Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Improving electrical performance and bias stability of HfInZnO-TFT with optimizing the channel thickness

RF magnetron sputtered HfInZnO film and atomic layer deposition (ALD) Al{sub 2}O{sub 3} film were employed for thin film transistors (TFTs) as channel layer and gate insulator, respectively. To achieve HfInZnO-TFT with high performance and good bias stability, the thickness of HfInZnO active layer was optimized. The performance of HfInZnO-TFTs was found to be thickness dependent. As the HfInZnO active layer got thicker, the leakage current greatly increased from 1.73 × 10{sup −12} to 2.54 × 10{sup −8} A, the threshold voltage decreased from 7.4 to −4.7 V, while the subthreshold swing varied from 0.41 to 1.07 V/decade. Overall, the HfInZnO film showed superior performance, such as saturation mobility of 6.4 cm{sup 2}/V s, threshold voltage of 4.2 V, subthreshold swing of 0.43 V/decade, on/off current ratio of 3 × 10{sup 7} and V{sub th} shift of 3.6 V under V{sub GS}= 10 V for 7200 s. The results demonstrate the possibility of fabricating TFTs using HfInZnO film as active layer and using ALD Al{sub 2}O{sub 3} as gate insulator.

36 MATERIALS SCIENCE↗

Ferroelectrics everywhere: Ferroelectricity in magnesium substituted zinc oxide thin films

We demonstrate ferroelectricity in Mg-substituted ZnO thin films with the wurtzite structure. Zn 1–x Mg x O films are grown by dual-cathode reactive magnetron sputtering on (111)-Pt // (0001)-Al 2 O 3 substrates at temperatures ranging from 26 to 200 °C for compositions spanning from x = 0 to x = 0.37. X-ray diffraction indicates a decrease in the c-lattice parameter and an increase in the a-lattice parameter with increasing Mg content, resulting in a nearly constant c/a axial ratio of 1.595 over this composition range. Transmission electron microscopy studies show abrupt interfaces between Zn 1–x Mg x O films and the Pt electrode. When prepared at pO 2 = 0.025, film surfaces are populated by abnormally oriented grains as measured by atomic force microscopy for Mg concentrations >29%. Raising pO 2 to 0.25 eliminates the misoriented grains. Optical measurements show increasing bandgap values with increasing Mg content. When prepared on a 200 °C substrate, films display ferroelectric switching with remanent polarizations exceeding 100 μC cm –2 and coercive fields below 3 MVcm –1 when the Mg content is between ~30% and ~7%. Substrate temperature can be lowered to ambient conditions, and when doing so, capacitor stacks show only minor sacrifices to crystal orientation and nearly identical remanent polarization values; however, coercive fields drop below 2 MV/cm. Using ambient temperature deposition, we demonstrate ferroelectric capacitor stacks integrated directly with polymer substrate surfaces.

36 MATERIALS SCIENCE↗

Growth and structure of alpha-Ta films for quantum circuit integration

Tantalum films incorporated into superconducting circuits have exhibited low surface losses, resulting in long-lived qubit states. The remaining loss pathways originate in microscopic defects that manifest as two level systems (TLSs) at low temperatures. These defects limit performance, so careful attention to tantalum film structures is critical for optimal use in quantum devices. In this work, we investigate the growth of tantalum using magnetron sputtering on sapphire, Si, and photoresist substrates. In the case of sapphire, we present procedures for the growth of fully-oriented films with α-Ta [1 1 1]//Al2O3 [0 0 0 1] and α-Ta [1 −1 0]//Al2O3 [1 0 −1 0] orientational relationships and having residual resistivity ratio (RRR) ∼ 60 for 220 nm thick films. On Si, we find a complex grain texturing with Ta [1 1 0] normal to the substrate and RRR ∼ 30. We further demonstrate airbridge fabrication using Nb to nucleate α-Ta on photoresist surfaces. For the films on sapphire, resonators show TLS-limited quality factors of 1.3 ± 0.3 × 106 at 10 mK (for a waveguide gap and conductor width of 3 and 6 μm, respectively). Structural characterization using scanning electron microscopy, x-ray diffraction, low temperature transport, secondary ion mass spectrometry, and transmission electron microscopy reveal the dependence of residual impurities and screw dislocation density on processing conditions. The results provide practical insights into the fabrication of advanced superconducting devices including qubit arrays and guide future works on crystallographically deterministic qubit fabrication.

