Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel Cycle Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

A Modeling Study on Ammonia and Ammonia/Hydrogen Kinetics for Gas Turbine Engines

The use of ammonia as a fuel source in gas turbine engine power cycles represents an attractive means to decarbonize the energy sector due to higher energy density and achieving liquid state at far lower pressures compared to pure hydrogen. However, due to low flammability and a propensity for high NOx emissions, its use is not without challenge. Here, a number of 0D and 1D modeling tools were utilized to study the combustion characteristics of ammonia and ammonia/hydrogen mixtures, examining basic fundamental properties such as laminar flame speed, variability among existing chemical kinetic mechanisms, and considering the use of two-stage rich-lean combustion strategies to achieve low NOx emissions.

42 ENGINEERING↗

A New Reduced Order Model For The Mechanistic Creep Behavior Of UO 2

This manuscript describes an ongoing NEAMS effort to better determine the performance of advanced nuclear fuels, in particular the creep behavior of doped UO$_2$ for light water reactors. In our previous work, we outlined a method to utilize data generated from lower length scale simulations and implement it into the engineering scale fuel performance analysis. This process has been further refined, and in addition, new data has been used to train the surrogate model which has also been substantially improved since the previous iteration. The new model is compared against the current empirical model used in BISON using both scoping calculations to define the performance over the parameter space and using integral instrumented fuel assessment cases to determine the impact of these models on the overall fuel performance. Suggestions and guidance for future improvements to this method are provided to ensure the model covers relevant parameter space and phenomena.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advances in Geologic Disposal System Modeling and Application to Crystalline Rock

The Used Fuel Disposition Campaign (UFDC) of the U.S. Department of Energy (DOE) Office of Nuclear Energy (NE), Office of Fuel Cycle Technology (OFCT) is conducting research and development (R&D) on geologic disposal of used nuclear fuel (UNF) and high-level nuclear waste (HLW). Two of the high priorities for UFDC disposal R&D are design concept development and disposal system modeling (DOE 2011). These priorities are directly addressed in the UFDC Generic Disposal Systems Analysis (GDSA) work package, which is charged with developing a disposal system modeling and analysis capability for evaluating disposal system performance for nuclear waste in geologic media (e.g., salt, granite, clay, and deep borehole disposal). This report describes specific GDSA activities in fiscal year 2016 (FY 2016) toward the development of the enhanced disposal system modeling and analysis capability for geologic disposal of nuclear waste. The GDSA framework employs the PFLOTRAN thermal-hydrologic-chemical multi-physics code and the Dakota uncertainty sampling and propagation code. Each code is designed for massively-parallel processing in a high-performance computing (HPC) environment. Multi-physics representations in PFLOTRAN are used to simulate various coupled processes including heat flow, fluid flow, waste dissolution, radionuclide release, radionuclide decay and ingrowth, precipitation and dissolution of secondary phases, and radionuclide transport through engineered barriers and natural geologic barriers to the biosphere. Dakota is used to generate sets of representative realizations and to analyze parameter sensitivity.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

An Overview of the International Reactor Physics Experiment Evaluation Project

Interest in high-quality integral benchmark data is increasing as efforts to quantify and reduce calculational uncertainties associated with advanced modeling and simulation accelerate to meet the demands of next generation reactor and advanced fuel cycle concepts. Two Organization for Economic Cooperation and Development (OECD) Nuclear Energy Agency (NEA) activities, the International Criticality Safety Benchmark Evaluation Project (ICSBEP), initiated in 1992, and the International Reactor Physics Experiment Evaluation Project (IRPhEP), initiated in 2003, have been identifying existing integral experiment data, evaluating those data, and providing integral benchmark specifications for methods and data validation for nearly two decades. Data provided by those two projects will be of use to the international reactor physics, criticality safety, and nuclear data communities for future decades. An overview of the IRPhEP and a brief update of the ICSBEP are provided in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Cryogenic Viscous Compressor Development and Modeling for the ITER Vacuum System

