Search NASA⌕ Search

SEARCH · Search NASA

Results for “Drying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Droplet-Surface Impingement Dynamics for Intelligent Spray Design

Spray cooling has high potential in thermal management and life support systems by overcoming the deleterious effect of microgravity upon two-phase heat transfer. In particular spray cooling offers several advantages in heat flux removal that include the following: 1) By maintaining a wetted surface, spray droplets impinge upon a thin fluid film rather than a dry solid surface; 2. Most heat transfer surfaces will not be smooth but rough. Roughness can enhance conductive cooling, aid liquid removal by flow channeling; and 3. Spray momentum can be used to a) substitute for gravity delivering fluid to the surface, b) prevent local dryout and potential thermal runaway and c) facilitate liquid and vapor removal. Yet high momentum results in high We and Re numbers characterizing the individual spray droplets. Beyond an impingement threshold, droplets splash rather than spread. Heat flux declines and spray cooling efficiency can markedly decrease. Accordingly we are investigating droplet impingement upon a) dry solid surfaces, b) fluid films, c) rough surfaces and determining splashing thresholds and relationships for both dry surfaces and those covered by fluid films. We are presently developing engineering correlations delineating the boundary between splashing and non-splashing regions. Determining the splash/non-splash boundary is important for many practical applications. Coating and cooling processes would each benefit from near-term empirical relations and subsequent models. Such demonstrations can guide theoretical development by providing definitive testing of its predictive capabilities. Thus, empirical relations describing the boundary between splash and non-splash are given for drops impinging upon a dry solid surface and upon a thin fluid film covering a similar surface. Analytical simplification of the power laws describing the boundary between the splash and non-splash regions yields insight into the engineering parameters governing the splash and non-splash outcomes of the fluid droplets. The power law correlation is shown separating the splashing versus non-splashing regions as developed for droplets impinging upon a dry solid surface. Splashing upon a dry surface is reasonably described by Ca greater than 0.85, reflecting the competing roles of surface tension and viscosity. The power law correlation is shown separating the splashing versus non-splashing regions as developed for droplets impinging upon a thin fluid film covering the solid surface. Splashing upon a thin fluid film, as described by v (pd/s) greater than 63, is governed by fluid density and surface tension, but is rather independent of viscosity. Finally, the data presented here suggests that a more direct dependence upon the surface tension and viscosity, given a better understanding of their interplay, would allow accurate description of the droplet-surface impacts for more complicated situations involving non-Newtonian fluids, specifically those exhibiting viscoelastic behavior.

Wal, Randy L. Vander↗
NASA NTRS2009

Improving Our Understanding of Atlantic Hurricanes Through Knowledge of the Saharan Air Layer: Hope Or Hype?

The existence of the Saharan air layer (SAL), a layer of warm, dry, dusty air frequently present over the tropical Atlantic Ocean, has long been appreciated. The nature of its impact on hurricanes remains unclear, with some researchers arguing that the SAL amplifies hurricane development and with others arguing that it inhibits it. The potential negative impacts of the SAL include 1) low-level vertical wind shear associated with the African easterly jet; 2) warm air aloft, which increases thermodynamic stability; and 3) dry air, which produces cold downdrafts. Some investigators have assumed the validity of these proposed negative influences and have frequently used them to explain the failure of individual storms to intensify or to explain the relative inactivity of recent hurricane seasons. Multiple NASA satellite data sets and National Centers for Environmental Prediction global analyses are used to characterize the SAL's properties and evolution in relation to developing hurricanes. The results will shows that neither jet--induced vertical wind shear nor warm SAL air (high stability) produce significant negative impacts on Atlantic storms. Dry air appears to be a key mechanism for SAL influence, but the presence of dry SAL air is not always a good indicator of whether a storm will weaken since many examples of intensifying storms surrounded by such dry air can be found. Idealized simulations will be used to evaluate the role of dry air. Finally, two case studies of supposedly "prime examples" of SAL influence will show that the negative influences of the SAL are perhaps too readily ascribed to individual storms that fail to reach their maximum potential intensity.

