Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Hypersonic research engine project. Phase 2: Some combustor test results of NASA aerothermodynamic integration model

Combustor test results of the NASA Aerothermodynamic Integration Model are presented of a ramjet engine developed for operation between Mach 3 and 8. Ground-based and flight experiments which provide the data required to advance the technology of hypersonic air-breathing propulsion systems as well as to evaluate facility and testing techniques are described. The engine was tested with synthetic air at Mach 5, 6, and 7. The hydrogen fuel was heated to 1500 R prior to injection to simulate a regeneratively cooled system. Combustor efficiencies up to 95 percent at Mach 6 were achieved. Combustor process in terms of effectiveness, pressure integral factor, total pressure recovery and Crocco's pressure-area relationship are presented and discussed. Interactions between inlet-combustor, combustor stages, combustor-nozzle, and the effects of altitude, combustor step, and struts are observed and analyzed.

Sun, Y. H.↗

Effect of Exhaust Pressure on the Cooling Characteristics of a Liquid-Cooled Engine

Data for a liquid-cooled engine with a displacement volume of 1710 cubic inches were analyzed to determine the effect of exhaust pressure on the engine cooling characteristics. The data covered a range of exhaust pressures from 7 to 62 inches of mercury absolute, inlet-manifold pressures from 30 to 50 inches of mercury absolute, engine speeds from 1600 to 3000 rpm, and fuel-air ratios from 0.063 to 0.100. The effect of exhaust pressure on engine cooling was satisfactorily incorporated in the NACA cooling-correlation method as a variation in effective gas temperature with exhaust pressure. Large variations of cylinder-head temperature with exhaust pressure were obtained for operation at constant charge flow. At a constant charge flow of 2 pounds per second (approximately 1000 bhp) and a fuel-air ratio of 0.085, an increase in exhaust pressure from 10 to 60 inches of mercury absolute resulted in an increase of 40 F in average cylinder-head temperature. For operation at constant engine speed and inlet-manifold pressure and variable exhaust pressure (variable charge flow), however, the effect of exhaust pressure on cylinder-head temperature is small. For example, at an inlet-manifold pressure of 40 inches of mercury absolute, an engine speed of 2400 rpm.- and a fuel-air ratio of 0.085, the average cylinder-head temperature was about the same at exhaust pressures of 10 and 60 inches of,mercury absolute; a rise and a subsequent decrease of about 70 occurred between these extremes.

Doyle, Ronald B.↗

Computer simulation analysis of the behavior of renal-regulating hormones during hypogravic stress

A computer simulation of a mathematical circulation model is used to study the alterations of body fluids and their electrolyte composition that occur in weightlessness. The behavior of the renal-regulating hormones which control these alterations is compared in simulations of several one-g analogs of weightlessness and space flight. It is shown that the renal-regulating hormones represent a tightly coupled system that responds acutely to volume disturbances and chronically to electrolyte disturbances. During hypogravic conditions these responses lead to an initial suppression of hormone levels and a long-term effect which varies depending on metabolic factors that can alter the plasma electrolytes. In addition, it is found that if pressure effects normalize rapidly, a transition phase may exist which leads to a dynamic multiphasic endocrine response.

Leonard, J. I.↗

Minimum Specific Fuel Consumption of a Liquid-Cooled Multicylinder Aircraft Engine as Affected by Compression Ratio and Engine Operating Conditions