The ITER vacuum system requires a roughing pump system that can pump the exhaust gas from the torus cryopumps to the tritium exhaust processing plant. The gas will have a high tritium content and therefore conventional vacuum pumps are not suitable. A pump called a cryogenic viscous compressor (CVC) is being designed for the roughing system to pump from ~500 Pa to 10 Pa at flow rates of 200 Pa-m3/ s. A unique feature of this pump is that is allows any helium in the gas to flow through the pump where it is sent to the detritiation system before exhausting to atmosphere. A small scale prototype of the CVC is being tested for heat transfer characteristics and compared to modeling results to ensure reliable operation of the full scale CVC. Keywords- ITER; vacuum; fuel cycle

fuel cycle↗

Recent Advancements and Prospects of Chemical Heat Pumps for Temperature Amplification for Nuclear Process Heat Applications

The energy economy is continually evolving, particularly in terms of primary energy sources, their conversions to useful forms such as electricity and heat, and their utilization in different sectors, in response to socio-political factors. Because nuclear energy source is a clean and non-carbon-emitting energy source, it is crucial to consider its role in the evolution of the energy economy. Integrated Energy Systems (IES) are collaboratively controlled systems that can dynamically apportion thermal and/or electrical energy to promote the production of various energy products and have the potential to reduce greenhouse gas (GHG) emissions, improve energy efficiency, improve electrical grid dependability, and enhance energy economics. To realize the benefits of IES with the current reactor fleets, selection and development of a complimentary temperature upgrading technology are necessary for providing process heat and improving economics.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Impact of fission product inclusion on phase development in U 3 Si 2 fuel

Due to its high thermal conductivity and uranium density, U 3 S i2 has been considered as a candidate for use as an accident tolerant fuel (ATF). In order to fully assess its suitability and performance as a fuel, the impact of fission products (FPs) on the stability and performance of U 3 Si 2 must be investigated. The interactions of FPs and U 3 Si 2 have had relatively little study until now and require experimental and computational examination. U 3 Si 2 was doped with individual FPs to explore U-Si-FP interactions and phase equilibria that may impact the performance of the ATF during irradiation. Elemental Ce, Mo, Y, or Zr were used to individually dope U 3 Si 2 at a concentration of 5 wt% FP. A diffusion couple of a 1:1 Mo:Zr alloy and U 3 Si 2 was heated to 1200 °C in order to consider the impacts of multiple FPs on the stability and structure of the fuel. Samples were characterized for FP solubility and secondary phase formation using electron microscopy, energy dispersive spectroscopy, and x-ray diffraction. First principles density functional theory calculations complemented the experimental effort to understand FP behavior. Experimental and computational findings were used in the development of a thermodynamic database containing 8 major FPs and their associated silicide phases. Finally, fuel compositions generated from depletion calculations were used to thermodynamically model the equilibrium phases of the fuel undergoing burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Control-Oriented Modeling of Cycle-to-Cycle Combustion Variability at the Misfire Limit in SI Engines

A control-oriented model is presented that can capture the prior-cycle correlation of combustion cycles during conditions with high levels of exhaust gas recirculation (EGR). Combustion events are modeled in discrete time and the dynamic evolution is captured by the residual air, fuel, and inert gas trapped in the combustion chamber. The mathematical formulation of the model is presented together with the calibration procedure to emulate a particular engine operating condition. A cycle-to-cycle system identification methodology is described which allows regressing model parameters from experimental data. Simulations are presented and compared to real engine measurements to show the modeling potential for analysis and control of combustion events.

Maldonado Puente, Bryan↗

Adsorbents and adsorption models for capture of Kr and Xe gas mixtures in fixed-bed columns

Off-gases produced during the reprocessing of used nuclear fuel (UNF) include 129-I 2 , 3-HHO, 14-CO 2 , 85-Kr, and 135-Xe, which are volatilized out into the off-gas. In order to meet regulatory requirements for reprocessing plant emissions, these gases must be captured and removed from the o?-gas stream prior to o?-gas emission. Of particular interest are the noble gases, Kr and Xe, which can be fairly difficult to remove from the off-gas due to their low chemical reactivity. Thus, this work is focused on utilizing engineered adsorbents, AgZ-PAN and HZ-PAN, to capture Kr and Xe from a mixed-gas stream at relatively low temperatures (191–295 K) and various flow rates (50–2000 mL/min). Isothermal data for Kr and Xe on each adsorbent are analyzed to produce the Langmuir parameters needed to model the mixture adsorption capacities at relevant temperatures using the Extended Langmuir model. Those parameters are then incorporated into a fixed-bed adsorption model developed in this work using the Mulitphysics Object-Oriented Simulation Environment (MOOSE). That model is used to simulate breakthrough times for Kr and Xe in packed columns of AgZ-PAN and HZ-PAN, ranging in length from 6 to 20 in., at relevant temperatures and flow rates. Breakthrough times varied from nearly instantaneous for Kr in AgZ-PAN to 30 h for Xe in HZ-PAN. After the developed model was validated by comparisons with experimental break-through data, the model framework was used to simulate the performance of multiple fixed-bed columns connected in series.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of a Thin Film Primary Surface Heat Exchanger for Advanced Power Cycles

