SEARCH · Search NASA

Results for “Cladding design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

DOE OSTI2017

Study on Neutronics Calculation Method of SCWR with Annular Fuel Assembly

Supercritical Water-Cooled Reactor (SCWR) is one of Gen-IV reactor systems for its advantages over LWRs, such as high thermal efficiency, simplified reactor system and economics. Annular fuel was proposed by MIT to supplant conventional solid fuel and improve power density in LWRs. Annular fuel is cooled from both inside and outside of the fuel. Thus a lower fuel temperature and cladding surface temperature can be achieved with higher power density. SCWRs will benefit from this advantage because high cladding temperature (usually over 650 degree C) is one challenge of SCWRs. Using annular fuel in SCWRs is very promising. This is also because the inner hole of the annual fuel can provide extra neutron moderation. Supercritical water density is too low to provide enough moderation. Different analysis codes have been developed all over the world to carry out SCWR pre-conceptual core design. Yamaji et al. developed SRAC/ASMBURN/COREBN to study Japan version of SCWR. Monti et al. used ERANOS to analyze HPLWR (High Performance Light Water Reactor). WIMS-D4/CITATION was also used to calculate HPLWR by Tashakor et al.. These codes employ a two-step method used in PWRs calculation. Lattice/Assembly calculation is carried out as the first step. In the second step, few group constant of different fuel assembly types is then used in core calculation. MCNP had also been used to study SCWR by Watta et al.. Due to large computation time cost, it's used mostly to analyze fuel assembly or core performance rather than pre-conceptual design, in which much optimization is needed. In this research, a neutronics calculation code for SCWR is developed using two-step method. This code is verified by comparing with Monte-Carlo code. Fuel assembly homogenization method is studied to improve the code accuracy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2016

A Radial Heat Flow Apparatus for Thermal Conductivity Characterisation of Cylindrical Samples

During the last two decades, silicon carbide based ceramic composites (SiC/SiC) have become a candidate material for nuclear fuel cladding, first for advanced nuclear systems, such as the GFR, and recently also as potential replacement material for nuclear fuel cladding in light water reactors. This work is contributing to the General Atomics/Westinghouse led CARAT project. In this frame, the thermal conductivity (TC) of cladding prototype sections are measured both before and after neutron irradiation with the purpose of better understanding the effects of neutron irradiation on the pyrolytic carbon interphase linking the SiC fibres to the SiC matrix. To this end, an apparatus has been designed and built to measure the TC of short cylindrical samples, whose lengths range from 5 to 20 cm, by the radial heat flow method. To avoid oxidation issues, the experiments are carried out in vacuum. Today the most common measurement method used to characterise the TC of materials is the so-called laser-flash technique, whereby a short high intensity laser pulse is shot on one surface of a thin flat sample and the energy transfer through the sample is analysed on the other side. Though much faster and easier to implement than the apparatus presented in this work, laser-flash equipment does have issues when dealing with highly anisotropic materials or capturing shape effects such as those present in large aspect ratio samples such as cladding tube sections. The two aforementioned effects are exactly what the developed equipment has been built to capture. The radial heat flow method is based on the principle of measuring the temperature difference building up through a piece of material as this material acts as a thermal resistance against a known heat flow crossing it. This paper presents a new implementation of one of the classical thermal conductivity measurement techniques. Since the development of the laser-flash method in the sixties, steady-state measurements such as the radial heat flow have fallen in disuse. In this discussion, it is shown that a direct measurement method can be used and even be preferable in the case of highly anisotropic materials such as SiC/SiC composites. The advantage of this experimental setup is that the actual transverse conductivity is obtained, whereas laser-flash measurements yield a response in which both the transverse and axial conductivities are mixed. Further steps of this study will include the measurements of samples irradiated with neutrons in the MITR test-reactor. The aim will be to evidence the role played by the pyrolytic carbon interphase by linking the TC measurements with energy filtered electron microscopy. We would like to acknowledge General Atomics and Westinghouse for their support in the frame of the CARAT research program. Providing us with actual prototype clad sections is a unique opportunity. Furthermore the Swiss CCEM.ch project MeAWaT is acknowledged for partially financing the development of the measurement device. (authors)

36 MATERIALS SCIENCE↗

DOE OSTI2020

Analysis of Using a Hybrid ZIRCEX Process to Generate High-Assay Low-Enriched Uranium (HALEU) - 20158

