Search NASA⌕ Search

SEARCH · Search NASA

Results for “FASTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Final Report on Actinide Glass Scintillators for Fast Neutron Detection

This is the final report of an experimental investigation of actinide glass scintillators for fast-neutron detection. It covers work performed during FY2012. This supplements a previous report, PNNL-20854 “Initial Characterization of Thorium-loaded Glasses for Fast Neutron Detection” (October 2011). The work in FY2012 was done with funding remaining from FY2011. As noted in PNNL-20854, the glasses tested prior to July 2011 were erroneously identified as scintillators. The decision was then made to start from “scratch” with a literature survey and some test melts with a non-radioactive glass composition that could later be fabricated with select actinides, most likely thorium. The normal stand-in for thorium in radioactive waste glasses is cerium in the same oxidation state. Since cerium in the 3+ state is used as the light emitter in many scintillating glasses, the next most common substitute was used: hafnium. Three hafnium glasses were melted. Two melts were colored amber and a third was clear. It barely scintillated when exposed to alpha particles. The uses and applications for a scintillating fast neutron detector are important enough that the search for such a material should not be totally abandoned. This current effort focused on actinides that have very high neutron capture energy releases but low neutron capture cross sections. This results in very long counting times and poor signal to noise when working with sealed sources. These materials are best for high flux applications and access to neutron generators or reactors would enable better test scenarios. The total energy of the neutron capture reaction is not the only factor to focus on in isotope selection. Many neutron capture reactions result in energetic gamma rays that require large volumes or high densities to detect. If the scintillator is to separate neutrons from gamma rays, the capture reactions should produce heavy particles and few gamma rays. This would improve the detection of a signal for fast neutron capture.

Actinide Glass↗

Final Project Report "Advanced Concept Exploration For Fast Ignition Science Program"

The Fast Ignition (FI) Concept for Inertial Confinement Fusion has the potential to provide a significant advance in the technical attractiveness of Inertial Fusion Energy (IFE) reactors. FI differs from conventional “central hot spot” (CHS) target ignition by decoupling compression from heating: using the laser (or heavy ion beam or Z pinch) drive pulse (10’s of ns) to create a dense fuel and a second, much shorter (~10 ps) high intensity pulse to ignite a small region of it. There are two major physics issues concerning this concept; controlling the laser-induced generation of large electron currents and their propagation through high density plasmas. This project has addressed these two significant scientific issues in Relativistic High Energy Density (RHED) physics. Learning to control relativistic laser matter interaction (and the limits and potential thereof) will enable a wide range of applications. While these physics issues are of specific interest to inertial fusion energy science, they are also important for a wide range of other HED phenomena, including high energy ion beam generation, isochoric heating of materials, and the development of high brightness x-ray sources. Generating, controlling, and understanding the extreme conditions needed to advance this science has proved to be challenging: Our studies have pushed the boundaries of physics understanding and are at the very limits of experimental, diagnostic, and simulation capabilities in high energy density laboratory physics (HEDLP). Our research strategy has been based on pursuing the fundamental physics underlying the Fast Ignition (FI) concept. We have performed comprehensive study of electron generation and transport in fast-ignition targets with experiments, theory, and numerical modeling. A major issue is that the electrons produced in these experiments cannot be measured directly—only effects due to their transport. We focused mainly on x-ray continuum photons from bremsstrahlung and x-ray line radiation from K-shell fluorescence. Integrated experiments, which combine target compression with short-pulse laser heating, yield additional information on target heating efficiency. This indirect way of studying the underlying behavior of the electrons must be validated with computational modeling to understand the physics and improve the design. This program execution required a large, well-organized team and it was managed by a joint Collaboration between General Atomics (GA), Lawrence Livermore National Laboratory (LLNL), and the Laboratory for Laser Energetics (LLE). The Collaboration was formed 8 years ago to understand the physics issues of the Fast Ignition concept, building on the strengths of each partner. GA fulfills its responsibilities jointly with the University of California, San Diego (UCSD), The Ohio State University (OSU) and the University of Nevada at Reno (UNR). Since RHED physics is pursued vigorously in many countries, international researchers have been an important part of our efforts to make progress. The division of responsibility was as follows: (1) LLE had primary leadership for channeling studies and the integrated energy transfer, (2) LLNL led the development of measurement methods, analysis, and deployment of diagnostics, and (3) GA together with UCSD, OSU and UNR studied the detailed energy-transfer physics. The experimental program was carried out using the Titan laser at the Jupiter Laser Facility at LLNL, the OMEGA and OMEGA EP lasers at LLE and the Texas Petawatt laser (TPW) at UT Austin. Modeling has been pursued on large computing facilities at LLNL, OSU, and UCSD using codes developed (by us and others) within the HEDLP program, commercial codes, and by leveraging existing supercomputer codes developed by the NNSA ICF program. This Consortium brought together all the components—resources, facilities, and personnel—necessary to accomplish its aggressive goals. The ACE Program has been strongly collaborative, taking advantage of the expertise of the participating institutions to provide a research effort that is far greater than the sum of its parts. The results of this work have firmly strengthened the scientific foundation from which the viability of FI and other applications can be evaluated. Program execution has also led to improved diagnostics for probing dense, hot plasmas, detailed understanding of high-current, relativistic electron energy generation and transport across boundaries and into dense plasmas, and greatly enhanced predictive modeling capabilities. One important aspect of this program was the involvement and training of young scientists including postdoctoral fellows and graduate students. During the entire 8 years of FI and ACE project period since 2005, more than fifteen graduate students completed their doctoral dissertations including three from OSU and two from UCSD in last three years. This project generated an impressive forty articles in high quality journals including nine (including two under review) in Physical Review Letters during the last funding period since 2011.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Propagation And Damping Of High Harmonic Fast Waves And Electron Cyclotron Waves In The Nstx-U-Device