This project objective is to develop a high-temperature design upgrade for an existing primary surface heat exchanger so that the redesigned hardware is capable of operation in CO 2 at temperatures up to 1,510°F (821°C) and pressure differentials up to 130 psi (9 bar). The heat exchanger is proposed for use as a recuperator in an advanced low-pressure oxy-fuel Brayton cycle that is predicted to achieve over 50% thermodynamic efficiency, although the heat exchanger could also be used in other high-temperature, low-differential pressure cycles. This report describes the progress to date, which includes continuing work performed to select and test new candidate materials for the recuperator redesign, final mechanical and thermal performance analysis results of various redesign concepts, and the preliminary design of a test loop for the redesigned recuperator including a budgetary estimate for detailed test loop design, procurement, and test operation. A materials search was performed in order to investigate high-temperature properties of many candidate materials, including high-temperature strength and nickel content. These properties were used to rank the candidate materials, resulting in a reduced list of nine materials for corrosion testing. Multiple test rigs were considered and analyzed for short-term corrosion testing and Thermal Gravimetric Analysis (TGA) was selected as the most cost-effective option for evaluating corrosion resistance of the candidate materials. In addition, tantalum, niobium, and chromium coatings were identified as potential options for increased corrosion resistance. The test results show that many materials exhibit relatively low weight gain rates, and that niobium and tantalum coatings may improve corrosion resistance for many materials, while chromium coatings appear to oxidize and debond quickly. Metallurgical analysis of alloys was also performed, showing evidence of intergranular attack in 282 that may cause long-term reliability problems in CO 2 service at these temperatures. However, long-term testing in a flowing environment is recommended in order to understand accurately the severity of the attack. Detailed economic modeling of the existing air cycle recuperator and CO 2 cycle recuperator options was also completed, including costs for material, fabrication, fuel, maintenance, and operation. The analysis results show that the increased capital cost for high-temperature materials may be offset by higher cycle efficiencies, decreasing the overall lifetime cost of the system. The economic analysis also examines costs associated with increased pressure drop and material changes for two redesign options. These results show that, even with slightly reduced performance and/or higher material costs, the lifetime cost per energy production may still be reduced by over 12%. The existing recuperator design information was provided by Solar Turbines, Inc. via several models, drawings, and design handoff meetings. Multiple fluid/thermal and structural models were created in order to analyze critical recuperator performance and mechanical strength in critical areas throughout the redesign process. These models were analyzed for a baseline condition (consistent with current Mercury 50 operation) for validation purposes. Results are presented for heat transfer coefficients and pressure drops, matching well with the existing operational data. Simulation of higher-temperature CO 2 conditions was also performed, showing a slight expected increase in both heat transfer and pressure drop. Mechanical analysis results for critical areas on the cross-flow and counter-flow sheets have also been obtained for air and CO 2 cases. These results show similar stresses in both cases but significantly reduced safety factors for the CO 2 case due to reduced yield and creep rupture strengths of alloy 625 at the higher temperatures. A concept brainstorm session and initial down-selection were completed in order to identify promising redesign options for further analysis. Detailed analysis of all promising redesign options was performed via finite element and computational fluid dynamic simulations in order to characterize mechanical and thermal-fluid performance of each option. These options included material change, various sheet thickness configurations, pitch and phasing of cross-flow and counter-flow sheets, and separator sheets. The analysis results have identified two viable redesign options that maintain existing safety margins optimally through a material change to Haynes 282 and (A) sheet thickness increases of 40% on the counter-flow sheet and 75% on the hot side cross-flow corrugation sheet or (B) addition of a separator sheet in the counter-flow section while maintaining the original counter-flow sheet thickness and increasing the cross-flow corrugation sheet thickness by 90% to account for the increase in cell height. While both options satisfy mechanical stress constraints, the separator sheet design has a higher part count, slightly reduced heat transfer, and slightly higher pressure drop than the first option and is not preferred. Finally, several test loop concepts have been developed for different full-scale and reduced-scale recuperator testing options. For each option, various loop components, such as heat exchangers, valves, heaters, and compressors, were evaluated in an effort to maximize utilization of existing resources. All concepts utilize an existing 3-MW CO 2 compressor, heater, and loop coolers, but the concepts vary by incorporating different amounts of new equipment for achieving various flow rates (all concepts operate at design pressure and temperature). The third concept achieves a 1 kg/s test without purchasing any costly equipment (coolers, heaters, blowers, etc.). Since the stacked cell design of the recuperator results in the same flow conditions at each core cell (even for a reduced-scale test). Thus, test loop Concept #3 was selected for the preliminary design. This loop design is detailed within the report, culminating in a budgetary estimate of $1,013,000.00 for the detailed design, construction, commissioning, and operation of a high-temperature recuperator test loop.

