Search NASA⌕ Search

SEARCH · Search NASA

Results for “Complex structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Spatiotemporal Variability and Propagation of Equatorial Noise Observed by Cluster

We report a multipoint case study of the electromagnetic equatorial noise observed by the Cluster project. High-resolution data were measured in three close points in space located in the morning sector of the outer plasmasphere. We demonstrate a narrow latitudinal extent of the emissions with a typical width of 2 degrees, centered near the minimum-B equator. Power spectra recorded by the different satellites show a complex structure of emission lines whose relative intensities and positions vary at timescales of 1-2 min and/or at spatial scales of tens of wavelengths. These lines do not match harmonics of the local proton cyclotron frequency, as it would be expected if the waves are generated by energetic ions and observed near the source region. We bring observational evidence that the waves propagate with a significant radial component and thus can propagate from a distant generation region located at different radial distances where ion cyclotron frequencies match the observed fine structure.

Santolik, O.↗
NASA NTRS2003

Application of Probability Methods to Assess Crash Modeling Uncertainty

Full-scale aircraft crash simulations performed with nonlinear, transient dynamic, finite element codes can incorporate structural complexities such as: geometrically accurate models; human occupant models; and advanced material models to include nonlinear stress-strain behaviors, and material failure. Validation of these crash simulations is difficult due to a lack of sufficient information to adequately determine the uncertainty in the experimental data and the appropriateness of modeling assumptions. This paper evaluates probabilistic approaches to quantify the effects of finite element modeling assumptions on the predicted responses. The vertical drop test of a Fokker F28 fuselage section will be the focus of this paper. The results of a probabilistic analysis using finite element simulations will be compared with experimental data.

Lyle, Karen H.↗
NASA NTRS2003

Plasma membrane disruption: repair, prevention, adaptation

Many metazoan cells inhabit mechanically stressful environments and, consequently, their plasma membranes are frequently disrupted. Survival requires that the cell rapidly repair or reseal the disruption. Rapid resealing is an active and complex structural modification that employs endomembrane as its primary building block, and cytoskeletal and membrane fusion proteins as its catalysts. Endomembrane is delivered to the damaged plasma membrane through exocytosis, a ubiquitous Ca2+-triggered response to disruption. Tissue and cell level architecture prevent disruptions from occurring, either by shielding cells from damaging levels of force, or, when this is not possible, by promoting safe force transmission through the plasma membrane via protein-based cables and linkages. Prevention of disruption also can be a dynamic cell or tissue level adaptation triggered when a damaging level of mechanical stress is imposed. Disease results from failure of either the preventive or resealing mechanisms.

NASA Discipline Cell Biology↗
NASA NTRS2004

Chemistry, Adhesive and Composite Properties of Low Molecular Weight Phenylethynyl Terminated Oligomers

PETI-5 (1250 and 2500 g/mole) were prepared and characterized. Neat resin, adhesive and composite properties were determined and compared with those of PETI-5 (5000 g/mole). Relative to PETI-5 (5000 g/mole), PETI-5 (2500 g/mole) exhibited improved processability and equivalency in the adhesive and composite properties measured thus far. This resin, in both adhesive film and prepreg form, has the potential to offer significant improvements in the processing of complex structural composite parts.

Connell, John W.↗
NASA NTRS2001

Comparison of Modal Analysis Methods Applied to a Vibro-Acoustic Test Article

Modal testing of a vibro-acoustic test article referred to as the Aluminum Testbed Cylinder (ATC) has provided frequency response data for the development of validated numerical models of complex structures for interior noise prediction and control. The ATC is an all aluminum, ring and stringer stiffened cylinder, 12 feet in length and 4 feet in diameter. The cylinder was designed to represent typical aircraft construction. Modal tests were conducted for several different configurations of the cylinder assembly under ambient and pressurized conditions. The purpose of this paper is to present results from dynamic testing of different ATC configurations using two modal analysis software methods: Eigensystem Realization Algorithm (ERA) and MTS IDEAS Polyreference method. The paper compares results from the two analysis methods as well as the results from various test configurations. The effects of pressurization on the modal characteristics are discussed.