For the spherical torus and for conventional tokamaks to be viable means of producing fusion energy there are two important requirements. The first is to heat the plasma in the experimental devices to high temperatures; preferably, to fusion relevant temperatures. The second is to drive a current in the plasma so that the fusion device operates in a steady-state mode. A pulsed fusion reactor for energy production is not desirable. A favored means to achieve both of these requirements is through the use of microwaves, commonly referred to as radio frequency waves. This proposal was to understand observations from the National Spherical Torus Experiment Upgrade (NSTX-U) device on radio frequency wave heating of the confined plasma during operations with high harmonic fast waves. The proposed research was also directed toward assisting in the optimization of the experimental modes of operation so as to maximize the heating efficiency. A detailed analysis of the experiments has shown that about one-third of the input radio frequency power does not make it into the core region of the plasma where heating is required. The losses are believed to occur primarily in the edge region where the radio frequency power is initially coupled into the plasma. Using sophisticated computational codes and theoretical models, that have been developed for the NSTX-U experimental program, this research quantified the physical processes which occur in the edge plasma and lead to a decrease in the heating efficiency. The effect of edge turbulence on the scattering of radio frequency waves was studied for waves in the ion cyclotron and electron cyclotron range of frequencies. For high harmonic fast waves in the ion cyclotron range of frequencies, simulations were carried out using a full-wave solver that was extended to the vacuum vessel wall. These simulations successfully reproduced trends that were observed experimentally. This simulation capability was also used to study the interaction of high harmonic fast waves with the scrape-off layer plasma. More recently, a new technique has been developed for the calculation of radio frequency waves in toroidal geometry that enables the simultaneous incorporation of antenna geometry, plasma facing components, the scrape off-layer, and core propagation in the high harmonic fast wave regime. The effect of turbulent plasmas on the mode conversion of extraordinary electromagnetic waves in the electron cyclotron range of frequencies in the NSTX-U plasma has been studied theoretically. In the over-dense plasmas of NSTX-U, the traditional electromagnetic waves are not effective for delivering energy and momentum to the core plasma. However, electron Bernstein waves generated by mode conversion are efficient carriers of wave energy and momentum to the core. The mode conversion occurs in the turbulent edge region. A theory for mode conversion in such plasmas has been developed. The parameters that can optimize the mode conversion can be readily determined. Also, the model is useful for experimentalists to analyze observation on a shot-to-shot basis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Propagation And Damping Of High Harmonic Fast Waves And Electron Cyclotron Waves In The Nstx-U-Device