03 NATURAL GAS↗

AGR-2 safety test predictions using the PARFUME code

This report documents calculations performed to predict failure probability of TRISO-coated fuel particles and diffusion of fission products through these particles during safety tests following the second irradiation test of the Advanced Gas Reactor program (AGR-2). The calculations include the modeling of the AGR-2 irradiation that occurred from June 2010 to October 2013 in the Advanced Test Reactor (ATR) and the modeling of a safety testing phase to support safety tests planned at Oak Ridge National Laboratory and at Idaho National Laboratory (INL) for a selection of AGR-2 compacts. The heat-up of AGR-2 compacts is a critical component of the AGR-2 fuel performance evaluation, and its objectives are to identify the effect of accident test temperature, burnup, and irradiation temperature on the performance of the fuel at elevated temperature. Safety testing of compacts will be followed by detailed examinations of the fuel particles to further evaluate fission product retention and behavior of the kernel and coatings. The modeling was performed using the particle fuel model computer code PARFUME developed at INL. PARFUME is an advanced gas-cooled reactor fuel performance modeling and analysis code (Miller 2009). It has been developed as an integrated mechanistic code that evaluates the thermal, mechanical, and physico-chemical behavior of fuel particles during irradiation to determine the failure probability of a population of fuel particles given the particle-to-particle statistical variations in physical dimensions and material properties that arise from the fuel fabrication process, accounting for all viable mechanisms that can lead to particle failure. The code also determines the diffusion of fission products from the fuel through the particle coating layers, and through the fuel matrix to the coolant boundary. The subsequent release of fission products is calculated at the compact level (release of fission products from the compact). PARFUME calculates the release fraction as the ratio of the number of atoms released from the compact to the amount produced in the compact fuel kernels and through uranium contamination. These safety test predictions aim at giving guidance for the upcoming safety tests to be conducted at ORNL and INL. The AGR-2 compacts modeled in this study belong to the four U.S. capsules of the AGR-2 irradiation test train. For each capsule, the compacts with the lowest and highest burnups were selected to provide a prediction envelope. The objective of this document is to present results of calculations and analyses made by PARFUME on these selected AGR-2 compacts. These results include: • Fuel failure probability • Palladium penetration • Fractional release of fission products Details associated with completion of these calculations are provided in the remainder of this document: the AGR-2 Safety Testing plan is briefly introduced in Section 2, PARFUME modeling is outlined in Section 3, results are described in Section 4, conclusions are given in Section 5, and references are listed in Section 6.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Massively Parallel Bayesian Model Calibration and Uncertainty Quantification with Applications to Nuclear Fuels and Materials