Pritchard, Jocelyn↗
NASA NTRS1996

Applications of Advanced, Waveform Based AE Techniques for Testing Composite Materials

Advanced, waveform based acoustic emission (AE) techniques have been previously used to evaluate damage progression in laboratory tests of composite coupons. In these tests, broad band, high fidelity acoustic sensors were used to detect signals which were then digitized and stored for analysis. Analysis techniques were based on plate mode wave propagation characteristics. This approach, more recently referred to as Modal AE, provides an enhanced capability to discriminate and eliminate noise signals from those generated by damage mechanisms. This technique also allows much more precise source location than conventional, threshold crossing arrival time determination techniques. To apply Modal AE concepts to the interpretation of AE on larger composite structures, the effects of wave propagation over larger distances and through structural complexities must be well characterized and understood. In this research, measurements were made of the attenuation of the extensional and flexural plate mode components of broad band simulated AE signals in large composite panels. As these materials have applications in a cryogenic environment, the effects of cryogenic insulation on the attenuation of plate mode AE signals were also documented.

Prosser, William H.↗
NASA NTRS1996

Advanced AE Techniques in Composite Materials Research

Advanced, waveform based acoustic emission (AE) techniques have been successfully used to evaluate damage mechanisms in laboratory testing of composite coupons. An example is presented in which the initiation of transverse matrix cracking was monitored. In these tests, broad band, high fidelity acoustic sensors were used to detect signals which were then digitized and stored for analysis. Analysis techniques were based on plate mode wave propagation characteristics. This approach, more recently referred to as Modal AE, provides an enhanced capability to discriminate and eliminate noise signals from those generated by damage mechanisms. This technique also allows much more precise source location than conventional, threshold crossing arrival time determination techniques. To apply Modal AE concepts to the interpretation of AE on larger composite specimens or structures, the effects of modal wave propagation over larger distances and through structural complexities must be well characterized and understood. To demonstrate these effects, measurements of the far field, peak amplitude attenuation of the extensional and flexural plate mode components of broad band simulated AE signals in large composite panels are discussed. These measurements demonstrated that the flexural mode attenuation is dominated by dispersion effects. Thus, it is significantly affected by the thickness of the composite plate. Furthermore, the flexural mode attenuation can be significantly larger than that of the extensional mode even though its peak amplitude consists of much lower frequency components.

Prosser, William H.↗
NASA NTRS1991

Evolutionary dynamics of plants and animals: a comparative approach

Patterns of longevity and rate of appearance of taxa in the fossil record indicate a different evolutionary dynamic between land plants and marine invertebrates. Among marine invertebrates, rates of taxonomic turnover declined through the Phanerozoic, with increasingly extinction-resistant, long-lived, clades coming to dominate. Among terrestrial vascular plants, rates of turnover increased through the Phanerozoic, with short-lived, extinction-prone clades coming to dominate from the Devonian to the present. Terrestrial vertebrates appear to approximate the marine invertebrate pattern more closely than the plant record. We identify two features which individually or jointly may have influenced this distinction. First, land plants continuously invaded stressful environments during their evolution, while marine invertebrates and terrestrial vertebrates did not. Second, the relative structural simplicity and indeterminate mode of plant growth vs. the relative structural complexity and determinate mode of animal growth may have influenced the timing of major clade origin in the two groups.

Review↗
NASA NTRS2002

Three-Dimensional Postbuckling Analysis of Curved Beams

Presented here is a method of solving highly flexible curved beam undergoing huge static or quasi-static deformations. A geometrically exact beam theory based on the use of Jaumann stresses and strains and exact coordinate transformation is presented in terms of 17 first-order ordinary differential equations, and a multiple shooting method is used to solve the corresponding nonlinear two-point boundary value problems. The geometrically exact beam theory accounts far large rotations, large displacements, initial curvatures, extensionality, and transverse shear strains. Four examples are used to demonstrate this method, including a rotating clamped-free beam under the influence of gravity and centrifugal forces, an L-frame subjected to an in-plane tip load, a circular arch subjected to a concentrated load, and a clamped-hinged helical spring subjected to an axial displacement. Results show that the combination of the multiple shooting method and the geometrically exact beam theory works very well. Moreover, the obtained numerically exact solutions can be used to verify the accuracy of nonlinear finite element codes for nonlinear analysis of complex structures.