For the spherical torus and for conventional tokamaks to be viable means of producing fusion energy there are two important requirements. The first is to heat the plasma in the experimental devices to high temperatures; preferably, to fusion relevant temperatures. The second is to drive a current in the plasma so that the fusion device operates in a steady-state mode. A pulsed fusion reactor for energy production is not desirable. A favored means to achieve both of these requirements is through the use of microwaves, commonly referred to as radio frequency waves. This proposal was to understand observations from the National Spherical Torus Experiment Upgrade (NSTX-U) device on radio frequency wave heating of the confined plasma during operations with high harmonic fast waves. The proposed research was also directed toward assisting in the optimization of the experimental modes of operation so as to maximize the heating efficiency. A detailed analysis of the experiments has shown that about one-third of the input radio frequency power does not make it into the core region of the plasma where heating is required. The losses are believed to occur primarily in the edge region where the radio frequency power is initially coupled into the plasma. Using sophisticated computational codes and theoretical models, that have been developed for the NSTX-U experimental program, this research quantified the physical processes which occur in the edge plasma and lead to a decrease in the heating efficiency. The effect of edge turbulence on the scattering of radio frequency waves was studied for waves in the ion cyclotron and electron cyclotron range of frequencies. For high harmonic fast waves in the ion cyclotron range of frequencies, simulations were carried out using a full-wave solver that was extended to the vacuum vessel wall. These simulations successfully reproduced trends that were observed experimentally. This simulation capability was also used to study the interaction of high harmonic fast waves with the scrape-off layer plasma. More recently, a new technique has been developed for the calculation of radio frequency waves in toroidal geometry that enables the simultaneous incorporation of antenna geometry, plasma facing components, the scrape off-layer, and core propagation in the high harmonic fast wave regime. The effect of turbulent plasmas on the mode conversion of extraordinary electromagnetic waves in the electron cyclotron range of frequencies in the NSTX-U plasma has been studied theoretically. In the over-dense plasmas of NSTX-U, the traditional electromagnetic waves are not effective for delivering energy and momentum to the core plasma. However, electron Bernstein waves generated by mode conversion are efficient carriers of wave energy and momentum to the core. The mode conversion occurs in the turbulent edge region. A theory for mode conversion in such plasmas has been developed. The parameters that can optimize the mode conversion can be readily determined. Also, the model is useful for experimentalists to analyze observation on a shot-to-shot basis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Considerations for Corridor and Community DC Fast Charging Complex System Design

The Idaho National Laboratory (INL), a U.S. Department of Energy (DOE) national laboratory located in Idaho Falls, Idaho, has been DOE’s lead laboratory for the field testing of light-duty plug-in electric vehicles (PEVs), charging infrastructure, and other alternative vehicle technologies for 25 years. INL has tested and collected data from more than 17,000 charging stations, documenting efficiencies, charge profiles, and PEV drivers’ behaviors when using charging infrastructure. Based on the experience of INL staff and support personnel, DOE requested that INL perform three tasks: • Identify pertinent lessons learned from previous direct current (DC) fast charger (DCFC) deployment and data collection activities in order to perform an analysis of the experience to date with DC fast charging systems • Establish the criteria for siting DC fast charging systems, including access to current or future sizeable penetrations of PEVs and existing power, the potential to be used by local (intracity) as well as pass-through (intercity) PEV drivers, expandability, and accessible to the federal highway system • Develop a draft system specification that lists the components that will be incorporated in a DC fast charging complexes.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Development of a Fast Spectrum Test Loop at the Advanced Test Reactor

The United States currently has no infrastructure to provide a fast neutron flux for research purposes. With the increased interest in Sodium Fast Reactor (SFR) technology, this type of infrastructure is necessary for further development of key components such as Versatile Test Reactor. The purpose of this research is to characterize the thermal hydraulics of a test loop capable of providing SFR like operating conditions. This includes showcasing feasibility in mechanical design, reaching a high fast to thermal neutron flux ratio ideally near 15, an inlet temperature of 600 K, a temperature increase of 50 K from inlet to outlet, and test chamber radial temperature profiles similar to SFR fuel rods. Existing infrastructure must be used to provide the neutron flux for the test loop, and it was decided that the Advanced Test Reactor (ATR) was the optimal choice due to its availability and previous work conducted similar to this project. To achieve the goals of this project, several mechanical designs were put forward with the most feasible design being chosen. The neutronics and thermal hydraulics analysis were conducted in tandem, with an iterative process used to maximize efficiency of both systems. Analysis of the neutronics system was done using Attila and MCNP while the thermal hydraulic analysis was done using RELAP5. This document outlines the thermal hydraulic analysis, though it includes the results from the mechanical design and neutronics analysis. The loop design includes a primary system with molten sodium, a set of “booster fuel plates” to increase the fast flux within the test section, a water system to cool the booster fuel plates, a helium system to separate the sodium and water systems, and a thermal neutron shield to decrease the thermal flux. Each of these systems is modeled in the neutronics and thermal hydraulic analyses. The RELAP5 model showcased the feasibility of the design proposed by this report. For all designs tested, the desired 50 K temperature increase from inlet to outlet was reached. The fuel rod radial temperature profile was lower than was expected, likely due to a lower rod thermal power than expected. A parametric study was also conducted to characterize the system with three fuel pins. This study showed the effect of thermal power, fluid pressure, fluid velocity, and inlet temperature on the system. ©Copyright by Anton Higgins December 11, 2019 All Rights Reserved