Braun, Scott↗
NASA NTRS2007

Fabrication of Polyimide-Matrix/Carbon and Boron-Fiber Tape

The term HYCARB denotes a hybrid composite of polyimide matrices reinforced with carbon and boron fibers. HYCARB and an improved process for fabricating dry HYCARB tapes have been invented in a continuing effort to develop lightweight, strong composite materials for aerospace vehicles. Like other composite tapes in this line of development, HYCARB tapes are intended to be used to build up laminated structures having possibly complex shapes by means of automated tow placement (ATP) - a process in which a computer-controlled multiaxis machine lays down prepreg tape or tows. The special significance of the present process for making dry HYCARB for ATP is that it contributes to the reduction of the overall cost of manufacturing boron-reinforced composite-material structures while making it possible to realize increased compression strengths. The present process for making HYCARB tapes incorporates a "wet to dry" process developed previously at Langley Research Center. In the "wet to dry" process, a flattened bundle of carbon fiber tows, pulled along a continuous production line between pairs of rollers, is impregnated with a solution of a poly(amide acid) in N-methyl-2-pyrrolidinone (NMP), then most of the NMP is removed by evaporation in hot air. In the present case, the polyamide acid is, more specifically, that of LaRC. IAX (or equivalent) thermoplastic polyimide, and the fibers are, more specifically, Manganite IM7 (or equivalent) polyacrylonitrile- based carbon filaments that have a diameter of 5.2 m and are supplied in 12,000-filament tows. The present process stands in contrast to a prior process in which HYCARB tape was made by pressing boron fibers into the face of a wet carbon-fiber/ poly(amide acid) prepreg tape . that is, a prepreg tape from which the NMP solvent had not been removed. In the present process, one or more layer(s) of side-by-side boron fibers are pressed between dry prepreg tapes that have been prepared by the aforementioned gwet to dry h process. The multilayer tape is then heated to imidize the matrix material and remove most of the remaining solvent, and is pressed to consolidate the multiple layers into a dense tape. For tests, specimens of HYCARB tapes and laminated composite panels made from HYCARB tape were prepared as follows: HYCARB tapes were fabricated as described above. Each panel was made by laying down ten layers of tape, containing, variously, one, two, or three boron-fiber plies and the remainder carbon- fiber-only plies (see figure). Each panel was made by laying down ten layers of tape. Each panel was then cured by heating to a temperature of 225 C for 15 minutes, then pressing at 200 psi (A1.4 MPa) while heating to 371 C, holding at 371 C for 1 hour, then continuing to hold pressure during cooling. Control specimens that were otherwise identical except that they did not contain boron fibers also were prepared. In room-temperature flexural tests, the HYCARB specimens performed comparably to the control specimens; in room-temperature, open-hole compression tests, the HYCARB specimens performed slightly better, by amounts that increased with boron content.

Belvin, Harry L.↗
NASA NTRSDate not supplied

An Ensemble Investigation of the Causes for Regional Air-Quality Model Critical Load Exceedances Prediction Variability in European and North American Domains Using Diagnostics From Phase 4 of the Air Quality Model Evaluation International Initiative

We summarize tentative findings from multi air quality model ensembles for the years 2009 and 2010 in Europe (EU), and 2010 and 2016 in North America (NA), under AQMEII-4. The model predictions of sulphur and nitrogen deposition were used to estimate exceedances of critical loads for acidification and eutrophication, to show the extent to which the ensemble members agree in the magnitude and the trend of ecologically meaningful impacts. Model exceedance variability was analyzed using AQMEII-4 diagnostics. Evaluation against concentration and wet deposition observations, coupled with these diagnostics, identified specific process representations as the causes for variability between model predictions and for reduced model performance. All models predicted reductions in ecosystem acidification impacts in North America between the years 2010 and 2016, in accord with SO2 emissions reduction legislation which started in 2010 (SO2 SIP) However, all models in EU and NA domains had net negative biases for wet deposition of sulphur and nitrogen relative to observations. The wet S deposition average mean bias for the NA ensemble was -0.17 eq ha-1 d-1, and for the EU ensemble -1.15 eq ha-1 d-1. The NA daily wet deposition average mean bias for NH4+ was -0.37 eq ha-1d-1; EU -1.19 eq ha-1 d-1. The daily NA wet NO3- deposition average mean bias was -0.24 eq ha-1d-1; EU -0.69 eq ha-1 d-1. The members of the ensemble diverged (factor of 10) in their North American predictions for Ndep and consequently their eutrophication exceedances. The models with the highest eutrophication predictions also predicted the highest levels of gas-phase ammonia dry deposition (standard deviation of ammonia dry deposition flux across ensemble members was larger than the ensemble average). These models also had negative biases of predicted ammonia concentrations; average mean biases of -0.63 (satellite NH3) and -0.85 ppbv (surface NH3) compared to ensemble averages of -0.30 and -0.34 ppbv. Diagnostics showed that these differences resulted from the manner in which bidirectional ammonia fluxes were parameterized within these models. The second largest source of NA eutrophication prediction variability were models with positive biases in particulate ammonium and nitrate concentrations, and higher particle nitrogen deposition levels ( particle ammonium concentration bias +0.35 ug m-3; ensemble bias +0.15 ug m-3). We believe two factors may have led to these latter overestimates: higher levels of fine mode particle nitrate formation compared to other models (due to the use of an inorganic heterogeneous chemistry algorithm which did not take base cation chemistry into account), and updates to particle dry deposition velocities carried out in the absence of concurrent updates to wet scavenging algorithms. The relative importance of dry gas, dry particulate, and wet deposition towards total sulphur and nitrogen deposition totals differed between EU and North American domains, though all models had negative biases in wet deposition as noted above. Parallel and subsequent work suggests that multiphase hydrometeor scavenging may improve model wet deposition performance. An increased research focus is recommended for four model processes: multiphase hydrometeor scavenging, ammonia bidirectional fluxes, base cation chemistry and emissions, and particle dry deposition.