Idaho National Lab (INL) is investigating the feasibility of providing High-Assay Low Enriched Uranium (HALEU) by recovering Highly Enriched Uranium (HEU) from spent nuclear fuel (SNF) and downblending the HEU with natural, low-enriched, or depleted uranium (NU, LEU, or DU). That investigation identified that significant quantities of HALEU could be produced with a Hybrid ZIRCEX process to further advanced reactor research while reducing INL's environmental liability. Many new advanced reactor designs are being developed with improved safety, efficiency, and economics. Most require nuclear fuel with U-235 enrichment between 5% and 20%, which is defined as HALEU. Although technically feasible, there is no current domestic capability to make HALEU in the US. While it is anticipated that industry will provide HALEU through commercial enrichment once advanced reactors mature, until a market is established, an interim source of HALEU is needed to enable research and demonstration. An interim source of HALEU could be provided by recovering the HEU in some DOE-managed SNF and downblending it to between 5% and 20% using the Hybrid ZIRCEX Process. ZIRCEX is a dry head-end process to remove cladding (zirconium or aluminum) from SNF. Drying of the SNF is needed prior to introduction to ZIRCEX. After cladding removal, uranium and fission products in the bed material are oxidized and elutriated. In a Hybrid ZIRCEX process, the HEU process stream is sent to a very compact, modular solvent extraction process for uranium purification. The uranyl nitrate from solvent extraction is denitrated and calcined to produce a HALEU product ready for fuel fabrication. The long-lived fission products from solvent extraction are immobilized in glass using a small in-can melt. By removing the cladding before dissolution, the volume of glass waste is reduced by a factor of up to 300 times (when compared to not removing the cladding from the fuel). Other radioactive wastes from the process could be disposed of as Class A or Class B low-level waste. In addition to producing HALEU for advanced reactors, consumption of SNF would reduce DoE's environmental liability. Incorporating low-enriched spent fuel (versus exclusive use of LEU, DU, or NU) into the downblending scheme could reduce the SNF inventory even further. Several downblending and enrichment scenarios using INL fuels were investigated in this study. The results of this analysis show that the Hybrid ZIRCEX process could make a significant contribution to needed HALEU feedstock and reduce the environmental liability of managing SNF at INL. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Low-loss low thermo-optic coefficient Ta 2 O 5 on crystal quartz planar optical waveguides

Optical resonator-based frequency stabilization plays a critical role in ultra-low linewidth laser emission and precision sensing, atom clocks, and quantum applications. However, there has been limited success in translating traditional bench-top stabilization cavities to compact on-chip integrated waveguide structures that are compatible with photonic integration. The challenge lies in realizing waveguides that not only deliver low optical loss but also exhibit a low thermo-optic coefficient and frequency noise stability. Given the problematic sources of frequency noise within dielectrics, such as thermorefractive noise, resonators with small thermo-optic response are desirable for on-chip reference cavities. We report the first demonstration of a Ta 2 O 5 (tantala) waveguide core fabricated on a crystal quartz substrate lower cladding with TEOS-PECVD SiO 2 upper cladding. This waveguide offers significant advantages over other waveguides in terms of its low thermo-optic coefficient and reduced thermorefractive-related frequency noise. We describe the waveguide structure and key design parameters as well as fabrication considerations for processing tantala on quartz waveguides. We report a waveguide thermo-optic coefficient of -1.14 × 10 -6 RIU/K, a value that is over 6 times smaller in magnitude than that of SiO 2 -substrate tantala waveguides, with a propagation loss of 1.19 dB/cm at 1550 nm and <1.33 dB/cm across the 1525 nm–1610 nm wavelength range. Within a 1.6 mm radius ring resonator, we demonstrate a 2.54 × 10 5 intrinsic Q factor. With the potential for very low loss and the ability to control the thermal response, this waveguide platform takes a key step toward creating thermally stable integrated resonators for on-chip laser frequency stabilization and other applications.