42 ENGINEERING↗

Topochemical Synthesis and Electronic Structure of High-Crystallinity Infinite-Layer Nickelates on an Orthorhombic Substrate

Superconductivity in infinite-layer nickelates has stirred much research interest, to which questions regarding the nature of superconductivity remain elusive. A critical leap forward to address these intricate questions is through the growth of high-crystallinity infinite-layer nickelates, including the “parent” phase. Here, we report the synthesis of a high-quality thin-film nickelate, NdNiO 2 . This is achieved through the growth of a perovskite precursor phase (NdNiO 3 ) of superior crystallinity on the NdGaO 3 substrate by off-axis RF magnetron sputtering and a low-temperature topochemical reduction using NaH. We observe a nonlinear Hall effect at low temperatures in this “non-doped” phase. We further study the electronic properties using advanced X-ray scattering and first-principles calculations. We observe spectroscopic indications of the enhanced two-dimensionality and a reduced hybridization of Nd 5d and Ni 3d orbitals. These findings unlock new pathways for preparing high-quality infinite-layer nickelates and provide new insights into the intrinsic features of these compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ferroelectricity of wurtzite Al 1−x Hf x N heterovalent alloys

Thin films of aluminum hafnium nitride (Al1−xHfxN) were synthesized via reactive magnetron sputtering for Hf contents up to x = 0.13. X-ray diffraction showed a single c-axis oriented wurtzite phase for all films. Hard x-ray photoelectron spectroscopy demonstrated homogeneous Al:Hf distribution through the thin films and confirmed their insulating character. A collection of complementary tests showed unambiguous polarization inversion, and thus ferroelectricity in multiple samples. Current density vs electric field hysteresis measurements showed distinct ferroelectric switching current peaks, the piezoelectric coefficient d 33,f,meas measured using a double beam laser interferometer (DBLI) showed a reversal in sign with similar magnitude, and anisotropic wet etching confirmed field-induced polarization inversion. This demonstrates the possibility of using tetravalent–and not just trivalent–alloying elements to enable ferroelectricity in AlN-based thin films, highlighting the compositional flexibility of ferroelectricity in wurtzites and greatly expanding the chemistries that can be considered for future devices.

36 MATERIALS SCIENCE↗

Resonant surface enhancement of Raman scattering of Ag nanoparticles on silicon substrates fabricated by dc sputtering

Ag nanoparticles (AgNPs) were deposited onto silicon substrates by direct current (dc) magnetron sputtering. The influences of sputtering power and sputtering time on the AgNP film morphology were studied using atomic force microscopy. The particle size was successfully tuned from 19 nm to 53 nm by varying the sputtering time at a dc power of 10 W. When Rhodamine 6 G (R6G) was used as the probe molecule, the AgNP films showed significant surface enhanced Raman scattering effect. In particular, it is found that larger particles show stronger enhancement for lower concentrations of R6G while smaller particles display stronger enhancement for higher concentrations of R6G.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Thermal conductivity of sputtered amorphous Ge films

We measured the thermal conductivity of amorphous Ge films prepared by magnetron sputtering. The thermal conductivity was significantly higher than the value predicted by the minimum thermal conductivity model and increased with deposition temperature. We found that variations in sound velocity and Ge film density were not the main factors in the high thermal conductivity. Fast Fourier transform patterns of transmission electron micrographs revealed that short-range order in the Ge films was responsible for their high thermal conductivity. The results provide experimental evidences to understand the underlying nature of the variation of phonon mean free path in amorphous solids.

36 MATERIALS SCIENCE↗

Unexpected short- and medium-range atomic structure of sputtered amorphous silicon upon thermal annealing

We investigate the structure of magnetron-sputtered (MS) amorphous silicon (a-Si) prepared under standard deposition conditions and compare this to pure ion-implanted (II) a-Si. The structure of both films is characterized in their as-prepared and thermally annealed states. Significant differences are observed in short- and medium-range order following thermal annealing. Whereas II a-Si undergoes structural relaxation toward a continuous random network, MS a-Si exhibits little change. Cross-sectional transmission electron microscopy reveals the presence of nanopores in the MS film consistent with reduced mass-density. Therefore, the short- and medium-range order of annealed, MS a-Si is tentatively attributed to these pores.

36 MATERIALS SCIENCE↗

Investigation of buried homojunctions in p-InP formed during sputter deposition of both indium tin oxide and indium oxide

While dc magnetron sputter deposition of indium tin oxide leads to the formation of a buried homojunction in single crystal p-type InP, the mechanism of type conversion of the InP surface is not apparent. In view of the recent achievement of nearly 17-percent global efficiencies for cells fabricated solely by sputter deposition of In2O3, it is presently surmised that tin may not be an essential element in type conversion. A variety of electrical and optical techniques are presently used to evaluate the changes at both indium tin oxide/InP and indium oxide/InP interfaces. Such mechanisms as the passivation of acceptors by hydrogen, and sputter damage, are found to occur simultaneously.