regional air-quality model↗
DOE OSTI2025

Impact of processing humidity on ionomer film structure and performance in hydroxide exchange membrane electrolyzers

Hydroxide exchange membrane electrolyzers (HEMELs) enable hydrogen production using low-cost, earth-abundant materials. Improving electrode fabrication is integral to enhancing device performance, and ionomer-responsible for transporting hydroxide and mechanically supporting the catalyst-is a major component. Here, we use experiments and computation to study the effects of relative humidity (RH) during the drying process of poly(aryl piperidinium) ionomer films on HEMEL electrodes. Broadly, the drying environments determine the physical structure and electrochemical traits of the ionomer network. High RH drying yields a highly porous network with excessive water uptake, structural defects, washout, and 64% reduction in hydroxide conductivity. Extremely low RH drying produces an overly compact pore network that hinders hydroxide mobility. In contrast, moderately low RH drying (9% RH) creates an ionomer film with well-balanced traits: excellent mechanical stability and connectivity needed for catalyst retention and hydroxide transport, which improves HEMEL performance by 40% at 1.8 V compared to suboptimal RHs. This research advances HEMEL manufacturing by providing a simple, scalable, and low-cost approach to optimize electrode ionomer films.

36 MATERIALS SCIENCE↗
NASA NTRS2015

Mars: Periglacial Morphology and Implications for Future Landing Sites

At the Mars Phoenix landing site and in much of the Martian northern plains, there is ice-cemented ground beneath a layer of dry permafrost. Unlike most permafrost on Earth, though, this ice is not liquid at any time of year. However, in past epochs at higher obliquity the surface conditions during summer may have resulted in warmer conditions and possible melting. This situation indicates that the ice-cemented ground in the north polar plains is likely to be a candidate for the most recently habitable place on Mars as near-surface ice likely provided adequate water activity approximately 5 Myr ago. The high elevation Dry Valleys of Antarctica provide the best analog on Earth of Martian ground ice. These locations are the only places on Earth where ice-cemented ground is found beneath dry permafrost. The Dry Valleys are a hyper-arid polar desert environment and in locations above 1500 m elevation, such as University Valley, air temperatures do not exceed 0 C. Thus, similarly to Mars, liquid water is largely absent here and instead the hydrologic cycle is dominated by frozen ice and vapor phase processes such as sublimation. These conditions make the high elevation Dry Valleys a key Mars analog location where periglacial processes and geomorphic features can be studied in situ. This talk will focus on studies of University Valley as a Mars analog for periglacial morphology and ice stability. We will review a landing site selection study encompassing this information gleaned from the Antarctic terrestrial analog studies plus Mars spacecraft data analysis to identify candidate landing sites for a future mission to search for life on Mars.