An investigation was conducted on a 12-cylinder V-type liquid-cooled aircraft engine of 1710-cubic-inch displacement to determine the minimum specific fuel consumption at constant cruising engine speed and compression ratios of 6.65, 7.93, and 9.68. At each compression ratio, the effect.of the following variables was investigated at manifold pressures of 28, 34, 40, and 50 inches of mercury absolute: temperature of the inlet-air to the auxiliary-stage supercharger, fuel-air ratio, and spark advance. Standard sea-level atmospheric pressure was maintained at the auxiliary-stage supercharger inlet and the exhaust pressure was atmospheric. Advancing the spark timing from 34 deg and 28 deg B.T.C. (exhaust and intake, respectively) to 42 deg and 36 deg B.T.C. at a compression ratio of 6.65 resulted in a decrease of approximately 3 percent in brake specific fuel consumption. Further decreases in brake specific fuel consumption of 10.5 to 14.1 percent (depending on power level) were observed as the compression ratio was increased from 6.65 to 9.68, maintaining at each compression ratio the spark advance required for maximum torque at a fuel-air ratio of 0.06. This increase in compression ratio with a power output of 0.585 horsepower per cubic inch required a change from . a fuel- lend of 6-percent triptane with 94-percent 68--R fuel at a compression ratio of 6.65 to a fuel blend of 58-percent, triptane with 42-percent 28-R fuel at a compression ratio of 9.68 to provide for knock-free engine operation. As an aid in the evaluation of engine mechanical endurance, peak cylinder pressures were measured on a single-cylinder engine at several operating conditions. Peak cylinder pressures of 1900 pounds per square inch can be expected at a compression ratio of 9.68 and an indicated mean effective pressure of 320 pounds per square inch. The engine durability was considerably reduced at these conditions.

Brun, Rinaldo J.↗

Predicting Large-scale Effects During Cookoff of Plastic-Bonded Explosives (PBX 9501 PBX 9502 and LX-14)

In this study, we have made reasonable cookoff predictions of large-scale explosive systems by using pressure-dependent kinetics determined from small-scale experiments. Scale-up is determined by properly accounting for pressure generated from gaseous decomposition products and the volume that these reactive gases occupy, e.g. trapped within the explosive, the system, or vented. The pressure effect on the decomposition rates has been determined for different explosives by using both vented and sealed experiments at low densities. Low-density explosives are usually permeable to decomposition gases and can be used in both vented and sealed configurations to determine pressure-dependent reaction rates. In contrast, explosives that are near the theoretical maximum density (TMD) are not as permeable to decomposition gases, and pressure-dependent kinetics are difficult to determine. Ignition in explosives at high densities can be predicted by using pressure-dependent rates determined from the low-density experiments as long as gas volume changes associated with bulk thermal expansion are also considered. In the current work, cookoff of the plastic-bonded explosives PBX 9501 and PBX 9502 is reviewed and new experimental work on LX-14 is presented. Reactive gases are formed inside these heated explosives causing large internal pressures. The pressure is released differently for each of these explosives. For PBX 9501, permeability is increased and internal pressure is relieved as the nitroplasticizer melts and decomposes. Internal pressure in PBX 9502 is relieved as the material is damaged by cracks and spalling. For LX-14, internal pressure is not relieved until the explosive thermally ignites. The current paper is an extension of work presented at the 26th ICDERS symposium [1].

42 ENGINEERING↗

Element-resolved magnetism across the temperature- and pressure-induced spin reorientation in MnBi

Rare-earth free permanent magnet MnBi (NiAs-type crystal structure) displays strong magnetic anisotropy above its 90 K spin reorientation transition (SRT). X-ray magnetic circular dichroism (XMCD) shows induced magnetism in Bi 5d band, which is strongly coupled to the magnetism of Mn. A clear increase in Bi orbital-to-spin moment ratio is observed above the SRT. Hydrostatic pressure mimics the e*ect of temperature on the SRT, and the pressure effect also leads to anisotropic lattice contraction, which is known to be induced by cooling. These results reveal that temperature and pressure can similarly induce the coupled structural and magnetic responses, suggesting the importance of the anisotropic lattice change and Mn-Bi hybridization to the magnetic anisotropy change across the SRT.

36 MATERIALS SCIENCE↗

Phase Transitions in Lead Hafnate under High Pressure

The effect of hydrostatic pressure on phase transitions in lead hafnate (PbHfO{sub 3}) has been studied by the methods of X-ray diffraction and X-ray diffuse scattering. The measurements were performed in the temperature range of 182 < T < 316°C and the pressure range of 1.6 < P < 2.6 GPa. Four regions characterized by different X-ray diffraction patterns and corresponding to an antiferroelectric phase, phases with a long-wavelength modulation of the lead sublattice, and phases with different distortions of the oxygen sublattice are identified. In the temperature region immediately above the region of phases with a long-wavelength modulation, a temperature-dependent maximum in the distribution of diffuse scattering was detected, which means that such a modulation is formed due to condensation of an incommensurate soft mode.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of oxygen pressure on structural and magnetic properties of YIG thin films