Gessert, T. A.↗

Composition, morphology and mechanical properties of sputtered TiAlN coating

TiAlN coating was deposited on the tungsten carbide cutting tool by using DC magnetron sputtering system to study the influence of substrate bias and nitrogen flow rate on the composition, morphology and mechanical properties. The negatively substrate bias and nitrogen flow rate was varied from about −79 to −221 V and 30 sccm to 72 sccm, respectively. The coating composition and roughness were characterized by using SEM/EDX and Atomic Force Microscopy (AFM), respectively. The dynamic ultra micro hardness tester was used to measure the mechanical properties. The coating hardness increases to about 10-12 GPa with an increase of the negatively substrate bias up to − 200 V and it tend to decrease with an increase in nitrogen flow rate up to 70 sccm. The increase of hardness follows the increase of Ti and N content and rms coating roughness.

36 MATERIALS SCIENCE↗

Effect of Sputtering Current on the Comprehensive Properties of (Ti,Al)N Coating and High-Speed Steel Substrate

To improve the practical property of (Ti,Al)N coating on a high-speed steel (HSS) substrate, a series of sputtering currents were used to obtain several (Ti,Al)N coatings using a magnetron sputtering equipment. The phase structure, morphology, and components of (Ti,Al)N coatings were characterized by x-ray diffraction, scanning electron microscopy, energy-dispersive x-ray spectroscopy, and x-ray photoelectron spectroscopy, respectively. The performance of (Ti,Al)N coatings, adhesion, hardness, and wear resistance was tested using a scratch tester, micro/nanohardness tester, and tribometer, respectively. Based on the structure–property relationships of (Ti,Al)N coatings, the results show that both the Al content and deposition temperature of (Ti,Al)N coatings increased with sputtering current. A high Al content helped to improve the performance of (Ti,Al)N coatings. However, the HSS substrate was softened during the high sputtering current treatment. Therefore, the optimum sputtering current was determined as 2.5 A that effectively increased the hardness and wear resistance of (Ti,Al)N coating.

36 MATERIALS SCIENCE↗

Characterization of Cu2ZnSnS4 Thin Films Prepared by the Sulfurization of Co-sputtered Metal Precursors

In this work, we report on the synthesis and characterization of Cu2ZnSnS4 (CZTS) thin films prepared by annealing of co-sputtered metal precursors in sulfur atmosphere. Radio-frequency magnetron sputtering was applied to deposit the metal layers from single metal targets on Mo-coated soda-lime glass substrates. The chemical composition of the precursors was controlled by varying the sputtering working power, resulting in films with various compositions. X-ray fluorescence was used to determine the elemental concentration of these metal films. The metal precursors were then converted into CZTS in a tube furnace using different sulfurization conditions to investigate the effect of the annealing process on the properties of the final CZTS films. Film structural characterization and phase identification results were supported by X-ray diffraction (XRD) and Raman spectroscopy. Surface and cross-sectional film morphology was carried out by scanning electron microscopy (SEM). For the sulfurized films, significant Sn loss was noticed. However, the loss of Sn was successfully controlled by depositing precursors with an excess of Sn. After optimizing the composition of the metal precursor, XRD and Raman scattering results revealed single-phase CZTS films without clear signs of secondary phases. SEM showed improved morphology in the form of dense structures and smooth surfaces for the films sulfurized at 600 degrees C. Our first solar cell, based on a CZTS film originating from a precursor sulfurized at 550 degrees C for 60 min, showed an open-circuit voltage of 471 mV, a short-circuit current density of 9.92 mA/cm-2, a fill factor of 36.9%, and an efficiency of 1.72%.

14 SOLAR ENERGY↗

Plasma deposition and surface modification techniques for wear resistance

The ion-assisted or plasma coating technology is discussed as it applies to the deposition of hard, wear resistant refractory compound films. Of the many sputtering and ion plating modes and configurations the reactive magnetron sputtering and the reactive triode ion plating techniques are the preferred ones to deposit wear resistant coatings for tribological applications. Both of these techniques incorporate additional means to enhance the ionization efficiency and chemical reaction to precision tailor desirable tribological characteristics. Interrelationships between film formation, structure, and ribological properties are strictly controlled by the deposition parameters and the substrate condition. The enhanced ionization contributes to the excellent adherence and coherence, reduced internal stresses and improved structural growth to form dense, cohesive, equiaxed grain structure for improved wear resistance and control.