Martian ground ice↗
DOE OSTI2024

High-Efficiency Thermoelectric Clothes Dryer (CRADA Final Report)

A typical clothes dryer in the US accounts for 7% of the average residential customer’s electric bill. Nationwide, consumers pay about $\$$9 billion annually for clothes drying. While energy efficiency for most household appliances has improved by a factor of 2 or more in recent decades, today’s clothes dryers perform similarly to units from the 1970s. Dryer efficiency is measured by the combined energy factor (CEF), with today’s units typically drying 3.73 lb of cloth per kWh consumed. An ENERGY STAR qualified unit must achieve 3.93 lb/kWh (for standard size electric units) and dry in less than 80 minutes. ORNL and CRADA partner Samsung Electronics America have developed an efficient prototype clothes dryer that uses thermoelectric heat pumps instead of electric resistance to dry the clothes. The prototype fabricated at ORNL successfully demonstrated in the laboratory a CEF of 6.89 lb/kWh at standard conditions of 75°F and 50% Relative Humidity (RH), exceeding the original project target of 6.0 lb/kWh. Additional trials on the same prototype achieved faster dry time with slightly lower CEF, meeting all requirements for ENERGY STAR product qualification. Deploying dryers with energy factor of 6 nationwide represents a technical potential of 234 TBtu/yr primary energy savings. The modeling and prototype development activities for the thermoelectric clothes dryer under this CRADA are summarized in this final report.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Woody Feedstock 2022 State of Technology Report

The U.S. Department of Energy promotes production of advanced liquid transportation fuels from lignocellulosic biomass by funding fundamental and applied research that advances the state of technology (SOT). As part of its involvement in this mission, Idaho National Laboratory completes an annual SOT report for n th -plant and 1 st -plant woody biomass feedstock logistics. The purpose of the SOT is to provide the status of feedstock supply system technology development for woody biomass to biofuels relative to technical targets and cost goals from specific design cases, based on data and experimental results. Conventional feedstock supply systems need to be modified to meet the demands of conversion pathways, specifically to have the ability to adjust the quality of the raw biomass materials. Advanced systems incorporate innovative methods of material handling, preprocessing and supply chain configuration. In advanced designs, variability of the raw biomass can be reduced to produce feedstocks of a uniform format, moving toward biomass commoditization. Against this backdrop, the 2022 Woody SOT for low-ash woody feedstocks utilizes feedstock fractionation by incorporating technologies that can separate the biomass into its anatomical fractions (wood, bark, needle, and extrinsic ash) to reduce impurities and attempt to maximize the retention of usable fractions that satisfy downstream quality considerations. By using a series of air classification steps, this strategy can reduce the extrinsic ash in forest residues, separate out a majority of the incoming needles (which can be supplied to alternate markets), and maximize the retention of whitewood in the usable fraction. The fractionated forest residues are then mixed with clean-pine chips in a 50-50 blend to prepare the feedstock for the desired conversion pathway. The n th -plant analysis estimated the delivered cost for the feedstock at $\$$69.23/dry ton (2016$\$$) which represents a $\$$6.64/dry ton decrease compared to the cost estimate of the 2021 Woody SOT supply system for low-ash woody feedstocks. The quality requirements in the 2022 Woody SOT were identical to those of the 2021 Woody SOT at = 1.00 wt % ash and = 50.51 wt% carbon. The cost savings derive primarily from reductions in dry matter losses during air classification. The GHG emissions for the n th -plant analysis were estimated at 178.39 kg CO2e/dry ton compared to 178.71 kg CO 2 e/dry ton in the 2021 Woody SOT, a decrease of 0.32 kg CO2e/dry ton. The small change stems from an increase in emissions attributed to preprocessing and slightly larger savings in emissions from transportation. In the 1 st -plant analysis of the 2022 Woody SOT system, the average throughput was estimated to be approximately 2,128 dry tons/day or 96.51% of the name plate capacity. During the simulation the daily throughput ranged from 1,090 dry tons/day to 2,200 dry tons/day, or 49.43% to 99.75% of the daily nameplate capacity. After the year of operation 722,403 tons of processed feedstock were produced in total without regard to quality considerations (99.64% of the annual nameplate capacity). The variability in throughput was primarily caused by equipment failures in the system. Regular failures, downtime caused by routine maintenance per manufacturer guidelines, contributed to a majority 62.50% of failures and 62.60% of downtime. Failures due to wear were the other cause of disruption within the system, impacting the rotary shear and orbital screen and accounting for 37.50% of the failures and 37.40% of the total downtime. Ultimately the system was on stream for 87.84% during the simulation period, which is only 2.16 percentage points below the nth-plant assumption for on-stream time. The production cost of the system averaged $\$$71.66/dry ton. The costs ranged from a minimum of $\$$71.23/dry ton to a maximum of $\$$2,115.30/dry ton. When dry matter losses (disposed low-quality fractions as well as other losses such as in grinders) were considered the costs increased to an average of $\$$75.11/dry ton with a minimum of $\$$74.69/dry ton and a maximum of $\$$2,136.86/dry ton...

