are difficult to synthesize and implement. Attention is given to design concepts employing combined serial/parallel-bonded active adhesion elements composed of cascaded piezoelectric devices.

Park, K. C.↗