Spalvins, T.↗

Ambient-Temperature Sputtering Of Composite Oxide Films

Technique for deposition of homogeneous films of multicomponent oxides on substrates at ambient temperature based on sequential sputter deposition of individual metal components, as alternating ultra-thin layers, from multiple targets. Substrates rotated over sputtering targets of lead, zirconium, and titanium. Dc-magnetron sputtering of constituent metals in reactive ambient of argon and oxygen leads to formation of the respective metal oxides intermixed on extremely fine scale in desired composition. Compatible with low-temperature microelectronic processing.

Thakoor, Sarita↗

Photoluminescence of as-grown and thermal annealed SiO{sub x}/Si-nanocrystals heterolayers grown by reactive rf sputtering

SiO{sub x}/Si-nanocrystals (Si NCs) heterolayers were fabricated employing a rf magnetron sputtering system. The synthesis process, through modification of the oxygen partial pressure of the plasma, promotes the synthesis of stoichiometric SiO{sub 2} layers and affect the Si NCs layer giving place to SiO{sub x}/Si NCs (1.64<x<2) interfaces. All as-grown samples showed strong photoluminescence (PL) bands in the visible and near-infrared regions; transmission electron microscopy measurements confirmed the presence of Si NCs. Thermal annealing at 1100 deg. C promoted the SiO{sub 2} stoichiometry in the interface and the crystallization of more Si NCs. The results allow us to clearly identify the origin of the PL bands; indicating that the near-infrared emission is related to the nonstoichiometric oxide while the red and green bands are originated in Si NCs.

36 MATERIALS SCIENCE↗

Influence of process parameters on properties of reactively sputtered tungsten nitride thin films

Tungsten nitride (WN{sub x}) thin films were produced by reactive dc magnetron sputtering of tungsten in an Ar-N{sub 2} gas mixture. The influence of the deposition power on the properties of tungsten nitride has been analyzed and compared with that induced by nitrogen content variation in the sputtering gas. A combined analysis of structural, electrical and optical properties on thin WN{sub x} films obtained at different deposition conditions has been performed. It was found that at an N{sub 2} content of 14% a single phase structure of W{sub 2}N films was formed with the highest crystalline content. This sputtering gas composition was subsequently used for fabricating films at different deposition powers. Optical analysis showed that increasing the deposition power created tungsten nitride films with a more metallic character, which is confirmed with resistivity measurements. At low sputtering powers the resulting films were crystalline whereas, with an increase of power, an amorphous phase was also present. The incorporation of an excess of nitrogen atoms resulted in an expansion of the W{sub 2}N lattice and this effect was more pronounced at low deposition powers. Infrared analysis revealed that in WN{sub x} films deposited at low power, chemisorbed N{sub 2} molecules did not behave as ligands whereas at high deposition power they clearly appeared as ligands around metallic tungsten. In this study, the influence of the most meaningful deposition parameters on the phase transformation reaction path was established and deposition conditions suitable for producing thermally stable and highly crystalline W{sub 2}N films were found.

36 MATERIALS SCIENCE↗

Vanadium oxide thin films for bolometric applications deposited by reactive pulsed dc sputtering

Vanadium oxide (VO{sub x}) thin films were deposited by reactive pulse dc magnetron sputtering process using a pure vanadium metal target. The structural, microstructure, and electrical properties were correlated as a function of processing parameters such as substrate temperature, Ar:O partial pressures ratios, and pulsed dc power to fabricate these films. The VO{sub x} films deposited at various substrate temperatures between 30 and 300 degree sign C using a range of oxygen to argon partial pressure ratios exhibited huge variation in their microstructure even though most of them are amorphous to x-ray diffraction technique. In addition, the electrical properties such as temperature coefficient of resistance (TCR), resistivity, and noise levels were influenced by film microstructure. The TCRs of the VO{sub x} films were in the range of -1.1% to -2.4% K{sup -1} having resistivity values of 0.1-100 {Omega} cm. In particular, films grown at lower substrate temperatures with higher oxygen partial pressures have shown finer columnar grain structure and exhibited larger TCR and resistivity.

36 MATERIALS SCIENCE↗

Buried homojunction solar cells formed in p-InP during sputter deposition and hydrogen plasma processing

Although it is apparent that direct current (DC) magnetron sputter deposition of indium tin oxide (ITO) leads to the formation of a buried homojunction in single-crystal p-type InP, the actual mechanism of type conversion of the InP surface is not clear. Since sputter deposition of In2O3 has also led to high-quality cells, it appears that Sn is not the cause of type conversion. To investigate the junction formation process further, experiments involving the use of a pure hydrogen plasma have been performed, resulting in type conversion of Fe-doped InP surfaces and in solar cells with efficiencies over 16 percent (global). The results confirm that sputter deposition is not necessary to form this type of buried homojunction solar cell, and they suggest a fabrication process that may be used with other relevant photovoltaic materials.

Gessert, T. A.↗