The effect of oxygen pressure (P{sub O2}) on the Yttrium Iron Garnet (YIG) thin films were grown on silicon substrate by rf sputtering method was studied. The as-deposited films at 300K were amorphous in nature. The crystallization of these films was achieved by annealing at a temperature of 800 deg. C/1hr in air. The structural, microstructural and magnetic properties were found to be dependent on P{sub O2}.

36 MATERIALS SCIENCE↗

The effect of ambient pressure on the performance of a resistojet

Tests were conducted to investigate the effect of ambient pressure on the measured thrust of a prototype resistojet. The tests were performed using both heated and unheated nitrogen as the propellant at flow rates of 0.0379 and 0.0759 g/s. For the cold flow tests there was no effect on specific impulse over a range of ambient pressures from 1 to 400 microns. The results for the hot flow tests did show as much as a 7 percent variation in specific impulse over the same range of ambient pressures.

Manzella, D. H.↗

Pressure-induced spin crossover in a Fe 78 Si 9 B 13 metallic glass

The pressure effect on structures and properties of a Fe 78 Si 9 B 13 metallic glass was investigated by in situ high-pressure synchrotron Fe Kβ x-ray emission spectroscopy and x-ray diffraction, and electrical resistivity measurements up to ~51 GPa. The study reveals a reversible and continuous pressure-induced high- to low-spin crossover of Fe atoms in an amorphous structure. The changes of the local spin moment can be scaled to match its average atomic distance shrinkage very well during compression. The crossover of electronic spin states in the Fe 78 Si 9 B 13 metallic glass resembles that of typical crystalline Fe-bearing materials but without a sharp atomic volume collapse and an abrupt electrical resistivity jump. Furthermore, these findings could help guide applications of Fe-based metallic glasses as a soft ferromagnetic material at extreme conditions and also improve our understanding of magnetism and coupling of its changes with disordered atomic structures and other properties in metallic glasses.

36 MATERIALS SCIENCE↗

Alfven waves in a two-fluid model of the solar wind.

A two-fluid model for the solar wind is presented that includes the presence of Alfven waves which originate at the sun. The effective pressure of these Alfven waves is considered, as well as a model representation for proton heating through nonlinear Alfven wave damping. The effects of rotation in the solar equatorial plane are allowed for. The implications of the computational results obtained are discussed.

Hollweg, J. V.↗

Venus - On the phase variation of CO2 line profiles

The shapes of Venus' CO2 profiles are found to vary with solar phase angle. High-resolution spectra of the P16 and P14 lines in the 8689- and 7820-A bands, respectively, are presented for phase angles ranging from 6 to 158 deg. The scattering mean free path at 80 mbar, approximately the effective pressure, is 1.7 km. Use of the van de Hulst (1974) similarity relations with simple parametric scattering models is inadequate to separate effects due to the scattering phase function from those due to inhomogeneities in depth when one attempts to determine the atmospheric structure by fitting a family of such models over a wide range of phase angles.

Macy, W., Jr.↗

Jupiter's atmosphere - Observations and interpretation of the microwave spectrum near 1.25-cm wavelength

Measurements of Jupiter's disk-temperature spectrum in the 20- to 24-GHz (1.5 cm less than lambda less than 1.25 cm) region are reported. These data are combined with previously published data to produce a uniformly calibrated thermal spectrum of Jupiter in the wavelength interval 0.85 to 2.1 cm. Model studies are carried out to determine optimum pressure-temperature profiles for an assumed radiative-convective temperature structure. It is found that the temperature at the 1-bar total effective pressure level is between 140 and 165 K, with a most probable value of 153 K, provided that NH3 is uniformly saturated in the clouds on a global scale. We show that the temperature profile for the microwave model is approximately 20 K cooler than the profiles derived from infrared data. An explanation of this discrepancy is discussed in terms of a model which invokes different NH3 distributions in the belts and zones.