42 ENGINEERING↗

DOE OSTI2012

GTL-1 Irradiation Summary Report

The primary objective of the Gas Test Loop (GTL-1) miniplate experiment is to confirm acceptable performance of high-density (i.e., 4.8 g-U/cm3) U3Si2/Al dispersion fuel plates clad in Al-6061 and irradiated under the relatively aggressive Booster Fast Flux Loop (BFFL) booster fuel conditions, namely a peak plate surface heat flux of 450 W/cm2. As secondary objectives, several design and fabrication variations were included in the test matrix that may have the potential to improve the high-heat flux, high-temperature performance of the base fuel plate design.1, 2 The following report summarizes the life of the GTL-1 experiment through end of irradiation, including as-run neutronic analysis, thermal analysis and hydraulic testing results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Preliminary Evaluation of Loading DOE Standard Canisters in the INL CPP-603 Irradiated Fuel Storage Facility - 20543

This paper looks at the equipment and operations necessary to load United States Department of Energy (DOE)-owned Spent Nuclear Fuel (SNF) into DOE Standard Canisters in the CPP-603 Irradiated Fuel Storage Facility (IFSF) in the Idaho Nuclear Technology and Engineering Center (INTEC) area at Idaho National Laboratory (INL). Two types of fuels are looked at in this evaluation: Advanced Test Reactor (ATR) fuel (uranium-aluminide fuel with aluminum cladding) and Peach Bottom fuel (thorium-uranium carbide fuel in a graphite matrix). The fuel ready for loading would come from fuel storage canisters in the CPP-603 facility. The paper describes the facility, the fuel types, the DOE Standard Canisters, and existing equipment; lists the needed loading operations; reviews facility features and equipment to perform the operations; and then lists the decisions, analyses, designs, demonstrations, and modifications that will be needed to perform the loading of DOE-owned SNF into DOE Standard Canisters in the CPP-603 IFSF. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2021

Test Plan for Investigation of Hydrogen Generation in SNF Canisters

This report presents a test plan to investigate radiolytic hydrogen generation in spent nuclear fuel (SNF) canisters containing Zr-based cladding materials. The initial primary contributor to the generation of radiolytic hydrogen is estimated to be the residual physisorbed water on the ZrO 2 film, post-dry out. Over the longer term the primary hydrogen source is associated with the aluminum hydroxides and water vapor. The proposed testing to be conducted in FY22 would consist of lab-scale testing on non-radioactive surrogates of oxidized ZIRLO tubing and unalloyed zirconium using a miniature steel canister (“mini-canister") designed to allow intermittent, in-situ sampling of the canister gas during irradiation. The mini-canister approach for irradiation with in-situ monitoring system was used in a recent and on-going study [McNamara and Verst, 2020a & 2020b; Verst et al., 2021] to measure radiolytic hydrogen generation from aluminum SNF cladding surrogate materials. This proposed testing will form part of the overall materials performance evaluation of the commercial SNF-in-canister system and is part of the technical bases for their continued safe dry storage

08 HYDROGEN↗

DOE OSTI2013

Reversible Bending Fatigue Test System for Investigating Vibration Integrity of Spent Nuclear Fuel during Transportation

Transportation packages for spent nuclear fuel (SNF) must meet safety requirements under normal and accident conditions as specified by federal regulations. During transportation, SNF experiences unique conditions and challenges to cladding integrity due to the vibrational and impact loading during road or rail shipment. Oak Ridge National Laboratory (ORNL) has been developing testing capabilities that can be used to improve the understanding of the impacts on SNF integrity due to vibration loading, especially for high burn-up SNF in normal transportation operation conditions. This information can be used to meet the nuclear industry and U.S. Nuclear Regulatory Commission needs in the area of safety and security of spent nuclear fuel storage and transport operations. The ORNL developed test system can perform reversible-bending fatigue testing to evaluate both the static and dynamic mechanical response of SNF rods under simulated loads. The testing apparatus is also designed to meet the challenges of hot-cell operation, including remote installation and detachment of the SNF test specimen, in-situ test specimen deformation measurement, and implementation of a driving system suitable for use in a hot cell. The system contains a U-frame set-up equipped with uniquely designed grip rigs, to protect SNF rod and to ensure valid test results, and use of 3 specially designed LVDTs to obtain the in-situ curvature measurement. A variety of surrogate test rods have been used to develop and calibrate the test system as well as in performing a series of systematic cyclic fatigue tests. The surrogate rods include stainless steel (SS) cladding, SS cladding with cast epoxy, and SS cladding with alumina pellets inserts simulating fuel pellets. Testing to date has shown that the interface bonding between the SS cladding and the alumina pellets has a significant impact on the bending response of the test rods as well as their fatigue strength. The failure behaviors observed from tested surrogate rods provides a fundamental understanding of the underlying failure mechanisms of the SNF surrogate rod under vibration which has not been achieved previously. The newly developed device is scheduled to be installed in the hot-cell in summer 2013 to test high burnup SNF.