99 GENERAL AND MISCELLANEOUS↗

FAST FY 2018 Data Call: A Preliminary Review [Slides]

This presentation provides an overview of fiscal year 2018 federal motor vehicle fleet data at the individual vehicle level during the fall of 2018, a preliminary summary of the data collected, and how the collecting project has reviewed that information for potential quality issues. This presentation will be given at the March 2019 INTERFUEL group meeting, hosted by DOE's Federal Energy Management Program (DOE FEMP). The information is collected through the Federal Automotive Statistical Tool (FAST) project. FAST is a Web-based information system managed by the US Department of Energy, the US General Services Administration, and the Energy Information Administration. FAST is used to collect information about the fleet of motor vehicles used and managed by the Federal government. FAST is developed and maintained by DOE's Idaho National Laboratory (INL).

99 GENERAL AND MISCELLANEOUS↗

Degradation and Failure Phenomena of Advanced Reactor Fuel Concepts: Sodium-Cooled Fast Reactor Metallic Fuel

The U.S. Nuclear Regulatory Commission (NRC) is anticipating licensing applications and commercial use of new fuel types in advanced nuclear power reactors that would be designed and built in the United States. Pacific Northwest National Laboratory (PNNL) is providing technical assistance to the NRC related to the newly proposed nuclear fuel and cladding designs that would be deployed in these reactors. This report focuses specifically on the metallic fuel that is being considered for sodium-cooled fast reactors and specifically on mechanisms that would cause damage or failure to the fuel under reactor operating conditions and design basis accident conditions. There is historic experience with both metallic and oxide fuels in experimental sodium-cooled fast reactors, but this report will focus solely on metallic fuel. Currently two U.S.-based reactor designers are engaged with the NRC in the application or pre-application review and considering a sodium-cooled fast reactor. TerraPower is engaged with NRC in pre-application review of its Natrium reactor. The current design for this fuel uses a sodium-bonded uranium-10wt% zirconium (U10Zr) fuel clad in HT9 stainless steel. ARC Clean Technology is engaged with NRC in pre-application review of its ARC-100 reactor. The current design for this fuel uses a sodium-bonded uranium-10wt% zirconium (U10Zr) fuel with steel cladding. This report will focus on this fuel system specifically, with broader information given regarding other metallic fuel systems with other stainless steel alloy claddings. To support the NRC’s readiness efforts, this report will identify and discuss degradation and failure modes of metallic fuel concepts for sodium-cooled fast reactors, including fuel performance characteristics that may not be addressed within existing regulatory documents.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Enhanced Model for Fast Ignition

Laser Fusion is a prime candidate for alternate energy production, capable of serving a major portion of the nation's energy needs, once fusion fuel can be readily ignited. Fast Ignition may well speed achievement of this goal, by reducing net demands on laser pulse energy and timing precision. However, Fast Ignition has presented a major challenge to modeling. This project has enhanced the computer code ePLAS for the simulation of the many specialized phenomena, which arise with Fast Ignition. The improved code has helped researchers to understand better the consequences of laser absorption, energy transport, and laser target hydrodynamics. ePLAS uses efficient implicit methods to acquire solutions for the electromagnetic fields that govern the accelerations of electrons and ions in targets. In many cases, the code implements fluid modeling for these components. These combined features, "implicitness and fluid modeling," can greatly facilitate calculations, permitting the rapid scoping and evaluation of experiments. ePLAS can be used on PCs, Macs and Linux machines, providing researchers and students with rapid results. This project has improved the treatment of electromagnetics, hydrodynamics, and atomic physics in the code. It has simplified output graphics, and provided new input that avoids the need for source code access by users. The improved code can now aid university, business and national laboratory users in pursuit of an early path to success with Fast Ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The New Modularization Framework for the FAST Wind Turbine CAE Tool