The U.S. Department of Energy (DOE)’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims to develop predictive capabilities by applying computational methods to the analysis and design of advanced reactor and fuel cycle systems. This program has been providing engineering-scale support for the development of BISON, a high-fidelity and high-resolution fuel performance tool. Fuel behavior in a nuclear reactor is governed by a complex network of mechanisms interacting with various other physics aspects in the reactor system. Any model developed to represent the fuel behavior will likely be idealized resulting in uncertainties in their predictions compared to the observed data. As such, this report was motivated by the need to identify the sources of uncertainties and quantify and propagate them through the fuel model outputs. Such quantification of uncertainties will establish a level of model trustworthiness, identify approaches to improve the model trustworthiness, and even guide optimal experiment design for maximal information gain. To accomplish the uncertainty quantification for computational models, this report has relied on the Bayesian framework which provides probabilistic treatment of models their inputs and outputs. The current state-of-the-art on performing Bayesian Uncertainty Quantification (UQ) for nuclear engineering models using High Performance Computing (HPC) resources have been reviewed. Implementation of capabilities for massively parallel Bayesian UQ in Multiphysics Object-Oriented Simulation Environment (MOOSE) is discussed. Several verification cases are discussed to verify the accuracy of the quantified uncertainties using the developed computational capabilities in MOOSE. Then, the problem of quantifying the uncertainties in TRI-Structural isOtropic (TRISO) fuel silver release is addressed. For the first time, the uncertainties arising from the TRISO Fission Gas Release (FGR) model due to model inadequacy and experimental noise are quantified. Also, the Bayesian capabilities are applied to the calibration of the MATPRO creep model, a widely used model in several fuel assessment cases. The impact of the prediction uncertainties in the MATPRO model on the fuel cladding behavior as part of the TRIBULATION assessment case (which is an integral effects case) is investigated. This report concludes with a discussion on the future work for the UQ for computational models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Engine-Aftertreatment in Closed-Loop Modeling for Heavy Duty Truck Emissions Control

An engine-aftertreatment computational model was developed to support in-loop performance simulations of tailpipe emissions and fuel consumption associated with a range of heavy-duty (HD) truck drive cycles. For purposes of this study, the engine-out exhaust dynamics were simulated with a combination of steady-state engine maps and dynamic correction factors that accounted for recent engine operating history. The engine correction factors were approximated as dynamic first-order lags associated with the thermal inertia of the major engine components and the rate at which engine-out exhaust temperature and composition vary as combustion heat is absorbed or lost to the surroundings. The aftertreatment model included catalytic monolith components for diesel exhaust oxidation, particulate filtration, and selective catalytic reduction of nitrogen oxides (NOx) with urea. Both the engine and aftertreatment models have been calibrated with dynamometer measurements from a commercial 2010-certificated 15-L Cummins diesel engine. The fuel consumption engine map with the reduced data is attached in the appendix. Simulations with the combined engine and aftertreatment models above appear to reveal important trends among the fuel efficiency, emissions control, power demand for HD trucks under realistic drive cycle conditions. Thus, this type of computational simulation appears to have significant value in choosing among options for HD vehicle design and operation.

Gao, Zhiming↗

Economic carbon cycle feedbacks may offset additional warming from natural feedbacks

As the Earth warms, carbon sinks on land and in the ocean will weaken, thereby increasing the rate of warming. Although natural mechanisms contributing to this positive climate–carbon feedback have been evaluated using Earth system models, analogous feedbacks involving human activities have not been systematically quantified. Here we conceptualize and estimate the magnitude of several economic mechanisms that generate a carbon–climate feedback, using the Kaya identity to separate a net economic feedback into components associated with population, GDP, heating and cooling, and the carbon intensity of energy production and transportation. We find that climate-driven decreases in economic activity (GDP) may in turn decrease human energy use and thus fossil fuel CO 2 emissions. In a high radiative forcing scenario, such decreases in economic activity reduce fossil fuel emissions by 13% this century, lowering atmospheric CO 2 by over 100 ppm in 2100. The natural carbon–climate feedback, in contrast, increases atmospheric CO 2 over this period by a similar amount, and thus, the net effect including both feedbacks is nearly zero. Our work highlights the importance of improving the representation of climate–economic feedbacks in scenarios of future change. Although the effects of climate warming on the economy may offset weakening land and ocean carbon sinks, a loss of economic productivity will have high societal costs, potentially increasing wealth inequity and limiting resources available for effective adaptation.

