Search NASA⌕ Search

SEARCH · Search NASA

Results for “Parameter optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

On the theory of the synthesis of offset dual-shaped reflectors - Case examples

In an earlier paper by Galindo-Israel et al. (1987), the geometrical optics (GO) principles, constraints, and requirements of the dual- and single-offset-shaped reflector synthesis problem were collected and developed into a set of nonlinear first-order PDEs. An extension of the methods by which solutions to the PDEs can be obtained is presented, together with several case examples. These examples are independently analyzed by GO and physical optics diffraction methods. The starting point for the integration over each reflector can be taken on the outer rim, at the center, or at an intermediate point-the intermediate starting point being the more general case. The utility of the speed of this synthesis method is demonstrated. For example, the program utilized completes a synthesis in less than 45 s on a 386/20 personal computer and within a fraction of a second on a mainframe Cray. This makes practical the incorporation of the synthesis into a search algorithm that can optimize one or more parameters of the reflector system. As an example, the optimization of the mapping equations for low cross polarization is discussed.

Galindo-Israel, Victor↗
NASA NTRS2001

A Robust Design Methodology for Optimal Microscale Secondary Flow Control in Compact Inlet Diffusers

It is the purpose of this study to develop an economical Robust design methodology for microscale secondary flow control in compact inlet diffusers. To illustrate the potential of economical Robust Design methodology, two different mission strategies were considered for the subject inlet, namely Maximum Performance and Maximum HCF Life Expectancy. The Maximum Performance mission maximized total pressure recovery while the Maximum HCF Life Expectancy mission minimized the mean of the first five Fourier harmonic amplitudes, i.e., 'collectively' reduced all the harmonic 1/2 amplitudes of engine face distortion. Each of the mission strategies was subject to a low engine face distortion constraint, i.e., DC60<0.10, which is a level acceptable for commercial engines. For each of these missions strategies, an 'Optimal Robust' (open loop control) and an 'Optimal Adaptive' (closed loop control) installation was designed over a twenty degree angle-of-incidence range. The Optimal Robust installation used economical Robust Design methodology to arrive at a single design which operated over the entire angle-of-incident range (open loop control). The Optimal Adaptive installation optimized all the design parameters at each angle-of-incidence. Thus, the Optimal Adaptive installation would require a closed loop control system to sense a proper signal for each effector and modify that effector device, whether mechanical or fluidic, for optimal inlet performance. In general, the performance differences between the Optimal Adaptive and Optimal Robust installation designs were found to be marginal. This suggests, however, that Optimal Robust open loop installation designs can be very competitive with Optimal Adaptive close loop designs. Secondary flow control in inlets is inherently robust, provided it is optimally designed. Therefore, the new methodology presented in this paper, combined array 'Lower Order' approach to Robust DOE, offers the aerodynamicist a very viable and economical way of exploring the concept of Robust inlet design, where the mission variables are brought directly into the inlet design process and insensitivity or robustness to the mission variables becomes a design objective.

Anderson, Bernhard H.↗
NASA NTRS1987

STAEBL/general composites with hygrothermal effects (STAEBL/GENCOM)

A computer code has been developed to perform structural optimization of turbine blades made from angle ply fiber composite laminates. Design variables available for optimization include geometric parameters such as blade thickness distribution and root chord, and composite material parameters such as ply angles and numbers of plies of each constituent material. Design constraints include resonance margins, forced response margins, maximum stress, and maximum ply combined stress. A general description of this code is given. Design optimization studies for typical blades are presented.

Rubenstein, Robert↗
NASA NTRS1988

STAEBL/General composites with hygrothermal effects (STAEBL/GENCOM)

A computer code has been developed to perform structural optimization of turbine blades made from angle ply fiber composite laminates. Design variables available for optimization include geometric parameters such as blade thickness disribution and root chord, and composite material parameters such as ply angles and numbers of plies of each constituent material. Design constraints include resonance margins, forced response margins, maximum stress, and maximum ply combined stress. A general description of this code is given. Design optimization studies for typical blades are presented.

Rubinstein, R.↗
NASA NTRSDate not supplied

Parametric Optimization of Rigid Wheels for Planetary Surface Mobility Applications

Design-Build-Test approaches for spaceflight hardware are time and cost intensive, which can result in suboptimal mechanism designs. Optimization-based approaches that utilize high-fidelity models and physics simulation could overcome these limitations while simultaneously speeding up the mechanical design process and reducing cost. In this work, we present a toolchain that enables the multi-objective optimization of rigid rover wheels for planetary surface mobility applications. The toolchain uses Chrono’s Continuous Representation Model (CRM) functionality to simulate granular soil and performs multi-objective parametric optimization on candidate rover wheels to meet a desired performance criterion. The resulting wheel design is then evaluated experimentally using a single-wheel testbed. We end with a discussion of how the toolchain can be extended to simultaneously co-optimize other system parameters, such as system power consumption and feedback control gains.

