SEARCH · Search NASA

Results for “Experimental Test Range”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

NASA NTRS1944

Normal pressure tests on unstiffened flat plates

Flat sheet panels of aluminum alloy (all 17S-T except for two specimens of 24S-T) were tested under normal pressures with clamped edge supports in the structures laboratory of the Guggenheim Aeronautical Laboratory, California Institute of Technology. The thicknesses used ranged from 0.010 to 0.080 inch; the panel sizes ranged from 10 by 10 inches to 10 by 40 inches; and the pressure range was from 0 to 60-pounds-per-square-inch gage. Deflection patterns were measured and maximum tensile strains in the center of the panel were determined by electric strain gages. The experimental data are presented by pressure-strain, pressure-maximum-deflection, and pressure-deflection curves. The results of these tests have been compared with the corresponding strains and deflections as calculated by the simple membrane theory and by large deflection theories.

Head, Richard M↗

NASA NTRS1980

Experimental aerodynamic and acoustic model testing of the Variable Cycle Engine (VCE) testbed coannular exhaust nozzle system

Aerodynamic performance and jet noise characteristics of a one sixth scale model of the variable cycle engine testbed exhaust system were obtained in a series of static tests over a range of simulated engine operating conditions. Model acoustic data were acquired. Data were compared to predictions of coannular model nozzle performance. The model, tested with an without a hardwall ejector, had a total flow area equivalent to a 0.127 meter (5 inch) diameter conical nozzle with a 0.65 fan to primary nozzle area ratio and a 0.82 fan nozzle radius ratio. Fan stream temperatures and velocities were varied from 422 K to 1089 K (760 R to 1960 R) and 434 to 755 meters per second (1423 to 2477 feet per second). Primary stream properties were varied from 589 to 1089 K (1060 R to 1960 R) and 353 to 600 meters per second (1158 to 1968 feet per second). Exhaust plume velocity surveys were conducted at one operating condition with and without the ejector installed. Thirty aerodynamic performance data points were obtained with an unheated air supply. Fan nozzle pressure ratio was varied from 1.8 to 3.2 at a constant primary pressure ratio of 1.6; primary pressure ratio was varied from 1.4 to 2.4 while holding fan pressure ratio constant at 2.4. Operation with the ejector increased nozzle thrust coefficient 0.2 to 0.4 percent.

Nelson, D. P.↗

NASA NTRS2009

Aerothermodynamic Characteristics of Boundary Layer Transition and Trip Effectiveness of the HIFiRE Flight 5 Vehicle

An experimental wind tunnel test was conducted in the NASA Langley Research Center s 20-Inch Mach 6 Tunnel in support of the Hypersonic International Flight Research Experimentation Program. The information in this report is focused on the Flight 5 configuration, one in a series of flight experiments. This report documents experimental measurements made over a range of Reynolds numbers and angles of attack on several scaled ceramic heat transfer models of the Flight 5 vehicle. The heat transfer rate was measured using global phosphor thermography and the resulting images and heat transfer rate distributions were used to infer the state of the boundary layer on the windside, leeside and side surfaces. Boundary layer trips were used to force the boundary layer turbulent, and a study was conducted to determine the effectiveness of the trips with various heights. The experimental data highlighted in this test report were used determine the allowable roughness height for both the windside and side surfaces of the vehicle as well as provide for future tunnel-to-tunnel comparisons.

Berger, Karen T.↗

NASA NTRSDate not supplied

Efficient Variable-Pitch Propeller Aerodynamic Model Development for Vectored-Thrust eVTOL Aircraft

This paper describes a variable-pitch propeller testing and aerodynamic modeling methodology for electric vertical takeoff and landing (eVTOL) aircraft using wind tunnel testing. Propellers used for eVTOL aircraft propulsion systems experience a wide range of operating conditions resulting in significant variation of axial thrust and torque, as well as off-axis forces and moments, across a typical flight envelope. An experimental design is developed to collect informative wind tunnel data in an efficient manner using response surface methods. System identification methods are then applied to isolated propeller wind tunnel data to develop a mathematical model of the propeller valid throughout the transition envelope of a vectored-thrust eVTOL aircraft. Multiple explanatory variable definitions are postulated and compared using modeling and prediction performance metrics. Modeling results validated against data withheld from the modeling process indicate good predictive capability and agree with theoretical expectations. All identified propeller models are provided, which allows the models to be used in future eVTOL aircraft flight dynamics simulations.

aerodynamic modeling↗

NASA NTRSDate not supplied

Assessment of Using Ideal Gas for Predicting Boattail Flow at Cryogenic Temperatures

The applicability of using ideal gas assumptions to simulate high Reynolds number experimental data that was obtained at cryogenic temperatures is examined. Flow over an axisymmetric nozzle boattail model was calculated using reference temperatures of 117 K and 300 K and at Reynolds numbers from 50 to 200 million per meter. From the testing perspective, pressure, compression factor, and isentropic coefficients calculated using one-dimensional real gas equations are used to examine the departure of cryogenic flow from ideal gas flow across the range of temperatures and potential impacts on measured aerodynamic data. Solutions developed using ideal gas assumptions in a three-dimensional Navier-Stokes code are compared with experimental data obtained at cryogenic temperatures at two unit Reynolds numbers at freestream Mach numbers of 0.6 and 0.9. Results for several one- and two-equation turbulence models are shown. Predicted pressure coefficient distributions along the nozzle boattail differed from experimental data between 8% to less than 0.5% depending on the turbulence model and Mach number. The greatest discrepancy occurred in the level of static pressure recovery in the recompression region where the flow was separated. Solutions using warm and cryogenic freestream temperatures predicted similar boattail pressure distributions at the same unit Reynolds number.