high burn-up spent fuel↗

DOE OSTI2019

Advanced Concepts for Dry Storage Cask Thermal-Hydraulic Testing

The purpose of this report is to review technical issues relevant to the performance evaluation of dry storage systems during vacuum drying and long-term storage operations. It also provides updates on experimental components under development that are vital for pursuing advanced studies. Validation of the extent of water removal in a multi-assembly dry storage system using an industrial vacuum drying procedure is needed, as operational conditions leading to incomplete drying may have potential impacts on the fuel, cladding, and other components in the system. Water remaining in canisters/casks upon completion of vacuum drying can lead to cladding corrosion, embrittlement, and breaching, as well as fuel degradation. Therefore, additional information is needed to evaluate the potential impacts of water retention on extended long-term dry storage. A general lack of data and experience modeling the drying process necessitates the testing of advanced concepts focused on the simulation of industrial vacuum drying. Smaller-scale tests that incorporate relevant physics and well-controlled boundary conditions are necessary to provide insight and guidance to the modeling of prototypic systems undergoing drying processes. This report describes the development and testing of waterproof, electrically-heated spent fuel rod simulators as a proof of concept to enable experimental simulation of the entire dewatering and drying process. This report also describes the preliminary development of specially-designed, unheated mock fuel rods for monitoring internal rod pressures and studying water removal from simulated failed fuel rods. A variety of moisture monitoring instrumentation is also being considered and will be downselected for the tracking of dewpoints of gas samples. The effects of cladding oxidation and crud on water retention in dry storage systems can be explored via separate effects tests (SETs) that would measure chemisorbed and physisorbed water content on cladding samples. The concepts listed above will be incorporated into an advanced dry cask simulator with multiple fuel assemblies in order to account for important inter-assembly heat-transfer physics. Plans are described for harvesting up to five full-length 5x5 laterally truncated assemblies from commercial 17x17 PWR skeleton components with the goal of constructing this simulator.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2015

Quantum photonics hybrid integration platform

Fundamental to integrated photonic quantum computing is an on-chip method for routing and modulating quantum light emission. We demonstrate a hybrid integration platform consisting of arbitrarily designed waveguide circuits and single-photon sources. InAs quantum dots (QD) embedded in GaAs are bonded to a SiON waveguide chip such that the QD emission is coupled to the waveguide mode. The waveguides are SiON core embedded in a SiO{sub 2} cladding. A tuneable Mach Zehnder interferometer (MZI) modulates the emission between two output ports and can act as a path-encoded qubit preparation device. The single-photon nature of the emission was verified using the on-chip MZI as a beamsplitter in a Hanbury Brown and Twiss measurement.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2021

Sockeye: A One-Dimensional, Two-Phase, Compressible Flow Heat Pipe Application

Sockeye is a heat pipe analysis application based on the Multiphysics Object-Oriented Simulation Environment (MOOSE) finite element framework. The primary purpose of Sockeye is to provide a transient heat pipe simulation tool to be used in the analysis of nuclear microreactor designs. Sockeye provides the capability to perform one-dimensional, two-phase, compressible flow simulation of a heat pipe working fluid and two-dimensional, axisymmetric heat conduction for the heat pipe cladding and its surroundings. Sockeye is demonstrated against analytical solutions and experimental data from the SAFE-30 heat pipe module test.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2015

Partially-reflected water-moderated square-piteched U(6.90)O 2 fuel rod lattices with 0.67 fuel to water volume ratio (0.800 CM Pitch)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Pitch Variation Experiments in Water-Moderated Square-Pitched U(6.9)O 2 Fuel Rod Lattices with Fuel to Water Volume Ratios Spanning 0.08 to 0.67