54 ENVIRONMENTAL SCIENCES↗

AGR-5/6/7 Irradiation As Run Predictions Using PARFUME

The PARticle FUel ModEl (PARFUME), a fuel performance modeling code used for high-temperature gas-cooled reactors, was used to model the Advanced Gas Reactor (AGR)-5/6/7 irradiation test using as-run physics and thermal data. The AGR-5/6/7 irradiation test consists of the combined fifth, sixth, and seventh planned irradiations of the AGR Fuel Development and Qualification Program. The AGR-5/6/7 test train is a multi-capsule, instrumented experiment that is designed for irradiation in the 133.4-mm diameter northeast flux trap position of the Advanced Test Reactor (ATR) at Idaho National Laboratory. Each capsule contains compacts filled with uranium oxycarbide unaltered fuel particles. This report documents the calculations performed to predict the failure probability of tristructural isotropic (TRISO)-coated fuel particles during the AGR-5/6/7 experiment. In addition, this report documents the calculated fission product release fraction from the fuel. The calculations include modeling of the AGR 5/6/7 irradiation that occurred from February 2018 to July 2020 over nine ATR cycles, including six normal cycles and three power axial locator mechanism cycles, for a total of approximately 376 effective full power days (EFPD). The irradiation conditions and material properties of the AGR-5/6/7 test predicted zero fuel particle failures in Capsules 1, 3, and 4. Fuel particle failures were predicted in two of the compacts in Capsule 2 and one particle failure is predicted in each one of the compacts in Capsule 5. All compacts that exhibited fuel particle failures predicted by PARFUME were caused by localized stress concentrations in the silicon carbide (SiC) layer caused by cracking in the inner pyrolytic (IPyC) layer. In addition, shrinkage of the buffer and IPyC layer during irradiation resulted in formation of a buffer-IPyC gap. Compacts with a lower irradiation temperature and fluence experienced the smallest buffer-IPyC gap formation. Conversely, higher irradiated temperature compacts with a high fluence experienced the largest buffer-IPyC gap formation. Compact 3-6-3 experienced the largest buffer IPyC gap formation of just under 21.7 µm. The release fraction of fission products silver (Ag), cesium (Cs), and strontium (Sr) vary depending on capsule location and irradiation temperature. The maximum release fraction of Ag occurs in Capsule 3, reaching up to 59.5% for the TRISO fuel particles (compact 3-6-3). The release fraction of the other two fission products, Cs and Sr, are much smaller. A maximum Cs release fraction of 1.1% occurred in compact 3-4-3 and 4.4% for Sr in compact 3-6-3.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Full-Cell Model for Direct Toluene Electro-Hydrogenation Electrolysis

Liquid organic hydrogen carriers (LOHCs) are organic molecules that undergo a hydrogenation/dehydrogenation cycle to enable storage and transportation of hydrogen fuel under ambient conditions. One promising LOHC candidate is toluene, which can be converted to methylcyclohexane (MCH) electrochemically, enabling a decarbonized process when green electricity is used. In this study, we developed a full-cell model for the direct electro-hydrogenation of toluene to MCH, utilizing a zero-gap membrane electrode assembly architecture. The model incorporates electrochemical kinetics, ionic transport, water transport across the membrane, and mass transport effects. Electrochemical kinetics are characterized using Tafel analysis on Pt/Ru catalyst. The model is validated against experimental data, including polarization curves, Faradaic efficiencies, and water crossover. A voltage breakdown analysis shows that the performance is dominated by kinetic losses, and the model is used to carry out a comparison of different toluene electro-hydrogenation reaction catalysts. Finally, a sensitivity analysis is conducted on key design parameters illustrating which can be modified to maximize electrolyzer performance. The cathode specific surface area and cathode porous transport layer thickness (PTL) have the largest impact on the current density, while the PTL thickness and Pt loading in the PTL have the largest impact on Faradaic efficiency.

Ehlinger, Victoria M. [Lawrence Livermore National↗

Fuel Cycle Research & Development, Technical Monthly - February 2012

Topics discussed in this monthly report are: (1) MPACT Campaign management and integration; (2) Accounting and control technologies - microcalorimetry, electrochemical sensor, fast neutron multiplicity analysis, lead slowing down spectrometer; (3) MPACT analysis tools - modeling and simulation for analysis of safeguards performance (electrochemical), material control including process monitoring (pattern recognition, sensors), sensor for measuring density and depth of molten electrolyte, MPACT system integration and technical support.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