Nozzle↗

NASA NTRSDate not supplied

Assessment of Using Ideal Gas for Predicting Boattail Flow at Cryogenic Temperatures

Nozzle↗

NASA NTRS1975

Cold-air annular-cascade investigation of aerodynamic performance of core-engine-cooled turbine vanes. 1: Solid-vane performance and facility description

The aerodynamic performance of a solid (uncooled) version of a core engine cooled stator vane was experimentally determined in a full-annular cascade, where three-dimensional effects could be obtained. The solid vane, which serves as a basis for comparison with subsequent cooled tests, was tested over a range of aftermixed critical velocity ratios of 0.57 to 0.90. Overall vane aftermixed efficiencies were obtained over this critical velocity ratio range and compared with results from a two-dimensional cascade. The variation in vane efficiency and aftermixed flow conditions with circumferential and radial position were obtained and compared with design values. Vane surface static-pressure distributions were also measured and compared with theoretical results.

Goldman, L. J.↗

NASA NTRS1975

Impact fracture of composite sandwich structures

An experimental investigation of impact-initiated failures in high-strength graphite/epoxy and Kevlar-49/epoxy sandwich structures has been conducted. The tests consisted of firing small diameter aluminum projectiles with a velocity range of 16-67 meters/second (52-220 ft/sec) at preloaded sandwich specimens. These tests were intended to be representative of service conditions on materials and structures which might be used as secondary aircraft components. The preload and impact energy necessary to initiate catastrophic failure were determined. The residual strength of impact-damaged specimens was also measured. The results of these tests indicate that catastrophic failures in sandwich structures can be initiated at relatively low preloads by impact projectiles at energy levels well below that required to initiate visible damage.

Rhodes, M. D.↗

NASA NTRS1985

Ablation of Galileo Probe heat-shield models in a ballistic range

Several 1/24-scale models of the Galileo Probe made of carbon-phenolic materials were flown in a ballistic range to test their ablation characteristics. Mostly radiative or all-convective heating environments were produced by using argon or air as the test gas, respectively, to simulate the Jovian entry heating environments. The experimental results were compared with the theoretical predictions made using the computer codes of radiating shock layer environment (RASLE) and charring materials ablation (CMA). The experimental data obtained in argon agreed approximately with the theoretical predictions. The data for air agreed approximately with the theory when turbulence and surface roughness effects were accounted for. The data imply that the Galileo Probe heat shield was adequately designed.

Park, C.↗

NASA NTRS1984

Experimental Results for a Flapped Natural-laminar-flow Airfoil with High Lift/drag Ratio

Experimental results have been obtained for a flapped natural-laminar-flow airfoil, NLF(1)-0414F, in the Langley Low-Turbulence Pressure Tunnel. The tests were conducted over a Mach number range from 0.05 to 0.40 and a chord Reynolds number range from about 3.0 x 10(6) to 22.0 x 10(6). The airfoil was designed for 0.70 chord laminar flow on both surfaces at a lift coefficient of 0.40, a Reynolds number of 10.0 x 10(6), and a Mach number of 0.40. A 0.125 chord simple flap was incorporated in the design to increase the low-drag, lift-coefficient range. Results were also obtained for a 0.20 chord split-flap deflected 60 deg.

Mcghee, R. J.↗

NASA NTRS1986

Damage-induced property changes in composites subjected to cyclic thermal loading

Damage in the form of transverse cracks resulting from thermal loading is studied as it relates to the dimensional stability of flat laminates and stiffness changes in cylindrical tubes. Graphite-epoxy specimens were subjected to cyclic thermal loading in the temperature range -250 to + 250 F. It is shown that transverse cracking is the dominant damage mechanism in both types of structural elements. Fiber splitting is also quite common at the low test temperatures. Experimental results indicate that damage significantly reduces the inplane coefficients of thermal expansion of flat laminates and the torsional stiffness of the tubes. Theoretical predictions for coefficients of thermal expansion as a function of crack spacing in flat laminates followed the same trend as experimental results.

Herakovich, Carl T.↗

NASA NTRS1987

Current status of the Iosipescu shear test method

During the past several years, considerable study of the Iosipescu shear test method has been conducted by a number of investigators, including the present authors. Several different test fixture designs have been developed, and variations of the specimen size and notch configuration have been considered. Materials with properties ranging from isotropic to highly orthotropic have been tested. The response of such materials has also been predicted using finite element techniques, and attempts have been made to correlate these predictions with available experimental data. This recent work is summarized here, with particular emphasis being given to the correlations and contradictions resulting from the published works of these various investigators.