Pai, P. Frank↗
NASA NTRS1997

Tensegrity: the architectural basis of cellular mechanotransduction

Physical forces of gravity, hemodynamic stresses, and movement play a critical role in tissue development. Yet, little is known about how cells convert these mechanical signals into a chemical response. This review attempts to place the potential molecular mediators of mechanotransduction (e.g. stretch-sensitive ion channels, signaling molecules, cytoskeleton, integrins) within the context of the structural complexity of living cells. The model presented relies on recent experimental findings, which suggests that cells use tensegrity architecture for their organization. Tensegrity predicts that cells are hard-wired to respond immediately to mechanical stresses transmitted over cell surface receptors that physically couple the cytoskeleton to extracellular matrix (e.g. integrins) or to other cells (cadherins, selectins, CAMs). Many signal transducing molecules that are activated by cell binding to growth factors and extracellular matrix associate with cytoskeletal scaffolds within focal adhesion complexes. Mechanical signals, therefore, may be integrated with other environmental signals and transduced into a biochemical response through force-dependent changes in scaffold geometry or molecular mechanics. Tensegrity also provides a mechanism to focus mechanical energy on molecular transducers and to orchestrate and tune the cellular response.

Review↗
NASA NTRS2005

Iron K Features in the Quasar E 1821+643: Evidence for Gravitationally Redshifted Absorption?

We report a Chandra high-energy grating detection of a narrow, redshifted absorption line superimposed on the red wing of a broad Fe K line in the z = 0.297 quasar E 1821+643. The absorption line is detected at a confidence level, estimated by two different methods, in the range approx. 2 - 3 sigma. Although the detection significance is not high enough to exclude a non-astrophysical origin, accounting for the absorption feature when modeling the X-ray spectrum implies that the Fe-K emission line is broad, and consistent with an origin in a relativistic accretion disk. Ignoring the apparent absorption feature leads to the conclusion that the Fe-K emission line is narrower, and also affects the inferred peak energy of the line (and hence the inferred ionization state of Fe). If the absorption line (at approx. 6.2 keV in the quasar frame) is real, we argue that it could be due to gravitationally redshifted Fe XXV or Fe XXVI resonance absorption within approx. 10 - 20 gravitational radii of the putative central black hole. The absorption line is not detected in earlier ASCA and Chandra low-energy grating observations, but the absorption line is not unequivocally ruled out by these data. The Chandra high-energy grating Fe-K emission line is consistent with an origin predominantly in Fe I-XVII or so. In an ASCA observation eight years earlier, the Fe-K line peaked at approx. 6.6 keV, closer to the energies of He-like Fe triplet lines. Further, in a Chandra low-energy grating observation the Fe-K line profile was double-peaked, one peak corresponding to Fe I-XVII or so, the other peak to Fe XXVI Ly alpha. Such a wide range in ionization state of Fe is not ruled out by the HEG and ASCA data either, and is suggestive of a complex structure for the line-emitter.

Yaqoob, Tahir↗
NASA NTRS2003

Bio-Organic Nanotechnology: Using Proteins and Synthetic Polymers for Nanoscale Devices

While the ability of proteins to self-assemble makes them powerful tools in nanotechnology, in biological systems protein-based structures ultimately depend on the context in which they form. We combine the self-assembling properties of synthetic diblock copolymers and proteins to construct intricately ordered, three-dimensional polymer protein structures with the ultimate goal of forming nano-scale devices. This hybrid approach takes advantage of the capabilities of organic polymer chemistry to build ordered structures and the capabilities of genetic engineering to create proteins that are selective for inorganic or organic substrates. Here, microphase-separated block copolymers coupled with genetically engineered heat shock proteins are used to produce nano-scale patterning that maximizes the potential for both increased structural complexity and integrity.

Molnar, Linda K.↗
NASA NTRS2005

Metallographic Cooling Rate of IVA Irons Revisited

There is long standing problem reconciling the chemical evidence that the IVA iron meteorites formed in a core with the diverse cooling rates reported by several researchers. This large inferred range of cooling rates suggests that the IVA irons were distributed at different depths in a parent body with a complex structure when the Widmanstatten pattern formed. On the other hand, some researchers argued that the diverse cooling rates in group IVA result from inaccurate model parameters such as phase diagram, interdiffusion coefficients, and kamacite nucleation and growth mechanisms. In addition, the measured cooling rates may not apply for the same cooling temperature ranges, and the variation in the crystallographic orientations of the Widmanstatten plates on the analysis surface may result in inaccurate measurements of widths needed for the computer simulation models. We have revaluated the major parameters in computer model developed by Hopfe and Goldstein and measured cooling rates for the IVA irons. Such data are useful in evaluating whether these meteorites were part of a single core of a parent body during the formation of the Widmanstatten pattern.