Klein, M. J.↗

Surge Pressure Testing of Flight-Like Components

This project studies the transient surge pressure effects (such as those observed during propulsion system priming) on flight components. A water flow setup was used to impart transient surge pressures on flight-like components. The project compared the point of component failure for transient surge pressures versus static proof pressures. Results showed that designing to keep surge pressures below component proof pressures is overly conservative, because the components can handle higher transient pressures. The tests performed on burst discs showed that the rupture pressure under a transient surge pressure was at least 20% above the static rupture pressure. A tested pressure transducer remained fully functional and accurate after surge pressures 60% above its specified proof pressure. A thruster valve was exposed to transient surge pressures four times its specified proof pressure and showed no indications of damage.

propulsion components↗

Supercritical droplet combustion and related transport phenomena

An overview of recent advances in theoretical analyses of supercritical droplet vaporization and combustion is conducted. Both hydrocarbon and cryogenic liquid droplets over a wide range of thermodynamic states are considered. Various important high-pressure effects on droplet behavior, such as thermodynamic non-ideality, transport anomaly, and property variation, are reviewed. Results indicate that the ambient gas pressure exerts significant control of droplet gasification and burning processes through its influence on fluid transport, gas-liquid interfacial thermodynamics, and chemical reactions. The droplet gasification rate increases progressively with pressure. However, the data for the overall burnout time exhibit a considerable change in the combustion mechanism at the criticl pressure, mainly as a result of reduced mass diffusivity and latent heat of vaporization with increased pressure. The influence of droplet size on the burning characteristics is also noted.

Yang, Vigor↗

Linear gyrokinetic simulation of high-n toroidal Alfven eigenmodes in a burning plasma

A hybrid gyrokinetic ions/massless fluid electron model is used to study the stability of high-n toroidal Alfven eigenmodes (TAEs) in ITER [M. Shimada et al., Nucl. Fusion 47, S1 (2007)]. The hybrid model has been implemented in the particle-in-cell turbulence simulation code GEM [Y. Chen and S. E. Parker, J. Comput. Phys. 220, 839 (2007)]. The adequacy of the hybrid model for simulating TAEs has been previously demonstrated [J. Lang et al., Phys. Plasmas 16, 102101 (2009)] by comparing the simulated TAE mode frequency and structure with an eigenmode analysis, and the thermal ion kinetic damping effect with analytic theory. By using a global particle-in-cell code the effects of large orbit width and nonlocal mode structures can be accurately included. Damping rate due to numerical filtering is carefully monitored, and convergence with respect to particle number, grid resolution, etc., is thoroughly tested. The simulations show that the most unstable modes in ITER lie in the rage of 10<n<20. Thermal ion pressure effect and alpha particle nonperturbative effect are important in determining the mode radial location and stability threshold. The thermal ion Landau damping rate and radiative damping rate from the simulations are compared with analytical estimates. The thermal ion Landau damping is the dominant damping mechanism. Plasma elongation has a strong stabilizing effect on the alpha driven TAEs. The central alpha particle pressure threshold for the most unstable n=15 mode is about {beta}{sub {alpha}(0)}=0.7% for the fully shaped ITER equilibrium.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of gas pressure on 60/13.56 MHz dual-frequency capacitively coupled plasmas

The electron energy probability functions (EEPFs) were measured with increasing gas pressure in 60/13.56 MHz dual-frequency capacitively coupled plasma (DF-CCP) using compensated Langmiur electrostatic probe. The transition pressure of heating mode from collisionless to collisional heating in 60/13.56 MHz DF-CCP is found to be significantly lower than that in 13.56 MHz single-frequency CCP. As the pressure increases, the EEPFs change from bi-Maxwellian to Druyvesteyn type which is similar with that in 60 MHz single-frequency CCP. The pressure dependence of electron densities, effective electron temperatures, floating potentials, and plasma potentials in 60/13.56 MHz DF-CCP were measured and were compared with that in 60 MHz single-frequency CCP. The pressure dependence of these plasma parameters in 60/13.56 MHz DF-CCP is similar with that in 60 MHz single-frequency CCP.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