Optimization↗
NASA NTRSDate not supplied

Additive Manufactured Ultra-Fine Lattice Structures for Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultra-fine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray micro-focus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar R Mireles↗
NASA NTRS2020

Additive Manufactured Ultra-Fine Lattice Structures for Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultrafine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray microfocus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar R Mireles↗
NASA NTRSDate not supplied

Additive Manufacture of Ultra-Fine Lattice Structures of Green Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultrafine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray microfocus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar Mireles↗
NASA NTRS2019

Uncertainty in Soil Moisture Retrievals: an Ensemble Approach Using SMOS L-Band Microwave Data

The uncertainty of soil moisture (SM) retrievals from satellite brightness temperature (TB) observations depends primarily on the choice of radiative transfer model (RTM) parameters, prior SM information and TB inputs. This paper studies the sensitivity of several (quasi-)operational and experimental SM retrieval products from the Soil Moisture Ocean Salinity (SMOS) mission to these choices at 11 reference sites, located in 7 watersheds across the United States (US). Different literature-based RTM parameter sets cause large biases between retrievals. Whereas typical RTM parameter sets are calibrated for SM retrievals, it is shown that a parameter set carefully optimized for TB forward modeling can also be used for retrieving SM. It is also shown that the inclusion of dynamic prior SM estimates in a Bayesian retrieval scheme can strongly improve SM retrievals, regardless of the choice of RTM parameters, and that the use of multi-angular and multi-polarization TB does not necessarily lead to superior retrievals compared to retrievals based on TB data at a single incidence angle and polarization. The second part of this paper evaluates ensemble uncertainty metrics for SM retrievals obtained by propagating a wide range of RTM parameters through the RTM. As expected for bounded variables, the spread in the ensemble SM retrievals is smallest for wet and dry SM values and highest for intermediate SM values. After removal of the strong long-term mean bias associated with the RTM parameter values for individual ensemble members, the remaining anomaly ensemble SM spread of 0.037 cu m/cu m approximates the actual time series unbiased root-mean-square-difference of 0.042 cu m/cu m between ensemble mean retrievals and in situ reference data across the reference sites. However, the temporal variability in the anomaly ensemble spread reveals higher-order biases in the retrieval error, which should be accounted for when characterizing retrieval error.

Jan Quets↗
NASA NTRS2021

Generation-based Evolutionary Tool for the Optimization of Constellations (GenETOC)

With the rapid growth in the capabilities of smaller satellites, satellite architectures that replace a single, extremely capable spacecraft with multiple, cheaper ones are gaining in popularity. Unfortunately, the orbit design process for constellations can be significantly more involved, especiallywhen the relative placement of the individual spacecraft within the constellation is not constrained by mission and/or science objectives. Optimizing a satellite constellation in the presence of multiple, competing objectives is a highly complex problem to which many traditional mathematical optimization methods cannot be applied and few tools exist to help mission designers search for promising candidate mission designs. The Generation-based Evolutionary Tool for the Optimization of Constellations (GenETOC) has been created to search for near-optimal constellation design options. GenETOC combines a modified version of the Non-dominated Sorting Genetic Algorithm II (NSGA II) with STK Components libraries (a 3rdparty .NET package created by Analytical Graphics Inc.) to create a framework that enables a mission designer to generate a simulation that models the design problem and obtain a family of potential, near-optimal solutions that can be investigated more in detail. GenETOC was developed in C# using the .NET framework with Windows Presentation Foundation (WPF) serving as the framework from which to create the graphical user interface (GUI). GenETOC user inputs can be categorized into three major data components: definition of the problem (areas of interest, satellite decision parameters, and sensor configurations), definition of performance objectives, and specification of the genetic algorithm (GA) parameters. In the problem definition component, the user is prompted to define the areas of interest against which the performance metrics will be computed, define the sensor parameters and attach them to specific spacecraft, select which satellite orbital parameters will be added to the decision space of the GA, and specify the range of desired values for each optimization parameter. For performance objectives, the user is presented with a list of available coverage and revisit performance based calculation options from which two metrics are chosen to serve as the objective functions that the GA will use to evaluate solutions during the optimization process. Finally, the definition of the GA parameters provides user control over the number of generations (number of optimization iterations), the population size (number of candidate constellations created in each generation), and the adaptive mutation and crossover threshold values (control parameters for how frequently each process occurs during the optimization). GenETOC has been extensively tested to verify the individual components of the optimization process. The GA has been tested against a suite of GA test problems to confirm convergence to the known two and three-dimensional Pareto fronts. The coverage and revisit performance metrics obtained in GenETOC are compared with STK desktop scenarios, confirming the constellations are being appropriately modeled within GenETOC simulations. A walkthrough of a simple, example problem is provided to illustrate the workings of GenETOC and to demonstrate the output available to the mission designer.

mission design↗
NASA NTRS1974

An assessment of separable fluid connector system parameters to perform a connector system design optimization study

The key to optimization of design where there are a large number of variables, all of which may not be known precisely, lies in the mathematical tool of dynamic programming developed by Bellman. This methodology can lead to optimized solutions to the design of critical systems in a minimum amount of time, even when there are a great number of acceptable configurations to be considered. To demonstrate the usefulness of dynamic programming, an analytical method is developed for evaluating the relationship among existing numerous connector designs to find the optimum configuration. The data utilized in the study were generated from 900 flanges designed for six subsystems of the S-1B stage of the Saturn 1B space carrier vehicle.