09 BIOMASS FUELS↗
DOE OSTI2025

Characterization of Tank 9H Annulus Sample in Support of Residual Material Inventory Determinations

The Savannah River National Laboratory (SRNL) was requested by Savannah River Mission Completion (SRMC) to provide sample preparation and characterization of the Tank 9H annulus sample in support of Residual Material Inventory Determinations. One Tank 9H sample in three vials [HTF-9-25-13, HTF-9-25-14 and HTF-9-25-15], with each vial containing approximately 200 mL of the Tank 9H annulus salt solution, were delivered to the SRNL Shielded Cells for sample preparation and characterizations in February 2025. The density of the “as-received” solution contained in each of the three Tank 9H annulus sample vials were determined followed by a solid-liquid separation on each one using 0.45-micron Nalgene® nylon filter membranes. The resulting filtrates were combined to form the Tank 9H annulus sample with a total volume of about 600 mL. The combined wet solid fractions, about a total of 4.8 grams of salt material, remaining on the filter membranes were air-dried in the Shielded Cells for 72 hours. The total weight of the air-dried solids was 2.1 grams. These air-dried solids were washed with deionized water (DI water) at a phase ratio of 60 mL DI water/gram of solids to recover insoluble solids, if any. No visible or measurable quantity of insoluble solids were recovered after DI water washing of the air-dried solids because the air-dried solids completely dissolved in the DI water. The solid fraction-wash water was not combined with the 600 mL of the filtrate solution, and the resulting solution was not screened or analyzed for radionuclides. Aliquot sample volumes of the undiluted Tank 9H annulus sample were sent to the SRNL analytical services groups for radionuclides, elementals, anions and total mercury analysis by various methods including radiochemical separations/counting methods, inductively coupled plasma-atomic emission spectroscopy (ICP-AES), and Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and special preparations. All sample analyses were performed in triplicate. This report presents the analytical characterization results for the Tank 9H annulus sample. The results are also reported where analytical methods yielded additional analytes, other than those requested by SRMC. In the characterization of the Tank 9H annulus sample, the detection limits for all the analytes, as specified in the Technical Task Request (TTR) and Task Technical and Quality Assurance Plan (TTQAP), were met.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Aerogel with Unparalleled Performance and Cost-Effectiveness for All Insulation Needs (CRADA Final Report)

Westwood Aerogel investigated the reproducible production of an ambiently or electromagnetic spectrum assisted drying of extremely porous aerogel materials. Traditional aerogel processing is limited by low throughput and scalability due to supercritical drying. Westwood Aerogel’s advanced manufacturing process enables commercialization and deployment at scale, making aerogel materials more accessible to a range of industries and applications. We focused on shifting from the lab scale environment to manufacturing prototypes. The initial manufacturing model is based on the float glass process, which is the industry standard for glass window production, and the paper drying process. By incorporating an ambient drying process a continuous line model can be used from start to finish. The project team worked to develop a continuous manufacturing system to scale-up and reduce costs while maintaining the lightweight and insulative properties of aerospace-grade aerogel. While aerogels are extremely insulative, lightweight, and thin materials (making them ideal insulators across application spaces), high costs and stagnant innovation have hampered their wider adoption. Traditional manufacturing of aerogel requires supercritical extraction of pore fluid to obtain highly insulating materials, which is an energy intensive batch process and limits aerogel production output. Westwood Aerogel’s proprietary ambient drying process enables the continuous production of highly insulative aerogel materials without the use of supercritical extraction.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Cellulose Nanofibrils Dewatered with Poly(Lactic Acid) for Improved Bio-Polymer Nanocomposite Processing