NREL has recently put considerable effort into improving the overall modularity of its FAST wind turbine aero-hydro-servo-elastic tool to (1) improve the ability to read, implement, and maintain source code; (2) increase module sharing and shared code development across the wind community; (3) improve numerical performance and robustness; and (4) greatly enhance flexibility and expandability to enable further developments of functionality without the need to recode established modules. The new FAST modularization framework supports module-independent inputs, outputs, states, and parameters; states in continuous-time, discrete-time, and in constraint form; loose and tight coupling; independent time and spatial discretizations; time marching, operating-point determination, and linearization; data encapsulation; dynamic allocation; and save/retrieve capability. This paper explains the features of the new FAST modularization framework, as well as the concepts and mathematical background needed to understand and apply it correctly. It is envisioned that the new modularization framework will transform FAST into a powerful, robust, and flexible wind turbine modeling tool with a large number of developers and a range of modeling fidelities across the aerodynamic, hydrodynamic, servo-dynamic, and structural-dynamic components.

17 WIND ENERGY↗

Effect of Si Content on Extreme Fast Charging Behavior in Silicon–Graphite Composite Anodes

Commercial Li-ion batteries typically incorporate a small amount of high-capacity silicon (Si)-based materials in the composite graphite-based anode to increase the energy density of the battery. However, very little is known about the effects of Si on the fast-charging behavior of composite anodes. Herein, we examine the effects of the Si/graphite ratio in the composite anode on the fast-charging behavior of full cells. We show that addition of Si increases the rate capability from 1C to 8C and improves the capacity retention in early cycles at 6C due to reduced overpotential in constant current charging cycles. The impacts of Si content on fast-charging aging were identified by Post-Test characterization. Despite realizing benefits of available capacity and reduced Li plating at 6C, silicon–electrolyte interactions lead the time-dependent cell performance to fade quickly in the long term. The Post-Test analysis also revealed the thickening of the electrode and nonuniform distribution of electrolyte decomposition products on the Si-containing anodes, as well as the organic-rich solid electrolyte interphase (SEI), which are the factors behind cell degradation. Our study sheds insight on the advantages and disadvantages of Si/graphite composite anodes when they are used in fast-charging applications and guides further research in the area by designing an optimized composition of Si incorporated in a mature graphite matrix.

25 ENERGY STORAGE↗

A Validation and Code-to-Code Verification of FAST for a Megawatt-Scale Wind Turbine with Aeroelastically Tailored Blades

This paper presents validation and code-to-code verification of the latest version of the U.S. Department of Energy, National Renewable Energy Laboratory wind turbine aeroelastic engineering simulation tool, FAST v8. A set of 1,141 test cases, for which experimental data from a Siemens 2.3 MW machine have been made available and were in accordance with the International Electrotechnical Commission 61400-13 guidelines, were identified. These conditions were simulated using FAST as well as the Siemens in-house aeroelastic code, BHawC. This paper presents a detailed analysis comparing results from FAST with those from BHawC as well as experimental measurements, using statistics including the means and the standard deviations along with the power spectral densities of select turbine parameters and loads. Results indicate a good agreement among the predictions using FAST, BHawC, and experimental measurements. Here, these agreements are discussed in detail in this paper, along with some comments regarding the differences seen in these comparisons relative to the inherent uncertainties in such a model-based analysis.

17 WIND ENERGY↗

Distinguishing Pu Metal From Pu Oxide Using Fast Neutron Counting

We describe a method for simultaneously determining the {alpha}-ratio and k{sub eff} for fissile materials using fast neutrons. Our method is a generalization of the Hage-Cifarrelli method for determining k{sub eff} for fissile assemblies which utilizes the shape of the fast neutron spectrum. In this talk we illustrate the method using Monte Carlo simulations of the fast neutrons generated in PuO{sub 2} to calculate the fast neutron spectrum and Feynman correlations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Plug-In Electric Vehicle Fast Charge Station Operational Analysis with Integrated Renewables: Preprint

The growing, though still nascent, plug-in electric vehicle (PEV) market currently operates primarily via level 1 and level 2 charging in the United States. Fast chargers are still a rarity, but offer a confidence boost to oppose 'range anxiety' in consumers making the transition from conventional vehicles to PEVs. Because relatively no real-world usage of fast chargers at scale exists yet, theNational Renewable Energy Laboratory developed a simulation to help assess fast charging needs based on real-world travel data. This study documents the data, methods, and results of the simulation run for multiple scenarios, varying fleet sizes, and the number of charger ports. The grid impact of this usage is further quantified to assess the opportunity for integration of renewables;specifically, a high frequency of fast charging is found to be in demand during the late afternoons and evenings coinciding with grid peak periods. Proper integration of a solar array and stationary battery thus helps ease the load and reduces the need for new generator construction to meet the demand of a future PEV market.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