Yang, J.↗
NASA NTRS2006

Overview of High-Resolution Nondestructive Inspection of the Space Shuttle External Tank (ET) Spray-on-Foam Insulation (SOFI) and Acreage Heat tiles using Focused, Synthetic and Holographical Millimeter Wave Techniques

Space Shuttle Columbia's catastrophic failure has been attributed to a piece of spray-on-foam insulation (SOFI) that was dislodged from the external tank (ET) and struck the leading edge of the left wing. A piece of SOFI was also dislodged in the recent Space Shuttle Discovery's flight. From immediately after the Columbia accident, microwave and millimeter wave nondestructive testing methods were considered as potential effective inspection tools for evaluating the integrity of the SOFI. To this end and as a result of these efforts, both real-focused, synthetic focusing and holographical techniques, at a wide range of frequencies covering 24 GHz to 150 GHz, have been developed for this purpose. Images of various complex SOFI panels with a wide range of embedded anomalies (representing real potential defects) have been produced using these techniques, including relatively small anomalies located near complex structural features representative of the external tank. These real-focused and 3D holographical images have effectively demonstrated the utility of these methods for SOFI inspection as being viable, robust, repeatable, simple, portable and relatively inexpensive (tens of $K as opposed to hundreds of $K). In addition, the potential viability of these methods for inspecting acreage heat tiles have has been demonstrated. This paper presents an overview of these activities, representative images of these panels using all of the imaging techniques used and a discussion of the practical attributes of these inspection methods.

Kharkovsky, S.↗
NASA NTRS1993

Mapping the Piute Mountains, CA with Thermal Infrared Multispectral Scanner (TIMS)

Thermal Infrared Multispectral Scanner (TIMS) data were acquired in 1990 over the PiuteMountains, California to evaluate their usefulness for lithologic mapping in an area ofmetamorphosed, structurally complex, igneous and sedimentary rocks. The data were calibrated,atmospherically corrected, and emissivity variations extracted from them. There was an excellentvisual correlation between the units revealed in the TIMS data and the recent mapping in the easternside of the area. It was also possible to correct, improve and extend the recent map. For example,several areas of amphibolite were identified in the TIMS data that had been incorrectly mapped asgranodioritic gneiss, and the presence of a swarm of mafic dikes, of which only a few had previouslybeen identified, was revealed...

Hook, S. J.↗
NASA NTRS2006

Applying Parallel Adaptive Methods with GeoFEST/PYRAMID to Simulate Earth Surface Crustal Dynamics

This viewgraph presentation reviews the use Adaptive Mesh Refinement (AMR) in simulating the Crustal Dynamics of Earth's Surface. AMR simultaneously improves solution quality, time to solution, and computer memory requirements when compared to generating/running on a globally fine mesh. The use of AMR in simulating the dynamics of the Earth's Surface is spurred by future proposed NASA missions, such as InSAR for Earth surface deformation and other measurements. These missions will require support for large-scale adaptive numerical methods using AMR to model observations. AMR was chosen because it has been successful in computation fluid dynamics for predictive simulation of complex flows around complex structures.

GeoFEST↗
NASA NTRS2006

Effect of Composite Substrates on the Mechanical Behavior of Brazed Joints in Metal-Composite System

Advanced composite components are being considered for a wide variety of demanding applications in aerospace, space exploration, and ground based systems. A number of these applications require robust integration technologies to join dissimilar materials (metalcomposites) into complex structural components. In this study, three types of composites (C-C, C-SiC, and SiC-SiC) were vacuum brazed to commercially pure Ti using the active metal braze alloy Cusil-ABA (63Ag-35.3Cu-1.75Ti). Composite substrates with as fabricated and polished surfaces were used for brazing. The microstructure and composition of the joint, examined using scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS), showed sound metallurgical bonding in all systems. The butt strap tensile (BST) test was performed on bonded specimens at room and elevated temperatures. Effect of substrate composition, interlaminar properties, and surface roughness on the mechanical properties and failure behavior of joints will be discussed.

Singh, M.↗
NASA NTRS1978

Comsat Antenna

The antenna shown is the new, multiple-beam, Unattended Earth Terminal, located at COMSAT Laboratories in Clarksburg, Maryland. Seemingly simple, it is actually a complex structure capable of maintaining contact with several satellites simultaneously (conventional Earth station antennas communicate with only one satellite at a time). In developing the antenna, COMSAT Laboratories used NASTRAN, NASA's structural analysis computer program, together with BANDIT, a companion program. The computer programs were used to model several structural configurations and determine the most suitable, The speed and accuracy of the computerized design analysis afforded appreciable savings in time and money.

Source record↗