Cellulose nanofibrils (CNFs) have theoretically ideal properties for bio-based composite applications; however, the incorporation of these materials into polymers is made challenging by the strong binding of water to CNFs and the irreversible agglomeration of CNFs during drying. Previous methods used “contact dewatering”, wherein the addition of wood flour (WF) to CNFs facilitated the mechanical removal of water from the system via cold pressing, which showed potential in producing dried CNF fibrils attached to wood fibers for biocomposite applications. In this work, the viability of contact dewatering with poly(lactic) acid (PLA) powder for PLA/CNF composites was evaluated. The energy efficiency of dewatering, preservation of nanoscale CNF morphology, and mechanical properties were examined by mixing wet CNFs with pulverized PLA at various loading levels, pressing water out of the system, and compression molding and shear mixing composites for testing. The most impressive results from this dewatering method were the preservation of micron-to-nanoscale fibers with high aspect ratios in PLA-CNF composites; increased strength and modulus of 1.7% and 4.2%, respectively, compared to neat PLA; equivalent or better properties than spray-dried nanocellulose at similar loading levels; and an 11-194x reduction in drying energy compared to spray-drying CNFs.

Chemistry↗
NASA NTRS1972

Mechanisms of deterioration of nutrients phase 1

Experimental methods are studied by which freeze-dried foods of improved quality are produced. Considered are: (1) Factors effecting the loss of butanol from frozen aqueous food solutions during storage; (2) a freeze-drying microscope system for observing solidification processes in organic mixtures and aqueous inorganic salt solutions; (3) browning of high quality freeze-dried foods with minimal organoleptic and nutritional detoriation; (4) retention of PVP-n-propanol in freeze-dried food models; and (5) effects of freezing rate and sucrose immersion on taste and texture of freeze-dried apple slices.

Karel, M.↗
NASA NTRS1976

Mechanisms of deterioration of nutrients

Methods which produce freeze dried foods of improved quality were examined with emphasis on storage stability. Specific topics discussed include: microstructure of freeze dried systems, investigation of structural changes in freeze dried systems, artificial food matrices, osmotic preconcentration to yield improved quality freeze dried fruits, and storage stability of osmotically preconcentrated freeze dried fruits.

Karel, M.↗
NASA NTRS1980

The evaluation of evaporation by infrared thermography: A critical analysis of the measurements on the Crau test site

Evapotranspiration was calculated for both the dry and irrigated zone by four methods which were compared with the energy balance method serving as a reference. Two methods did not involve the surface temperature. They are ETR(n) = R(n), liable to be valid under wet conditions and ET(eq) = (delta/delta + gamma) R(n) i.e, the first term of Penman's equation, adapted to moderately dry conditions. The methods using surface temperature were the combined energy balance aerodynamic approach and a simplified approach proposed by Jackson et al. Tests show the surface temperature methods give relatively satisfactory results both in the dry and wet zone, with a precision of 10% to 15% compared with the reference method. As was to be expected, ET(eq) gave satisfactory results only in the dry zone and ET(Rn) in the irrigated zone. Thermography increased the precision in the estimate of ET relative to the most suitable classical method by 5% to 8% and is equally suitable for both dry and wet conditions. The Jackson method does not require extensive ground measurements and the evaluation of the surface roughness.

Seguin, B.↗
NASA NTRS1983

The water factor in harvest-sprouting of hard red spring wheat

Sprouting in unthreshed, ripe, hard red spring wheat (Triticum aestivum L.) is induced by rain, but sprouting does not necessarily occur because the crop is wetted. The spike and grain water conditions conducive to sprouting were determined in a series of laboratory experiments. Sprouting did not occur in field growing wheat wetted to 110% water concentration until the spike water concentration was reduced to 12% and maintained at this concentration for 2 days before wetting. When cut at growth stage 11.3, Feekes scale, Saratovskaya 20 (USSR) sprouted after 4 days drying, Olaf and Alex between 7 and 15 days drying and Columbus, recognized for its resistance to harvest time sprouting, after more than 15 days drying. Sprouting potential was enhanced after 4 wetting drying cycles in which any wetted interval was too brief to permit sufficient water imbibition to initiate sprouting. At harvest ripeness, grain water concentration exceeded spike water concentration by 0.7 percentage units. Following 6 months storage, 20% of the kernels in 300 spike bundles (simulating windrows) sprouted within 28 hrs after initiation of wetting to saturation (150% water concentration). Ninety percent sprouting occurred within 8 days in bundles maintained at 75% water concentration and higher, but less sprouting occurred in bundles dried to 50% water concentration before resaturation.