The US Department of Energy (DOE) Nuclear Energy Research Initiative funded the design and construction of the Seven Percent Critical Experiment (7uPCX) at Sandia National Laboratories. The start-up of the experiment facility and the execution of the experiments described here were funded by the DOE Nuclear Criticality Safety Program. The 7uPCX is designed to investigate critical systems with fuel for light water reactors in the enrichment range above 5% 235 U. The 7uPCX assembly is a water-moderated and -reflected array of aluminum-clad square-pitched U(6.90%)O 2 fuel rods. Other critical experiments performed in the 7uPCX assembly are documented in LEU-COMP-THERM-078, LEU-COMP-THERM-080, LEU-COMPTHERM- 096, LEU-COMP-THERM-097, and LEU-COMP-THERM-101. The twenty-seven critical experiments in this series were performed in 2020 in the SCX at the Sandia Pulsed Reactor Facility. The experiments are grouped by fuel rod pitch. Case 1 is a base case with a pitch of 0.8001 cm and no water holes in the array. Cases 2 through 6 have the same pitch as Case 1 but contain various configurations with water holes, providing slight variations in the fuel-to-water ratio. Similarly, Case 7 is a base case with a pitch of 0.854964 cm and no water holes in the array. Cases 8 through 11 have the same pitch as Case 7 but contain various configurations with water holes. Cases 12 through 15 have a pitch of 1.131512 cm and differ according to the number of water holes in the array, with Case 12 having no water holes. Cases 16 through 19 have a pitch of 1.209102 cm and differ according to number of water holes in the array, with Case 16 having no water holes. Cases 20 through 23 have a pitch of 1.6002 cm and differ according to number of water holes in the array, with Case 20 having no water holes. Cases 24 through 27 have a pitch of 1.709928 cm and differ according to number of water holes in the array, with Case 24 having no water holes. As the experiment case number increases, the fuel-to-water volume ratio decreases.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2019

Component Concepts for Advanced Dry Storage Investigations

The purpose of this report is to review technical issues and previous studies relevant to the performance evaluation of dry storage systems during vacuum drying and long-term storage operations and to describe vital experimental components under development that are required for conducting advanced studies. There is a need to validate the extent of water removal in a multi-assembly system using an industrial vacuum-drying procedure, as operational conditions leading to incomplete drying may have potential impacts on the fuel, cladding, and other components in the system. Waterproof, electrically-heated spent fuel rod simulators are under development to enable experimental simulation of the entire de-watering and drying process. Specially-designed, unheated mock fuel rods are used to monitor internal rod pressures and study water removal from simulated failed fuel rods. Furthermore, single assembly studies conducted previously cannot incorporate important inter-assembly heat-transfer physics, so plans for harvesting up to five full-length 5 x 5 truncated assemblies from a single 17 x 17 PWR skeleton are described.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Partially-Reflected Water-Moderated Square-Pitched U(6.90)O 2 Fuel Rod Lattices with 0.52 Fuel to Water Volume Ratio (0.855 CM Pitch)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Development of mechanistic, microstructure-informed BISON models for fission product-induced failure mechanisms in advanced nuclear fuels

The US continues to prioritize commercial deployment of advanced reactors—particularly those utilizing U-Zr metallic and TRISO particle fuels. Fission product-induced failure mechanisms for these systems include fuel–cladding chemical interaction in metallic fuel rods, which threatens cladding integrity, and Pd penetration in TRISO particles, which degrades SiC layer properties. Empirical models can be applied within the bounds of existing irradiation databases, but their utility is limited when considering new designs or investigating fundamental material behaviors. The Nuclear Energy Advanced Modeling and Simulation Program is therefore developing mechanistic models for these behaviors, which are expected to aid in fuel design, assist in development of failure mitigation strategies, and provide support for qualification and licensing. These efforts leverage multiscale capabilities to capture the microstructural features and processes that govern these behaviors. This talk summarizes past and ongoing efforts to develop and validate these models for the BISON fuel performance code.