Prasthofer, W. P.↗
NASA NTRS1995

Analysis of filter tuning techniques for sequential orbit determination

This paper examines filter tuning techniques for a sequential orbit determination (OD) covariance analysis. Recently, there has been a renewed interest in sequential OD, primarily due to the successful flight qualification of the Tracking and Data Relay Satellite System (TDRSS) Onboard Navigation System (TONS) using Doppler data extracted onboard the Extreme Ultraviolet Explorer (EUVE) spacecraft. TONS computes highly accurate orbit solutions onboard the spacecraft in realtime using a sequential filter. As the result of the successful TONS-EUVE flight qualification experiment, the Earth Observing System (EOS) AM-1 Project has selected TONS as the prime navigation system. In addition, sequential OD methods can be used successfully for ground OD. Whether data are processed onboard or on the ground, a sequential OD procedure is generally favored over a batch technique when a realtime automated OD system is desired. Recently, OD covariance analyses were performed for the TONS-EUVE and TONS-EOS missions using the sequential processing options of the Orbit Determination Error Analysis System (ODEAS). ODEAS is the primary covariance analysis system used by the Goddard Space Flight Center (GSFC) Flight Dynamics Division (FDD). The results of these analyses revealed a high sensitivity of the OD solutions to the state process noise filter tuning parameters. The covariance analysis results show that the state estimate error contributions from measurement-related error sources, especially those due to the random noise and satellite-to-satellite ionospheric refraction correction errors, increase rapidly as the state process noise increases. These results prompted an in-depth investigation of the role of the filter tuning parameters in sequential OD covariance analysis. This paper analyzes how the spacecraft state estimate errors due to dynamic and measurement-related error sources are affected by the process noise level used. This information is then used to establish guidelines for determining optimal filter tuning parameters in a given sequential OD scenario for both covariance analysis and actual OD. Comparisons are also made with corresponding definitive OD results available from the TONS-EUVE analysis.

Lee, T.↗
NASA NTRS2000

Improved Speech Coding Based on Open-Loop Parameter Estimation

A nonlinear optimization algorithm for linear predictive speech coding was developed early that not only optimizes the linear model coefficients for the open loop predictor, but does the optimization including the effects of quantization of the transmitted residual. It also simultaneously optimizes the quantization levels used for each speech segment. In this paper, we present an improved method for initialization of this nonlinear algorithm, and demonstrate substantial improvements in performance. In addition, the new procedure produces monotonically improving speech quality with increasing numbers of bits used in the transmitted error residual. Examples of speech encoding and decoding are given for 8 speech segments and signal to noise levels as high as 47 dB are produced. As in typical linear predictive coding, the optimization is done on the open loop speech analysis model. Here we demonstrate that minimizing the error of the closed loop speech reconstruction, instead of the simpler open loop optimization, is likely to produce negligible improvement in speech quality. The examples suggest that the algorithm here is close to giving the best performance obtainable from a linear model, for the chosen order with the chosen number of bits for the codebook.

Juang, Jer-Nan↗
NASA NTRS1993

Grid and aerodynamic sensitivity analyses of airplane components

An algorithm is developed to obtain the grid sensitivity with respect to design parameters for aerodynamic optimization. The procedure is advocating a novel (geometrical) parameterization using spline functions such as NURBS (Non-Uniform Rational B-Splines) for defining the wing-section geometry. An interactive algebraic grid generation technique, known as Two-Boundary Grid Generation (TBGG) is employed to generate C-type grids around wing-sections. The grid sensitivity of the domain with respect to geometric design parameters has been obtained by direct differentiation of the grid equations. A hybrid approach is proposed for more geometrically complex configurations such as a wing or fuselage. The aerodynamic sensitivity coefficients are obtained by direct differentiation of the compressible two-dimensional thin-layer Navier-Stokes equations. An optimization package has been introduced into the algorithm in order to optimize the wing-section surface. Results demonstrate a substantially improved design due to maximized lift/drag ratio of the wing-section.

Sadrehaghighi, Ideen↗
NASA NTRS1991

Improved silicon nitride for advanced heat engines

The results of a four year program to improve the strength and reliability of injection-molded silicon nitride are summarized. Statistically designed processing experiments were performed to identify and optimize critical processing parameters and compositions. Process improvements were monitored by strength testing at room and elevated temperatures, and microstructural characterization by optical, scanning electron microscopes, and scanning transmission electron microscope. Processing modifications resulted in a 20 percent strength and 72 percent Weibull slope improvement of the baseline material. Additional sintering aids screening and optimization experiments succeeded in developing a new composition (GN-10) capable of 581.2 MPa at 1399 C. A SiC whisker toughened composite using this material as a matrix achieved a room temperature toughness of 6.9 MPa m(exp .5) by the Chevron notched bar technique. Exploratory experiments were conducted on injection molding of turbocharger rotors.

Yeh, Harry C.↗