Bauer, A.↗
NASA NTRS1984

Properties of simulated comet mantle

The properties of freeze-dried dilute dispersions of dust in water ice are of considerable interest in studies of comet nucleus mantles. The formation of a rind residue produced by the sublimation of water ice containing various amounts of fine clay particles may be an important process. A simulation of the development of the dry dust rind on the surface of comets is presented. This rind is the result of preferential ice sublimation. The development and disruption of this rind and its subsequent levitation by water vapor flow is studied. The most interesting rind simulant is produced by dispersing 0.1 micron particles of montmorillonite in water in concentrations of 10%, 1%, and 0.1%. These dispersions are then sprayed into liquid nitrogen in the form of 100 micron droplets. The frozen droplets are then freeze-dried in a vacuum which prevents the ice temperature from rising above -30 C. Sublimation of the nitrogen and the water produced dry rinds. The most striking result was the development of large cohesive matrices of individual clay particles, and in some cases a continuous cohesive crust. Scanning electron microscope (SEM) observations reveal that the material formed by freeze-drying the 0.1% dispersion does not retain the original spherical shape of the sprayed 100 micron droplets; instead it consists of a continuous filamentary network, as shown in the SEM stereo micrographs.

Fanale, F. P.↗
NASA NTRS1992

Properties data for opening the Galileo's partially unfurled main antenna

An investigation was conducted into the friction and wear behavior of both unlubricated and dry-film-lubricated (Tiolube 460) titanium alloy (Ti-6Al-4V) in contact with an uncoated high-nickel-content superalloy (Inconel 718) both in vacuum and in air. The acquisition of friction and wear data for this sliding couple was motivated by the need for input data for the 'antenna stuck ribs model' effort to free Galileo's High Gain Antenna. The results of the investigation indicate that galling occurred in the unlubricated system in vacuum and that the coefficient of friction increased to 1.2. The abnormally high friction (1.45) was observed when relatively large wear debris clogged at the sliding interface. The coefficient of friction for the dry-film-lubricated system in vacuum is 0.04, while the value in air is 0.13. The endurance life of the dry-film lubricant is about three orders of magnitude greater in vacuum than in air. The worn surfaces of the dry-film-lubricated Ti-6Al-4V pin and Inconel 718 disk first run in humid air and then rerun in vacuum was completely different from that of the pin and disk run only in vacuum. When galling occurred in the humid-air and vacuum contact, coefficient of friction rose to 0.32 when sliding in humid air and to 1.4 when sliding in vacuum. The galling was accompanied by severe surface damage and extensive transfer of the Ti-6Al-4V to the Inconel 718, or vice versa. When spalling occurred in the dry-film-lubricated Ti-6Al-4V pin run only in vacuum, the coefficient of friction rose to 0.36 or greater. The wear damage caused by spalling can self-heal when rerun in vacuum - the coefficient of friction decreased to 0.05. The friction and wear data obtained can be used for the 'antenna stuck ribs model' effort to free Galileo's high gain antenna.

Miyoshi, Kazuhisa↗
NASA NTRS2001

Relative Influence of Initial Surface and Atmospheric Conditions on Seasonal Water and Energy Balances

We constructed and analyzed wet and dry soil moisture composites for the mid-latitude GCIP region of the central US using long climate model simulations made with the NCAR CCM3 and reanalysis products from NCEP. Using the diagnostic composites as a guide, we have completed a series of predictability experiments in which we imposed soil water initial conditions in CCM3 for the GCIP region for June 1 from anomalously wet and dry years, with atmospheric initial conditions taken from June 1 of a year with 'near-normal' soil water, and initial soil water from the near-normal year and atmospheric initial conditions from the wet and dry years. Preliminary results indicate that the initial state of the atmosphere is more important than the initial state of soil water determining the subsequent late spring and summer evolution of sod water over the GCIP region. Surprisingly, neither the composites or the predictability experiments yielded a strong influence of soil moisture on the atmosphere. To explore this further, we have made runs with extreme dry soil moisture initial anomalies imposed over the GCIP region (the soil close to being completely dry). These runs did yield a very strong effect on the atmosphere that persisted for at least three months. We conclude that the magnitude of the initial soil moisture anomaly is crucial, at least in CCM3, and are currently investigating whether a threshold exists, below which little impact is seen. In a complementary study, we compared the impact of the initial condition of snow cover versus the initial atmospheric state over the western US (corresponding to the westward extension of the GAPP program follow-on to GCIP). In this case, the initial prescription of snow cover is far more important than the initial atmospheric state in determining the subsequent evolution of snow cover. We are currently working to understand the very different soil water and snow cover results.

Oglesby, Robert J.↗