FCCI↗

DOE OSTI2016

Thermal Hydraulics Safety Analyses of TRIGA Reactor Upon Fuel Reconfiguration

Safety analyses of the Training, Research, Isotope, General Atomics (TRIGA) reactor at Kansas State University(KSU) is performed using thermal hydraulic simulations based on changes to reactivity or the volumetric heat generation rate due to changes in the positioning of the enriched fuel elements in the reactor core. If the reactivity or neutronics parameters are known, then they can be used to simulate the thermal energy state of the material which is crucial to assess the safety of the nuclear fuel inside a nuclear reactor. Several thermal hydraulics models and codes have been developed in the past to assess reactor safety. RELAP (Reactor Excursion and Leak Analysis Program) is one such tool widely used throughout the world for safety analyses. Although RELAP is considered a reliable tool by regulators, vendors, and operators, it lacks the numerical fidelity provided by 3-D computational fluid dynamics (CFD) models. This work involves the critical task of assessing safety of a research reactor upon fuel reconfiguration based on models developed in RELAP and comparing them with a commercially available 3-D CFD program. The TRIGA Mark-II reactor, designed by General Atomics and located at Kansas State University, is a class of small pool type inherently safe research reactor licensed to operate at steady state power of up to 1.25 MW. It has a cylindrical core measuring 0.45 meters diametrically and 0.38 meters axially positioned in a tank measuring 1.98 meters diametrically and 6.25 meters axially. It has uranium zirconium hydride (UZrH) fuel rods housed in stainless steel cladding material arranged in five concentric rings (B,C,D,E and F rings, in that order, moving outwards from the center). TRIGA fuel is nominally 20% enriched, but the reactivity of the fuel can be changed by using burnable poisons (not used at KSU), or by varying the total weight percent of uranium in the UZrH fuel meat. The TRIGA reactor is designed to be an inherently safe reactor and is designed to be cooled by natural convection. Thus it is of paramount importance to avoid the film boiling regime; failing to do so will subject the fuel to severe conditions, possibly resulting in its failure due to fuel/clad interactions. A high DNBR ratio is a primary consideration in the reactor core design and thus any modification in the core should ensure that this criteria is always met. In order to fully utilize the capabilities of KSU TRIGA reactor facility, it should be operated at its full capacity, i.e. 1.25 MW, which requires increasing the fuel loading in some of the E- and F-ring elements from 8.5% U (nominal) to 12.0% U (nominal). Only four elements are to be switched to 12% loading, causing local power peaking in these elements. The degree of power peaking to be expected in these 12%-loaded fuel elements was calculated based on a detailed MCNP (Monte Carlo N-Particle code) model of the reactor core. Some preliminary results of the calculations are presented in this paper based on changes in peaking factors and power levels. To predict reactor thermal behavior, axial changes in the peaking factors obtained from MCNP models were used to calculate volumetric energy density functions for a single channel one dimensional RELAP model and a three dimensional COMSOL model of the TRIGA MARK-II reactor. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2014

Reversal bending fatigue test system for investigating vibration integrity of spent nuclear fuel during transportation

Transportation packages for spent nuclear fuel (SNF) must meet safety requirements under normal and accident conditions as specified by federal regulations. During transportation, SNF experiences unique conditions and challenges to cladding integrity due to the vibrational and impact loading during road or rail shipment. Oak Ridge National Laboratory (ORNL) has been developing testing capabilities that can be used to improve the understanding of the impacts on SNF integrity due to vibration loading, especially for high burn-up SNF in normal transportation operation conditions. This information can be used to meet the nuclear industry and U.S.Nuclear Regulatory Commission needs in the area of safety and security of SNF storage and transportation operations. The ORNL developed test system can perform reversal bending fatigue testing to evaluate both the static and dynamic mechanical response of SNF rods under simulated loads. The testing apparatus is also designed to meet the challenges of hot cell operation, including remote installation and detachment of the SNF test specimen, in situ test specimen deformation measurement, and implementation of a driving system suitable for use in a hot cell. The system contains a U frame set-up equipped with uniquely designed grip rigs to protect the SNF rod sample and to ensure valid test results, and uses three specially designed linear variable differential transformers to obtain the in situ curvature measurement. A variety of surrogate test rods have been used to develop and calibrate the test system as well as in performing a series of systematic cyclic fatigue tests. The surrogate rods include stainless steel (SS) cladding, SS cladding with cast epoxy and SS cladding with alumina pellet inserts simulating fuel pellets. Testing to date has shown that the interface bonding between the SS cladding and the alumina pellets has a significant impact on the bending response of the test rods as well as their fatigue strength. The failure behaviours observed from tested surrogate rods provide a fundamental understanding of the underlying failure mechanisms of the SNF surrogate rod under vibration,which has not been achieved previously. The newly developed device is scheduled to be installed in the hot cell in summer 2013 to test high burn-up SNF.

high burn up fuel↗