Adams, Donald F.↗

NASA NTRS1994

A Modified Mixing Length Turbulence Model for Zero and Adverse Pressure Gradients

The modified mixing length (MML) turbulence model was installed in the Proteus Navier-Stokes code, then modified to make it applicable to a wider range of flows typical of aerospace propulsion applications. The modifications are based on experimental data for three flat-plate flows having zero, mild adverse, and strong adverse pressure gradients. Three transonic diffuser test cases were run with the new version of the model in order to evaluate its performance. All results are compared with experimental data and show improvements over calculations made using the Baldwin-Lomax turbulence model, the standard algebraic model in Proteus.

Conley, Julianne M.↗

NASA NTRS1996

Baseline acoustic levels of the NASA Active Noise Control Fan rig

Extensive measurements of the spinning acoustic mode structure in the NASA 48 inch Active Noise Control Fan (ANCF) test rig have been taken. A continuously rotating microphone rake system with a least-squares data reduction technique was employed to measure these modes in the inlet and exhaust. Farfield directivity patterns in an anechoic environment were also measured at matched corrected rotor speeds. Several vane counts and spacings were tested over a range of rotor speeds. The Eversman finite element radiation code was run with the measured in-duct modes as input and the computed farfield results were compared to the experimentally measured directivity pattern. The experimental data show that inlet spinning mode measurements can be made very accurately. Exhaust mode measurements may have wake interference, but the least-squares reduction does a good job of rejecting the non-acoustic pressure. The Eversman radiation code accurately extrapolates the farfield levels and directivity pattern when all in-duct modes are included.

Sutliff, Daniel L.↗

NASA NTRS2000

Southern Africa Validation of NASA's Earth Observing System (SAVE EOS)

Southern Africa Validation of EOS (SAVE) is 4-year, multidisciplinary effort to validate operational and experimental products from Terra-the flagship satellite of NASA's Earth Observing System (EOS). At test sites from Zambia to South Africa, we are measuring soil, vegetation and atmospheric parameters over a range of ecosystems for comparison with products from Terra, Landsat 7, AVHRR and SeaWiFS. The data are also employed to parameterize and improve vegetation process models. Fixed-point and mobile "transect" sampling are used to collect the ground data. These are extrapolated over larger areas with fine-resolution multispectral imagery. We describe the sites, infrastructure, and measurement strategies developed underSAVE, as well as initial results from our participation in the first Intensive Field Campaign of SAFARI 2000. We also describe SAVE's role in the Kalahari Transect Campaign (February/March 2000) in Zambia and Botswana.

Privette, Jeffrey L.↗

NASA NTRS1998

Reusable Metallic Thermal Protection Systems Development

Metallic thermal protection systems (TPS) are being developed to help meet the ambitious goals of future reusable launch vehicles. Recent metallic TPS development efforts at NASA Langley Research Center are described. Foil-gage metallic honeycomb coupons, representative of the outer surface of metallic TPS were subjected to low speed impact, hypervelocity impact, rain erosion, and subsequent arcjet exposure. TPS panels were subjected to thermal vacuum, acoustic, and hot gas flow testing. Results of the coupon and panel tests are presented. Experimental and analytical tools are being developed to characterize and improve internal insulations. Masses of metallic TPS and advanced ceramic tile and blanket TPS concepts are compared for a wide range of parameters.

Blosser, Max L.↗

NASA NTRS2009

Heat Transfer Modeling and Validation for Optically Thick Alumina Fibrous Insulation

Combined radiation/conduction heat transfer through unbonded alumina fibrous insulation was modeled using the diffusion approximation for modeling the radiation component of heat transfer in the optically thick insulation. The validity of the heat transfer model was investigated by comparison to previously reported experimental effective thermal conductivity data over the insulation density range of 24 to 96 kg/cu m, with a pressure range of 0.001 to 750 torr (0.1 to 101.3 x 10(exp 3) Pa), and test sample hot side temperature range of 530 to 1360 K. The model was further validated by comparison to thermal conductivity measurements using the transient step heating technique on an insulation sample at a density of 144 kg/cu m over a pressure range of 0.001 to 760 torr, and temperature range of 290 to 1090 K.

Daryabeigi, Kamran↗

NASA NTRS2012

Lightweight, High-Temperature Radiator for Space Propulsion

For high-power nuclear-electric spacecraft, the radiator can account for 40% or more of the power system mass and a large fraction of the total vehicle mass. Improvements in the heat rejection per unit mass rely on lower-density and higher-thermal conductivity materials. Current radiators achieve near-ideal surface radiation through high-emissivity coatings, so improvements in heat rejection per unit area can be accomplished only by raising the temperature at which heat is rejected. We have been investigating materials that have the potential to deliver significant reductions in mass density and significant improvements in thermal conductivity, while expanding the feasible range of temperature for heat rejection up to 1000 K and higher. The presentation will discuss the experimental results and models of the heat transfer in matrix-free carbon fiber fins. Thermal testing of other carbon-based fin materials including carbon nanotube cloth and a carbon nanotube composite will also be presented.

Hyers, R. W.↗