High-Resolution Fast-Neutron Spectrometry for Arms Control and Treaty Verification

Many nondestructive nuclear analysis techniques have been developed to support the measurement needs of arms control and treaty verification, including gross photon and neutron counting, low- and high-resolution gamma spectrometry, time-correlated neutron measurements, and photon and neutron imaging. One notable measurement technique that has not been extensively studied to date for these applications is high-resolution fast-neutron spectrometry (HRFNS). Applied for arms control and treaty verification, HRFNS has the potential to serve as a complimentary measurement approach to these other techniques by providing a means to either qualitatively or quantitatively determine the composition and thickness of non-nuclear materials surrounding neutron-emitting materials. The technique uses the normally-occurring neutrons present in arms control and treaty verification objects of interest as an internal source of neutrons for performing active-interrogation transmission measurements. Most low-Z nuclei of interest for arms control and treaty verification, including 9Be, 12C, 14N, and 16O, possess fast-neutron resonance features in their absorption cross sections in the 0.5- to 5-MeV energy range. Measuring the selective removal of source neutrons over this energy range, assuming for example a fission-spectrum starting distribution, may be used to estimate the stoichiometric composition of intervening materials between the neutron source and detector. At a simpler level, determination of the emitted fast-neutron spectrum may be used for fingerprinting 'known' assemblies for later use in template-matching tests. As with photon spectrometry, automated analysis of fast-neutron spectra may be performed to support decision making and reporting systems protected behind information barriers. This paper will report recent work at Idaho National Laboratory to explore the feasibility of using HRFNS for arms control and treaty verification applications, including simulations and experiments, using fission-spectrum neutron sources to assess neutron transmission through composite low-Z attenuators.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

FAST v8 Verification and Validation for a Megawatt-Scale Wind Turbine with Aeroelastically Tailored Blades: Preprint

This paper presents findings from a verification and validation exercise on the latest version of the U.S. Department of Energy/National Renewable Energy Laboratory's in-house wind turbine aeroelastic design code FAST v8. Results from a set of 1141 FAST simulations were compared to those from Siemens' BHawC design code results, as well as experimental data from a heavily instrumented 2.3-MW Siemens wind turbine located at the National Wind Technology Center. The code validation was performed following the IEC-61400-13 standard, where a set of select quantities of interest from simulations at various wind speed and atmospheric turbulence conditions were used for a three-way comparison between FAST, BHawC, and the measurements. Results highlight many improvements of the latest version of FAST over its previous versions. This paper also provides comments from the authors on the data quality, and avenues for potential future work using these results.

17 WIND ENERGY↗

FAST: Continuing the Focus on Data Quality

This presentation provides an overview of fiscal year 2019 federal motor vehicle fleet data, collected at the individual vehicle level during the fall of 2019, how the the collecting project has reviewed that information for potential quality issues, how the quality of this year's data submission compare to the prior year, and recommendations for federal agencies in their efforts to continue to improve the quality of their submissions. This presentation will be given at the January 2020 FedFleet training event, hosted by the US General Services Administration in Washington, DC. The information is collected through the Federal Automotive Statistical Tool (FAST) project. FAST is a Web-based information system managed by the US Department of Energy, the US General Services Administration, and the Energy Information Administration. FAST is used to collect information about the fleet of motor vehicles used and managed by the Federal government. FAST is developed and maintained by DOE's Idaho National Laboratory (INL).

99 GENERAL AND MISCELLANEOUS↗

FAST FY 2018 Federal Fleet Data Call: Looking at Data Quality

This presentation provides an overview of fiscal year 2018 federal motor vehicle fleet data at the individual vehicle level during the fall of 2018, a preliminary summary of the data collected, how the the collecting project has reviewed that information for potential quality issues, and an overview of two key areas within the dataset that represent data quality issues. This presentation will be given at the April 2019 FedFleet training event, hosted by the US General Services Administration in Washington, DC. The information is collected through the Federal Automotive Statistical Tool (FAST) project. FAST is a Web-based information system managed by the US Department of Energy, the US General Services Administration, and the Energy Information Administration. FAST is used to collect information about the fleet of motor vehicles used and managed by the Federal government. FAST is developed and maintained by DOE's Idaho National Laboratory (INL).

99 GENERAL AND MISCELLANEOUS↗